Tools & Hardware

The insulated centipede type ladder is named after shaped like a centipede,the characteristics are that this ladder is based on the straight rod as the center pillar, and the main mechanical load and insulating strength are carried with the insulated stretching rope,The parallel settings of the insulated crossbar are used as a ladder to run through the rod,they are mainly carry the weight of climbing staff.Compared with the ascending method of conventional live operations, the insulated centipede type ladder can adapt to a variety of terrain operations,it can solve the problems that the power-based operating vehicles and machinery cannot enter the operating area caused by inconvenient road traffic, such as the fields area,hillside area, grass area,etc.This ladder is not highly required for the geographical conditions of the operation site. The weight of this ladder is light, easy to carry, convenient operation.It’s expand the new way to board the power operation. The feature of the product： 1. The trunk is made of high-strength epoxy weaving and pulling insulated tube. It has good insulated performance, high strength, good rigidity and small offset under load. 2. The ladder pedal can be made of circular insulated tube or Reuleaux triangle insulated tube, good insulated performance, high mechanical strength, Reuleaux triangle insulated tube foot stepping on the contact surface, comfortable feet when climbing. 3. Insulated wind rope adopts insulated nylon rope or insulated silk rope, with good insulated performance and high stretch strength。 4. The structure design of the insulated centipede ladder is a segmented plug-in locking type, with a mounting base at the lower end to fix the rod body. Each section of the structure about 3M, and the foot pedal is fixed. It is equipped with a waterproof and moisture-proof insulated bag, which is easy to carry.。 5. This ladder can be equipped with insulated work platform, and staff can stand on the insulated work platform to work, which greatly improves the comfort of the operation。 6. The main insulated tube is yellow, and the ladder pedaling tube is fluorescent green or yellow。

Insulated hook ladder has many applications in high-voltage maintenance, which can position the line workers in the most advantageous working position and carry out line repairs in almost inaccessible places. All hooks are made of tempered steel with a diameter of 26mm and can rotate to best accommodate various angles on the structure. The steel chain is clamped onto the hook to help secure the ladder to the bracket. The crossbar material for both rated ladders is 32mm epoxy glass coated with a sand layer. Features 1. Designed to effectively, position linemen for high-voltage maintenance,make line repairs possible, even in inaccessible places 2. Hooks are formed from 26mm diameter tempered steel, these hooks can be swiveled to best various angles on structure 3. Ladders include hooks and steel chains, the steel chains clip to hooks to assist in securing ladder to support, rung material for both rated ladders are 32mm sand- coated Epoxy fiberglass rod,it has excellent anti slip performance. 4. Length can be customized.

Telescopic fiberglass ladders are widely used for city power line urgent repair ,Substation Inspection and other linemen works.It is the necessary tools for utility,company,hotel,family and so on. 1. The advantage of the telescopic fiberglass ladders Light weight, good insulation performance ,anti slip , corrosion resistant and small package which can put into the car. 3.Safety note: 1.Please inspect the ladder carefully with all the parts in the good condition. 2.Please make sure install the ladder on the hard and flat ground to preventing any dangerous caused by slanting. 3.Please be careful when you use the ladder in the windy day. 4.Please don’t put over weight on the ladder. 5.Please keep the stand on the middle of the ladder to avoid lost balance when you on the ladder. 6.Please don’t move the ladder when the person on it. 9.Please don’t put your hand on the steps when retract the ladder. 10.Please note only one person allowed on the ladder the same time. 11.Please stock the ladder in the dry,ventilate room .

Minimum Order: 1 bags

Main Character： 1.No special tools required for installation, no need crimping operation. 2.Automatic Splice is tension-dependent device that the line must have at least 10% of the rated breaking strength during installation to ensure reliable electrical connection. 3.The current passes through the wire to the metal crucible, flows through the metal crucible to pass the current to the outer casing, and the outer casing transmits the current to the metal crucible, which is transmitted from the metal crucible to the conductor. 4.The loop resistance of the Automatic Splice is not more than 1.1 times the loop resistance of the isometric conductor. The metal crucible can penetrate the residual oxide layer on the surface of the conductor ,so that electrical conductivity is Reliable.

