Telecom Equipment & Accessories

FTTH Jumper Cable for Network SM Duplex Single Mode LC to LC Fiber Patch Cord is used as a jumper from the equipment to the optical fiber wiring link. It has a thick protective layer, which is generally used for the connection between optical transceiver and terminal box. It is applied in some fields such as optical fiber communication system, optical fiber access network, optical fiber data transmission and LAN. There are many kinds of optical fiber jumpers (also known as optical fiber connectors), that is, optical fiber connectors connected to optical modules, and they cannot be used with each other. SFP module is connected to LC optical fiber connector, while GBIC is connected to SC optical fiber connector. LC type optical fiber jumper: connector connecting SFP module, which is made of modular jack (RJ) latch mechanism with convenient operation. LC-LC Fiber Optic Cable body is made of PVC/ LSZH plastic materials, which is shiny, tough, environmental protection, not fade,not broken and not easily deformed. The inside optical cable is aramid, which is tough, tensile, non-toxic, fire retardant, core protection and low smoke. The connector is PBT plastic materials and fine copper, which is firm, durable, environmentalprotection, high temperature resistant, not fade, not broken and not easily deformed. 3.Application 1. Communication rooms 2. FTTH (Fiber to The Home) 3. LAN (Local Area Network) 4. FOS (fiber optic sensor) 5. Fiber Optic Communication System 6. Optical fiber connected and transmitted equipment

Minimum Order: 500

Focus Infra’s Optical Fiber SM SX SC APC with Flange Fiber Optic Coupler is used for Single Mode Fiber Connection. The "SC" connector is a standard square connector, using engineering plastics, which has the advantages of high temperature resistance and not easy to oxidize. The optical interface on the transmission equipment side generally uses an SC connector. The Fiber Optic Coupler is a device for detachable (movable) connection between an optical fiber and an optical fiber. SC type is an optical fiber connector developed by NTT Corporation of Japan. Its shell is rectangular, and the structural dimensions of the pins and coupling sleeves used are exactly the same as those of the FC type. Among them, the end face of the pin mostly adopts the PC or APC type grinding method; the fastening method is the plug-in latch type, without rotation. This type of connector is cheap, easy to plug and unplug, small fluctuations in insertion loss, high compressive strength, and high installation density. Features: - Convenience and ease of handling - Flange or threaded mounting type - Ceramic/Zirconia or phosphorous bronze sleeves - Good changeability and repeatability - Compatible with fiber panels - Low insertion and return loss and back reflection - High precision alignment and High precision sleeve - Compact design - High reliability and stability - Fast and easy connection - Lightweight and durable plastic body

Minimum Order: 5000

A Fiber Optic Splice Sleeve is consisted of cross linked polyolefin, hot melt tubes and stainless reinforcing steel rod which keep optic transmission properties of optical fiber and enhance the protection to optical fiber splices. It is friendly operated to the optic fiber during installation without damaged and micro bending. The Fiber Optic Splice Sleeve intends to protect (mechanically) fiber optic splices. The Fiber Optic Splice Sleeve is built from shrinkable plastic tube with metal cylinder inside. The fibers are inserted before splicing into the plastic tube. After making the splice, the shrinkable tube is heated and shrunk on the splice. It can protect the spliced fiber from being break down and unwanted bending and is coated with the plastic tube. It gives to the installer flexibility while using the spliced fibers during installation. The Fiber Optic Splice Sleeve is commonly known as an optical fiber heat shrink protect sleeve. It is a protective optical fiber splicing component composed of a special cross-linked polyolefin and a hot melt tube. Features: 1. Not affect the optical conductivity of the spliced fiber 2. Easy operation, reduce the damage of optical fiber duringl installation 3. Strong practicality 4. Transparent casing 5. Quickly shrink, improving work efficiency 6. extend the service life of the fiber 7. No air bubbles, no fiber breakage

