Industrial Machinery & Equipment

Application  Dry walk in environmental chambers are a special type of walk in environmental chamber specially designed for drying or dehumidification applications. These chambers provide controlled conditions to remove moisture from products, materials or samples. Drying Walk in Environmental chamber are ideal for automotive, computer, battery, defense and other industries According to market demand and customer requirements, has extensive experience in battery testing technology, has configured dry walk in test chambers for battery production to meet low humidity, such as 5%R.H -10%R.H. A continuously dry indoor climate is one of the key technologies in the production of high-performance lithium-ion batteries for electric drive. DRYING WALK IN ENVIRONMENTAL CHAMBER STRUCTURE Interior material: SUS # 304 stainless steel plate (1.5 mm thickness ). Exterior material: cold rolled steel, galvanized anti-rust treatment with advanced resin paint coating.If you need more models about our test equipment, please reference our https://www.chamber-testing.com/ Insulation material: German Bayer fire-resistant high-strength PU polyurethane foam insulation material +ultra-fine glass fiber. Heat preservation material: imported rigid rock wool rock wool (CSR 120 k). In addition, in order to prevent glass frosting when running low temperature, we setup a heating wire inside to get it de-frosting. Both sides of chamber are equipped with a test cable port with diameter 100mm, the silicon plug is with high low temperature resistance. Heater: Fin type radiator pipe shaped stainless steel electric heater. Technical Specifications Temperature Range：-70°C to 100°C Dew Point Temperature Range：7℃ to 87℃ Extended Dew Point Conditions： -10℃ Humidity Range：10%～98% RH Humidity Control：±2.5%RH Humidity Uniformity：±1.0 % RH Noise test：≤ 68dB

Application  Benchtop temperature chamber can meet certain quality standards and testing specifications ,for example: Daily necessities, cosmetics, electronic components, and medical products .  Most ideal designed for temperature and humidity testing of small samples and specimens used for research, development and quality control.  This dimension are very cute. customer can fit on a personal desk is the most consideration.If you need more models about our test equipment, please reference our https://www.chamber-testing.com/ Feature: Ou , r JOEO Benchtop Temperature Chamber's window is equipped with an anti-sweat electric heater device to prevent water vapor from condensing and water droplets, and high-brightness PL fluorescent lamps keep the interior of the box illuminated;Rectangular multi-layer glass viewing window, which can be used to observe the test items during the test.  With automatic-water supply system, it is convenient to supplement the water supply of the humidification barrel, and it can be recycled and used automatically. High-quality appearance, the body adopts an arc shape, the surface is treated with matte stripes, and the flat non-reaction handle is adopted, which is easy to operate, safe, and reliable. High quality original compressor circulation system adopts the French “Tecumseh”& Germany "Bitzer" brand, which can effectively remove the lubricating oil between the condenser tube and the capillary tube, and the whole series adopts environmentally friendly refrigerants (R23, R404, R507). Double-layer insulation of ess chamber door is tight and airtight, which can effectively isolate internal temperature leakage.  Built-in moving pulley is easy to move and place and has a strong positioning screw to fix the position. Controller has multi-segment program editing and temperature, and humidity can do fast (OUICK) or slope (SLOP) control. Self-developing controller system adopts an imported LCD screen, which can display the measured value, set value, and time at the same time. Announcements: Do not place the sample in the oven heating state, and place the sample in the state of ensuring that the heating is off;  When placing the sample, there should be a certain space around the upper and lower parts to keep the air flow in the box smooth; There is a cooling plate on the heating wire at the bottom of the chamber, and the sample can not be placed on it, so as not to affect the heat flow and lead to heat accumulation; If the sample will have a phase change at high temperature, it must be packed in a tray to avoid contaminating other samples (for example, it will leak oil or change from solid to liquid after heating); Containing flammable and explosive organic volatile solvents or auxiliaries shall not be put into the chamber.

