Agricultural Equipment

TL-5 burning furnace is consists of 5 parts: a blower, flue gas induced draft fan, burner, five-layer sleeve body and control system. The flue gas in the furnace takes two rounds while the fresh air takes three rounds. Natural gas is burned through the burner to generate a high-temperature flame. Under the action of the flue gas fan, the heat is transferred to the heated air through the five-layer sleeve wall and dense fins, meanwhile the flue gas is discharging out the body after it´s temperature down to 150℃. The heated fresh air enter the sleeves through blower. After heat mix, the temperature rises to the setting number and sent out from the hot air outlet. 4、Advantages/features 1. Continuously provide pure air with constant temperature and constant pressure. 2. Temperature has a wide adjustable range: 40~300℃ 3. Indirect heating, automatic operation, exhaust gas emissions meet the requirements 4. Reasonable design, compact structure, thermal efficiency up to 75% 5. Stainless steel high temperature resistant inner tank, durable

Minimum Order: 1 bags

The TL-4 burning furnace consists of 3 layers of cylinders. It uses fully burned natural gas to obtain high-temperature flame, and mixing this temperature with fresh air to achieve the required hot air device. Due to the use of fully automatic single-stage fire, two-stage fire or modulating burner, the output hot air is extremely clean by natural gas fully burned, , meeting the drying and dehydration needs for most stuffs. The external fresh air enter the furnace body under negative pressure, takes two strokes and sequentially cools the middle cylinder and the inner tank. After being fully mixed with the high-temperature flame in the mixing zone, it is extracted from the furnace body and enter the drying room. When the temperature reach the setting number, the main burner stops working and the auxiliary burner continues to burn to maintain the temperature. When the temperature drops to the set lower limit temperature, the main burner will be run again. 4、Advantages/features 1. Simple structure and easy installation 2. Small air volume, high temperature, adjustable from normal temperature to 500℃ 3. Stainless steel high temperature resistant inner tank, durable 4. Automatic gas burner, complete combustion, high efficiency. (After setting up, the system can control the ignition+cease fire+temperature adjust automatic), 5. The fresh air has a long stroke that can fully cool the inner tank, so the outer tank can be touched without insulation. 6. Equipped with high temperature resistant centrifugal fan, large pressure center and long lift

Minimum Order: 1 bags

TL-3 burning furnace is consists of 8 parts: natural gas burner + inner tank + insulation box + fan + fresh air damper + waste heat recovery device + dehumidification fan + control system. It is specially designed for supporting downflow drying room/heating rooms. After fully combusts the natural gas inside the inner tank, it´s mixed with recycle or fresh air, under the action of the fan, it is discharged from the upper outlet into the drying room or heating space. Then cooled air pass through the lower air outlet for secondary heating and continuous circulation. And when the humidity of circulating air reaches the emission standard, the dehumidification fan and fresh air damper will start simultaneously. The exhausted moisture and fresh air implement sufficient heat exchange in the waste heat recovery device, so the moisture is discharged and the fresh air with recovered heat enter the circulation system. 4. Advantages/features 1. Simple structure and easy installation 2. Large air volume and small wind temperature fluctuation 3. Stainless steel high temperature resistant inner tank, durable 4. Automatic gas burner, complete combustion, high efficiency. (After setting up, the system can control the ignition+cease fire+temperature adjust automatic), 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating. 7. Integrating the dehumidification and fresh air system, heat loss is extremely small through by the waste heat recovery device. 8. Automatically replenish fresh air

Minimum Order: 1 bags

TL-2 model Direct burning furnace is consists of 6 parts: natural gas burner + inner tank + insulation box + fan +fresh air damper + control system. It is specially designed to support the left and right circulation drying room. For example, the 100,000 kcal model drying room, it is equipped with 6 fans, three on the left and three on the right. When the three fans on the left rotate clockwise, the three fans on the right rotate counterclockwise in a cyclic alternating manner, forming a relay, The left and right sides serve as air inlets and outlets alternately, taking out all the heat generated by full combustion of natural gas. It is equipped with an electric fresh air damper to supplement fresh air in coordination with the dehumidification system in the drying room/drying place. 4. Advantages/features 1. Simple structure and easy installation 2. Large air volume and small wind temperature fluctuation 3. Stainless steel high temperature resistant inner tank, durable 4. Automatic gas burner, complete combustion, high efficiency. (After setting up, the system can control the ignition+cease fire+temperature adjust automatic), 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating. 7. left and right fans run alternately in cycles to ensure even heating 8. Automatically replenish fresh air

