Metal Processing Machinery

Refine Flux smelts aluminum and aluminum alloys, and has a better degassing and impurity removal effect, which can make the hydrogen content in the aluminum alloy melt lower, and can more effectively reduce the burning loss of the metal. At the same time, the refining agent has a certain heating effect, which makes the hot slag recovery more convenient and the recovery rate is higher. Contact sales@adtechamm.com or visit www.adtechamm.com to BUY GRAIN REFINING FLUX. In order to manufacture high-quality aluminum or aluminum alloy profiles, the raw materials of aluminum or aluminum alloy profiles must be refined (refined), which requires a good Refine Flux. Refine Flux generally uses inert gas as a carrier to pass into the aluminum and aluminum alloy melt for degassing and impurity removal. If Refine Flux is used improperly, the following undesirable conditions will occur For example: poor separation of aluminum slag, poor degassing effect, excessive heating effect, increased aluminum burning loss, or no heating effect, resulting in the inability to recover hot slag. In general, before degassing and impurity removal of aluminum and aluminum alloy melts, the H (hydrogen) content is often more than 0.30ml/100gAl. If the raw materials are not good enough, the H content may even exceed 0.40ml/100gAl. Good quality refining The agent can divide the H content of the aluminum melt in the furnace to the level of 0.18ml/100gAl. When the flux is added to the aluminum alloy melt, it melts into flux droplets. Since the specific gravity of the flux is smaller than that of the melt, the flux droplets float in the melt. In the process of floating, it will meet the particles of non-metallic inclusions in the melt. Since the surface tension of the flux at the interface of the non-metallic inclusions is small, the flux can wet the non-metallic inclusions and make them adsorb to the flux droplets. The flux has a large surface tension at the interface of the molten aluminum and does not infiltrate, so the flux can surface with the adsorbed non-metallic inclusions under the action of the difference in specific gravity, and then be removed by slagging. This kind of slagging is generally called Slagging for flotation. Refine Flux has the following characteristics 1.It has a certain dissolving ability for oxides. 2.Enough to increase the fluidity of molten flux. 3. It can effectively remove the oxide film on the surface of the melt and improve the degassing effect. 4. Increase the surface tension of the mixed molten salt, spheroidize the molten salt that has adsorbed oxides, facilitate separation from the melt, reduce the loss caused by the solid molten slag entrapped in aluminum, and increase the surface tension of the flux-melt , Accelerate the process of volume adsorption inclusion.

Minimum Order: 1 bags

Refine Flux smelts aluminum and aluminum alloys, and has a better degassing and impurity removal effect, which can make the hydrogen content in the aluminum alloy melt lower, and can more effectively reduce the burning loss of the metal. At the same time, the refining agent has a certain heating effect, which makes the hot slag recovery more convenient and the recovery rate is higher. Contact sales@adtechamm.com or visit www.adtechamm.com to BUY GRAIN REFINING FLUX. In order to manufacture high-quality aluminum or aluminum alloy profiles, the raw materials of aluminum or aluminum alloy profiles must be refined (refined), which requires a good Refine Flux. Refine Flux generally uses inert gas as a carrier to pass into the aluminum and aluminum alloy melt for degassing and impurity removal. If Refine Flux is used improperly, the following undesirable conditions will occur For example: poor separation of aluminum slag, poor degassing effect, excessive heating effect, increased aluminum burning loss, or no heating effect, resulting in the inability to recover hot slag. In general, before degassing and impurity removal of aluminum and aluminum alloy melts, the H (hydrogen) content is often more than 0.30ml/100gAl. If the raw materials are not good enough, the H content may even exceed 0.40ml/100gAl. Good quality refining The agent can divide the H content of the aluminum melt in the furnace to the level of 0.18ml/100gAl. When the flux is added to the aluminum alloy melt, it melts into flux droplets. Since the specific gravity of the flux is smaller than that of the melt, the flux droplets float in the melt. In the process of floating, it will meet the particles of non-metallic inclusions in the melt. Since the surface tension of the flux at the interface of the non-metallic inclusions is small, the flux can wet the non-metallic inclusions and make them adsorb to the flux droplets. The flux has a large surface tension at the interface of the molten aluminum and does not infiltrate, so the flux can surface with the adsorbed non-metallic inclusions under the action of the difference in specific gravity, and then be removed by slagging. This kind of slagging is generally called Slagging for flotation. Refine Flux has the following characteristics 1.It has a certain dissolving ability for oxides. 2.Enough to increase the fluidity of molten flux. 3. It can effectively remove the oxide film on the surface of the melt and improve the degassing effect. 4. Increase the surface tension of the mixed molten salt, spheroidize the molten salt that has adsorbed oxides, facilitate separation from the melt, reduce the loss caused by the solid molten slag entrapped in aluminum, and increase the surface tension of the flux-melt , Accelerate the process of volume adsorption inclusion.