Application Environmental chamber manufacturers are widely used to test the heat resistance, cold resistance, dry resistance, moisture resistance of various materials, environmental test chambers has a unique design and high-quality materials, whether you are testing aerospace products, electronic instruments, materials, food, medical, electronic and electrical products and various electronic components, environmental test chamber can give you the perfect solution.If you need more models about our test equipment, please reference our https://www.chamber-testing.com/ Applic , ation Environmental chamber manufacturers are widely used to test the heat resistance, cold resistance, dry resistance, moisture resistance of various materials, environmental test chambers has a unique design and high-quality materials, whether you are testing aerospace products, electronic instruments, materials, food, medical, electronic and electrical products and various electronic components,environmental test chamber can give you the perfect solution. Technical Specifications Capacity：245 to 1000L Temperature Range：-70℃ to +180℃ Temperature Fluctuation：≤ ±0.5℃ Temperature Deviation：≤ ±2.0℃ Temperature Uniformity：≤ 2.0℃ Humidity Range (%RH)※2：10%～98% RH Humidity Uniformity：±1.0 % RH Noise test：≤ 68dB

Our Precision Alloy Strip , crafted from carefully formulated alloys such as nickel-based or iron-based materials, offers exceptional mechanical and thermal properties. With high tensile strength, good ductility, and excellent thermal stability, it is engineered to withstand stress and temperature fluctuations. Manufactured to ultra-precise dimensions with a smooth surface finish, this product is highly versatile and can be used in a variety of demanding industries. In aerospace, these alloys are utilized in engine parts, while in electronics, they are commonly found in connectors and other components. In the medical field, these precision alloys are crucial for devices requiring high reliability, and in the automotive industry, they are employed in various high- performance parts. This precision alloy strip ensures consistent performance, making it an ideal solution for applications that require both strength and flexibility across multiple sectors. Key Features of Precision Alloy Strips High Tensile Strength: The alloys are designed to provide superior strength and durability even under stress. Excellent Ductility: Allows for easy shaping and forming without compromising material integrity. Thermal Stability: Withstands significant temperature variations without losing its mechanical properties. Precision Manufacturing: Produced with ultra-precise dimensions to meet industry-specific requirements. Smooth Surface Finish: Ensures reliable performance in sensitive applications, preventing wear and tear. Applications Precision alloy strips like 3J22, 3J40, and 3J53 are used across various high- demand industries due to their excellent magnetic and mechanical properties: Aerospace: These alloys are commonly used in aircraft engine components, where high strength and resistance to thermal expansion are critical. Electronics: Ideal for components such as connectors, transformers, and inductors where precise magnetic properties are required. Medical Devices: Utilized in devices like MRI machines and other magnetic resonance equipment, offering consistent performance under varying conditions. Automotive Industry: Used in manufacturing parts such as sensors, actuators, and connectors that need to perform under extreme stress and temperatures. Permanent Magnet Applications: These alloys are perfect for creating high- performance permanent magnets used in motors and other electrical devices. Packaging & Shipping Packaging: Our precision alloy strips are carefully packaged to ensure safe delivery. The materials are typically packed in moisture-resistant packaging and are placed in sturdy boxes or crates to prevent damage during transit. Shipping: We use reliable global shipping carriers to ensure the timely and secure delivery of all orders. Tracking information is provided for each shipment.

Our 1J33, 1J46, and 1J54 Precision Alloy Soft Magnetic Alloy Sheets are exceptional materials that combine high magnetic permeability and low hysteresis loss for superior efficiency. These alloys are made from high- quality iron-nickel formulations that optimize the transmission and concentration of magnetic fields, making them ideal for applications requiring efficient magnetic performance. The alloys boast excellent dimensional stability, ensuring reliable performance under varying conditions, and good corrosion resistance for enhanced durability. These properties make the alloy sheets perfect for various demanding industries, including electronics, telecommunications, aerospace, and automotive. They are commonly used in the manufacturing of transformers, inductors, magnetic shields, and other magnetic components that require precision and high efficiency. Key Features of 1J33, 1J46, and 1J54 Soft Magnetic Alloys High Magnetic Permeability: These alloys enable efficient transmission and concentration of magnetic fields, optimizing the performance of devices like transformers and inductors. Low Hysteresis Loss: With minimal energy loss during magnetic switching, these alloys contribute to improved efficiency and reduced energy consumption in electronic and electrical applications. Dimensional Stability: The materials maintain their shape and performance even under changing environmental conditions, ensuring long-term reliability. Corrosion Resistance: Offers strong resistance against corrosion, making them ideal for use in harsh environments. Versatility: Suitable for a wide range of industries, including electronics, telecommunications, aerospace, and automotive, thanks to their adaptable properties. Applications These soft magnetic alloy sheets are designed to excel in several industrial applications: Electronics: Used in transformers, inductors, and other components that require high efficiency and minimal energy loss. Telecommunications: Ideal for components like inductors, coils, and magnetic shields used in communication devices. Aerospace: Used in components that need stable magnetic properties under varying temperatures and conditions. Automotive: Commonly found in automotive components like sensors and actuators, where precision magnetic properties are essential. Packaging & Shipping Packaging: Our alloy sheets are carefully packed in moisture-resistant packaging, ensuring safe transit. The plates are often enclosed in protective wrapping and placed in sturdy wooden crates to prevent damage. Shipping: We use trusted global shipping carriers to deliver orders promptly and securely. Tracking information will be provided for each order.

