Construction Machinery

YB500 mortar spraying machine with high conveying efficiency and longer pumping distance. YB500 is a mortar spraying machine which is modified and upgraded on the basis of YB400. It adopts higher power motor, which is more suitable for the current construction technical requirements, with high conveying efficiency and longer pumping distance. https://www.qijiu-machine.com/product , -mortar-spray-machine.html power supply 380V Power 7.5KW Air compressor power 2.2KW Vertical conveying distance 20M Horizontal conveying distance 30M maximum aggregate particles ≤5mm Conveying capacity 3m³ / h Delivery hose 32mm weight 180Kg Dimensions 1600 * 550 * 1200mm

Minimum Order: 1 bags

ZW-15 stationary pump is designed for heavy working conditions. Concrete output: 6-8m³/h Reliable equipment quality Small secondary construction column pumps mostly use dual-pump, dual-circuit open hydraulic systems. The pumping system is simple, the components have a long service life and high reliability. Fully enclosed structural electrical control box, protection control device can work under harsh conditions. The Plc dual system control design simplifies the circuit while significantly improving its reliability and lifetime. Make the equipment work continuously. https://www.qijiu-machine.com/pro , duct-concrete-pump-zw-15.html Product use: Effectively solve the problem that the top of the bottom column is difficult to be poured in high quality during the pouring process of the structural column, and the flatness and the perceived quality of the structural column are guaranteed. JOKI Stationary concrete pump is suitable for high-rise concrete fine stone transportation, construction floor group structure column pouring, high pumping efficiency, pumping system is ten times of manual construction, which effectively improves production efficiency and saves labor cost. It is secondary structural column pouring. A good helper. The secondary construction column pouring machine is small in size, simple in operation, low in labor intensity, flexible in construction on the floor, and can be placed close to the lintel and the pillar. Model ZW-15 power supply 380V Power 15KW Output 6-8m³/h Greatest pressure/ Work pressure 18Mpa&10Mpa Vertical conveying distance 60M Horizontal conveying distance 30M The max diameter of aggregate ≤2cm Duct diameter 80mm weight 750Kg Dimensions 1800*680*1250mm

Minimum Order: 1 bags

JOKI Trailer Mounted Concrete Pump ZW-20 Trailer-mounted concrete pump with compact size. Concrete output: 8-15m³/h ZW-20 Concrete Pump Introduction: The new JOKI ZW-20 trailer mounted concrete pumps as supplied by Qijiu come in an array of outputs 15 cubic meters per hour over distances of 80m. Our trailer-mounted small concrete pumps offer the ideal solution for placing concrete or shotcrete in hard–to-access areas because of their compact size, they can also be used as an alternative to truck-mounted concrete pumps on larger pours that require a slower output rate. Concrete Trailer Pumps Specifications: Model ZW-20 Concrete Pump Concrete output/m³ 8-15 Concrete Pressure/Mpa 11 Hydraulic Pump Output/cc 80 Horizontal Pumping Distance/m 80 Vertical Pumping Distance/m 40 Power 22Kw motor or 40Kw Diesel Engine Vertical Pumping Distance/mm 120*800 Maxinmun Aggregate/mm 20 Hydraulic Oil Capacity/L 100L Outlet Size/mm 80 Dimensions/mm 2400*1000*1300 Weight/Kg 1100 Concrete Pump Trailer Advantages: Reliable equipment quality, small secondary construction column pumps mostly use dual-pump, dual-circuit open hydraulic systems. 1.The concrete pump trailer moves faster from the source to the pouring location, which can make you reach the area that the crane cannot reach. 2The pumping system is simple, the components have a long service life and high reliability. 3Fully enclosed structural electrical control box, protection control device can work under harsh conditions. 4The Plc dual system control design simplifies the circuit while significantly improving its reliability and lifetime. Make the equipment work continuously. Trailer Mounted Concrete Pump JOKI Use: Effectively solve the problem that the top of the bottom column is difficult to be poured in high quality during the pouring process of the structural column, and the flatness and the perceived quality of the structural column are guaranteed. Trailer mounted concrete pump is suitable for high-rise concrete fine stone transportation, construction floor group structure column pouring, high pumping efficiency, pumping system is ten times of manual construction, which effectively improves production efficiency and saves labor cost. It is secondary structural column pouring. A good helper. The secondary construction column pouring machine is small in size, simple in operation, low in labor intensity, flexible in construction on the floor, and can be placed close to the lintel and the pillar.https://www.qijiu-machine.com/product-concr , ete- pump.html

