Electronic Measuring Instruments

Smart Single phase STS Split type keypad prepaid meter DDSY168-S The Smart DDSY168-S is a dual power source measuring , split type prepayment electricity meter, completed in BS footprint housing working with a separate dispay and keypad unit (UIU / CIU). It is an ideal revenue protection metering tool that can measure grid power and any other alternative power with no need to add extra components . In duall prepaid mode, the meter can auto decrypt the recharge code from source and top up into separate balance . Major Featureso 20 digit (Standard Transfer Specification) STS encryption Detection of significant reverse energy (SRE) IEC62056-21 compliant port allowing for easy data interrogation Disconnects on overload and no credit Operate in both prepayment and credit mode hot swap Programmable load limit and low credit warning Detection and record tamper event such as cover open, reversal, black-out, etc. Split Configuration for Increased Revenue Protection the meter consists of two parts, the MCU (Meteriing & Control Unit) and UIU (User Interface Unit). The MCU and UIU is linked via galvanically- isolated 2 -wire communication cable Power line carrier (PLC) and Radio Frequency (RF) communication module is also aviable on request. The UIU is installed within consumer's home, while MCU is installed in a meter cabinet away from consumers. Utility benefit Easy connection to User Interface Unit (UIU) for split type applications RF / GPRS wireless communication with a head-end AMR/AMI server Time of Use (TOU), multi-tariff, holiday setting. Advanced load control and disconnection features Specifications: Nominal voltage Un 220/230/240 V Limited voltage 70%~120%Un Nominal frequency fn 50-60Hz+5% Basic current(Ib) 5-10A Maximum current(Imax) 60-100A Starting current(Ist) 20mA Active energy constant 1000imp/kWh Accuracy as Active energy to IEC62053‐21 Class1.0 Power consumption in Voltage circuit <2W <8VA Power consumption in current circuit <1VA Operating temperature 25℃ to+70℃ Storage temperature 40℃ to+85℃ Insulation level 4kV rms for 1min Impulse voltage withstand 8kV, 1.2/50 μs Air discharge 16kV Immunity to HF fields 80MHz to 2GHz with load 10V/m 100kHz to 1GHz without load 30V/m Fast transient burst test 4kV Meter shell Protection Rate IP54(IEC60529) Insulation System Classification Protective Class II Infrared Optical 2W 20mA Prepaid Electricity Meters 1 Phase Energy Meter 0Infrared Optical 2W 20mA Prepaid Electricity Meters 1 Phase Energy Meter 1 Infrared Optical 2W 20mA Prepaid Electricity Meters 1 Phase Energy Meter 2

Product Description MSA015S LifeBeing sensor Breathing Detecting Technology/ON-OFF Innovative patent energy-saving switch, control lights ON-OFF automatically. Traditional switch is needless. A very sightly movement even human breathing can be collected, never worry a sudden shut-off when light is necessary. Interference-free with flying insects, falling leaves, air vent and wireless signal(WiFi, Bluetooth, 4G and 5G). Adjustable detecting settings, suitable for various places, such as toilet, kitchen, office, library, corridor etc.. Rated Voltage 220-240VAC 50/60Hz Stand-by Power <0.5W Load Capacity 400W (Inductive) 800W (resistive) Detecting Technology Movement / minor motion / breathing Working Mode On-off Operating Frequency 5.8 GHz ±75 MHz, ISM band Transmitting Power 0.5mW Max. Hold Time 5S/3Min/5Min/10Min/15Min/20Min/25Min/30Min Detection Area 100%/75%/50%/25% Daylight Sensor 5lux/25lux/50lux/Disable Mounting Height 3-6m Operating Temperature -25~55℃ IP Rating IP20 Breathing Detecting Microwave Motion Sensor MSA015S 0 Breathing Detecting Microwave Motion Sensor MSA015S 1 Breathing Detecting Microwave Motion Sensor MSA015S 2 Breathing Detecting Microwave Motion Sensor MSA015S 3 Breathing Detecting Microwave Motion Sensor MSA015S 4

Product Description ADL200 Din Rail Energy Meter ● AC220V ● 10(80)A ● RS485(MODBUS-RTU) ● Set parameters ● LCD display ● kWh Class 1 ● DIN 35 mm Characteristic KWh Class 1 ADL200 Din Rail Energy Meter With Digital LCD Display 0 KWh Class 1 ADL200 Din Rail Energy Meter With Digital LCD Display 1 KWh Class 1 ADL200 Din Rail Energy Meter With Digital LCD Display 2 Communication Display Rated U and I RS485 (Modbus-RTU) 8 digits LCD display U, I, P, Q, PF, kWh, Power measure (999999.99kWh) AC220V 10(80)A Function Accuracy kWh Class 1 Frequency 45~65Hz Power Supply (self suppy) 154~264Vac Pulse output kWh Input consumption <4VA KWh Class 1 ADL200 Din Rail Energy Meter With Digital LCD Display 3 KWh Class 1 ADL200 Din Rail Energy Meter With Digital LCD Display 4 Dimension(LWH) 90*36*65mm I , nstallation DIN 35 mm Clock Error ≤0.5s/d Starting current 0.04A LCD Display KWh Class 1 ADL200 Din Rail Energy Meter With Digital LCD Display 5 Wiring KWh Class 1 ADL200 Din Rail Energy Meter With Digital LCD Display 6 Typical Connection KWh Class 1 ADL200 Din Rail Energy Meter With Digital LCD Display 7

