Others & Excess Inventory

The bare board test probe is used for bare board (blank version) testing. To check the operation of a PCB circuit, the test probe is generally applied with the receptacle as the conduction confirmation and inspection of a circuit substrate to examine the fixture, analyze the completeness of the circuit, and inspect specification requirements of the circuit footprint, to ensure proper function of various circuits on PCBs. Specification: 1. Recommended min. center: 1.27 (.050") 2. Full travel: 2.54 (0.1") 3. Current rating: 1.5A 4. Contact resistance: 70mΩ 5. Spring force: 30g / 60g / 80g / 120g Materials and finishes: 1. Plunger: Sk4 / PhBr / NI plated 2. Barrel: Phosphor bronze, Gold plated 3. Spring: Stainless Steel

Optical laborers select high-quality optical glasses, including N-BK7, Fused Silica and sapphire. Through manual and precision instrument processing, optical domes for harsh environments are produced. Optical glass domes are corrosion resistant and high-pressure resistant. They are often used in underwater photography and underwater detection, meterological station measurement and military missiles, as a protective cover to protect sensitive sensors and detection equipment. N-BK7 Domes N-BK7 has good transmittance (400nm-1550nm) in the visible and near-infrared spectrum. N-BK7 is a common optical material with low cost and high performance. The refractive index is highly consistent. There are fewer bubbles and streaks in N-BK7. N-BK7 domes are used for solar pyrgeometers to protect the detector from rain and snow. Besides, they prevent harsh environments from affecting the sensitivity of the detector. In addition to the commonly used N-BK7 Domes, RZ Optics Co., Ltd. also produces optical domes made of fused silica and sapphire. Fused Silica Domes Fused silica is often used in the ultraviolet spectrum, between 185-2500nm, with good transmittance. Fused silica has high chemical purity, corrosion resistance and high mechanical properties. It withstands temperature changes. It is not easy to deliquesce. Fused silica domes are used as a protective cover for underwater detectors and underwater robots to protect their optical imaging systems. In addition, high-precision optical domes hardly affect the imaging effect of underwater detection equipment. Sapphire Domes Sapphire is a stable infrared material, anti-corrosion and anti-deliquesce. Under the same thickness, the performance of sapphire is better than optical glass and quartz glass, but the price is slightly more expensive. Sapphire domes are often used as a protective cover for deep-sea optical imaging systems and guided missiles due to its stable chemical properties, strong pressure resistance and better capabilities of transmission. RZ Optics Co., Ltd. produces custom optical glass domes, according to your requirements. We strictly control the parameters of optical glass domes to ensure the precise design of each batch of custom optical glass domes. For more information, please contact us.

RZ Optics Co., Ltd. provides custom optical domes that meet applications of customers. Our company produces optical domes made of optical glass, quartz glass, sapphire and silicon. Our company specializes in processing optical domes for deep-sea exploration, underwater exploration and meteorological exploration. Optical domes produced by our company are used as a window for underwater cameras and underwater robots. They are resistant to seawater corrosion and high pressure. They are also used for meteorological pyrgeometers as protective covers. RZ Optics Co., Ltd. provides optical glass domes with commercial quality and high precision quality, including N-BK7 domes, Fused Silica domes, Sapphire domes and Silicon domes. The diameter of custom optical glass domes can be 15-280mm. The highest accuracy of concentricity can be less than 0.02mm. The highest accuracy of surface quality can be 40-20. How can you get custom optical domes? Please send us design drawings or custom parameters, including diameter, optical material and surface quality. Don't forget to add the requirement of quantities and lead time. Of course, the simplest way is direct to contact us for more information. N-BK7 Domes N-BK7 has good transmittance (400nm-1550nm) in the visible and near-infrared spectrum. N-BK7 is a common optical material with low cost and high performance. The refractive index is highly consistent. There are fewer bubbles and streaks in N-BK7. N-BK7 domes are used for solar pyrgeometers to protect the detector from rain and snow. Besides, they prevent harsh environments from affecting the sensitivity of the detector. Fused Silica Domes Fused silica is often used in the ultraviolet spectrum, between 185-2500nm, with good transmittance. Fused silica has high chemical purity, corrosion resistance and high mechanical properties. It withstands temperature changes. It is not easy to deliquesce. Fused silica domes are used as a protective cover for underwater detectors and underwater robots to protect their optical imaging systems. In addition, high-precision optical domes hardly affect the imaging effect of underwater detection equipment.  Sapphire Domes Sapphire is a stable infrared material, anti-corrosion and anti-deliquesce. Under the same thickness, the performance of sapphire is better than optical glass and quartz glass, but the price is slightly more expensive. Sapphire domes are often used as a protective cover for deep-sea optical imaging systems and guided missiles due to its stable chemical properties, strong pressure resistance and better capabilities of transmission.