Minimum Order: 1 bags

Refine Flux smelts aluminum and aluminum alloys, and has a better degassing and impurity removal effect, which can make the hydrogen content in the aluminum alloy melt lower, and can more effectively reduce the burning loss of the metal. At the same time, the refining agent has a certain heating effect, which makes the hot slag recovery more convenient and the recovery rate is higher. Contact sales@adtechamm.com or visit www.adtechamm.com to BUY GRAIN REFINING FLUX. In order to manufacture high-quality aluminum or aluminum alloy profiles, the raw materials of aluminum or aluminum alloy profiles must be refined (refined), which requires a good Refine Flux. Refine Flux generally uses inert gas as a carrier to pass into the aluminum and aluminum alloy melt for degassing and impurity removal. If Refine Flux is used improperly, the following undesirable conditions will occur For example: poor separation of aluminum slag, poor degassing effect, excessive heating effect, increased aluminum burning loss, or no heating effect, resulting in the inability to recover hot slag. In general, before degassing and impurity removal of aluminum and aluminum alloy melts, the H (hydrogen) content is often more than 0.30ml/100gAl. If the raw materials are not good enough, the H content may even exceed 0.40ml/100gAl. Good quality refining The agent can divide the H content of the aluminum melt in the furnace to the level of 0.18ml/100gAl. When the flux is added to the aluminum alloy melt, it melts into flux droplets. Since the specific gravity of the flux is smaller than that of the melt, the flux droplets float in the melt. In the process of floating, it will meet the particles of non-metallic inclusions in the melt. Since the surface tension of the flux at the interface of the non-metallic inclusions is small, the flux can wet the non-metallic inclusions and make them adsorb to the flux droplets. The flux has a large surface tension at the interface of the molten aluminum and does not infiltrate, so the flux can surface with the adsorbed non-metallic inclusions under the action of the difference in specific gravity, and then be removed by slagging. This kind of slagging is generally called Slagging for flotation. Refine Flux has the following characteristics 1.It has a certain dissolving ability for oxides. 2.Enough to increase the fluidity of molten flux. 3. It can effectively remove the oxide film on the surface of the melt and improve the degassing effect. 4. Increase the surface tension of the mixed molten salt, spheroidize the molten salt that has adsorbed oxides, facilitate separation from the melt, reduce the loss caused by the solid molten slag entrapped in aluminum, and increase the surface tension of the flux-melt , Accelerate the process of volume adsorption inclusion.