Minimum Order: 1 bags

Electric motor or Diesel motor 2 options. Concrete output: 15-20 m³/h The JOKI ZW-30 concrete pumps as supplied by Qijiu come in an array of outputs ranging from 15 cubic meters to 20 cubic meters per hour over distances of 260-350m. Our trailer-mounted concrete pumps offer the ideal solution for placing concrete in hard–to-access areas because of their compact size, they can also be used as an alternative to truck-mounted concrete pumps on larger pours that require a slower output rate. Model ZW-30 Concrete output/m³ 15-20 Concrete Pressure/Mpa 12 Hydraulic Pump Output/cc 80 Horizontal Pumping Distance/m 260-350 Vertical Pumping Distance/m 100-120 Power 37Kw motor or 44Kw Diesel Engine Concrete Cylinders/mm 140*750 Maxinmun Aggregate/mm 30 Hydraulic Oil Capacity/L 150L Outlet Size/mm 100(80) Dimensions/mm 4000*1200*1400 Weight/Kg 1800

Minimum Order: 1 bags

The new ZW-20 concrete pumps as supplied by Qijiu come in an array of outputs 15 cubic meters per hour over distances of 80m. Our trailer-mounted concrete pumps offer the ideal solution for placing concrete or shotcrete in hard–to- access areas because of their compact size, they can also be used as an alternative to truck-mounted concrete pumps on larger pours that require a slower output rate. Electric motor or Diesel motor 2 options. Concrete output: 8-15m³/h You can click here to get the concrete pump price Model ZW-20 Concrete output/m³ 8-15 Concrete Pressure/Mpa 11 Hydraulic Pump Output/cc 80 Horizontal Pumping Distance/m 80 Vertical Pumping Distance/m 40 Power 22Kw motor or 40Kw Diesel Engine Vertical Pumping Distance/mm 120*800 Maxinmun Aggregate/mm 20 Hydraulic Oil Capacity/L 100L Outlet Size/mm 80 Dimensions/mm 2400*1000*1300 Weight/Kg 1100 Reliable equipment quality Small secondary construction column pumps mostly use dual-pump, dual-circuit open hydraulic systems. The pumping system is simple, the components have a long service life and high reliability. Fully enclosed structural electrical control box, protection control device can work under harsh conditions. The Plc dual system control design simplifies the circuit while significantly improving its reliability and lifetime. Make the equipment work continuously. Product use: Effectively solve the problem that the top of the bottom column is difficult to be poured in high quality during the pouring process of the structural column, and the flatness and the perceived quality of the structural column are guaranteed. It is suitable for high-rise concrete fine stone transportation, construction floor group structure column pouring, high pumping efficiency, pumping system is ten times of manual construction, which effectively improves production efficiency and saves labor cost. It is secondary structural column pouring. A good helper. The secondary construction column pouring machine is small in size, simple in operation, low in labor intensity, flexible in construction on the floor, and can be placed close to the lintel and the pillar.https://www.qijiu-machine.com/product.html

Minimum Order: 1 bags

ZW-40 is a lightweight, compact, road-towing trailer pump. Its combination of powerful pumping, at 40m³/hour, and small size make it perfect for contractors undertaking multiple pours in a day. In length and in width, it can pump up to 30mm concrete at a horizontal reach of 450-500m and a vertical reach of 180m (dependant on concrete quality, slump and aggregates). Model ZW-40 JOKI Trailer Mounted Concrete Pump Concrete output/m³ 30-40 Concrete Pressure/Mpa 13 Hydraulic Pump Output/cc 112 Horizontal Pumping Distance/m 450-550 Vertical Pumping Distance/m 180 Power 45Kw motor or 56Kw Diesel Engine Concrete Cylinders/mm 160*1000 Maxinmun Aggregate/mm 30 Hydraulic Oil Capacity/L 200L Outlet Size/mm 100(80) Dimensions/mm 4000*1500*1550 Weight/Kg 2200