Minimum Order: 5000

PRODUCT DESCRIPTION FTTH Normal Fiber Optic Patch CordMultimode Duplex Om3om4 LC Sc FC St Fiber Optic Patch Cord Product Description Product Parameters Technical parameters Characteristic Item Test condition Single mode fiber Multimode Fiber Optical property Insertion Loss (dB) UPC LED <0.2dB <0.4dB APC <0.3dB <0.4dB Return Loss (dB) UPC LD >55dB >25dB APC >65dB - Mechanical test Impulse test 1.8 height, 8 times <0.1dB <0.1dB Vibration test 10-60Hz, 1mm full amplitude <0.1dB <0.1dB Plug service life Above 1000times <0.1dB <0.1dB Tensile strength >50N <0.1dB <0.1dB Environmental property High temperature test +85ºC, 96hs <0.2dB <0.2dB Cryogenic test -40oC,96hs <0.2dB <0.2dB Damp heat test +40°C,90-95%RH,96hs <0.2dB <0.2dB Ordering information Cable outer diameter Ψ0.9mm,Ψ1.6mm,Ψ2.0mm,Ψ3.0mm or customer specified Cable length 1m,3m,5m,15m,25m,30m or customer specified Fiber type B1.3=G652D, B6A1=G657A1, B6A2=G657A2, A1=50/125, A1b=62.5/125, OM3=Maxband*150, OM3=Maxband*300, OM4=Maxband*550, OM5=Maxband*550 Fiber count Simplex, Duplex Outer jacket material PVC,LSZH Outer jacket color Refer to Chromatogram Connector A side Connector type LC, SC,ST, FC Ferrule type UPC, APC Connector B side Connector type LC, SQ,ST,FC Ferrule type UPC, APC Marking&package Per customer's request or factory standard

The cable consists of individually color-coded 900µm secondary coated fibers reinforced with aramid yarns and covered with UV and flame-resistant LSZH Sheath. The cable cross-section is Fig 8 made with a steel wire strength member Product Construction Fiber: 1-12fibers 900µm tight buffer Strength Member: Aramid yarn Messenger Member: Steel wire or non-metallic member. Outer Jacket: UV and Flame resistant LSZH FiberType: G.652D, G.657A1 or G.657A2 single mode fiber Features Good UV and flame resistant. Compact, soft, flexible, and easy to install. Fig8 self-supporting design. Applications Used in the access network or access cable from outdoor to indoor in customer premises network. Used as access building cable in the premises distribution system, mainly used in indoor outdoor aerial access cabling. XUANFENG TECHNOLOGY CO., LTD. is a modern enterprise for primary operating and selling electronic wires and electric cables. We have the trading company and production factory both possessing of the convenient transportation and ripe producing experiences.We have the CPR, FCC, ISO, CE, ROHS, ccc,and ISo9001:2008 and can provide the products according to ASTM, ICEA, BS, DIN, IEC, GB etc. standard to meet the customers’ various requirements. We produce electrical cables and communication cables. We specialize in supplying 300V/500V solid/stranded general PVC cable, coaxial cable, security cable, telephone cable, speaker cable, alarm cable,networking cable, H05RN-F/H07RN-F flexible rubber cable, YH/YHF welding cable, submersible pump cable, aluminium conductor cable, copper/aluminium high-middle-low voltage PVC/XLPE cable ,solar cable and patch cord, usb cable,hdmi cbale,audio cable,vga cable,and other products. Up to now, we have established the solid foundation of several important markets such as Mid East, Europe, Africa, Latin America, Southeast Asia, North America market. We have won a good reputation among customers with good quality, competitive prices and advanced techniques since our establishment. WIth a positive innovation and hard work，all staff will struggle for making XUANFENG to be afamous brand in the world and hand in hand with you to create a rosy prospect.

