Measuring & Analyzing Instruments

The round jaw design on the P50 Series clamp on current probes along with the high content nickel metal core makes them well suited for power quality applications where high accuracy and low phase shift along with wide frequency are important. Measurement range is 1mA to 1200A. The P50 clamp current transformer is a general purpose 1000A AC current probe designed for use with DMMs, loggers and other instruments that have a current input. It has a 1000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw. The P50 clamp current probe has an integral 2.5m lead terminated. The rounded jaw design on this probe makes it well-suited for power applications where high accuracy 0.1% and low phase shift and wide frequency response are important. Electrical parameters Ratio: 1000: 1 or 2000:1 (customized) Accuracy class: 0.1%, 0.2%, 0.5% Primary current: 0 - 1000A AC Secondary output: 1mV/A AC, 5mV/A or (customized) Secondary current: 0 - 1000mA AC and 0 - 5A AC Max. Cont. Input current: 1200A Load capacity: ≤20Ω , Standard 4Ω Over voltage category: CAT III 600V Output signal: 333mV, 500mV,1V,2V,5V AC at nominal input current Accuracy (1000A Range) 0-10A: ≤0.5% 10-100: ≤0.2% 10-1200A: ≤0.1% Phase Shift(1000A Range) 0-10A: ≤0.5° 10-100: ≤0.2° 100-1200A: ≤0.1° Frequency range: 40Hz-2000Hz or 10-2MHz Dielectric strength: 3KV 50Hz/60Hz at 1 minute Temperature range: -20°C to +55°C Output: 2.5 meter cable with D01 connector Max. voltage not insulated conductors: 600 V Standard: EN 61010-1, EN 61010-2-032, EN 61010-2-031 IEC60044-1, & IEC61869-2, 600V CAT III Installation: Clamp type Output mode: Lead output (2.5m) Connector: BNC, 4mm banana, signal cable(2 cores),customized Mechanical parameters Dimensions (L x W x H) (mm): 102.9 x 219.6 x 28 Weight (g): 550 Holding wire diameter (mm): φ50 Max. jaw opening (mm): 50 Jaw color: Gray or blue Material: PC+ABS+Polycarbonate, UL94 V0

Minimum Order: 3 bushels

The P8 current clamp ct is an affordable & durable mini current clamp ct for measurements to 10A AC. This current clamp ct uses a special magnetic core to provide higher accuracy and lower phase shift. The P8 Series AC current clamp ct is a cheap and economic current clamp probe to be used in power and low level current measurement applications. Electrical parameters Ratio: 2500: 1, 2000:1 or 1000:1 (customized) Accuracy class: 0.2%, 0.5% Phase shift: <10' Primary current: 0 - 10A AC Secondary current: 0 - 10mA AC (customized) Secondary voltage: 0-0.1V AC, 0-0.5V AC, 0-1V AC, 0-5V AC Max. Cont. Input current: 20A Load capacity: ≤10Ω, Standard 4Ω Over voltage category: CAT III 600V Output signal (AC current): From 0 to 10mA AC at nominal input current Output signal (AC voltage): From 0 to 0.5V AC at nominal input current Frequency range: 40Hz-2000Hz Dielectric strength: 3KV 50Hz/60Hz at 1minute Temperature range: -20°C to +55°C Output: 2.5 meter cable with D01 connector Max. voltage not insulated conductors: 720 V Standard: EN 61010-1, EN 61010-2-032, EN 61010-2-031 IEC60044-1, & IEC61869-2, 600V CAT III Installation: clamp type Output mode: lead output(2.5m) Connector: Audio connector, BNC, 4mm banana, signal cable(2 cores) Mechanical parameters Dimensions (L x W x H) (mm): 42× 139 × 20 Weight (g): 180 Holding wire diameter (mm): φ8 Max. jaw opening (mm): 8 Jaw color: Black Material: PC+ABS+Polycarbonate, UL94 V0