Minimum Order: 1 bags

sales@adtechamm.com provides Ceramic Foam Filter, Tap Out Cone, Degassing Unit, CFF Unit, Castertip, Launder, hop-top casting for molten aluminum. www.adtechamm.com Ceramic foam filter Dimension 660x660x50(26 inch) 584x584x50(23 inch) 508x508x50(20 inch) 432x432x50(17 inch) 381x381x50(15 inch) 305x305x50(12 inch) 228x228x50(9 inch) 178x178x50(7 inch) Ceramic foam filter Pore Size（PPI）:10/20/30/40/50/60 30ppi 40ppi Foundry Filter is the most commonly used ceramic foam filter in the aluminum casting industry. Ordinary aluminum casting usually uses 10-40ppi ceramic filter plates. Aviation and high-quality aluminum materials usually use 30-60ppi ceramic filter plates. Ceramic foam filters are basically divided into 6 pore sizes: 10PPI, 15PPI, 20PPI, 25PPI, 30PPI, and 40PPI. The larger the number, the smaller the aperture. But in actual practice, the four types of 10PPI 20PPI 30PP 40PPI can meet the needs of customers. Aperture selection 1. The casting: 10～25ppi 2. Semi-continuous casting: 30～60ppi 3. High-quality aluminum or sheet: 50～60ppi 4. Continuous casting and rolling: 50～60p ADTECH keeps focusing on the manufacture of the metallurgical material. ADTECH is one pioneer following by the International Enterprise, who keeps focusing on the manufacture of the metallurgical material. 1.Ceramic Foam Filter 2.Degassing Unit 3.Filter Box 4.Hot-top casting series 5.Roll casting nozzle 6.Flux series 7.Other Metallurgical Material SALES@ADTECHAMM.COM

Minimum Order: 1 bags

Steel Enclosure Box Making Process Electrical panels forming and bending machine https://www.superdamc.com Un , coiler→ Straightening→Servo feeder→Hydraulic device→ Guide device → Roll forming machine →Bending device Distribution box production line technology explaination This production line is equipment for production of distribution boxes. The strip coil to be processed is manually placed on the uncoiler, and then corrected and tensioned. After leveling, it enters the hydraulic pre-punching and punching notch, and is sent to the forming machine by the guide device to form. Under the frictional damping action of the forming roller and pressure roller, after entering the bending part at a linear speed of 0-13m, the box is cut and bent as required, and then manually packed away. This production line produces 2-3 enclosures per minute. the production box quantity speed according to different product specifications.

Minimum Order: 1 bags

Electrical Cabinet 9 Fold Profiles Roll Forming Machine Automaitc electric factory using cabinet frame roll forming machine for electric cabinet 9 fold rack, electronic box pole, metal case frame which using in switchgear system, server case, low voltage panel building, control cabinet electrical instruments etc. Electronic control panel 9 bend frame production line process 2 in 1 Uncoiler Straightening→servo feeder→punch → Guide device → roll forming machine → Roller welding →shear device (including knife)→ finished product rack

Minimum Order: 1 bags

Handrail roll forming machine for differenct handrail shapes such as triangle tube, mushroom tube, bread tube etc handrail using. Size for 50mm, 60mm, 75mm round tube forming as different special tube production. Machine size:3.3*1.3*1m Machine Weight:1280kgs Machine power: 7.5kw

Minimum Order: 1 bags

Automatic flush mount electrical enclosure roll forming machine for making wall mounted switchboard enclosures, fetwork box, cirduit breaker enclosures, network enclosure. Flush mount electrical enclosure machine making dimension. Push bottom box length is adjustable from 200-600mm, the width is 190mm, and the depth is 80mm. The actual cross-section of the product provided by the customer. Electrical box roll forming machine for production different type metal enclosure, such as distribution box, flush mount network enclosure, multimedia signal box. Wall mount circuit breaker enclosure production line parameters of the forming equipment. a. Power supply: 380V/50HZ/3PH, can customized as per user country. b. Installed capacity: about 31kw. c.Forming speed: 0-13m/mind. d.Shearing method: Servo front shear e. Drive motor: Unwinder motor 4KW. leveling motor 2.2KW. hydraulic punching cutting and hydraulic tensioning motor (two sets) 11KW+7.5KW. forming main engine 5.5KW. servo motor 2KW f. Floor area (approx.): length 24m × width 3m (host specification 7mX1.7m) g Production line direction: from left to right (on the console facing the unit). h. Equipment color: (customer selection) i. Superda steel box equipment design can meet 12 hours of continuous production j. Operating environment 1: Power supply voltage: 380V ± 10% / three-phase four-wire,frequency: 50HZ Total power: about 31KW2: Environment Temperature: 0-40 ° C, relative humidity: 60-95% RH. https://www.superdamc.com