Minimum Order: 100

Main technical parameters : * Optical fibe , r external diameter: φ0.9mm, φ2.0mm, φ3.0m , m are option al, and PC, UPC, and APC a , re available, there are two kinds of sing le-mode and multi-mode. * Insertion loss: ,  ≤0.2dB * Echo Loss: PC≥40dB,UPC≥50dB , ,APC≥60dB * Exchangeability test: ≤0.2dB , * Vibration test: ≤0.1dB (10-60Hz, 1.5m , m amplitude) * Tensile strength test: ≤0 , .1dB (0- 15Hg tension, excluding 0.9mm opt , ical fiber) * High-temperature test: ≤0.2 , dB (+85 C, lasting 100 hours) * Low-tempe , rature test: ≤0.2dB (-40 C, lasting 100 h , ours) * Temperature cycling test:≤0.2dB ( , -40 ~85 C, after 5 cycles) * Humidity te , st: ≤0.2dB (+25℃~+65℃, relative humidity ,  93%, 100 hours  later) * Commonly use , d connectors: SC (large head)/LC (small head , /FC (spiral  port)/ST (card port) Scope

Minimum Order: 100

1.Fiber optic patch cord is available in both singlemode and multimode versions. 2.Both singlemode and multimode versions fiber optic patch cord come with a zirconia ceramic ferrule with pre-polished PC,UPC,APC profile and convex spherical end. 3.These end face types allow for faster polishing, and low back reflection and optical loss, while ensuring maximum repeatability

PRODUCT DESCRIPTION High quality cat5e utp BC/CCA lancable product description Name Lan Cable CAT5E UTP Conductor Material CCA Conductor Diameter 0.48 Conductor Insulation HDPE Jacket PVC,LSOH,FR-PVC,LSZH Certificates ISO,UL,ETL,CE,ROHS Length 305M Brand Lansan,OEM,ODM Lead Time Less than 500 boxes----within 10 days 500-2500 boxes----within 15 days 2500-20000 boxes----within 20 days (Lead time is negotiable when customer has special requirements.) product show BC CCA Condoctor Cat5e Lan Cable 0BC CCA Condoctor Cat5e Lan Cable 1 FAQ BC CCA Condoctor Cat5e Lan Cable 2

16 Port Outdoor Fiber Distribution Box Black Outdoor optical distribution Frame Description: Fiber optic terminal box is available for the distribution and terminal connection for various kinds of optical fiber system, especially suitable for mini-network terminal distribution, in which the optical cables, patch cores or pigtails are connected. Features: The box is made of ABS, and lifetime is more than 20 years. It also can be used under -30°c. Bi-layer structure design. The upper layer is for optical splitter, the other layer is for fiber splicing. Easy to operate. Usually installed as wall mounted in the building or at the green belt. It can accommodate 16 pcs SC Simplex or LC Duplex dapters. It can be designed to client requirements. It meets YD/T988-2007 standards. Application: FTTH access network CATV Networks Telecommunication Networks Data communications Networks Operation conditions: Temperatures:-40℃ — 60℃ Humidity:93% at 40℃ Air Pressure:62kPa – 101kPa