Minimum Order: 3 bushels

The S120 current clamp is a high performance AC Clamp on current transformer probe with excellent transformation and low phase shift. The high quality magnetic permalloy core and uniform windings provide for accurate measurements up to 3000AAC/2000AAC/1000AAC/500AAC. The "ring type" jaw permits good magnetic conduction and cable positionings. Provide excellent RMS capabilities and reliable signal reproduction. The S120 clamp on ct is well suited for power quality applications where high accuracy and low phase shift along with wide frequency from 10Hz to 2MHz are important. Measurement range is 100mA to 3000A. The S120 clamp on current transformer is a general purpose 3000A AC Clamp current probe transformer designed for use with DMMs & BNC, cable fault analysis and loggers instruments that have a current input. It has a 1000:1 or 2000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw. The S120 has an integral 2.5m or 5m lead terminated. The rounded jaw design on this clamp probe makes it well-suited for cable fault analysis applications where high accuracy and low phase shift and wide frequency. Electrical parameters Ratio: 1000: 1, 2000:5 or 3000:5(customized) Accuracy class: 0.1%, 0.2%, 0.5% Primary current: 0 - 3000A AC Secondary current: 0-1A or 0 - 5A AC (customized) Secondary voltage: 0-2V , 0-5V AC (customized) Max. Cont. Input current: 3600A Load capacity: ≤20Ω, standard 4Ω Over voltage category: CAT III 600V Output signal (AC current): 500mA, 1A,2A,5A AC at nominal input current Output signal (AC voltage): 1V, 2V, 5V, 10V AC at nominal input current Frequency range: 10Hz-2MHz Dielectric strength: 3KV 50Hz/60Hz at 1 minute Temperature range: -40°C to +55°C Output: 2.5 meter cable with D01 connector or BNC Max. voltage not insulated conductors: 600 V Standard: EN 61010-1, EN 61010-2-032, EN 61010-2-031 IEC60044-1, & IEC61869-2, 600V CAT III Installation: clamp type Output mode: lead output(2.5m, 5m or 10m) Connector: BNC, 4mm banana, signal cable(2 cores),customized Range version: 100A, 200A, 400A, 500A, 1000A, 2000A, 3000A Accuracy (3000A Range) 0-10A: ≤0.5% 10-100: ≤0.2% 100-3000A: ≤0.1% Phase Shift(3000A Range) 0-10A: ≤0.5° 10-100: ≤0.2° 100-3000A: ≤0.1° Mechanical parameters Dimensions (L x W x H) (mm): 178 x 290 x 30 Weight (g): 1200 Holding wire diameter (mm): φ120 Max. jaw opening (mm): 120 Jaw color: Red & Grey Material: PC+ABS, UL94 V0

Minimum Order: 3 bushels

The Model D20 AC/DC current clamp is a portable 100A/200Arms current probe with insulated BNC output cable that can accurately measure AC or DC current waveforms. The unit has proportional mV output for direct readings on oscilloscopes from DC to 1MHz at -3dB. The D20 is power by a rechargeable multimeter battery or from a 9 V power signal cable. It is the perfect tool for most of the oscilloscopes. The D20 current clamp is a general purpose 200A AC/DC current probe designed for use with DMMs, oscilloscopes, power loggers and energy meter calibration instruments that have a current input. It has a 1000:1 ratio and output of 10mV per amp measured in the jaw. The D20 current probe has an integral 2.5m lead terminated. The rounded jaw design on this current clamp makes it well-suited for power applications where high linearity 0.1% and low phase shift and wide frequency response up to 200kHz are important. Electrical parameters Ratio: 1000: 1 or 2000:1 (customized) Accuracy class: 0.2%, 0.5%, 1%, 2% Primary current: 0 - 100A or 0-200A AC/DC Signal output: 10mV/A or 1mV/A Secondary voltage: 0 - 1V or 0 - 2V AC/DC Max. Cont. Input current: 200A AC/DC Load capacity: ≤20Ω , Standard 4Ω Over voltage category: CAT III 600V Linearity: 0.1% Frequency range: 10Hz-1MHz Frequency response time: ≤10us Phase Shift at 50/60Hz: ±1° Dielectric strength: 3KV 50Hz/60Hz at 1minute Temperature range: -40°C to +55°C Output: 2.5 meter cable with D01 or BNC connector, 4mm banana Max. voltage not insulated conductors: 720 V Power supply: 5V or 9V DC Standard: EN 61010-1, EN 61010-2-032, EN 61010-2-031 IEC60044-1, & IEC61869-2, 600V CAT III Installation: clamp type Output mode: lead output(2.5m) Pollution Degree: 2 Protection: IP40 Connector: BNC, 4mm banana, signal cable(4 cores),customized Mechanical parameters Dimensions (L x W x H) (mm): 53 x 138 x 28 Weight (g): 420 Holding wire diameter (mm): φ20 Max. jaw opening (mm): 20 Jaw color: Red, black Material: PC+ABS, UL94 V0