Incoloy 800H Wire is a high-performance alloy known for its exceptional resistance to extreme heat and high-temperature environments. Manufactured with precision and attention to detail, this alloy wire offers remarkable mechanical strength, excellent oxidation and corrosion resistance, and durability under elevated temperatures. It is ideal for applications that require the material to withstand continuous exposure to temperatures up to 1100°C (2012°F), making it suitable for use in industries like chemical processing, power generation, aerospace, and heat exchangers. Incoloy 800H is a nickel-iron-chromium alloy that combines high-temperature strength with excellent resistance to oxidation, carburization, and chemical corrosion. The alloy is especially effective in environments where resistance to high heat and corrosive atmospheres is critical. Key Features & Characteristics: High Temperature Resistance: Incoloy 800H offers superior strength and resistance to oxidation at temperatures up to 1100°C (2012°F), making it ideal for high-temperature applications. Corrosion and Oxidation Resistance: The alloy resists oxidation, carburization, and chemical corrosion, ensuring long-term durability in harsh industrial environments. Excellent Mechanical Properties: The alloy provides outstanding mechanical strength, including good tensile strength, creep resistance, and stress rupture strength. Versatility: Incoloy 800H is highly versatile and can be used in a variety of industrial applications, including heat exchangers, chemical reactors, and components in gas turbines. Weldability: This alloy can be easily welded and fabricated using conventional techniques, offering flexibility in manufacturing complex parts. Long-Term Performance: With exceptional durability under high temperatures, Incoloy 800H ensures reliable performance in critical systems that experience continuous stress and thermal cycling.

The Various Sizes Soft Magnetic Alloy 1J06, 1J12, 1J17 Precision Alloy Pipe is a high-performance material known for its superior magnetic properties. These soft magnetic alloys are designed to offer excellent magnetic permeability, low coercivity, and high magnetic saturation. Available in various sizes to meet specific customer needs, these alloy pipes are ideal for applications in transformers, inductors, magnetic shields, and other critical magnetic components. Whether you are in the electronics industry, automotive manufacturing, or power generation, these soft magnetic alloy pipes help improve device performance and efficiency, delivering reliable magnetic solutions across a range of industries. Designed to withstand harsh environments, they are a perfect choice for applications that require precision, durability, and high performance. Key Features of Soft Magnetic Alloy Pipes High Magnetic Permeability: Ensures efficient magnetic flow, enhancing the performance of inductive components. Low Coercivity: Allows for easy magnetization and demagnetization, making it ideal for dynamic applications. High Magnetic Saturation: Enables better performance in applications with strong magnetic fields. Durability: Designed to withstand high-temperature and harsh environmental conditions without compromising magnetic properties. Versatility: Available in a wide range of sizes to suit various industrial requirements. Application Fields Soft magnetic alloys like 1J06, 1J12, and 1J17 are widely used in applications that require excellent magnetic properties and high reliability. Some of the key industries and applications include: Electronics Industry: Used in the manufacturing of transformers, inductors, and magnetic shielding materials. These components are vital for energy efficiency and signal integrity. Automotive Industry: Employed in components such as electric motors, inductive sensors, and magnetic actuators, which require precise magnetic control and durability. Power Generation: Essential for creating high-performance magnetic components used in electric generators and motors. Telecommunications: Used in communication equipment to improve signal quality and reduce interference. Medical Technology: Employed in the production of MRI machines, magnetic resonance devices, and other medical equipment that rely on soft magnetic materials for precision operation.