12VDC 10G Base-T to 10G Jumbo Frame SFP+ RJ45 to Fiber Ethernet Media Converter Model: LNK-10G-MC Series Overview E-link 10G Base-T to 10G Base-R Media Converter supports two types media for network connection such as 10GBase-T and 10GBase-FX. The bridge media converter is designed with a 10Gbase Ethernet PHY chip that connects two types segments operation smoothly. This converter can be used as standalone unit or as slide-in module to the 19" converter rack Chassis for use at a central wiring closet. Features Support Jumbo Frame Transparent Transport and very low delay Support DMI function for SFP+ fiber module Support Loopback test function Support hot plugging Full State Led display Easy installation Provide reliable long-distance connection Fast connection with multi-function Small portable size case Plug and play Application Connection between fiber to copper 10Gbps Ethernet equipment function as fiber-to- copper media converter for long distance transmission up to 120km Extend the network distance between two 10 Gigabit Fiber Switches across a fiber link up to 80km in length Convert your 10G SFP+ Direct Attach to multimode or single mode fiber. Technical Indexes Standards 1000Base-T, 2.5GBase-T, 5Gbase-T, 10Gbase-T 1000Base-X, 2500Base-X, 5GBase-R , 10GBase-R Media Supported 1000Base-T: Cat5 UTP/STP. MAX 100m; 2.5GBase-T: Cat5e UTP/STP. MAX 50m; 5GBase-T: Cat5e UTP/STP. MAX 50m; 10G Base-T: Cat6a UTP/STP. MAX 50m; Port Type RJ45, SFP Slot Work Mode 1000Base-T to 1000Base-X 2.5GBase-T to 2500Base-X 5Gbase-T to 5GBase-R 10Gbase-T to 10GBase-R Power Supply 12V DC Power consumption MAX 5W Operation Temperature 0℃ to 55℃ Relative Humidity 5% to 80% (non-condensation) Ordering Information Model Description LNK-MC10G-SFP+ 10G Base-T to 10G Base-R Media Converter, SFP+ Ports, not including SFP+ Modules

