Machinery, Equipment & Tools

The TL-4 burning furnace consists of 3 layers of cylinders. It uses fully burned natural gas to obtain high-temperature flame, and mixing this temperature with fresh air to achieve the required hot air device. Due to the use of fully automatic single-stage fire, two-stage fire or modulating burner, the output hot air is extremely clean by natural gas fully burned, , meeting the drying and dehydration needs for most stuffs. The external fresh air enter the furnace body under negative pressure, takes two strokes and sequentially cools the middle cylinder and the inner tank. After being fully mixed with the high-temperature flame in the mixing zone, it is extracted from the furnace body and enter the drying room. When the temperature reach the setting number, the main burner stops working and the auxiliary burner continues to burn to maintain the temperature. When the temperature drops to the set lower limit temperature, the main burner will be run again. 4、Advantages/features 1. Simple structure and easy installation 2. Small air volume, high temperature, adjustable from normal temperature to 500℃ 3. Stainless steel high temperature resistant inner tank, durable 4. Automatic gas burner, complete combustion, high efficiency. (After setting up, the system can control the ignition+cease fire+temperature adjust automatic), 5. The fresh air has a long stroke that can fully cool the inner tank, so the outer tank can be touched without insulation. 6. Equipped with high temperature resistant centrifugal fan, large pressure center and long lift

Minimum Order: 1 bags

TL-3 burning furnace is consists of 8 parts: natural gas burner + inner tank + insulation box + fan + fresh air damper + waste heat recovery device + dehumidification fan + control system. It is specially designed for supporting downflow drying room/heating rooms. After fully combusts the natural gas inside the inner tank, it´s mixed with recycle or fresh air, under the action of the fan, it is discharged from the upper outlet into the drying room or heating space. Then cooled air pass through the lower air outlet for secondary heating and continuous circulation. And when the humidity of circulating air reaches the emission standard, the dehumidification fan and fresh air damper will start simultaneously. The exhausted moisture and fresh air implement sufficient heat exchange in the waste heat recovery device, so the moisture is discharged and the fresh air with recovered heat enter the circulation system. 4. Advantages/features 1. Simple structure and easy installation 2. Large air volume and small wind temperature fluctuation 3. Stainless steel high temperature resistant inner tank, durable 4. Automatic gas burner, complete combustion, high efficiency. (After setting up, the system can control the ignition+cease fire+temperature adjust automatic), 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating. 7. Integrating the dehumidification and fresh air system, heat loss is extremely small through by the waste heat recovery device. 8. Automatically replenish fresh air

Minimum Order: 1 bags

TL-2 model Direct burning furnace is consists of 6 parts: natural gas burner + inner tank + insulation box + fan +fresh air damper + control system. It is specially designed to support the left and right circulation drying room. For example, the 100,000 kcal model drying room, it is equipped with 6 fans, three on the left and three on the right. When the three fans on the left rotate clockwise, the three fans on the right rotate counterclockwise in a cyclic alternating manner, forming a relay, The left and right sides serve as air inlets and outlets alternately, taking out all the heat generated by full combustion of natural gas. It is equipped with an electric fresh air damper to supplement fresh air in coordination with the dehumidification system in the drying room/drying place. 4. Advantages/features 1. Simple structure and easy installation 2. Large air volume and small wind temperature fluctuation 3. Stainless steel high temperature resistant inner tank, durable 4. Automatic gas burner, complete combustion, high efficiency. (After setting up, the system can control the ignition+cease fire+temperature adjust automatic), 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating. 7. left and right fans run alternately in cycles to ensure even heating 8. Automatically replenish fresh air