Incoloy 800 Bar is a high-performance alloy primarily composed of nickel, iron, and chromium. Known for its exceptional resistance to oxidation and corrosion at elevated temperatures, Incoloy 800 Bar is widely used in industries where materials are exposed to extreme environments. This alloy is especially effective in applications where both heat resistance and corrosion resistance are critical. In this article, we will explore the key features, applications, advantages, and common questions related to Incoloy 800 Bar. Key Features of Incoloy 800 Bar Incoloy 800 Bar is designed to perform in high-temperature, corrosive environments. The alloy’s unique composition gives it outstanding properties, making it a preferred choice for many demanding applications. High-Temperature Resistance: One of the defining characteristics of Incoloy 800 Bar is its ability to maintain structural integrity and strength at elevated temperatures, often exceeding 1,000°C (1,832°F). This makes it ideal for use in environments with extreme heat, such as power plants and industrial furnaces. Corrosion and Oxidation Resistance: The high chromium and nickel content in Incoloy 800 Bar provides excellent resistance to oxidation and corrosion, even in harsh environments. This alloy is highly resistant to sulfidation, carburization, and oxidation, making it suitable for use in high-temperature industrial processes. Superior Mechanical Strength: Incoloy 800 Bar is known for its high tensile strength and yield strength, which ensures that it can withstand mechanical stress and pressure in extreme conditions without compromising its integrity. Thermal Stability: This alloy is not only heat-resistant but also resistant to creep deformation. It retains its mechanical properties under prolonged exposure to high temperatures, ensuring long-term durability. Weldability and Machinability: Incoloy 800 Bar is versatile and can be easily welded and machined, allowing for flexibility in design and fabrication. Applications of Incoloy 800 Bar Incoloy 800 Bar is used in various industries that demand high performance under extreme conditions. Some of the primary applications include: Chemical Processing: Incoloy 800 Bar is commonly used in reactors, heat exchangers, and piping systems in chemical plants. Its resistance to high temperatures and corrosive chemicals makes it ideal for processing environments that involve harsh acids and gases. Power Generation: The alloy is widely used in power plants for critical components such as boiler tubes, nuclear reactors, and steam generators. Incoloy 800 Bar’s ability to resist high heat and oxidation is essential for maintaining system efficiency and safety in power generation facilities. Aerospace: Incoloy 800 Bar is used in aerospace applications, including jet engines and exhaust systems. The alloy’s ability to withstand high temperatures and corrosive gases ensures reliability in the aerospace sector. Marine Industry: The alloy is frequently used in marine environments, where resistance to saltwater and corrosive chemicals is crucial. Incoloy 800 Bar is found in components such as valves, fittings, and structural parts in ships and offshore platforms. Oil and Gas: Incoloy 800 Bar is employed in the oil and gas industry for tubing, casing, and completion equipment. Its resistance to sour gas and harsh well conditions makes it an ideal material for this demanding industry. Advantages of Incoloy 800 Bar Incoloy 800 Bar offers several key advantages that make it a reliable and cost- effective material for industrial applications: Long-Term Durability: Incoloy 800 Bar’s high resistance to oxidation and corrosion means it can last longer in extreme environments, reducing the need for frequent maintenance or replacement. Enhanced Safety: The alloy’s ability to withstand high mechanical stress and thermal cycling reduces the risk of failure in critical applications, contributing to enhanced safety in industrial processes. Cost-Effectiveness: Though Incoloy 800 Bar is initially more expensive than some other materials, its extended service life and reduced need for maintenance make it a cost-effective solution in high-temperature, corrosive environments. Versatility in Applications: The alloy's excellent formability and weldability allow it to be used in a wide range of industries, offering flexibility for custom fabrication and design.

3J01, 3J21 , and 3J53 precision elastic alloy bars are high-performance materials designed for applications that require exceptional elasticity and stability under stress. These alloys are widely used in various industries, including electronics, automotive, and aerospace, due to their superior mechanical properties. With high elasticity, excellent strength, and resistance to deformation, these Precision Alloy s ensure reliable performance in demanding environments. This article explores the key features, applications, and advantages of 3J01, 3J21, and 3J53 elastic alloys, as well as frequently asked questions about these alloys. Key Features of 3J01, 3J21, and 3J53 Precision Elastic Alloys 3J01, 3J21, and 3J53 precision elastic alloy bars offer a range of superior properties that make them suitable for applications requiring high elasticity, strength, and stability. Here are the key features of these alloys: High Elasticity: These alloys exhibit outstanding elasticity, meaning they can return to their original shape after being deformed, which makes them ideal for use in precision instruments and components subject to repeated mechanical stress. Superior Stability: The alloys maintain their mechanical properties even in harsh environments, offering stability under temperature fluctuations and mechanical load. This makes them suitable for high-performance applications that require long-term durability. High Coercivity: The precision elastic alloys possess high coercivity, which means they are resistant to becoming magnetized or demagnetized by external magnetic fields. This is a critical feature in applications where stability of magnetic properties is important. Excellent Mechanical Strength: The alloys exhibit high tensile strength and yield strength, ensuring that they can withstand high stresses without permanent deformation, even in extreme conditions. Corrosion Resistance: 3J01, 3J21, and 3J53 alloys are resistant to corrosion and oxidation, ensuring long-term performance and durability even in aggressive environments. Applications of 3J01, 3J21, and 3J53 Precision Elastic Alloys The unique properties of these precision elastic alloys make them suitable for a wide range of industrial and technological