Minimum Order: 3 bushels

The round jaw design on the D50 series hall effect current clamp along with the high content permalloy core makes them well suited for power quality applications where high linearity and low phase shift along with wide frequency are important from 10Hz to 200kHz. Measurement range is 0 to 500A or 0 to 1000A AC/DC. It designed for oscilloscopes, power quality analyzer, waveform displaying instruments, and other frequency sensitive displaying instruments with BNC inputs. The Model D50 AC/DC hall effect current clamp is a portable 500A/1000Arms current probe with insulated BNC output cable that can accurately measure AC or DC current waveforms. The unit has proportional 1V or 2V output for direct readings on oscilloscopes from DC to 1MHz at -3dB. The D50 is power by a rechargeable multimeter battery or from a 5V or 9 V DC power signal cable. It is the perfect tool for most of the waveform displaying instruments. Electrical parameters Ratio: 1000: 1 , 2000:1 (customized) Accuracy class: 0.2%, 0.5%, 1%, 2% Primary current: 0 - 500A or 0-1000A AC/DC Signal output: 1mV/A, 10mV/A Secondary voltage: 0 - 1V or 0 - 2V AC/DC Max. Cont. Input current: 1200A AC/DC Load capacity: ≤20Ω, standard 4Ω Over voltage category: CAT III 600V Linearity: 0.1% Frequency range: 10Hz-1MHz Frequency response time: ≤10us Phase Shift at 50/60Hz: ±1° Dielectric strength: 3KV 50Hz/60Hz at 1minute Temperature range: -40°C to +55°C Output: 2.5 meter cable with D01 or BNC connector Max. voltage not insulated conductors: 720 V Power supply: 5V or 9V DC Standard: EN 61010-1, EN 61010-2-032, EN 61010-2-031 IEC60044-1, & IEC61869-2, 600V CAT III Installation: clamp type Range: 10A, 100A, 1000A optional Output mode: lead output(2.5m) Pollution Degree: 2 Protection: IP40 Connector: BNC, 4mm banana, signal cable(4 cores),customized Mechanical parameters Dimensions (L x W x H) (mm): 105 x 218 x 30 Weight (g): 650 Holding wire diameter (mm): φ52 Max. jaw opening (mm): 52 Jaw color: Red & Grey Material: PC+ABS, UL94 V0

Minimum Order: 3 bushels

The round jaw design on the S50 Series AC current clamp on CT along with the high content permalloy core makes them well suited for power quality applications where high accuracy and low phase shift along with wide frequency are important from 10Hz to 10MHz. Measurement range is 1mA to 1200A. The S50 clamp on ct is a general purpose 1200A AC current clamp designed for use with DMMs & BNC, power loggers and energy meter calibration instruments that have a current input. It has a 1000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw. The S50 clamp on CT has an integral 2.5m lead terminated. The rounded jaw design on this current clamp makes it well-suited for power applications where high accuracy 0.1% and low phase shift and wide frequency response are important. Electrical parameters Ratio: 1000: 1 , 2000:1, 1000:5 (customized) Accuracy class: 0.1%, 0.2%, 0.5% Primary current: 0 - 500A AC and 0-1000A AC Signal output: 1mV/A, 1mA/A Secondary voltage: 0 - 0.5V AC and 0 - 1V AC; Secondary current: 0-1A or 0-5A AC Max. Cont. Input current: 1200A Load capacity: ≤20Ω, standard 4Ω Over voltage category: CAT III 600V Frequency range: 10Hz-10MHz Dielectric strength: 3KV 50Hz/60Hz at 1minute Temperature range: -40°C to +55°C Output: 2.5 meter cable with D01 or BNC connector Max. voltage not insulated conductors: 600 V Standard: EN 61010-1, EN 61010-2-032, EN 61010-2-031 IEC60044-1, & IEC61869-2, 600V CAT III Installation: clamp type Range: 10A, 100A, 1000A optional Output mode: lead output(2.5m) Connector: BNC, 4mm banana, signal cable(2 cores),customized Accuracy (1000A Range) 0-10A: ≤0.5% 10-100: ≤0.2% 10-1200A: ≤0.1% Phase Shift(1000A Range) 0-10A: ≤0.5° 10-100: ≤0.2° 10-1200A: ≤0.1° Mechanical parameters Dimensions (L x W x H) (mm): 105 x 218 x 30 Weight (g): 650 Holding wire diameter (mm): φ52 Max. jaw opening (mm): 52 Jaw color: Red & Grey Material: PC+ABS, UL94 V0