The biconvex lens is a convergent lens with two outwardly curved surfaces, which are symmetrical. Its radius of curvature is equal. The spherical aberration, coma and distortion of biconvex lenses reach the minimum. In addition to controlling laser beams in lasers, biconvex lenses are also used for optical imaging systems or other optical instruments. N-BK7 Bi-Convex Lenses N-BK7 (Equivalent Material CDGM H-K9L) is crown glass with a transmission range of visible light and near-infrared spectrum (350nm-2000nm). N-BK7 possesses excellent optical, mechanical and chemical properties and is cost- effective. N-BK7 double convex lenses are often used in various optical imaging systems. Fused Silica Bi-Convex Lenses Between 185-2500nm, fused silica biconvex lenses have good transmittance. Fused silica has stable chemical properties, high-temperature resistance, low laser damage threshold. It is suitable for laser optical systems. Silicon Bi-Convex Lenses Silicon has metallic luster and is blocked in the visible light band. It has good transmittance in the infrared band (3-5μm). As a commonly used infrared optical material, silicon has high refractive index and small dispersion. Silicon lenses are widely used in infrared missile optical systems.

Plano-convex lenses are positive focal length elements with one spherical surface and one flat surface. These lenses are designed for infinite conjugate (parallel light) use or simple imaging in non-critical applications. These optics are ideal for general purpose focusing elements. Our lenses are ideal for a variety of applications, from industrial, robotics, pharmaceutical to defense. Esco manufactures plano-convex lenses using S1-UV grade fused silica, G1 fused silica, commercial grade and BK7 optical glass. Each optic is pitch polished to provide good surface quality and excellent low-cost imaging performance for a wide range of light sources. When plano convex lenses are used for laser cutting, they are best suited for high-turnover cutting applications and when cutting thick materials. In these cases, the plano-convex lens provides a larger cut width, which allows the laser's oxygen-assisted access to cut and aid in the cut. Plano convex lenses also provide greater depth of field, which helps create tapered edges.

Plano-Concave Lenses have edges that are thicker than the center and flat on one side. Plano-concave lenses are used to expand a light beam or increase the focal length in an optical system. They are commonly used for beam expansion of high peak power pulsed lasers. The beam incident on the concave surface will be focused to a point outside the instrument. Unwanted air heating and ionization at the focal point may accompany mode disruption or material damage. To avoid this problem, the input lens should be inverted so that the concave surface is not facing the parallel beam. Material selection: optical glass, laser crystal, fused silica, anti- radiation glass, infrared and ultraviolet materials, metal materials Strict dimensional control standards custom coating Wide selection of RZ spherical lenses made of N-BK7, UVFS or CaF2 optical materials, spherical lenses made of N-BK7, UVFS or S-LAH64 optical materials, cylinders and cones (shafts) made of N-BK7 and UVFS cone) lens. The lens forms are plano-convex, plano-concave, double-convex, double- concave, plano-convex cylinder and plano-concave cylinder. Focal lengths vary from -5000 to +10000 mm. Other specific materials, sizes and anti-reflective (AR) coated lenses are available upon request. Factory Standard Shape: Plano-Concave Diameter Tolerance: ± 0.05mm Thickness Tolerance: ± 0.05mm Radius: ± 0.3% Focal Length Tolerance: ± 1% Surface Quality: 40-20 Scratch-Dig(After Coating) Surface Flatness: λ/4 @633 nm Centration: < 3 arc minutes Clear Aperture: > 95% of central dimension

With 10 + Years of Experience in The Production of Safety Protection Products. High Adsorption Capacity, 10-25 Times of Self Weight. Can Be Reused to Save Money. Absorbent Various Oil, Only Absorb Oil but Not Water, Fast Oil Absorbent, Good oil retention,Reused, Melt Blown Absorbent Material, Keep Floating Water Surface After Absorbing, Oil Spill Absorbent Control, Apply to Land, Water Surface.