Minimum Order: 1 bags

TID POWER Insulated bypass jumper adopts soft insulated conductor to pass through the support pipe of middle high strength epoxy insulated tube. The clamp design of both ends is suitable for glove operation and insulation rod operation. Insulated by-pass jumper is mainly used for 15kV by-pass operation when temporarily connected to the conductor.

Minimum Order: 1 bags

Insulated jumper wire set is used to bypass work areas during line upgrades and temporary or emergency repairs. 1. Compliant with: ASTM F2321 standard 2. When installing and removing jumper clamps, appropriate rubber insulation must be worn to clear the blockage.

Minimum Order: 1 bags

W Vortex pump is a vane pump. W vortex pump is mainly composed of impeller, pump body and pump cover. Impeller is a disk, the circumference of the blade radial uniform arrangement. The pump body and impeller form a circular flow path, suction inlet and discharge outlet are in the outer circumference of the impeller. There is a clapboard between the suction inlet and the discharge outlet, thereby separating the suction inlet and the discharge outlet. USES: W single-stage direct-connect vortex pump is used for pumping water or other liquids in physical and chemical properties similar to water. Liquid temperature is less than 60. W vortex pump is commonly used in boiler feed water of form a complete set, in shipbuilding, textile, chemical, metallurgy, machinery manufacturing, aquaculture, fixed fire control voltage, heat exchange unit and remote sprinkler irrigation agriculture departments with the wide range of applications. W vortex pump is often used for boiler water supply, in shipbuilding, textile, chemical industry, metallurgy, machinery manufacturing, aquaculture, fixed fire pressure control, heat exchange unit, agricultural remote sprinkler irrigation and other departments . Features: 1. The characteristic curve of the vortex pump is similar to that of the centrifugal pump, but it is less efficient with small flow rate and large head. Vortex pump clearance (that is, the gap between the impeller and the cover plate) can not be too large, otherwise it will significantly reduce the efficiency, so this pump can only transfer relatively pure liquid. 2. The characteristics of small volume and light weight of vortex pump have great advantages in ship installation. 3. Self- suction ability or with the help of simple installation. 4. The head characteristic curve with steep drop, so it is not sensitive to pressure fluctuation in the system.

Minimum Order: 1 bags

ISGB detachable pipeline centrifugal pump: ISGB vertical circulation pump booster pipeline water pump is high-effective and energy-saving and easily disassembled It is used to transfer pure water and other liquids similar. ISGB Pump has the advantages of compact structure and small volume and stable running and easy assembly and maintenance. Pump shaft is provided with independent supporting point to ensure steady running and long performance life. ISGB Vertical pipeline centrifugal booster pump is very easy disassembly.(detachable type) Application: ISGB Series vertical booster centrifugal pump is widely used in industrial and cities’ water supply and drainage, high buildings’ booster water supply, gardens irrigation, fire fighting booster, remote water supply, warming systems, circular booster of cold and hot water in bath rooms as well as in competitions of equipment Pump performance range: Pump material: cast iron or cast steel or stainless steel Flow rate:4 to 1500m3/h Head:5 to 125m Speed:960rpm to 2900rpm Pump caliber: 25mm to 350mm ISGB vertical pipeline booster centrifugal pumps are made of cast iron material and the pumps are mainly used to handle the non-corrosive cold and hot water , IHGB vertical chemical centrifugal pumps are made of stainless steel material and the pumps are used in the fields of petroleum, chemical ,metallurgy, electric power , papermaking , pharmaceuticals , synthetic fiber ,etc. Specification sheet:

Minimum Order: 1 bags

ISG vertical pipeline centrifugal pump is also a single-stage single-suction centrifugal pump, because the design of the vertical structure is also known as the vertical centrifugal pump, this centrifugal pump is designed according to the industry standard performance and size. ISG pump is a new energy-saving pump. It can replace IS type horizontal single-stage pipeline centrifugal pump. ISG pipeline centrifugal pump is suitable for industrial and urban water supply and drainage, but also can be used for agricultural irrigation. ISG pipeline centrifugal pump is used for conveying clean water and liquid with similar properties to water. The temperature of pumped liquids is not more than 80°c. When the temperature of liquids is more than 80°c, the hot water type pipeline centrifugal pump or high- temperature resistant pipeline centrifugal pump can be chosen for the high temperature liquids. ISG pipeline centrifugal pump product features: 1, ISG pipeline centrifugal pump is a vertical structure, the inlet and outlet diameter is the same, and located in the same center line. The pump can be installed in the pipeline like a valve. The pump has the advantages of compact and beautiful appearance, covers a small area, low construction investment, such as when add protective cover onto the motor, the pump can be used outdoor. 2. The impeller is directly mounted on the long shaft of the motor. The axial dimension is short and the structure is compact. 3, vertical single-stage centrifugal pump shaft seal with mechanical seal or mechanical seal combination, the use of imported titanium alloy seal ring, medium high-temperature mechanical seal and the use of hard alloy materials, wear-resistant seal, can effectively extend the service life of mechanical seal. 4. Installation and maintenance of vertical single-stage centrifugal pump is convenient. There is no need to remove the pipeline system. 5. The series of pipeline centrifugal pumps can be used in series or parallel operation according to the requirements of flow rate and head. 6, according to the requirements of pipeline layout, the vertical and horizontal pump installation.

ISW horizontal Monoblock centrifugal pump is designed and made according to ISO2858 Standard as the high efficiency and saving-energy pump 1. ISW horizontal fresh water pump is used for conveying clean water and other liquids with physical and chemical properties similar to clean water. It is suitable for industrial and urban water supply and drainage, pressurized water supply in high-rise buildings, sprinkler irrigation in gardens, pressurized fire fighting, long-distance transportation, heating and ventilation refrigeration cycle, bathroom and other pressurized cold and warm water cycle and supporting equipment. 2, ISWR horizontal hot water pump is widely applicable for hot water transportation in metallurgy, chemical industry, textile, paper and hotels and other boiler etc. for hot water pressurized circulation transmission and urban heating system, ISWR operating temperature T≤120℃. 3, ISWH horizontal chemical pump is used to transport corrosive medium without solid particles,,. Medium viscosity is similar to water. ISWH pump is suitable for petroleum, chemical, metallurgy, power, paper, food, pharmaceutical and synthetic fiber and other sectors. Operating temperature of -20℃ ~ +120℃. 4, ISWY horizontal pipeline oil pump is used for the transportation of gasoline, kerosene, diesel oil and other oil products or flammable, explosive liquid, medium temperature is -20℃ ~ 120℃. 5. IHWB horizontal stainless steel explosion-proof chemical centrifugal pump is suitable for conveying inflammable chemical liquid. 6. ISWD horizontal low speed pump is suitable for occasions where low environmental noise is required. Operating temperature T≤120℃. Features: Hot water circulating pump runs smoothly: the absolute concentricity of the pump shaft and the excellent balance of the impeller ensure smooth operation and no vibration. No leakage: hard alloy seals of different materials ensure no leakage in different media transportation. Low noise: the pump is supported by two low noise bearings runs smoothly, with basically no noise except the weak sound of the motor. Low failure rate: the structure is simple and reasonable, the key parts are equipped with international first-class quality, and the working time of the whole machine is greatly improved. Easy maintenance: replacing the seal, bearing is simple and convenient. Floor space is more economical: the exit can be left, right, up (three directions). It is convenient for pipeline layout and installation and to save space.

Minimum Order: 1 bags

Feature: WATER PUMP PLIERS are commonly used for turning and holding nuts and bolts, gripping irregularly shaped objects, and clamping materials. ◎ Forged chrome vanadium steel and heat treated to give 3 times hardness and toughness. ◎ Push the button for fine adjustment on the opening width up to 50mm. ◎ Serrated jaw design to lead great gripping ability. ◎ Black phosphate coating surface to provide excellent durability and corrosion resistance. ◎ Non-slip plastic handle with ergonomic design. ◎ Made in Taiwan. Quality assurance poducts.