applications: Precision Instruments: Due to their high elasticity and stability, these alloys are commonly used in the manufacture of precision measuring instruments, such as springs, connectors, and other components where accuracy and resilience are essential. Automotive Industry: The alloys are used in automotive components that require high mechanical strength and resistance to wear, such as suspension springs and high-performance sensors. Electronics: 3J01, 3J21, and 3J53 alloys are ideal for electronic components that need to maintain their mechanical and electrical properties under stress, such as connectors, switches, and terminals. Aerospace: In aerospace applications, where materials are exposed to extreme stresses and temperature changes, these alloys are used in high-precision components, including actuators, engine parts, and structural elements. Magnetic Equipment: These alloys are also employed in the manufacture of high- performance magnetic separators and devices that require materials with high coercivity and stability under varying magnetic fields. Advantages of 3J01, 3J21, and 3J53 Precision Elastic Alloys There are numerous advantages to using 3J01, 3J21, and 3J53 precision elastic alloys: High Elasticity and Resilience: The high elasticity ensures that these alloys can be used in applications that require the material to return to its original shape after stress or deformation. This property is crucial in applications like springs and precision gears. Durability and Longevity: These alloys have exceptional strength and resistance to fatigue, allowing components made from these materials to last longer, even in high-stress environments. High Stability Under Extreme Conditions: 3J01, 3J21, and 3J53 alloys retain their properties under temperature fluctuations and mechanical stresses, making them ideal for demanding applications. Corrosion Resistance: The alloys’ resistance to corrosion and oxidation makes them suitable for use in aggressive environments, extending the service life of components and reducing maintenance needs. Versatility: These alloys are suitable for a wide range of applications across various industries, including automotive, aerospace, electronics, and manufacturing, due to their excellent mechanical properties.

Nimonic 80A alloy bars are high-performance materials designed specifically for use in extreme temperature and stress conditions. Known for their outstanding creep resistance, these bars are ideal for applications in aircraft engine rotor blades, where high strength, durability, and stability are essential. This article will explore the key properties, manufacturing process, chemical composition, and advantages of Nimonic 80A alloy bars, particularly in the aerospace industry. Key Features of Nimonic 80A Alloy Bar Nimonic 80A is a nickel-chromium-based alloy that offers a range of superior properties, making it the preferred choice for high-temperature applications in the aerospace industry. High Creep Resistance: One of the most important features of Nimonic 80A alloy is its excellent resistance to creep, which is the slow deformation of the material under constant stress at high temperatures. This makes it highly suitable for use in aircraft engine rotor blades that operate at extremely high temperatures and stresses. Excellent High-Temperature Strength: Nimonic 80A maintains its mechanical properties even at elevated temperatures, often exceeding 700°C (1,292°F). This allows it to perform reliably in hot sections of gas turbines and engines. Corrosion and Oxidation Resistance: The alloy offers exceptional resistance to oxidation and corrosion, even in aggressive environments where exposure to high temperatures and chemical reactions is common. This ensures long service life and reliability. Fatigue Resistance: Nimonic 80A exhibits high fatigue strength, which means it can withstand the repetitive stresses and strains experienced by components like engine rotor blades. Good Weldability: The alloy is relatively easy to weld and fabricate, making it a versatile material for complex aerospace components that require precision and strength. Manufacturing Process of Nimonic 80A Alloy Bar The production of Nimonic 80A alloy bars involves several stages, each designed to ensure the alloy maintains its superior mechanical properties: Melting The process begins with the melting of high-purity raw materials in an electric arc furnace or induction furnace. The molten metal is refined to remove impurities and achieve the desired chemical composition. Casting Once refined, the alloy is cast into ingots. These ingots are then subjected to a homogenization heat treatment to eliminate segregation and ensure uniformity. Forging The ingots are hot-forged at temperatures above 1,000°C to shape the material and refine its grain structure. This step significantly enhances the mechanical properties of Nimonic 80A. Hot Rolling After forging, the alloy undergoes hot rolling to reduce thickness and achieve the desired dimensions of the bars. This process also helps to improve the directional properties of the alloy. Annealing The bars are annealed at temperatures between 900-950°C to relieve internal stresses and enhance ductility, preparing them for further processing. Finishing Finally, the bars are cut to the required lengths and undergo surface treatments like grinding, polishing, or coating to ensure they meet quality standards. Advantages of Nimonic 80A Alloy Bar Nimonic 80A offers numerous advantages, particularly for aerospace applications that require high strength, stability, and resistance to extreme conditions: Exceptional Creep Resistance: The alloy's ability to resist creep under high- temperature stress is crucial for components like engine rotor blades that experience constant stress over extended periods. High-Temperature Strength: Nimonic 80A can maintain its strength and stability even in high-temperature environments, ensuring the reliable operation of components in gas turbines and aircraft engines. Corrosion and Oxidation Resistance: The alloy's resistance to oxidation and corrosion in high-temperature, high-stress environments makes it a durable material for aerospace applications, increasing the lifespan of engine components. Fatigue Resistance: Nimonic 80A has excellent resistance to fatigue, making it suitable for components subjected to repeated stress cycles, such as turbine blades and other rotating parts. Versatility: Nimonic 80A is easy to fabricate and weld, making it adaptable for various aerospace applications, from complex engine parts to structural components.