Minimum Order: 3 bushels

The round jaw design on the P18 Series double ratio AC current clamp along with the high content permalloy core makes them well suited for power quality applications where high accuracy and low phase shift along with wide frequency are important. Measurement range is 1mA to 200A. The P18 AC current clamp is a general purpose 200A AC current clamp ct designed for use with DMMs, power loggers and energy meter calibration instruments that have a current input. It has a 1000:1 ratio and output of 1mA per amp or 1mV per amp measured in the jaw. The P18 clamp ct has an integral 2.5m lead terminated. The rounded jaw design on this current clamp makes it well-suited for power applications where high accuracy 0.1% and low phase shift and wide frequency response are important. FEATURES ■ UL, CE mark; ■ Holding wire diameter: φ18mm; ■ Frequency 10Hz-2MHz Bandwidth; ■ High times harmonic measurement; ■ Conforms to EN 61010, 600V CAT III; ■ Measurement range of 1mA to 200A AC; ■ Low phase shift for power measurement; ■ High content nickel metal permalloy core; ■ Improved ergonomic design & easy operation; ■ High precision 0.1% for current measurement; ■ Designed for DMMs, recorders, loggers, oscilloscopes, power and harmonic meters; Electrical parameters Ratio: 1000: 1 or 2000:1 (customized) Accuracy class: 0.1%, 0.2% Primary current: 0 - 10A AC and 0-200A AC Signal output: 10A (100mV/A) and 100A (200A)(10mV/A) with Switch Secondary voltage: 0 - 1V AC, 0 - 2V AC, 0 - 5V AC, 0 - 10V AC Secondary current: 0 - 100mA AC and 0 - 200mA AC Max. Cont. Input current: 240A Load capacity: ≤20Ω , Standard 4Ω Over voltage category: CAT III 600V Frequency range: 10Hz-2MHz Dielectric strength: 3KV 50Hz/60Hz at 1minute Temperature range: -40°C to +55°C Output: 2.5 meter cable with D01 or BNC connector, 4mm banana Max. voltage not insulated conductors: 600 V Ratio: single winding, or double winding Standard: EN 61010-1, EN 61010-2-032, EN 61010-2-031 IEC60044-1, & IEC61869-2, 600V CAT III Installation: clamp type Output mode: lead output(2.5m) Connector: BNC, 4mm banana, signal cable(2 cores),customized Mechanical parameters Dimensions (L x W x H) (mm): 52.5 x 137.5 x 28 Weight (g): 400 Holding wire diameter (mm): φ18 Max. jaw opening (mm): 18 Jaw color: Red, black Material: PC+ABS, UL94 V0 APPLICATION ■ Multimeter; ■ Power meter; ■ Phase angle meter; ■ Energy sub-meters; ■ Power load monitoring; ■ Data logging/recording; ■ Energy meter calibrator; ■ power and harmonic meters; ■ Power quality analyzer(PQA); ■ Measuring around cable bundles; ■ Waveform analysis(oscilloscopes meter);

Minimum Order: 3 bushels

The FQ-RCTA02 rogowski coil flexible current sensor is designed for easy installed in tight spaces and without the need for dismantling the primary busbar or cables. It includes a flexible Rogowski coil probe and electronic modules. The signal from the coil probe can be amplified by the electronic amplifier modules through the integration processing. The output signal can be directly used in oscilloscope, digital multimeter or data logger recording instrument. good linearity, easy to use, measuring large current, 6000A/3V, 600A/3V, 60A/3V or 3000A/3V, 300A/3V, 30A/3V, lower phase shift. In particular, it can be installed in tight spaces, around cable bundles, around wide or large bus bars, or even wrapped around irregular shapes. Models range from 1 to 100,000Arms with an accuracy of 1% of reading. Rated EN 61010, 600V CAT IV, 1000V CAT III. This feature facilitates positioning the sensor around the conductor, enhances user safety, and alleviates the drooping effect associated with other flexible sensors. FEATURES  CE, UL, CNAS mark; With harmonic measurement; Frequency 0.1Hz-2MHz Bandwidth; Conforms to EN 61010, 1000V CAT III; Measurement range of 1A to 6000A AC; Low phase shift for power measurement; High permeability magnetic material core; Excellent linearity 0.2% for current measurement; Multi-size are available  GENERAL DATA  Ambient operating temperature: -30~+80°C  Ambient storage temperature: -40~+90°C  Standards safety：EN 61010-1, EN 61010-2-032, EN 61010-2-031, IEC60044-1, & IEC61869-2, 1000V CAT III Output terminals: 0.5m cable with Safety BNC plug APPLICATIONS  Multimeter; Power meter; Phase angle meter; Energy sub-meters; Power load monitoring; Data logging/recording; Energy meter calibrator; Power and harmonic meters; Power quality analyzer(PQA); Measuring around cable bundles; Waveform analysis(oscilloscopes meter);