Minimum Order: 1 bags

ZL-3 steam air heater is consists of 9 parts: steel-aluminum radiator fin tube + electric steam valve + drain valve + insulation box + fan + Fresh air damper + waste heat recovery device + dehumidification fan + electric control system. It is specially designed for supporting downflow drying room/heating rooms. After convert the outside steam heat to heat inside the insulation box through by the fin tube, it´s mixing with recycle or fresh air, under the action of the fan, it is discharged from the upper outlet into the drying room or heating space. Then cooled air pass through the lower air outlet for secondary heating and continuous circulation. And when the humidity of circulating air reaches the emission standard, the dehumidification fan and fresh air damper will start simultaneously. The exhausted moisture and fresh air implement sufficient heat exchange in the waste heat recovery device, so the moisture is discharged and the fresh air with recovered heat enter the circulation system.Advantages/features 1. Simple structure and easy installation 2. Large air volume and small wind temperature fluctuation 3. Stainless steel electric heating finned tube, durable 4. Steel-aluminum finned tubes, high heat exchange efficiency. The base tube is made of 8163 seamless tube which is pressure-resistant and durable; 5. Electric steam valve controls the amount of inlet, automatically cuts off or opens according to the set temperature, so that can accurately controls the temperature. 6．High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating. 7. Integrating the dehumidification and fresh air system, heat loss is extremely small through by the waste heat recovery device. 8. Automatically replenish fresh air

Minimum Order: 1 bags

ZL-2 steam air heater is consists of 7 parts: steel-aluminum radiator fin tube + electric steam valve + drain valve + insulation box + fan+ Fresh air damper + electric control system. It is specially designed to support the left and right circulation drying room. For example, the 100,000 kcal model drying room, it is equipped with 6 fans, three on the left and three on the right. When the three fans on the left rotate clockwise, the three fans on the right rotate counterclockwise in a cyclic alternating manner, forming a relay, The left and right sides serve as air inlets and outlets alternately, taking out all the heat generated by steam heater. It is equipped with an electric fresh air damper to supplement fresh air in coordination with the dehumidification system in the drying room/drying place. 1.Simple structure and easy installation 2. Large air volume and small wind temperature fluctuation 3．Steel-aluminum finned tubes, high heat exchange efficiency. The base tube is made of 8163 seamless tube which is pressure-resistant and durable; 4. Electric steam valve controls the amount of inlet, automatically cuts off or opens according to the set temperature, so that can accurately controls the temperature. 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating. 7. left and right fans run alternately in cycles to ensure even heating 8. Automatically replenish fresh air

Minimum Order: 1 bags

ZL-1 steam air heater is consists of 6 parts: steel-aluminum radiator fin tube + electric steam valve + drain valve + insulation box + fan + electric control system. Steam passes the though the fin tube, dissipating heat to the insulation box, mixing and heating the fresh or recycle air to setting temperature, fans bring this hot air into drying room or heating room to be used for dehydration, dehumidification or heating. 4. Advantages/features 1. Simple structure, beautiful appearance, low cost 2. Steel-aluminum finned tubes, high heat exchange efficiency. The base tube is made of 8163 seamless tube which is pressure-resistant and durable; 3. Electric steam valve controls the amount of inlet, automatically cuts off or opens according to the set temperature, so that can accurately controls the temperature. 4. Large air volume and small wind temperature fluctuation 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating.

Minimum Order: 1 bags

DL-3 electric air heater is consists of 7 parts: electric heater + insulation box + fan + fresh air damper + waste heat recovery device + dehumidification fan + control system. It is specially designed for supporting downflow drying room/heating rooms. After convert electrical energy into heart through by the electric heater, it´s mixed with recycle or fresh air, under the action of the fan, it is discharged from the upper outlet into the drying room or heating space. Then cooled air pass through the lower air outlet for secondary heating and continuous circulation. And when the humidity of circulating air reaches the emission standard, the dehumidification fan and fresh air damper will start simultaneously. The exhausted moisture and fresh air implement sufficient heat exchange in the waste heat recovery device, so the moisture is discharged and the fresh air with recovered heat enter the circulation system. 4. Advantages/features 1. Simple structure and easy installation 2. Large air volume and small wind temperature fluctuation 3. Stainless steel electric heating finned tube, durable 4. Automatic control system, group start and close, low load, precise temperature control 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating. 7. Integrating the dehumidification and fresh air system, heat loss is extremely small through by the waste heat recovery device. 8. Automatically replenish fresh air