Minimum Order: 1 bags

ZL-3 steam air heater is consists of 9 parts: steel-aluminum radiator fin tube + electric steam valve + drain valve + insulation box + fan + Fresh air damper + waste heat recovery device + dehumidification fan + electric control system. It is specially designed for supporting downflow drying room/heating rooms. After convert the outside steam heat to heat inside the insulation box through by the fin tube, it´s mixing with recycle or fresh air, under the action of the fan, it is discharged from the upper outlet into the drying room or heating space. Then cooled air pass through the lower air outlet for secondary heating and continuous circulation. And when the humidity of circulating air reaches the emission standard, the dehumidification fan and fresh air damper will start simultaneously. The exhausted moisture and fresh air implement sufficient heat exchange in the waste heat recovery device, so the moisture is discharged and the fresh air with recovered heat enter the circulation system.Advantages/features 1. Simple structure and easy installation 2. Large air volume and small wind temperature fluctuation 3. Stainless steel electric heating finned tube, durable 4. Steel-aluminum finned tubes, high heat exchange efficiency. The base tube is made of 8163 seamless tube which is pressure-resistant and durable; 5. Electric steam valve controls the amount of inlet, automatically cuts off or opens according to the set temperature, so that can accurately controls the temperature. 6．High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating. 7. Integrating the dehumidification and fresh air system, heat loss is extremely small through by the waste heat recovery device. 8. Automatically replenish fresh air

Minimum Order: 1 bags

ZL-2 steam air heater is consists of 7 parts: steel-aluminum radiator fin tube + electric steam valve + drain valve + insulation box + fan+ Fresh air damper + electric control system. It is specially designed to support the left and right circulation drying room. For example, the 100,000 kcal model drying room, it is equipped with 6 fans, three on the left and three on the right. When the three fans on the left rotate clockwise, the three fans on the right rotate counterclockwise in a cyclic alternating manner, forming a relay, The left and right sides serve as air inlets and outlets alternately, taking out all the heat generated by steam heater. It is equipped with an electric fresh air damper to supplement fresh air in coordination with the dehumidification system in the drying room/drying place. 1.Simple structure and easy installation 2. Large air volume and small wind temperature fluctuation 3．Steel-aluminum finned tubes, high heat exchange efficiency. The base tube is made of 8163 seamless tube which is pressure-resistant and durable; 4. Electric steam valve controls the amount of inlet, automatically cuts off or opens according to the set temperature, so that can accurately controls the temperature. 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating. 7. left and right fans run alternately in cycles to ensure even heating 8. Automatically replenish fresh air

Minimum Order: 1 bags

ZL-1 steam air heater is consists of 6 parts: steel-aluminum radiator fin tube + electric steam valve + drain valve + insulation box + fan + electric control system. Steam passes the though the fin tube, dissipating heat to the insulation box, mixing and heating the fresh or recycle air to setting temperature, fans bring this hot air into drying room or heating room to be used for dehydration, dehumidification or heating. 4. Advantages/features 1. Simple structure, beautiful appearance, low cost 2. Steel-aluminum finned tubes, high heat exchange efficiency. The base tube is made of 8163 seamless tube which is pressure-resistant and durable; 3. Electric steam valve controls the amount of inlet, automatically cuts off or opens according to the set temperature, so that can accurately controls the temperature. 4. Large air volume and small wind temperature fluctuation 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating.

Minimum Order: 1 bags

DL-3 electric air heater is consists of 7 parts: electric heater + insulation box + fan + fresh air damper + waste heat recovery device + dehumidification fan + control system. It is specially designed for supporting downflow drying room/heating rooms. After convert electrical energy into heart through by the electric heater, it´s mixed with recycle or fresh air, under the action of the fan, it is discharged from the upper outlet into the drying room or heating space. Then cooled air pass through the lower air outlet for secondary heating and continuous circulation. And when the humidity of circulating air reaches the emission standard, the dehumidification fan and fresh air damper will start simultaneously. The exhausted moisture and fresh air implement sufficient heat exchange in the waste heat recovery device, so the moisture is discharged and the fresh air with recovered heat enter the circulation system. 4. Advantages/features 1. Simple structure and easy installation 2. Large air volume and small wind temperature fluctuation 3. Stainless steel electric heating finned tube, durable 4. Automatic control system, group start and close, low load, precise temperature control 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating. 7. Integrating the dehumidification and fresh air system, heat loss is extremely small through by the waste heat recovery device. 8. Automatically replenish fresh air