Minimum Order: 3 bushels

The FQ-RCT02 flexible current sensor is an AC current sensor composed of a flexible Rogowski coil. The flexible current sensor permits measurements on conductors where standard clamp-on probes cannot be used. In particular, it can be installed in tight spaces, around cable bundles, around wide or large bus bars, or even wrapped around irregular shapes. It is suitable for large current measuring. They combine the benefits of a thin, flexible, clip-around Rogowski (sense) coil with a signal conditioner providing accurate, true rms measurement, of voltage output 100mV/kA. Models range from 1A to 100,000Arms with an accuracy of 1% of reading. Rated EN 61010, 600V CAT IV, 1000V CAT III. Low cost AC current measurement probe designed to plug into digital multimeters, oscilloscopes, power quality analysis and power or harmonic meters. The length of the flexible current sensor can be selected from 40cm to 100cm. Fits around large or small conductors. Capable of getting into tight or difficult spaces. Ideal for measuring AC current in a group of conductors. FEATURES  Flexible and light weights  Easy & quick installation in tight spaces  No danger from open-circuited secondary  No core saturation or damage if overloaded  Excellent linearity 0.2% for current measurement; Multi-size are available  GENERAL DATA  Ambient operating temperature: -30~+80°C  Ambient storage temperature: -40~+90°C  Standards safety：EN 61010-1, EN 61010-2-032, EN 61010-2-031, IEC60044-1, & IEC61869-2, 1000V CAT III APPLICATIONS  Power quality monitoring  Power meters  Smart logger  Energy sub-meters  Distributed measurement systems DMMs, oscilloscopes

Minimum Order: 3 bushels

The GF302D1S portable three phase energy meter test system consists of an integrated 0.05% three-phase current and voltage source and a three-phase electronic reference standard meter of accuracy class 0.02. Characteristic features of the GF302D1S are its wide measuring range from 0 to 120A and 0 to 600V, high accuracy and high tolerance to unwanted external influences. The GF302D1S allows the monitoring of meter installations as well as analysis of the local mains conditions when it is as portable reference working standard. The equipment offers high functionality combined with an excellent menu guided operation via built-in keyboards and colored 7' touch LCD-display. Voltage & current harmonics output from 2 to 63 times. This model portable meter test system can be programmable by PC, automatic generation of energy meter error test report. Specification Customized support: OBM Place of Origin: Beijing, China Brand Name: GFuve Model Number: GF302D1S Accuracy: 0.02%, 0.05% Power supply: One Phase AC 100-265V, frequency 50/60Hz. Voltage and Current Measuring range: 0-600V/1mA-120A Voltage error: ±0.02% (30V-600V) ±0.05% (0.1V-30V) Voltage and Current output range: 500V/120A Active power output accuracy: 0.05%RG Reactive power output accuracy: 0.1%RG Active power output stability: <0.01%RG/120s Reactive power output stability: <0.02%RG/120s Weight: 23 kg

Minimum Order: 1 bags

GF313V2 onsite portable three phase electronic meter test set is the newest product produced by our company by widely visiting users and referring to the advantages of the same kind of products home and abroad. The measured part of the product adopts high speed A/D transmission to send DSP to conduct digital processing, which largely improves measured degree of accuracy and stability. Central processing part adopts 32-bit ARM embedded technology to make instrument interface novel, function abundant, operation distinct and easy, and performance steady. Class of accuracy: Class 0.1, 0.2 or 0.5, range from 3×120A/3×600V or 3×200A/3×600V, with comfort design, small size and light weight. The model GF313V2 three phase meter meter test set is suit for metrological service of electricity power utilities, industrial and mining enterprises and electric lab to field use. Specification Customized support: OBM Place of Origin: Beijing, China Brand Name: GFuve Model Number: GF313V2 Accuracy: 0.1%, 0.2%, 0.5% Power supply: External power ;Phase voltage supply; Li-Battery supply Voltage range: 0-600V Voltage error: ±0.1%(30-600V); ±0.05%(30-600V) Active energy error: ±0.1%, ±0.2%, ±0.5% Reactive energy error: ±0.2% , ±0.5% Stability: 0.02%/minute Long term Stability: <100x 10E -6 /Year Dimension: 245x168x70 mm Weight: 1.8 kg