Minimum Order: 1 bags

DL-2 electric air heater is consists with 6 parts: electric heater + inner tank + insulation box + fan +fresh air damper + control system. It is specially designed to support the left and right circulation drying room. For example, the 100,000 kcal model drying room, it is equipped with 6 fans, three on the left and three on the right. When the three fans on the left rotate clockwise, the three fans on the right rotate counterclockwise in a cyclic alternating manner, forming a relay, The left and right sides serve as air inlets and outlets alternately, taking out all the heat generated by electric heater. It is equipped with an electric fresh air damper to supplement fresh air in coordination with the dehumidification system in the drying room/drying place. 4、Advantages/features 1. Simple structure and easy installation 2. Large air volume and small wind temperature fluctuation 3. Stainless steel electric heating finned tube, durable 4. Automatic control system, group start and close, low load, precise temperature control 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating. 7. left and right fans run alternately in cycles to ensure even heating 8. Automatically replenish fresh air

Minimum Order: 1 bags

My name is susan and I work for XT Intelligent co.,ltd and I would like to take a moment of time to introduce you to our drying system. Our High Efficiency Multi Phase (flowers, leaves such as Rose,pepper etc) dryer combines established drying and processing techniques into a unique attrition flash drying process that keeps your items undamaged. This provides a timely and cost-effective means of stabilizing your valuable harvest before mold, mildew or composting can occur, allowing for future processing at a pace you determine. We design systems to your requirements, let us know your harvested moisture level is (%) as well as your capacity requirements, in “wet/harvested hemp in” lbs/hour and we will provide dryer budget estimates. There is more information, pictures and video at our website. My contact information is below, I would enjoy learning about your farm, call me if you have a few minutes to discuss your drying requirements. All the best, Susan Zheng XT Intelligence Technology Co.,Ltd E-mail : Susan205060@hotmail.com Wechat:+86 13671955713 Skype: Susan205060 Cell Phone: 0086-136 7195 5713 https://www.facebook.com/BELTDRYERMANU , FACTURER (20+) UL/CE parts belt dryer /box dryer Manufacturer - XT Facebook

1hp Aerator 1hp Fish Farming Aquaculture Aerator Paddle Wheel Areators Aerating A Pond With the continuous development of aquaculture fisheries, intensive high- yielding aquaculture technology has been widely used, fishery farming increased significantly. In the process of aquaculture production increase, aerator has become an essential equipment to achieve high-yield fisheries intensive, plays an important role in the development of fishery economy. Reasonable use of oxygen machine can effectively increase the dissolved oxygen in the pool water, accelerate the pond water body material circulation, reduce or eliminate harmful substances, and promote plankton breeding. For the prevention and mitigation of fish floating head, to prevent flooding and improve pond water quality conditions, increase the amount of fish fed and increase yield and so have a good role in promoting. Because of its light, easy to operate and single aerator function, it is generally suitable for the water depth below 0.7 meters, the area below 0.6 mu of fish fry breeding ponds or greenhouse ponds. With the continuous refinement of the fishery demand and the continuous improvement of the aerator machine technology, there are many new aerator machine, such as: spurting aerator machine, spray aerator machine and other specifications of the aerator machine.

Machine introduction This machine has a compact structure. Works steady, high output, small particle size. The contact part with food is made of stainless steel. It is non-pollution to material and meets with food hygienic. The grinding head have made heat treatment and it is made of high quality stainless steel. Good wear-resisting property. Long life service. This machine is easy to wash and it can process many kinds of material. The processed material still keep the original nutritional ingredient of the raw material. Good preservation effect. The grinding head can be changed according to different material. This machine is the best choice for meat processing factory, pet food processing factory and Biological health care products factory.

Minimum Order: 1 bags

It is full automatic,made of polyethelene.

Minimum Order: 1 bags

Corn grits making machine is the equipment that can process corn kernels into corn grits and cornflour. Nowadays, corn grits and corn flour are the most common forms of corn consumed in people’s daily life. Because the ground corn is easy to eat and digest and can be further processed into foodstuff. Therefore, the corn grits machine has become popular in the market.

Minimum Order: 1 bags