Summary: ZS horizontal stainless- steel single-stage centrifugal pump is a new generation of centrifugal pump, which is made of advanced technologies such as stainless-steel plate stamping, expanding and welding. It can replace traditional IS pump and general corrosion resistant pump. The utility model has the advantages of beautiful appearance, light structure, high efficiency, energy saving, durability, light corrosion resistance, low noise, etc. Operating conditions of horizontal stainless steel single-stage centrifugal pump: Clean, thin, non- flammable and explosive liquid without solid particles and fibers; Liquid with temperature between - 20 ℃ and+100 ℃; High ambient temperature+40 ℃ High altitude: 1000m The high pressure of the system is 10bar. Horizontal stainless steel single-stage centrifugal pump motor: The motor is a fully enclosed, air- cooled two pole standard motor Protection grade: IP55, Insulation grade: F, Standard voltage, 50Hz：single phase × 220V &three phase × 380V Horizontal stainless steel single-stage centrifugal pump application: ZS horizontal stainless- steel single-stage centrifugal pump is a multi-functional product with a wide range of applications. It can transport various media, including water or industrial liquid, and is applicable to different temperature, flow and pressure ranges. Its typical applications mainly include the following aspects: Water supply: filtration, transmission, partition water supply and main pipe pressurization of the water plant; Industrial pressurization: process water system, cleaning system; Industrial liquid transportation: boiler water supply, condensation system, cooling and air conditioning system, machine tool matching, acid and alkali transportation; Water treatment: distillation system or separator, swimming pool, etc; Farmland irrigation, petrochemical industry, medicine and health, etc.

Minimum Order: 1 bags

Double suction centrifugal water pump The working principle of a double suction pump is based on the basic principle of a centrifugal pump Impeller design: The impeller of a double suction pump consists of two back-to-back impellers, which allows liquid to enter from both ends of the impeller simultaneously, thereby increasing the flow rate. The operation of a double suction pump The role of centrifugal force: When the impeller rotates at high speed, the liquid is thrown out of the impeller under the action of centrifugal force, forming a high-pressure area. Formation of Low Pressure Zone: A low-pressure zone is formed at the center of the impeller, where atmospheric pressure continuously draws liquid into the center of the impeller. Circulation process: After the liquid is thrown out, it flows into the pressurized water pipeline through the volute, forming a continuous suction and discharge process. Difference from single suction pump Water inlet method: Double suction pumps inlet water from both ends of the impeller, while single suction pumps inlet water from one end of the impeller. Flow rate: Due to the design of the double suction pump impeller, its flow rate can be doubled under the same impeller outer diameter. Price: Double suction pumps are usually priced higher than single suction pumps due to their complex structural design. Double suction pumps have been widely used in engineering due to their high flow rate and head characteristics. For example, in transportation systems that require a large amount of fluid, double suction pumps can effectively meet the demand, and their horizontally split pump casing design is also easy to inspect and maintain. In addition, the design of the inlet and outlet of the double suction pump in the same direction and perpendicular to the pump shaft is beneficial for the layout and installation of the pump and inlet and outlet pipes.

Minimum Order: 1 bags

Wear resistance Easy to install Support customization Thickened material Diesel engine or electric motor optional This pump is suitable for river dredging, dredging and solidifying embankments, coal mines, power plants, and transporting slurry containing solid particles in mines, with a medium concentration of over 40%. Widely used in sand pumping and hydraulic filling projects Product application scope and usage methods 1. The NB series sand pump is mainly composed of a pump body, impeller, protective plate, pump cover, bracket, and bearing components. 2. The materials of the pump body, impeller, and protective plate can be made of high manganese ductile iron, high chromium alloy, and non-metallic wear-resistant materials. Users can choose it according to their intended use when placing an order. 3. The shaft seal of the pump adopts packing seal, and high-pressure flushing water is added to the packing chamber to ensure the normal operation of the pump. 4. The direction of the pump is counterclockwise when viewed from the inlet, and the outlet of the pump is on the right side of the horizontal direction when viewed from the inlet. If necessary on site, the outlet can be adjusted within a 360 degree range. 5. It has the characteristics of high efficiency, energy saving, wear resistance, corrosion resistance, reliable operation, high head, large flow rate (maximum mixed flow rate can reach 2000-5000 cubic meters/hour), deep pumping depth (up to 30 meters deep), wide transportation distance and applicability. The solid-liquid mixture concentration conveyed can reach 60%. Can be equipped with electric motor or diesel engine drive. Application: Suitable for enterprises such as river, lake, and sea sand extraction, sand blowing and land reclamation, river dredging, dredging and solidifying embankments, sand extraction and selection of iron ore, tailings extraction, coal mining, power plants, and mines to transport media containing solid particles, sand extraction ships for sand extraction, sand loading ships, and land-based relay for long-distance transportation of sediment

Minimum Order: 1 bags