Minimum Order: 1 bags

DL-2 electric air heater is consists with 6 parts: electric heater + inner tank + insulation box + fan +fresh air damper + control system. It is specially designed to support the left and right circulation drying room. For example, the 100,000 kcal model drying room, it is equipped with 6 fans, three on the left and three on the right. When the three fans on the left rotate clockwise, the three fans on the right rotate counterclockwise in a cyclic alternating manner, forming a relay, The left and right sides serve as air inlets and outlets alternately, taking out all the heat generated by electric heater. It is equipped with an electric fresh air damper to supplement fresh air in coordination with the dehumidification system in the drying room/drying place. 4、Advantages/features 1. Simple structure and easy installation 2. Large air volume and small wind temperature fluctuation 3. Stainless steel electric heating finned tube, durable 4. Automatic control system, group start and close, low load, precise temperature control 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating. 7. left and right fans run alternately in cycles to ensure even heating 8. Automatically replenish fresh air

Minimum Order: 1 bags

My name is susan and I work for XT Intelligent co.,ltd and I would like to take a moment of time to introduce you to our drying system. Our High Efficiency Multi Phase (flowers, leaves such as Rose,pepper etc) dryer combines established drying and processing techniques into a unique attrition flash drying process that keeps your items undamaged. This provides a timely and cost-effective means of stabilizing your valuable harvest before mold, mildew or composting can occur, allowing for future processing at a pace you determine. We design systems to your requirements, let us know your harvested moisture level is (%) as well as your capacity requirements, in “wet/harvested hemp in” lbs/hour and we will provide dryer budget estimates. There is more information, pictures and video at our website. My contact information is below, I would enjoy learning about your farm, call me if you have a few minutes to discuss your drying requirements. All the best, Susan Zheng XT Intelligence Technology Co.,Ltd E-mail : Susan205060@hotmail.com Wechat:+86 13671955713 Skype: Susan205060 Cell Phone: 0086-136 7195 5713 https://www.facebook.com/BELTDRYERMANU , FACTURER (20+) UL/CE parts belt dryer /box dryer Manufacturer - XT Facebook

TL-1 burning furnace is consists of 5 parts: natural gas burner + inner tank + insulation box + fan + control system. The burner forms a high-temperature flame after full combustion in the high-temperature resistant inner tank, these flame mixes with the cold or recirculated air to produce a new and high-temperature air. Under the action of the fan, it is discharged to provide heating for drying machines or places. Advantages/features 1. Simple structure and low cost 2. Large air volume and small wind temperature fluctuation 3. Stainless steel high temperature resistant inner tank, durable 4. Automatic gas burner, complete combustion, high efficiency. (After setting up, the system can control the ignition+cease fire+temperature adjust automatic), 5. High-density fire-resistant rock wool insulation box to avoiding heat loss 6. High temperature and high humidity resistant fan with IP54 protection rating and H-class insulation rating.

Minimum Order: 1 bags

We are the professional OEM manufactuer for the UL/CE belt dryer and box dryer. Attached you can find machine pictures and pls let us know if you have interest to know more details. You can tell us your application / capacity request /voltage /frequency etc. Below pls find some basic information about us: 1 - More than 15 years' experience in dryers production line. 2 - We have solid experience to export to USA / UK / New Zealand market etc. 2 - The advantages for our equipment are : heat recycle using and we provide UL certified parts or CE certified parts for the production line. 4-We use international top brand for key parts such as Siemens screen + OILON Burner etc. Testimonials from our existing UK client : The dryer is efficient in drying the flower biomass delicately enough to keep the valuable terpin profiles that we want for extraction, and dry it enough to be stored without having problems with moisture left in the biomass whilst in storage. Service: we have had good service and can always get hold of someone for assistance if required. As of now, we have not had any problems with the function or operation of the dryer. We successfully harvested and dried over 4 tonnes of flower material last season. Bdgs&Tks, Susan Zheng XT Intelligence Technology Co.,Ltd E-mail : Susan205060@hotmail.com Wechat:+86 13671955713 Skype: Susan205060 Cell Phone: 0086-136 7195 5713 https://www.facebook.com/BELTDRYERMANU , FACTURER (20+) UL/CE parts belt dryer /box dryer Manufacturer - XT Facebook