TX-2.5G/RX-1.25G GPON Transceiver Class B+ (SMF, 1490nm-TX/1310nm-RX, 20km, SC ) Description The GIGAOPTO's GTS-SGT21-20DCB is a high performance transceiver module for single fiber communications using a 1490nm continuous-mode transmitter and a 1310nm burst-mode receiver. It is designed to meet ITU G.984.2 Class B+ requirements for optical line terminal (OLT) applications. The 1490nm DFB LD transmitter has automatic power control (APC) function and temperature compensation circuitry to ensure stable optical power and extinction ratio over all operating temperature range. The transmitter meets Class 1 eye safety per IEC60825 and CDRH standards.The receiver has a hermetically packaged APD-TIA (trans-impedance amplifier) pre-amplifier and a limiting amplifier with LVPECL compatible differential outputs. It features a Burst Packet Detect (SD) output which is LVTTL compatible. The SD output will come high after receiving the burst packet. The module provides digital diagnostic information of its operating conditions and status, including transmitting power, laser bias current, module temperature, and supply voltage. Calibration and alarm/warning threshold data are written and stored in the internal memory (EEPROM). SFP transceiver module has done sampling test under most famous brands of routers, switches, servers. The hot swappable GPON SFP transceiver is ideal for Internet Service Provider (ISP) Gigabit Passive Optical Network (GPON) communication links, other optical links. Specification Form Factor GPON SFP Power Supply Voltage 3.3V Connector/Polish SC/UPC Maxim Distance 20km DDM Supported Media SMF Warranty 3 Years Temperature Commercial /Industrial TX Data Rate 2.488Gbps RX Data Rate 1.244Gbps TX Wavelength 1490nm RX Wavelength 1310nm Power Consumption <1.5W Total Current 450mA Transmitter Type DFB Receiver Type APD TX Optical Power +1.5~+5.0dBm RX Sensitivity < -28.0dBm Extinction Ratio >8.2dB Receiver Overload >-8dBm Protocols SFF-8472, ITUT-984.2 Features Single fiber bi-directional data links asymmetric TX 2488Mbps/RX1244Mbps application 1490nm continuous-mode DFB laser transmitter and 1310nm burst-mode APD-TIA receiver Small Form Factor Pluggable package with SC/UPC Connector 0 to 70°C operating temperature Single 3.3V power supply Digital diagnostic monitoring interface Digital burst RSSI function to monitor the input optical power level LVPECL compatible data input/output interface LVTTL transmitter disable control LVTTL transmitter laser fault alarm Fast LVTTL receiver Signal Detect (SD) indication response Low EMI and excellent ESD protection Class I laser safety standard IEC-60825 compliant RoHS6 Compliance Application Gigabit-capable Passive Optical Networks (GPON) Standards Complies with SFP Multi-Source Agreement (MSA) SFF-8074i Complies with ITU-T G.984.2 Amendment 1 Complies with FCC 47 CFR Part 15, Class B Complies with FDA 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50, dated June 24, 2007 Complies with SFF-8472 Compatible with TR-NWT-000870 4.1 ESD sensitivity classification Class2. Compatible with Telcordia GR-468-CORE Ordering information - Gigaopto’s GPON OLT SFP Series(DFB+APD SC Simplex) P/N Date Rate (Gb/s) Wavelength (nm) Class Tx Power Rx Sensitivity Temperature GTS-SGT21-20DCB TX-2.488/RX-1.244 TX-1490nm/RX-1310nm B+ +1.5~+5.0dBm < -28.0dBm Com GTS-SGT21-20DIB TX-2.488/RX-1.244 TX-1490nm/RX-1310nm B+ +1.5~+5.0dBm < -28.0dBm Ind. GTS-SGT21-20DCC TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C+ +3.0~+7.0dBm < -30.0dBm Com GTS-SGT21-20DIC TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C+ +3.0~+7.0dBm < -30.0dBm Ind. GTS-SGT21-20DCD TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C++ +4.5~+10.0dBm < -31.0dBm Com GTS-SGT21-20DID TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C++ +4.5~+10.0dBm < -31.0dBm Ind. GTS-SGT21-20DCE TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C+++ / D +6.0~+10.0dBm < -32.0dBm Com GTS-SGT21-20DIE TX-2.488/RX-1.244 TX-1490nm/RX-1310nm C+++ / D +6.0~+10.0dBm < -32.0dBm Ind. Note OEM/ODM Supported, Please Feel Free To Contact Us! Compatibility All of GIGAOPTO's GTS-SGT21-20DCB SFP optical transceiver modules are open sourced, can be coded to be fully compatible with worldwide popular brands' devices, e.g. HUAWEI MA5603T, HUAWEI MA5608T, HUAWEI MA5680T, HUAWEI MA5800T, ZTE ZXA10 C300, ZTE ZXA10 C320, ZTE C600, Alcatel-Lucent 7360, Nokia 7360, C- DATA, VSOL, BDCOM. Please refer to the following table for detailed compatibility, please feel free to contact us. Corresponding Compatible Brand/Part Number Brand Part Number Brand Part Number Gigaopto GTS-SGT21-20DCB Alcatel-Lucent 3FE53441AA 01 HuaWei GPON-OLT-CLASS B+ Nokia 3FE53441ACAA ZTE GPON-OLT-Class B+ Calix 100-01782 ZTE 33030100152 Dasan MXK-GPON-SFP-B+-RSSI Ubiquiti UF-GP-B+ Cisco SFP-GPON-B BDCOM OLT-GSFP-B+ Calix 100-01836 Broadex D24364-SSCB SuperXon SOGP4321-PSGB WTD RTXM167-522

