Other General Hardware

0.9mm diameter,Unlimited height,the black tie wire Cutting wire is to cut off various metal wires such as bright iron wire, fired wire, electro-galvanized wire, hot-dip galvanized wire, plastic-coated iron wire, painted iron wire, etc. according to customer requirements. Golden Deer Cutting wire is made of annealed wire, galvanized wire, coated wire, paint wire and other wire, according to customer requirements straighten the cut after the cut. Products with easy to transport, easy to use features. Widely used in the construction industry, handicrafts, daily civilian and other fields. According to the specific requirements of customers,processing customized all kinds of special specifications products. black tie wire Description 1.Cut wire is a kind of tie wire made with iron wire cutting to certain sizes after being straightened. It is made with galvanized iron wire straightened then cut into pieces of various length according to your requirement.

Golden Deer Bearings are a crucial tribological component of many types of machinery and exist in a variety of forms and shapes. They can be defined as a component that supports/permits only a specific type of motion (restriction of degrees of freedom) in a system that may be under static or dynamic loading. The main purpose of bearings is to prevent direct metal to metal contact between two elements that are in relative motion. This prevents friction, heat generation and ultimately, the wear and tear of parts. It also reduces energy consumption as sliding motion is replaced with low friction rolling. They also transmit the load of the rotating element to the housing. This load may be radial, axial, or a combination of both. A bearing also restricts freedom of movement of moving parts to predefined directions as discussed above.

Golden Deer Top support, the building is used for the bottom and top supports of the scaffolding. Both the top and bottom supports are adjustable for the integrity of the screw. The screw consists of a screw, a nut, a ball, a preloader, a commutator and a dust protection device. Its function is to convert rotary motion into linear motion, which is a further extension and development of Akem screw. An important aspect of this development is the change from sliding to rolling motion of the bearings. Top support Description The upright pole and the crossbar connecting the upright pole are connected by a roulette wheel at the position where the upright pole is connected to the crossbar, with a jack on the roulette wheel and a crossbar plug perpendicular to the crossbar at both ends of the crossbar. The crossbar plugs and the wheels connect the crossbar to the riser bar in a way that is not only very stable but also easy to install. When erecting wheeled scaffolding, the crossbar plugs can be inserted directly into the sockets of the wheel, and the connection of the plugs and sockets is self-locking, making it more stable during construction. The connection structure of the plugs and sockets is self-locking, making it more stable during construction.

1.5kg,1.6kg ,1.7kg ,2kg Scaffolding fasteners, Used for fixing steel pipe scaffold with outer diameter of 48mm Scaffolding fasteners Description considerably longer than is need when the nut has been tightened. This excess length is required to allow the clamp half to be opened even while the nut is retained on the screw. To do so, the screw and nut arrangement engages a slot in the clamp half. This excess length of screw then protrudes into the area around the scaffolding system where it can cause a considerable hazard to people and equipment. For example, an operative walking pass the clamp can snag a part of their body or a part of their equipment on the screw, causing direct injury or indirect injury, perhaps when a loose strap catches on the screw and pulls the operative off balance, or causes an item of equipment to fall towards the ground where it could hit another operative but also at least damage the equipment and other equipment/supplies on the ground. A falling operative could hit one of these clamps in particular the protruding screw and cause considerable harm to him/herself. Furthermore, over time the end of the screw can become damaged and sharp edges or burrs can be generated which further increase the harm that this excess of screw length can inflict on an operative. A member of the public walking past or underneath a scaffolding assembly can inadvertently catch himself on the protruding screw and the responsible authority (operator) must consequently spend a considerable amount of time assessing and mitigating the hazards caused by scaffolding clamps where the public may need to come close to scaffolding. A system which mitigates such a hazard from the start may therefore confer considerable time savings and hazard-related savings on the operator.

Steel formwork is used for concrete pouring. In addition to steel formwork, there are wooden formwork, plywood formwork, etc.      Golden Deer Steel formwork is widely used in construction projects due to its multiple use and beautiful appearance of concrete pouring. Steel formwork Description 1. Steel formwork:Golden Deer Formwork is a mould used to receive concrete in plastic form. The template is a temporary structure, so it is usually not displayed on the drawing. Formwork for beams and floors 2. Definition: It is an artificial support provided under and around precast or cast-in-place concrete works. The template is usually made of steel or wood. Formwork construction and casting are crucial in the concrete industry. It bears a lot of specific costs. 3. The quality of the template: Waterproof, it should be sturdy and reusable, and the contact surface should be even, according to the size of the component. 4. Types of templates: There are two main types of templates: steel template, wooden template, steel template Steel plate angle iron, tee iron, wooden template made of props, wooden slats, ledger, sheet