My name is susan and I work for XT Intelligent co.,ltd and I would like to take a moment of time to introduce you to our drying system. Our High Efficiency Multi Phase (flowers, leaves such as Rose,pepper etc) dryer combines established drying and processing techniques into a unique attrition flash drying process that keeps your items undamaged. This provides a timely and cost-effective means of stabilizing your valuable harvest before mold, mildew or composting can occur, allowing for future processing at a pace you determine. We design systems to your requirements, let us know your harvested moisture level is (%) as well as your capacity requirements, in “wet/harvested hemp in” lbs/hour and we will provide dryer budget estimates. There is more information, pictures and video at our website. My contact information is below, I would enjoy learning about your farm, call me if you have a few minutes to discuss your drying requirements. All the best, Susan Zheng XT Intelligence Technology Co.,Ltd E-mail : Susan205060@hotmail.com Wechat:+86 13671955713 Skype: Susan205060 Cell Phone: 0086-136 7195 5713 https://www.facebook.com/BELTDRYERMANU , FACTURER (20+) UL/CE parts belt dryer /box dryer Manufacturer - XT Facebook

Agricultural Machinery Display SPD-043-Bx Product Description SPD-043-B is an economical display developed by SonnePower, adopting a 4.3-inch LCD screen and designed based on CoDeSys 3.5 programming platform. The product has a number of outstanding features, suitable for a variety of harsh environments in the field of construction machinery, sanitation equipment, mobile equipment, heavy equipment and so on. The SonnePower display has a resolution of 480*272, which can present delicate and clear images. Adopting 24-bit colour screen technology, the colour is vivid and rich, providing users with a better visual experience. The brightness reaches more than 400cd/m2, which can maintain good visibility even under strong light. · High-performance 32-bit MCU providing excellent computing and processing capabilities. · High-definition display: Equipped with a 480*272 resolution screen, featuring a contrast ratio of 450 and a brightness of ≥400cd/m2, delivering clear and bright image display. · 8-channel IO resources with high port multiplexing rate: · 2 CAN interfaces with support for Codesys 3.5 programming, enabling flexible communication and control functions. · Standard RS232 communication port with configurable baud rate: It provides 1 standard RS232 communication port with configurable baud rate, facilitating serial communication with other devices.

CAN Bus Display SPD-043-Ax Product Description The SPD-043-Ax series is a 4.3’ CAN Bus display developed by SonnePower. It is a display screen based on Codesys 3.5 programming. The product features a screen resolution of 480*272, a contrast ratio of 450, and a brightness equal to or greater than 400cd/m2. It has 2 CAN bus interfaces, 1 RS232 serial port for communication, 8 IO resources, and high port multiplexing. In addition, this Mobile machinery display has the advantages of compact size, high integration, and fast response speed. It can operate in harsh environments such as wide temperature ranges, high humidity, strong vibrations, and impacts. It is widely used in various fields, including engineering machinery, sanitation equipment, mobile devices, and heavy-duty equipment. 32-bit high-performance MCU 480 * 272 resolution, 450 contrast, ≥ 400cd/m2 brightness 8 channels IO resources with high port reuse rate 2 channels CAN, supporting Codesys3.5 programming 1 standard RS232 communication port, Baud configurable All input ports support incorrect power and ground connections All output ports are equipped with short circuit and overheat protection Protection level: IP65