Product Description C Band 75/100GHz 400G Coherent Module QSFP-DD ZR 80~120KM for DCI Applications This product is a coherent module, compliant with the OIF 400ZR MSA and QSFP-DD MSA standards, is designed for DCI applications. The digital diagnostics function is available via an I2C interface, as specified by the QSFP-DD MSA. The product is a C-band 75G/100 GHz grid coherent optical module that combines coherent DSP ASIC functionality with best in class ultra-narrow line-width tunable lasers, high speed modulators and high responsively coherent receivers to deliver high performance at 400G 16QAM modulation formats (at 60G baud rate). C Band 75/100GHz 400G Coherent Module QSFP-DD ZR 80~120KM for DCI Applications 0 Features QSFP-DD MSA compliant Compliant with OIF 400ZR, version 01.0, March 10, 2020 Digital diagnostic monitoring support Hot pluggable by 76-pin electrical interface Maximum power consumption 16.5 W 400G 16QAM modulation Compact size (18.4 mm x 93.4 mm x 8.5 mm) LC duplex connector 400GBASE-R, 425 Gbps bit rate 400G-AUI-8 C2M; 8 x CEI-56G-VSR PAM-4 electrical interface Operating case temperature: 0°C to 70°C Single 3.3 V power supply RoHS 2 compliant Optical Characteristics Parameter Min Typ Max Unit Conditions Transmitter Transmitter frequency range 191.3 193.7 196.1 THz TU-T grid. Frequency range over which the specifications hold unless noted otherwise. The frequency is fixed at 193.7 THz for unamplified link applications. Transmitter laser frequency stability -1.8 1.8 GHz Offset from channel frequency set point. The receiver LO has the same frequency accuracy. Transmitter output power -10 -6 dBm Measured at optical connector. Transmitter output power with TX disabled -20 dBm Max Output power with TX_DIS asserted Transmitter output power during wavelength switching -20 dBm Transmitter reflectance -20 dBm Transmitter polarization dependent power Mean I-Q amplitude imbalance 1 dB Transmitter polarization dependent power 1.5 dB Power difference between X and Y polarization Receiver Frequency offset between RX and LO -3.6 3.6 GHz Acquisition Range Input power range -12 0 dBm Input sensitivity (amplified link application) -12 dBm Input sensitivity (unamplified link application) -20 dBm For unamplified link applications, the minimum input power is –20 dBm @receiver OSNR tolerance ≥ 34 dB. OSNR tolerance (amplified link application) 26 dB/0.1nm The OSNR tolerance is referenced to an optical bandwidth of 0.1 nm @193.7 THz or 12.5 GHz. OSNR tolerance (unamplified link application) 34 dB/0.1nm The OSNR tolerance cannot be less than 34 dB for unamplified link applications. Optical return loss 20 dB Optical reflectance at connector input CD Tolerance 2400 ps/nm Tolerance to chromatic dispersion Optical path power penalty 0.5 dB OSNR penalty tolerance due to –35 dB interferometric crosstalk and 2400 ps/nm chromatic dispersion. PMD tolerance 10 ps Tolerance to PMD with ≤ 0.5 dB penalty to OSNR sensitivity. 10 ps of PMD corresponds to max 30 ps of DGD and max 500 ps2 of SOPMD PDL tolerance (amplified link application) 3.5 dB Tolerance to PDL with < 1.3 dB penalty to OSNR sensitivity When change in PSP is ≤ 1 rad/ms. PDL tolerance (unamplified link application) 2.5 dB The PDL tolerance is 2.5 dB in unamplified link application when the reciever OSNR sensitivity penalty is 0.8 dB. Tolerance to change in SOP 50 krad/s Tolerance to change in SOP with ≤ 0.5 dB penalty to OSNR sensitivity. Measurement relative to reference with 10 ps PMD and 2.5 dB PDL and SOP of < 1 rad/ms under the same conditions. Optical input power transient tolerance ±2 dB Tolerance to change in input power with ≤ 0.5 dB penalty to OSNR sensitivity. Received power is within –12 dBm to 0 dBm. Rise/fall times of power change defined by 20%–80% of 50 µs or slower.

