Environment & Recycling - Others

Product Description Remove Black Smoke From Tail Gas High Capture Rate DPF Catalyst Product Description 1.Introduction. High capture rate -CDPF We can see DPF particle catcher on diesel vehicles, so as to catch soot particles in exhaust gas and achieve the purpose of purifying exhaust gas. Therefore, in order to improve and prolong the working efficiency and life of DPF, DPF regeneration function is introduced. That is to say, the exhaust temperature is used to burn off the particulate matter collected by the DPF filter and restore the filtering function of DPF. We use a special coating process, through the distribution of coating, to further reduce/reduce the DPF pore size, and increase the carbon particle replenishment efficiency, thus improving the black smoke removal ability. Low regeneration temperature CDPF The product is mainly characterized by passive regeneration at low temperature, and the regeneration temperature is usually lower than 300 degrees. Therefore, it can be completely passively regenerated without additional auxiliary means, and the system is si 2. GRACE DPF general specifications Specification size Volume( L) CPSI Remarks Diameter (mm) Height (mm) 118.4 152.4 1.68 100,200,300 118.4 203.2 2.24 100,200,300 118.4 254 2.80 100,200,300 127 203.2 2.57 100,200,300 143.8 101.6 1.65 100,200,300 143.8 152.4 2.47 100,200,300 143.8 177.8 2.89 100,200,300 143.8 203.2 3.30 100,200,300 143.8 228.6 3.71 100,200,300 143.8 254 4.12 100,200,300 143.8 304.8 4.95 100,200,300 190.5 203.2 5.79 100,200,300 190.5 254 7.24 100,200,300 190.5 304.8 8.68 100,200,300 228.6 203.2 8.34 100,200,300 228.6 254 10.42 100,200,300 228.6 280 11.49 100,200,300 228.6 304.8 12.50 100,200,300 241.3 254 11.61 100,200 241.3 304.8 13.93 100,200 266.7 203.2 11.35 100,200 266.7 254 14.18 100,200 266.7 280 15.63 100,200 266.7 304.8 17.02 100,200 285.75 254 16.28 100,200 285.75 304.8 19.54 100,200 285.75 355.6 22.79 100,200 304.8 254 18.52 100,200 304.8 280 20.42 100,200 304.8 304.8 22.23 100,200 304.8 330.2 24.08 100,200 304.8 381 27.79 100,200 330.2 304.8 26.09 100,200 330.2 381 32.61 100,200 330.2 432 36.97 100,200 Specification size Volume ( L) CPSI Remaiks Length * width Height(ium) 150x150 150 3.38 26, 50,75,86,100,200 Square 150x150 200 4.50 26,50,75,86,100,200 Square 150x150 300 6.75 26,50,75,86,100,200 Square The above is the general specification of DPF. We can also customize the sizes and specifications required by customers.

80 meters anti-freeze insulation Main features 1. Far range, covering a wide range of high efficiency, can achieve precision spray, range 20-200m optional, according to the actual requirements of customers configuration. 2. Can be fixed on the concrete pouring platform, but also supporting diesel generator installed in the transport vehicle. 3. Flexible operation, remote control or manual control, and free to adjust the level of rotation and spray angle, the use of safe and reliable; compared to sprinkler, spray gun, super-saving water. Product Description Working principle of dust removal fog gun machine Through the principle of fan air delivery, the water is pressurized by a high- pressure pump, and the water is atomized by the micronization nozzle of the pipeline. The water mist is sprayed to a long distance through the air volume and pressure of the fan. Due to the small surface tension of the suspended dust particles in the air If it is zero, the water mist can quickly absorb the dust particles in the air, and the dust floating in the air will be adsorbed when it comes into contact, increasing the specific gravity of the dust, inhibiting the flow of dust in the air, and accelerating the dust settling, thereby controlling the amount of dust. 80m Technical parameter table Item Name Parameter Notes Mist canon machine system Equipment Fog cannon body, control system Operation method / Local and remote Remote control distance 100 meters Throw distance(m) 80-85 Static wind speed flat shooting effective distance Air volume(m³/h) 127500 Wind pressure(Pa) 3106 Maximum coverage area(m)² 18000 Water source requirements Water pressure: normal pressure Water quality: PH value 6-8, suspended solids must be ≤50PPm Power requirements Voltage: AC380V, 50Hz Power: 46.4KW Mains or generator connection, voltage can be customized Droplet particles(μm) 20~100um Spray flow(l/min) 160-200 Pitch angle -5°～35° Horizontal rotation angle 320° Applicable ambient temperature 0℃-50 ℃ Antifreeze or noise reduction can be customized Protection level Not less than IP55 Most places of use are open spaces Start method Step-down start Customizable frequency conversion start Rotary drive method Electric/slewing ring Pitch drive mode Hydraulic Dimensions(mm) Base size 1600*1400 Installation requirements Maximum size 2300*2000*1790(H) Transportation and installation requirements Weight 1600KG Technical parameter requirements for spray gun nozzle and pump unit Fan power(kw) 37 Nozzle material Stainless steel 303 material Number of nozzles (a) 80 customized Hydraulic station power(kw) 1.1 Hydraulic station Pump power(kw) 7.5 Pump power 12-120 Stainless steel vertical centrifugal pump Spray ring material Stainless steel 304 material Steel plate thickness of spray tube(mm) 3.5 Equipment bracket Channel steel square tube Equipment paint Paint Inlet size DN40 outer wire remote control 9 keys / 12 keys Drawing Dimensions drawings of various types of fog cannons

Hangzhou TronStol Technology Co., Ltd., was established in 2010 (the company name has been updated in 2019). It is a high-tech enterprise located in Hangzhou. TronStol focuses on pick & place machines and it also helps to provide machine parts like reflow oven, stencil printer, and conveyor to satisfy customer's needs of a completed SMT production line. We are SMT One- Stop manufacturer and provider. It provide pcb assembly machine, automatic pick and place parts, automatic smt pick and place machine, table top smt pick and place machine,etc. The entire SMT production line generally requires conventional SMT pick and place machine parts: nozzles, feeders, etc. For all products in the warranty, our company provides free replacement of accessories. For all out-of-warranty machines, especially when the product has been used for a long time, we recommend that many wearing parts be replaced in time, so as not to affect the patch effect. Our company, as an SMT spare parts supplier, provides all kinds of mounter-related accessories to give customers the greatest support and service. Types of SMT Equipment Accessories Electric Feeder The electric SMT feeder is mainly suitable for the Trosntol A1 pick and place machine. This kind of pick and place feeder only needs electricity to feed, which is more stable than the traditional pneumatic feeder. It makes the placement effect preciser. Vibration Feeder Vibration feeder is mainly suitable for pick and place machines such as Tronstol 3V, Tronstol A1, etc. It is mainly responsible for the feeding of tube components. Label Feeder About of Label FeederTronstol SMT Label Feeder For Tronstol A1 Pick and Place MachineThe easiest and cheapest way of marking a product automatically is the application of a label with a label feeder. ... IC Camera IC Camera is mainly suitable for Trosntol A1 pick and place machine, which is responsible for the scanning and positioning of IC. It is an indispensable part of the SMT machine. Nozzle The pick and place machine nozzle is the key part of SMT to attach and release the absorbed components. It mainly uses the adsorption of vacuum to absorb the components and uses air blowing to put the absorbed components on the coordinate position of the circuit board.

Minimum Order: 1 bags