Our High-Temperature Alloy is designed for high-performance applications. Its tube shape ensures even heat distribution, making it easy to fabricate and ideal for high-temperature environments. Made from a durable mix of nickel, chromium, iron, molybdenum, and niobium, this alloy offers excellent corrosion resistance and strength. Manufactured using a hot-rolling process, the alloy is free from defects and voids, improving overall durability. With a thermal expansion rate of 11.2×10^-6/K, it provides stable performance under extreme conditions, minimizing the risk of cracking or distortion. Ideal for various industries, our High-Temperature Alloy combines strength, stability, and long-lasting reliability for demanding applications. Key Features: High-Temperature Durability: With a thermal expansion rate of 11.2×10^-6/K, this alloy provides excellent stability in extreme conditions. Corrosion and Creep Resistance: The combination of nickel, chromium, and other metals enhances its resistance to corrosion and creep, ensuring a longer lifespan. Versatile Tube Shape: The alloy’s tube shape improves heat distribution and simplifies fabrication, allowing for broad application in various industries. High Strength: Manufactured through hot-rolling techniques, it is engineered for optimal strength and resistance to wear and tear. Applications: Our High-Temperature Alloy is widely used in industries where high heat resistance and durability are required. The primary applications include: High-Temperature Alloy Wire: The alloy’s resistance to oxidation and high- temperature stability make it ideal for use in electrical components, heating elements, and furnace components. 2205 Stainless Plate: DLX High-Temperature Alloy is used in the manufacturing of stainless plates for industries like chemical processing, petrochemical, and food processing. Its excellent corrosion resistance ensures long-term reliability in these harsh environments. Aerospace and Automotive Industries: Due to its excellent strength-to-weight ratio, the alloy is also used in aerospace and automotive applications that require reliable, high-performance materials. Advantages: Corrosion Resistance: The alloy’s composition ensures it is resistant to oxidation, which makes it reliable in environments where other materials might degrade. Stable Performance in High-Temperature Environments: Its low thermal expansion rate minimizes risks of deformation or cracking under temperature fluctuations. Improved Strength Through Hot-Rolling: The hot-rolling process improves the overall material strength, making it ideal for demanding industrial applications. Long Lifespan: Thanks to its creep resistance and high-grade material composition, our High-Temperature Alloy offers durability and long-term reliability. Product Customization: At DLX, we offer customization options for our High-Temperature Alloy to meet the specific needs of our clients. You can request modifications to the alloy wire or steel alloy products to suit your manufacturing processes or operational requirements. Customization Services Available: High-Temperature Alloy Wire Alloy Steel Metal Customization Specific Grade Customization (Ni Cr Fe Mo Nb) Packing and Shipping: We ensure safe and secure packaging for our High-Temperature Alloy products. Each product is carefully packed in a durable cardboard box, lined with foam for additional protection during transit. To prevent any damage, the alloy is wrapped in plastic and labeled with handling instructions. A tracking number will be provided so that customers can monitor the shipment in real-time.