Jiangsu Bangdeya New Material Technology Co.,Ltd. whatsapp: + 85259876550 Email :bangdeya2@bangdeya.com Wickr:sarahwickrr We not only have a complete range of products,but also have rich experience,strong strength,excellent quality and competitive prices for chemical raw materials. Payment: TT,Western Union or BTC ADDRESS Safest delivery by Fedex ,UPS ,DHL.etc. Sample is available for test first. Looking forward to your early reply. hot product Bmk oil cas20320-59-6 Pmk oil cas28578-16-7 Tadalafil cas171596-29-5 Sildenafil citrate cas171599-83-0 N-Isopropylbenzylamine CAS 102-97-6 Pregabalin cas148553-50-8 Dimethocaine CAS94-15-5 Paracetamol Powder CAS 103-90-2 Bromazolam cas71368-80-4 Cyclohexanone CAS 2079878-75-2 Protonitazene cas119276-01-6 Metonitazene cas 14680-51-4 BMK Glycidic Acid cas5449-12-7 Xylazine CAS7361-61-7

Minimum Order: 1 bags

Common name 2-Bromo-4'-methylpropiophenone English name 2-Bromo-4'- methylpropiophenone CAS No. 1451-82-7 Molecular Weight 227.098 Density 1.4±0.1 g/cm3 Boiling Point 273.2±15.0 °C at 760 mmHg Molecular formula C10H11BrO Melting point 75-77ºC MSDS N/A Flash point 58.6±7.7 °C

Minimum Order: 10 long tons

Solar Light

Paper Machine Clothing Single Layer Forming Fabric Description The single-layer forming fabric is the simplest forming fabric. They are woven in 4-shed(Provides good stretch and drainage properties. Small fiber loss and good sheet release.), 5-shed(Provides better stretch and drainage properties than 4-shed. Retention can be improved by increasing weft yarns. Primarily used on tissue machines.), and 8-shed for different applications. In flat woven type fabric, the warp, during weaving, is composed of yarn which is referred to as MD yarn. In order to make endless loops, fabrics are joined by connecting the warp yarn at the end of each fabric. FILCON uses automated seaming machines for connecting fabrics. According to their weaving shed, single-layer forming fabrics could be used for the manufacture of kraft papers, tissue papers, writing & printing papers, and so on. Forming Fabrics Feature: 4-shed single layer forming fabric. Display excellent stretch, drainage and anti-wear property. 5-shed single layer forming fabric. Better stretch, drainage features and ideal for tissue machines. 8-shed single layer forming fabric. With enhanced retention, excellent drainage, and ease to clean.

Double Layer BOM Press Felts Description Paper Machine Clothing Double Layer Press Felts include a 1+1 composite structure and a double layer of MD yarn structure. The 1+1 composite structure consists of two-layer base meshes of different thicknesses. Both of these base meshes can be changed in construction and sizes to suit the requirements of different paper machines. Double layer felts have the features of high press resistance, good flexibility, permeability and size stability, less elongation, excellent tensile strength. The felts are also resistant to vacuum marks, blind hole marks, groove marks, etc. Press Felts Application: Applied to press types: groove press, vacuum suction press, multi-press, large diameter nip-roll press to meet the production of high-grade printing paper, newsprint, technical paper, packaging paper, high-grade paper board etc. Paper machine: Multicylinder, super forming, superposition wire, nip wire paper making for different kinds of paper machine’s press felt and forming felt. More about our company PFM Screen, please contact

Paper Machine Clothing Single Layer BOM Press Felts Description Single Layer BOM Felt is made up of single base layer mesh fabric and fiber layer. The base layer is woven from synthetic mono-filament or multi-filament. The fiber layer consists of the various lap of fiber web and different diameters of fiber for better drainage and fiber support index. The structure is designed base on different paper machines, press types and different papers. It has good quality properties such as less elongation, easy to wash, no-mark on paper, long-life performance and can be used in various paper machines to produce different kinds of paper. Feature: Single-layer base fabric The most basic design Less elongation Easy to clean No-mark on the paper surface Long-life performance Press felts play an important role in removing moisture from the paper web after the forming section, while imparting smoothness and transporting it to the dryer section. To this end, press felts need to provide the following functions: water removal, smoothing and running. In recent years, larger and faster paper machines require press felts of higher consistency and quality.

Triple Layer Forming Fabric Description Triple-layer forming fabrics have two independent single-layer fabrics bound together by separated yarns. On the forming side, the yarns have a small diameter to increase the support index. On the wear side, cross-direction yarns have a large diameter to improve the fabric life. The wear side is made with a coarse mesh to improve stability and wear resistance. The paper side is made with very fine yarns on the surface to optimize the sheet forming performance. This modified design delivers enhanced stability in the cross-machine direction thanks to its three-ply weft structure. Furthermore, improved drainage is guaranteed because of its increased three-dimensional space. Paper Machine Clothing Triple Layer Forming Fabric Feature: Better support and fixation, while reducing line marks. Better drainage performance Better stability and abrasion resistance. Longer service life