2G GPS TRACKER WITH CUT OFF FUEL

1.Specifications
Product name Wireless data terminal
Model 303FG
DIM. 9.6×5.3×1.6cm
Weight 70g
Network GSM/GPRS
Band 850/900/1800/1900Mhz
GPS sensitivity -165dBm
GPS accuracy 5m
Time To First Fix Cold status 45s
Warm status 35s
Hot status 1s
Applicable car power 12V-24V
Battery Chargeable 3.7V 350mAh Li-ion battery
Storage Temp. -40°C to +85°C
Operation Temp. -20°C to +65°C
Humidity 5%--95% non-condensing
2. Hardware Description



3. Terminal Installation
1.Please ask a qualified engineer to install it.
2.The installation environment should ensure that the GSM and GPS signals
are good
3.Please do not install it in a dusty and humid environment.
4.Find the 12PIN wiring harness provided with the product, insert it into
the corresponding wiring hole of the product, and connect to the original
car circuit as shown in the following Wiring Diagram:

5.The pink wire can be connected to the original car alarm horn or the
alarm horn purchased together.
6.Understand that the vehicle door trigger type is positive trigger or
negative trigger. Connected to the green wire if it is positive trigger,
and connected to the blue wire if it is negative trigger.
7.Please install the SOS button where the driver can touch it.
8.SIM card installation
Please use the included screwdriver to open the case to insert the SIM
card. If you intend to expand the storage space, then please insert micro
SD and then assemble the case.
Please be sure to confirm that the SIM card network frequency band is the
network frequency band supported by the device. Caller ID must be turned on
and the PIN code must be turned off. The call forwarding function cannot be
turned on.

9.After inserting the SIM card, connect the positive and negative (red and
black) wires of the power supply to the 12V or 24V power supply of the car.
Wait the device works normally After 1 minute of power-on, and then turn on
the Backup battery switch.
4. Device Status Light
Red light: Always on when charging, and turns off after being fully
charged. Red light flashes quickly when battery is low.
Green light: Flashes every 1 second when GSM network signal normally,
flashes every 3 seconds when works in GPRS mode; always on when no GSM
network.
Blue light: Flashes every 1 second when GPS signal is normal; flashes 3
times per second when GPS signal is very good (at least 4 satellites with a
signal-to-noise ratio of more than 38), and turns off if lost fix to
satellites.
5. Mobile APP
Scan the QR code to download APP

Google Play、App Store、Baidu App Store search “BAANOOL IOT” to download
it
Register
Open BAANOOL IOT, register a new account and login, Choose “BAANOOL car “to
enter it.


Bind Device
Click “Me”“Device Management”“Add”, scan the QR CODE on the device or
enter
the IMEI manually to bind the device


6. BAANOOL IOT’s Web Version
Open www.baanooliot.com , The login account name and password are the same
as phone app’s


Attention：
When reading this user manual, you will notice that we have used "+" and
"space"
between some words;"+" between two words means they should be written
together as one word and "space" between two words means you should leave
one
character space between two words.
7. GPRS configuration for live real-time tracking
Set APN, Account user name and password to login web platform
Usually, the device can automatically recognize and select the APN, user
name and password of GPRS settings. If the device cannot connect to the web
platform, then you need to use the mobile phone text message to configure
the settings according to following steps.
7.1 APN Setting
APN is an abbreviation for Access Point Name and changes depending on
which mobile network you are using. For more information about your local
APN, please check with your local wireless carrier.
SMS command: APN+password+space+local APN
Tracker response: APN OK
Example: APN123456 CMNET
Note: 123456 is the default password, please change password on APP or
refers to 8.1.
7.2 Configure user name and password of GPRS
In the most countries, the user name and password of GPRS are not
necessary;
therefore, you can ignore this step if it is not necessary for your local
network.
For those countries requiring user name and password, please configure as
following:
SMS command: up+password+space+user+space+password
Tracker response: user, password ok!
Example: up123456 Jonnes 666666
Note: 123456 means the password of the device, Jonnes means the user name
ofgprs, and 666666 means password of gprs
7.3 Configure domain name and port
Tracker connects to tracker.baanooliot.com 8090 by default. If you need to
connect to another domain name, please configure it.
SMS command: dns+password+space+DNS domain name+space+port
Tracker response: dns success!
Example : dns123456 tracker.baanooliot.com 8090
Note:
If you want to configure IP instead of DNS, then please send SMS command:
“adminip+password+space+IP+space+port”
, 7.4 GPRS mode
SMS command: GPRS+password
Tracker response: GPRS OK! (It means it has been switched to GPRS mode.)
8. Function Details
The following setting functions can be set through the APP or web version
676788.1 Changing Password
8.1.1SMS command: password+oldpassword+space+new password
Tracker response: password OK
8.1.2Be sure to keep the new password in mind, you have to flash the
firmware to restore the initialized setting in case of losing the new
password
8.1.3Attention: Make sure the new password is in 6 digits Arabic numbers,
otherwise the tracker cannot recognize it
8.2 Authorization
Up to 5 numbers can be authorized.
8.2.1call the tracker 10 times in succession, the number will be authorize
automatically as the first number and tracker response “add master ok”
8.2.2SMS command: admin+password+space+mobile phone number ,
Tracker response: admin ok。
8.2.3SMS command: noadmin+password+space+authorized number
Tracker response: noadmin ok
8.2.4If you want to receive these kinds of notification alerts when the
trackers moved to another country, you must put the country code before the
phone number to authorize it in international format, If there is a “0”
before your phone number, please remove the “0”, for example, admin123456
008613322221111, then 13322221111 had been configure to authorization
number。

Minimum Order: 1 sets

Click to Enlarge