Minimum Order: 1 bags

GF312V2S portable three phase reference meter on-site is the newest product produced by our company by widely visiting users and referring to the advantages of the same kind of products home and abroad. The measured part of the product adopts high speed 24bit A/D transmission to send DSP to conduct digital processing, unique power compensation algorithm with patented technology, which largely improves measured degree of accuracy and stability. Central processing part adopts 32-bit ARM embedded technology to make instrument interface novel, function abundant, operation distinct and easy, and performance steady. Class of accuracy: Class 0.02 or 0.05, range from 3×12A/3×600V or 3×120A/3×600V, with comfort portable design and light weight. The model GF312V2S portable reference meter is suit for electricity power utilities metrogical departments, Industrial and mining enterprises departments and electric lab to field use. Specification Customized support: OEM, ODM, OBM, Software reengineering Place of Origin: Beijing, China Brand Name: GFuve Model Number: GF312V2S Accuracy: 0.02%, 0.05%, 0.1% Power supply: External power ;Phase voltage supply; Li-Battery supply Voltage range: 0-600V Voltage error: ±0.05%; ±0.02% Current measurement range: 1mA-12A or 1mA-120A(direct connection Active energy error: ±0.05% or ±0.02% Reactive energy error: ±0.1% or ±0.05% Active energy error (CT): ±0.1% (1mA-120A) Reactive energy error (CT): ±0.2% (5mA-120A) Weight: 4.5 kg

Minimum Order: 1 bags

The model GF313 handheld three phase electricity meter field tester is a economical 0.2% AC energy meter accuracy testing device, mainly used to test three phase and single phase electricity energy meter error on site, measure all various of AC electrical parameters - U, I, P, Q, S, PF, F and CT ratio & phase error etc. And then it can check whether the wiring of the electricity meter is correct. GF313 electronic meter tester is an ideal electrical test tool for the metrological service of electricity power utilities. It has been widely used in more than 80 countries around the world. Specification Customized support: OBM Place of Origin: Beijing, China Brand Name: GFuve Model Number: GF313 Accuracy: 0.2%, 0.5% Power supply: 220V; Li-polymer battery; Power line supply Voltage range: 0-600V(0-830V) Voltage error: ±0.05% (30V-600V) ±0.1% (0.01V-30V) Current Test range: 1mA-120A; 0-200A; 0-500A; 0-1000A; 0-2000A; 0-3000A Energy constant: 180000imp/kWh, 1800imp/kWh, 180imp/kWh Pulse ratio: 1:1 Pulse Output level: 5V Pulse frequency: Standard 400Hz-2.5KHz, customized max 10KHz Weight: 1.6 kg

Minimum Order: 1 bags

GF112V2 made in GFUVE GROUP, is a high precision single phase handheld energy meter accuracy tester in class 0.1, used for testing all kinds of single phase electronic meters error on site. Wide measurement range from 1mA to 200A and 0 to 600V, frequency range 40.000Hz to 70.000Hz, and also can be used to test alternating current electrical parameters - voltage, current, active power, reactive power, apparent power, harmonics, phase angle, power factor, frequency, energy etc. It can display U & I wave form and vector diagram. Small size, light weight, simple and convenient operation. It is an ideal testing equipment for the metrology departments of electricity power companies and electrical service engineers. Specification Customized support: OEM, ODM, OBM, Software reengineering Place of Origin: Beijing, China Brand Name: GFuve Model Number: GF112V2 Accuracy class: 0.1% Power supply: AAA type, Li rechargeable battery, 2700mAh, 3.6V warm-up: <2 min Voltage and current range: 600V/1000A Clamp on cts diameter: 8mm, 13mm, 18mm, 20mm, 30mm, 50mm, 120mm optional Pulse input level: 5V Data storage: 5000 sets Communication port: USB & Bluetooth port Isolation protection: IEC 61010-1:2001 Measurement Category: 600V CAT III Degree of protection: IP54 Display: 3.5 inch touch TFT color LCD

Minimum Order: 1 bags