The High Temperature Alloy Tube is a corrosion-resistant material made from a blend of Nickel (Ni), Chromium (Cr), Iron (Fe), Molybdenum (Mo), and Niobium (Nb). This composition ensures excellent resistance to oxidation and high- temperature corrosion, making it ideal for harsh environments. With a tensile strength of 700–800 N/mm² and an elongation of ≥ 30%, this alloy is highly ductile, capable of withstanding stretching and bending without breaking. It also features a thermal expansion rate of 11.2×10^-6/K, allowing it to perform reliably at high temperatures without deforming or cracking. Manufactured using the hot-rolled process, this alloy is ideal for a variety of industrial applications requiring strength, durability, and resistance to extreme conditions. Key Features: Corrosion & Creep Resistance: High resistance to oxidation and wear, ensuring longevity in extreme environments. High Strength: Tensile strength of 700–800 N/mm², ideal for applications requiring durability. Ductility: Elongation of ≥ 30%, providing flexibility and reducing cracking under stress. Stable Thermal Expansion: A thermal expansion rate of 11.2×10^-6/K ensures minimal deformation under temperature fluctuations. Applications: DLX’s High Temperature Alloy Tube is widely used in industries where high- temperature stability and corrosion resistance are essential. Some of its key applications include: Gas Turbines: Perfect for parts exposed to extreme temperatures. Power Boilers: Ideal for components that need to endure high-stress and high- temperature conditions. Chemical Plants: Resistant to the corrosion caused by high-temperature and reactive chemicals. Aerospace & Automotive Industries: Used in components exposed to both high heat and mechanical stress. Industrial Furnaces & Heat Exchangers: Withstands extreme temperatures and provides efficient heat transfer. The alloy's ability to resist oxidation and maintain structural integrity makes it a trusted choice for any application requiring long-lasting performance under heat and pressure. Advantages: Exceptional Durability: The combination of corrosion resistance, high tensile strength, and ductility ensures long-term reliability in harsh environments. Cost-Effective: With its durability and minimal need for maintenance, the High Temperature Alloy Tube provides excellent value over time. Versatile: The alloy can be customized to fit different applications, offering flexibility in various industries, from aerospace to power generation. Customization: DLX offers customized solutions for High Temperature Alloy products to meet the specific requirements of our clients. Customizations include: Product Type: High Temperature Alloy Wire, Alloy Steel Metal. Grade and Material: Ni Cr Fe Mo Nb blend, tailored for specific needs. Delivery Time: Typically 5-7 days, with flexibility for urgent requests. Minimum Order Quantity: 5 units. Support and Services: We are committed to providing comprehensive support for all our High Temperature Alloy products. Our team of engineers is available to assist with: Material Selection & Compatibility Installation and Maintenance Recommendations Custom Design & Modifications Testing & Performance Analysis Our experienced technicians are dedicated to ensuring that the High Temperature Alloy products meet your needs for performance and durability. Packing and Shipping: Product Packaging: Our High Temperature Alloy Tube is securely packed in wooden crates, with metal straps and bubble wrap to protect the product during transit. The packaging is designed to prevent any damage from handling or rough conditions. Shipping: We offer flexible shipping options, including air and sea freight, depending on your location and preference. Once shipped, a tracking number will be provided so you can monitor the delivery. Estimated delivery time will vary based on the shipping method and destination.

The Cheap Price Nvar Kovar 4J29, 4J32 , and 4J36 Precision Alloy Plate is an exceptional product designed for high-performance applications across various industries. Offering cost-effective pricing without compromising quality, these expansion alloy plates are made from advanced precision alloys that ensure reliable performance. These alloys are characterized by their low thermal expansion coefficients, making them ideal for applications requiring dimensional stability in temperature-varying environments. The Nvar Kovar 4J29, 4J32, and 4J36 alloys also offer excellent mechanical strength and durability, which makes them perfect for long-term use. Their corrosion resistance further extends their service life, reducing maintenance costs and increasing overall efficiency. These expansion alloy plates are widely used in electronics, aerospace, and telecommunications industries, where precision and stability are crucial. Whether you are looking to maintain accuracy in temperature-sensitive environments or need materials with high mechanical strength, this precision alloy plate provides the reliability and versatility required. Key Features: Low Thermal Expansion: The low coefficient of thermal expansion ensures the plate maintains dimensional stability, even under temperature fluctuations. High Mechanical Strength: Designed for high-strength applications, these alloys provide durability and long-lasting performance. Corrosion Resistance: Offers enhanced corrosion resistance, ensuring the product maintains its structural integrity in harsh environments. Cost-Effective: Despite its superior properties, the alloy plate is available at an affordable price, making it an excellent choice for both high-end and cost-conscious projects. Advantages: Dimensional Stability: With its low thermal expansion coefficient, this precision alloy plate remains dimensionally stable even when subjected to extreme temperature variations, ensuring accuracy in high-stakes applications. Long-Term Durability: The mechanical strength and corrosion resistance of the alloy ensure a long service life, reducing the frequency of replacements and maintenance. Versatility in Applications: The alloy's adaptability to a range of industries —electronics, aerospace, telecommunications, and more—makes it a versatile material for various uses. Cost-Effective Solution: Despite its high-quality performance, the Cheap Price Nvar Kovar plates offer competitive pricing, making them an ideal choice for companies looking for high performance without a high cost. Reduced Maintenance Costs: The corrosion resistance and durability of the material mean lower long-term maintenance costs, ensuring a better return on investment. Applications: Electronic , s Industry: Used in precision components where stable expansion is critical. Aerospace: Ideal for materials used in aircraft components that must withstand temperature changes without distortion. Telecommunications: Commonly used in connectors and other critical components for reliable performance. Automotive and Industrial Applications: Reliable in systems requiring high thermal stability and strength. Packaging & Shipping: Our Nvar Kovar 4J29, 4J32, and 4J36 Precision Alloy Plates are securely packaged to ensure safe delivery. The plates are wrapped and protected with foam and durable cardboard to prevent any damage during shipping. The products will be sent via air or sea freight based on the customer's preference, and tracking information will be provided to ensure transparency in delivery.