Minimum Order: 1 bags

ZD1210 pneumatic(hydraulic) multi-contact finger internal compaction microseism molding machine introduction: the machine for a variety of foundry sand molding clay. the machine can be used stand-along,but also the composition of the use of mechanized assembly line,composed of semi-automatic production line can also be used. using the multi-contact pneumatic compaction,moderate pressure,contact the number of 48,suitable for modeling complex model. the local contact pressure when a shock compacted sand,and together with the shock table,the high hardness and uniform sand.this machine adopts pneumatic spring fully buffered microseism body,it is no special requirement on the ground. from the machine axis synchronous mode using link structure governor oil pressure,since the synchronization mode,and speed control easily.

Minimum Order: 1 bags

BT225 The BT225 is great for larger jobs and light industrial work. It is the most popular machine for blasting business operators. It holds up to 38 kg of water and 45.4 kg of abrasive which allows up to ~1 hour of continuous blast time. This machine runs perfectly with a 185 CFM air compressor.

Minimum Order: 1 bags

cookware sand molding machine also called Jolt squeeze molding machine for green sand casting production.This green sand cookware jolt squeeze molding casting machine can be operated for manual casting foundry and also adapts to simple casting line. Pneumatic cranes can be used to hang up and transfer finished molds.

Minimum Order: 1 bags

The single arm resin sand mixer has short structure and small working area.It is only suitable for small sand box molding and small casting volume. Electric adopts imported PLC control, stable and reliable work, to achieve automatic production. Feature: 1.agglomera , nt system adopt electric variable diaphragm pump,light weight,compact size,the flow is stable and reliable. 2.sand mixed system of uniform,effectively ensure the shape(core system) quality. 3.sand short time,without a head,tail sand,down the back of clean material.wide-open cage-type wall of sand up for leaf clean-up or adjustment,to facilitate the operation and maintenance. 4. mixer entrance need to be configured according to the production of the proportion of old and new sand regulator,accurate control of the old and the new volume of sand and the proportion of sand,sand transfer process can be a good proportion of pre-selection and change. Description: 1. Mixing outputs range from 3T per hour to 10T per hour, ideal for smaller foundries and catering for a number of individual customer requirements. 2. The split tube mixing trough and removable shaft ensure the system is easily maintained for greater longevity. 3. The pivotal mixer can be supplied with either the BASIC panel which excludes a PLC and has manually adjustable pumps. Or we can

Minimum Order: 1 bags

Q69 steel plate,section shot blast clean-up machine: Designed and produced by adopting the advantages of similar products from both within the country and abroad.the rusting cleaning parts(shot blast cleaning)adopts high-efficiency blast wheel and full shutter type shot sand separator.the aweeping machine adopts specially made high-strength nylon rolling brush and high-pressure ventilator.the preheating and drying part may adopt various heating methods.the paint spraying parts adopt high-pressure airless spraying method.the complete set of equipment is controlled by PLC,and is the large-size complete equipment of international advance level. it is mainly used for surface treatment(namely preheating,rust removal,paint spraying and drying) of steel plate and various structural sections,as well as for cleaning and strenghening of metal structure parts.

Minimum Order: 1 bags

Q35 series hook type shot blasting machine: Turntable Shot Blasting Machine Q35 Turntable shot blasting machine is suitable for surface strengthening of compressed work piece, the work piece is in the turntable and is blasted from vertical direction. Q35 shot blast machine is suitable for surface rust removal and strengthening of engine connecting bar, gear, shell cover wall, clutch friction part. Choose our turntable shot blasting machine, for it has advantages of high productivity, good sealing effect, compact composition and made using high technology. You can use this machine in casting, car, war factory, any foundry place in your needs . Q3512 turning plate type shot blasting machine/Q3525 turning plate type shot blasting machine

Minimum Order: 1 bags