Minimum Order: 1 bags

30*30/25*38 Square tube & Rectangle Pipe forming machine technology (Steel tube thickness less than 3.5mm) Model SP-IN4 Motor power 7.5KW Reducer 350 type Feed material iron pipe Feeding round tube diameter 1.5 inch (cun) Forming Roller 8 forming + 2 straightening Working speed 10 meters / minute Roller material GCr15 heat treatment after finishing Spindle material 40Cr after quenching and tempering Transmission mode 1.2 inch chain sprocket drive What are the environmental protection features of square tube forming machine The square tube forming machine is widely used because of its green environmental protection characteristics. It uses less and less stainless steel plate demand to carry out the specific load that needs to be exceeded. It is no longer completely relying on increasing the demand for plates or improving the physical properties of raw materials. To consider the requirements of the load, it is only to improve the physical properties of the channel steel according to the cross-sectional appearance of the channel steel product. In the main purpose of the square tube forming machine, the advantages of the square tube forming machine are more and more understood by customers. It belongs to the rapid economic development of the cross-sectional stainless steel sheet, which can save 15-30% of metal materials. The project investment is small, and the production is flexible. Various regulations that can meet the needs of customers highlight its unique advantages in the development trend of the humanized sales market. The square tube forming machine is generally used to replace hot rolled aluminum profiles and other types, which has become an unstoppable development trend of square steel tube forming methods

Minimum Order: 1 bags

Steel round pipe how to change into rectangle pipe. Rectangle size 1"*2", 1"*3",1"*4" etc size all available. Input round pipe size is import for making shape rectangle pipe. Steel Round Pipe change into square & rectangle pipe forming machine operation guide 1. Develop safe operating procedures. Do not touch the mold during the operation of the unit. If you need to touch it during work, your hands should be placed in the direction of the pipe. Operators should have fixed positions, not change at will, and keep a record of shifts. 2. Before driving, check whether the lubrication points of the steel square tube forming machine are filled with corresponding lubricants. Pay special attention to the high-speed lubricating grease that is relatively high- temperature resistant to the main shaft of the flying saw. Fill it once every two days, two or three times each time. It should not be added too much. If the heat dissipation is not good.

Minimum Order: 1 bags

KES is specializing in manufacturing truck parts and systems from cylinders and gladhands to transfer cases. We also offer services like electric motor body casting, automotive aluminum patrs die casting and so on. KES factory has strong technical force, a strong ability to develop new products, exquisite inspection methods for auto parts die-casting technology. KES produces die-casting auto parts and regards quality as its life, takes science and technology as the guide, and continuously introduces new products, like molten metal under high pressure which is a casting method that die- casting auto parts are filled at high speed and solidified under pressure. For automobile parts made by casting, lightweight structures must be realized. This goal can be achieved in various ways: the choice of structure and materials, as well as the processing technology, will have a decisive influence on the weight of the product. And the casting process offers various possibilities to make the product lighter. It allows a high degree of design freedom in order to place the correct material in the correct position and helps to integrate multiple functions into one product. Regarding the high requirements for performance and quality, casting provides a very wide range of solutions, even in a constantly changing environment, which can provide attractive methods for auto&motors parts applications. New materials, innovative design concepts, and modern manufacturing processes will continue to provide the basis for competitive and affordable lightweight structures in the future. What should be particularly mentioned is that the casting material is easy to recycle and therefore has continuous carbon dioxide efficiency. In order to provide more valuable solutions for automobiles in the future, further ideas are needed. Materials with enhanced properties, combined with new product boundaries with minimum wall thickness, will help continue to achieve attractive, economical lightweight structures. KES ( Shenzhen Kangensheng Technology Co., Ltd. ) is a professional aluminum auto parts manufacturers. We provide Aluminum Die Casting, Zinc Die Casting, Cold Chamber Die Casting, automotive casting components, casting car parts, die casting automobile parts, casting parts in automobile, automotive aluminum die casting, aluminium die casting and etc. Want to know about die casting steps? Please contact us.