Incoloy 925 bar is a high-performance nickel-based alloy designed for use in a variety of demanding applications. Known for its excellent strength, corrosion resistance, and high-temperature stability, this alloy is commonly used in industries suchs as aerospace, chemical processing, and heat exchangers. One of the standout features of Incoloy 925 is its high Modulus of Elasticity, which is measured at 193 GPa. This property allows it to resist deformation under stress, making it ideal for applications where strength and rigidity are crucial. Additionally, the alloy exhibits a Curie temperature of -115°C, meaning it retains its magnetic properties until exposed to extreme temperatures. This characteristic makes it suitable for scientific and medical applications where non-magnetic properties are needed. The Incoloy 925 is delivered in the Sosoloid state, a heat-treated form that enhances its mechanical properties. This state increases hardness and resistance to deformation. It is highly durable in harsh conditions, making it an ideal choice for high-stress environments. In summary, Incoloy 925 offers excellent strength, corrosion resistance, and high-temperature stability, making it suitable for a wide range of industrial applications such as furnace components, heat exchangers, and chemical processing equipment. Features: Product Name: Incoloy 925 Bar Delivery State: Sosoloid (Heat-treated for enhanced mechanical properties) Testing Facility: Accepts third-party testing such as SGS. Specific Heat Capacity: 470-500 J/kg-K Material Type: Nickel-based alloy Surface Finishes: Bright Color, Acid White, Oxidized Color Our Incoloy 925 is a premium nickel-based alloy with excellent mechanical properties. It is available in various surface finishes, including bright, acid white, and oxidized colors, and is suitable for many industrial uses, offering a reliable solution where strength and stability are crucial. Applications: Incoloy 925 is a versatile material with a wide range of industrial applications. Some common uses include: Furnace Components: Ideal for parts exposed to high temperatures and corrosive environments. Heat Exchangers: Often used in heat transfer systems due to its stability and strength at high temperatures. Chemical Processing Equipment: The alloy’s excellent resistance to oxidation and corrosion makes it suitable for use in chemical reactors and pipelines. Oil & Gas Industry: Widely used in downhole equipment, oil rigs, and other high-temperature, high-stress environments. Aerospace Industry: Perfect for parts requiring high strength, resistance to oxidation, and good performance in extreme environments. Support and Services: Incoloy 925 is designed for demanding industrial environments, and our technical support team is available to assist with all aspects of using this high-performance alloy. We offer the following services: Material Selection Guidance: Helping you choose the right material for your application. Product Customization Options: Tailoring the alloy to meet specific project needs. Installation and Maintenance Assistance: Providing expert advice on proper installation and upkeep. Troubleshooting and Technical Support: Our engineers are available to resolve any issues or challenges you encounter with Incoloy 925. Performance Testing and Analysis: Conducting tests to ensure that the product performs as expected in its application. Our technical experts are highly knowledgeable about Incoloy 925’s properties and capabilities and can offer recommendations to help you achieve optimal results. Packing and Shipping: Product Packaging: The Incoloy 925 bars are securely packaged to prevent any damage during transport. The product is packed in sturdy cardboard boxes or wooden crates, and wrapped in protective materials like bubble wrap to safeguard against scratches and damage. Shipping: Worldwide Shipping: We offer global shipping via reputable courier services to ensure timely and safe delivery. Tracking Number: A tracking number will be provided for all orders, so you can monitor your shipment's progress. Shipping Costs: Shipping costs will depend on the destination and quantity of the product ordered. Delivery Time: Depending on the shipping method, customers will be informed of the estimated delivery time at the time of order.