PRODUCT DESCRIPTION PLC fiber optic Splitter 1x8 blockless mini module with fan-out kits LC/APC, SC/APC 1x8 Fiber optic PLC Splitter is also called 1*8 fiber optical plc splitter, optic fiber plc splitter, optical fiber plc splitter, plc fiber optic splitter or plc optical fiber splitter. We can produce the fiber optical splitter with connector or without connector! Fiber optic PLC Splitter Description: PLC splitter are based on Planar Waveguide Technology. They provide a cost effentive and space saving networking solution. They are key components in FTTx networks and are responsible to distribute the signal from central office to numbers of promises. They have very wide range of operatng wavelength from 1260nm to 1620nm. With it’s compact size, these splitters can be utilized in in-gruond and earial pedestals as well as rack mount system. It is used for small spaces can be easily placed in a formal joint boxes and splice closure, in order to facilitate welding, does not need specially designed for spave reserved. Our PLC splitter family features either ribbon or individual fiber output, We provides whole series of 1xN and 2xN splitter products that are tailored for specific applications. All splitters provide guaranteed optical performanve and high reliability that meet GR-1209-CORE and GR-1221-CORE requirement. Fiber optic PLC Splitter Options: - 1xN: 1x2, 1x4, 1x8, 1x16, 1x32, 1x64 splits. - 2xN: 2x2, 2x4, 2x8, 2x16, 2x32, 2x64 splits. - Un-connectorized. - Fiber jacketing outside boxes 2mm and up to 3mm. - ABS box type or inside metal box/module cassette type. - SC/UPC, SC/APC, LC/UPC, LC/APC, FC/UPC, FC/APC, ST/UPC, ect connector options. - Custom connector configurations and combinations. Fiber optic PLC Splitter Applications: - Fiber to The Point (FTTX). - Fiber to The Home (FTTH). - Passive Optical Networks (PON). - Gigabit Passive Optical Networks (GPON). - Local Area Networks (LAN). - Cable Television (CATV). - Test Equipment. Fiber optic PLC Splitter Features: - Low insertion loss. - Low Polarization Dependent Loss. - Excellent Environmental Stability. - Excellent Mechanical Stability. - Telcordia GR-1221 and GR-1209.

100Base FX Multi Mode Rugged SFP GLC-FE-100FX-RGD Cisco Transceiver Module GLC-FE-100FX-RGD Overview The GLC-FE-100FX-RGD is a third-party compatible SFP for Cisco. This 100BASE module will reach 2km and uses a wavelength of 1310nm. All GLC-FE-100FX-RGD are in-system tested in real Cisco routers and switches. This Cisco compliant GLC-FE-100FX-RGD is a 100BASE-FX SFP 1310nm 2km transceiver module. The GLC-FE-100FX-RGD transceiver module provides a low cost high-performance connection. The GLC-FE-100FX-RGD is 100% compatible with all Cisco series switches and modules which support SFP transceivers. Features & Specifications Form Factor: SFP Device Type: Transceiver module Interface (Bus) Type: Plug-in module Connectivity Technology: Wired Application: 100BASE-FX Data Transfer Rate: 100Mbps Wavelength: 1310nm Max Distance: 2km Fiber Type: SMF/MMF Connector: Duplex LC DDM: Without DDM Operating Temperature: 0~70 °C Compliant with MSA SFP Specification GLC-FE-100FX-RGD Specifications Product Name GLC-FE-100FX-RGD Media Fiber Wavelength 1310nm Data Rage OC48 Mode LC Connector Type SM Distance 2km 1310nm 2KM Cisco Transceiver Module 100Base FX Multi Mode Rugged SFP GLC-FE- 100FX-RGD 0 FAQ 1. Where do your products come from? All of our products are from Cisco/Huawei distribution , Cisco/Huawei partner directly. We are Cisco partner at local, with cisco verified certification. 2. If all equioments I can buy service from local cisco ? For all equipments you can buy service from local, because our goods are smart net free, all with clean serial number. 3. How to ship the goods? Lonrise work with DHL,FEDEX,UPS and TNT. Your order will be dispatched by express delivery door to door. 4. What’s your payment term? We always accept 10% advance payment. For long term cooperation, we can consider to apply credit accordingly. Related products SFP-10G-SR SFP-10G-LRM SFP-H10GB-CU3M SFP-10G-ER SFP-10G-ER QSFP-H40G-CU3M QSFP-H40G-CU0-5M QSFP-H40G-CU5M QSFP- 4SFP10G-CU1M