Resilient-seated gate valve with bolted cover connection; made of ductile iron materials and with epoxy coating designed in both clockwise and anti-clockwise directions. Gate valve is mainly used to connect and cut off the medium in the pipeline by rotating the stem. DN size: DN50~DN300 Pressure rating: PN10/PN16 Connection: Euro socket for PVC pipe Fusion bonded epoxy coating Certifications: CE/EN1074/WRAS/ACS

Flip rubber check valves with resilient seat for pumping applications to prevent back flow avoiding damage to the piping components. They can be used for drinking water as well as wastewater applications. All the internal components are coated with WRAS approved epoxy or EPDM. Specifications Size range: DN 50 to DN 600 Pressure rating: PN 10 / PN 16 Connection: Double flanges Standard: BS5153/ DIN3202F6 Coating: Epoxy coating Certfications : CE/EN1074/WRAS/ACS

Minimum Order: 1 bags

This type of strainer for the pipeline needs to be cleaned often, to make sure that the filtering ability of the device is not jeopardized by the accumulation of debris. The pipeline can be kept in service, generally, when y-strainers need a cleanup. Specifications Size range: DN 40 to DN 600 Pressure rating: PN 10 / PN 16 Connection: Double flanges Standard: BS2080/ DIN3202F1 Screen: SS304 Coating: Epoxy coating Certfications : CE/EN1074/WRAS/ACS

Minimum Order: 1 bags

Best Quality Hollow Section Product details Galvanized Square & Rectangular Tube 15mm*15mm-800mm*800mm20mm*30mm-600mm*800mm , 1.0mm-30mm  1m-16m Q195 → SS330,ST37,ST42Q235 → SS400,S235JRQ345 → S355JOH,SS500,ST52 EN10219; ASTM A500 1) Plastic pipe cap2) Iron protector 1) Bared2) Black Painted (varnish coating)3) Galvanized4) Oiled5) PE,3PE, FBE, corrosion resistant coating, Anti corrosion coating. Electronic Resistance Welded (ERW )Electronic Fusion Welded (EFW)Double Submerged Arc Welded (DSAW) 1) Container2) Bulk carrier Tianjin, China（Mainland） L/C, T/T, D/P, O/A hot-dipped galvanised steel tube Sizes we can supply Rectangular Hollow Section Square Hollow Section Size Thickness Size Thickness Size Thickness mm mm mm mm mm mm 50 X 25 2.0 120 X 40 3.0 20 x 20 2.0 50 X 25 2.5 120 X 40 3.6 20 x 20 2.5 50 X 25 3.0 120 X 40 4.0 25 x 25 2.0 50 X 30 2.5 120 X 40 5.0 25 x 25 2.5 50 X 30 3.0 120 X 40 6.0 25 x 25 3.0 50 X 30 3.2 120 X 40 6.3 30 x 30 2.5 50 X 30 4.0 120 X 60 3.0 30 x 30 3.0 60 X 40 2.5 120 X 60 3.6 40 x 40 2.0 60 X 40 3.0 120 X 60 4.0 40 x 40 2.5 60 X 40 3.2 120 X 60 5.0 40 x 40 3.0 60 X 40 4.0 120 X 60 6.0 40 x 40 4.0 Sino Steel Impex Co., Ltd. is a China Best Quality Hollow Section supplier, you can be get most careful and thoughtful service! If you want to know more products click here.

Pre-Galvanized Steel Pipe (Round) HOT DIP GALVANINZED STEEL PIPE Best Quality Galvanized Steel Pipe Product details Name Pre - galvanized tube OD 1/2” -8” (20mm-219mm) Wall thickness 0.7mm-2.5mm Length 0.5m~7.2m Steel material Q195 Q235 Q345 Standard JIS3444, EN10255, BS1387, EN10219 Zinc coating 40g~270g6μm~35μm Ends 1) Plain2) Beveled3) Thread with Coupling or cap4) Chamfer5) Groove6) Screw End protector 1) Plastic pipe cap2) Iron protector Technique Electronic Resistance Welded (ERW )Electronic Fusion Welded (EFW) Section shape Round Inspection With Hydraulic Testing, Eddy Current , Infrared Test Delivery 1) Container2) Bulk carrier Port of Shipment Xinggang Port,Tianjin, China Date of Delivery According To The Quantity And Specification Of Each Order Payment L/C, T/T, D/P  Sino Corrosion Resistant Galvanized Steel Pipe Packing &Shipping 1) Packing details: ①  in bundles by steel strips; ②  bundles with damp-proof package or Woven cloth; ③  as per customer's requirement.     2) Delivery time: Normally 18-25 days after T/T or L/C or D/P confirmed. Sino Steel Impex Co., Ltd. is a China Galvanized Steel Pipe supplier, you can be get most careful and thoughtful service! If you want to know more products click here.