PRODUCT DESCRIPTION Features of GNSS GPS Survey Equipment Voice Broadcast Easily Operate Accurate Measurement One Year Warranty GPS + Beidou Dual Satellite Positioning,Support SBAS. S1 GNSS Measuring Tools 0

1. INTRODUCTION The instrument is a stable and high performance digital multimeter driven by battery. It uses the LCD with 42mm high make the reading is clearly. And the function of backlight and overload protection make operation is convenient. The instrument has the function of measuring DCV, ACV, DCA, ACA, Resistance and Capacitance, Frequency, temperature, Transistor, Diode and Continuity test. The instrument takes dual-integral A/D converter as key point, is an excellent tools. It’s an ideal tool for lab, factory and family. 2. SAFETY NOTES This series meter meets the standard of IEC1010. Read it before operation. 1．Do not input the limited voltage of 1000V DC or 750V AC RMS when measuring voltage. 2．Voltage less than 36V is safety voltage. When measuring voltage higher than 36V DC, 25V AC, check the connection, insulation of test leads to avoid electric shock. 3．When changing function and range, test leads should be removed from testing point. 4．Select correct function and range. 5．When measuring current, do not input current over 20A. 3.SPECIFICATIONS Display mode: LCD displaying. Max. indication :3999(3 3/4), auto polarity indication Measuring method: Dual-slop integrating A/D converter system. Sampling rate: Approx. 3times/second Over range indication: “ OL” Low battery displays. Operating environment: Temperature (0 ~ 40)℃, humidity<80%RH. Power: Double, standard 9 volt battery. Dimension: 190mm×88.5mm ×27.5mm. Accessories: Operation manual ,holster, gift box, TP01 thermocouple, test leads, 9V battery.

Product Description HL HRC HRB LEEB Hand Held Hardness Tester 600 Groups Data Memory High-End Model, 3 Years Warranty, Portable Hardness Tester Functions & Features ● High quality and precision. ● Automatically identify 7 types of Impact devices for special application. ● Freely switch to hardness scales HRA, HRB, HRC, HV, HB, HS, HL. ● Direct calibration on HL, HRC, HB. ● PC Software for data transmission, analysis, and measurement reports printing. ● Test at any angle, even upside down. ● Large LCD screen with back-light, showing all functions and parameters. ● Upper and lower limit and sound alarm. ● Conversion to tensile strength (U.T.S). ● 3 years warranty and life-long services. Measuring Materials ● 10 types of metals: steel and cast steel, alloy tool steel, stainless steel, gray cast iron, nodular cast iron, cast aluminum alloy, copper zinc alloys, copper and tin alloy, copper, forged steel. Technical Parameters Model Uee910 Measuring Range (170-960)HLD,(17.9-69.5)HRC,(19-683)HB,(80-104 , 2)HV,(30.6-102.6)HS, (13.5-101.7)HRB, (59.1-88)HRA Hardness parameter HL, HRC,HRB, HRA, HS, HB, HV Accuracy ±6HLD Memory 600 groups PC Connection Available Battery 2*AA Operating Temperature -20℃~+60℃ Dimensions 163×78×33mm Weight 240g Standard Configuration Main unit, Impact Device type D, Calibration block, Small supporting ring, USB cable, Software, Backup accessories(Impact ball*1, Cable*1, Spanner *1), Cleaning brush, Operation manual, Certificate. Optional Accessories Optional Impact Devices(D,DC,DL,D+15,G,C,E), Shaped support rings, Testing blocks

JHD PLCCENTER IMPORT & EXPORT CO., LIMITED Add : Room252 NO38 Tianhuroad,SiMingDistrict,XiaMen City,China QQ :2392596973 Post Code : 361001 Email : kim_jhd1688@163.com sarahjld1688@163.com  W , hats:15759861556 Web : www.jld-electronics.com 1769-OB , 32 1769OB32 1771-P5E 1771p5e 1756-L62  1756L62  1756-EN2T  1756EN2T 1747-L552 1747L552 1747-L553 1747L553 1771-IXE  1771IXE 1794-IT8  1794IT8 1763-L16AWA   1763L16AWA 1769-OW16   1769OW16   1764- , LSP  1764LSP 1756-RM  1756RM  1756-CN2R  1756CN2R 1747-L553  1747L553  1756-OF8 1756OF8 1756-L65 1756L65 1756-RM 1756RM JHD PLCCENTER IMPORT & EXPORT CO., LIMITED Add : Room252 NO38 Tianhuroad,SiMingDistrict,XiaMen City,China QQ :2392596973 Post Code : 361001 Email : kim_jhd1688@163.com sarahjld1688@163.com  W , hats:15759861556 Web : www.jld-electronics.com

Minimum Order: 1 bags