Consumer Electronics - Others

Can Take Pictures DLNA Mobile Phone Low Call Drop Rate Non-Smart Phone DLNA Mobile Phone Battery Principle: New batteries are partially charged at the factory. Before using your phone, you need to charge the battery according to the instructions below. Some batteries perform best after a few full charge-discharge cycles. 1. Connect the charging cable and the charging base. Insert the charger into the phone's connector port with the arrow pointing up. 2. Plug the other end of the charger into a suitable power outlet (100~240VAC). 3. When your phone indicates that the battery is fully charged, press the release tab and remove the travel charger. DLNA Mobile Phone Parameter: Name Function Earpiece Hear voices here during a talk Left/Right Soft Key Perform the functions identified by the prompts displayed at the left and right bottom of the screen. In idle screen, press the Left Soft key to display the main menu. Press Right Soft key to display PhBook content. “OK” Key Enter the select menu when in menu operation. Power key Power on/off your phone. When powered on and in any other screen, press Power key to the idle screen. Multi-Direct Ional keys From the idle screen, press the up key to display the SMS menu. press down key to display my documents, press Left key to display FM, press Right key to view the Profiles. When in menu operation. scroll through and highlight the menu items USB connecting port lnsert the USB line. # Key ln idle screen, press and hold to switch the vibrate mode. Send Key Send and recelve a call. Press to view the recent calls from idle screen. Numeric Keys lnput numbers and characters. * Key in idle screen, press and hold to lock your phone. DLNA Mobile Phone Precautions: 1. Only use the original battery, otherwise, the phone and/or battery may be damaged; 2. Do not give the mobile phone to children, lest they swallow small parts, which may cause suffocation or suffocation, serious injury, or even death; 3. Do not use strong chemicals (such as alcohol, benzene, thinner, etc.) or detergents to clean the phone. MP3 Playback DLNA Mobile Phone Low Call Drop Rate Strong Signal Mobile Phone 0

NASAN NA-B2+ Air Bubble Remover Built In Air Compressor 7 Inch LCD Glass OCA Glue Laminate Repair, for all touch screen mobile phones iPhone Samsung HTC, Nokia Sony Huawei XiaoMi Defoaming. Features: 1. For LCD, LED, OLED air bubbles removing(Up to 7-inch screen). 2. New appearance design,Touch panel control and timing function; 3. 7inch, small size, ultra-thin in addition to Debubble machine, powerful; 4. High efficient , 30 seconds per piece; 5. High intelligent equipment, one button automatic operation; 6. Operation is extremely simple bubble remove machine; 7. Suitable for all touch screen smart phones in the market: for iPhone, Samsung, HTC, Nokia, Sony, Huawei, XiaoMi. etc.

Minimum Order: 1 bags

TBK-505 Mini Built-in Air compressor Bubble Remove Machine For LCD Glass Refurbish repair,TBK 505 mini Intelligent Defoamer, LCD Screen High Pressure Defoamer, Built-in Air Compressor, OCA Bubble Remove Machine. Features: Ultrasmall size,Built-in Air Pressure,integrated warehouse,wide voltage,Built-in Air pump defoamer. Defoaming machine Integrated air compressor,Detoaming machine integrated ail compressor,It can also work with an external air compressor. Integrated fitting bin,Defoaming machine Built in vacuum,pump,Completely sealed to prevent air leakage. Specially designed for mobile phone LCD repair equipment. Specification: brand model :TBK 505 Voltage:110/220V power :200w Fit bin size:190*110mm Product size :190*295*100mm Package size : 280*360*180mm weight：6kg NOTE: Latc , h upgrade,Selflocking pressure sensing switch. If the door lock is not locked in place the automatic sensing will not work. Operatinginstructions: 1.Press and hold the ENT button,release the ENT when the temperature display is flashing. 2. press+/-toadjust the temperature you need Defoaming temperature(recommended defoamingtemperature45°) adiust the temperature. 3.PRESS ENT again to set For defoaming duration similarly.set thedurationaccordingto+/-setting(3-10minis recommended). 4. then Put theLCDscreen tobe defoaminginto the fitting binclose the bin doorand press ESC to start defoaming.

Minimum Order: 1 bags

SUNSHINE S-918K LCD Vacuum Separator Machine Wide Voltage Mobile Phone/Pad LCD Screen Repair Separator Display Glass Removing 8.5 Inch Broken Screen Separating Tool. Features: 1. 14 -inch large work area, to meet the needs of mobile phones and pad. 2. Built-in two powerful vacuum pump. 3. Double control suction control, partition suction, more accurate. 4. 8.5 Inches Large Working Space Compatible with a variety of mobile phone LCD screen removal. 5. Super Suction air pump, low noise and vibration, more powerful suction. 6. Visual Temperature Control Panel CNC precision temperature adjustment, temperature preset, easy to remove the screen. Specification: Product name: Vacuum Separator Model: S-918K Product size: 283*170*120mm Package size: 312*210*165mm Working size: 110*190mm/8.5 Inches Net weight: about 1.81kg Cross weight: about 2.3kg Power supply: AC 110-220V Power: 100W Applicable: Most Mobile Phone Screens Configuration: Host, Power Cord, Separation Pad, Manual

Minimum Order: 1 bags

MECHANIC iMark X Intelligent Laminator & Bubble Remover 2-in-1 Machine for Mobile Phone Tablet Screen Repairing, for LCD/straight Screen for iPhone, XIAOMI, HUAWEI OPPO, Samsung android Devices Voltage 110V/220V. Specifications ModelNumber : MECHANIC Imark X function : mobile phone LCD screen bonding Suitable for : iPhone /android Features : suitbale for straight screen Workspace : 10 inches Voltage:110V/220V Power: 350W MECHANIC Premiere Laminator & Bubble Remover 2-in-1 Machine iMark X * One-button start * Quick defoaming * Auto laminating * Smart panel * 10-inch workbench Product Highlights 1. iMark X can realize LCD laminating and defoaming at the same time. 2. New built-in preheating platform for laminating area. 3. Strong performance, excellent laminating effect. 4. It can defoam up to 7 screens with a maximum of 10 inches at the same time. Package includes: 1 x Laminator 1 x Power cable

Minimum Order: 1 bags

Back Glass Position Protecting Auto Alignment Mold For Laser Machine 8P X Xs 11 12 Pro Max Remove Rear Cover. This is the Alignment Mold For phone protector mask, which is a TOOL for protecting your IPhone camera ,charging port, battery, flex etc when you change the broken battery door cover by back gass laser separating machine, like TBK 958A 958B 958C 958M or other laser machines. Use for the phone protector mask, including model : For iPhone 8G, 8Plus, X , XS, XR , XS Max , 11 , 11Pro , 11Pro Max , 12 , 12Mini , 12Pro , 12Pro Max.

Minimum Order: 1 bags

WYLIE K85 preheating platform for Phone X - 12 Pro Max face dot matrix for logic board repair, WL 220V 110V pre-heating station thermostat platform heating plate for Phone X to Phone 12 pro max motherboard repair fixture, WL K85 face dot matrix repair tools preheating platform for Phone X/XS/XS MAX/11/11 Pro/11 Pro Max/12/12 Pro/12 Pro max/12 mini motherboard middle layered welding station face dot matrix repair. WL K85 Phone Phone Motherboard Middle Layered Welding Station Face Dot Matrix Repair Tools Preheating Platform For Phone x-12 pro max. Product Features : WYLIE K85 intelligent disassembly welding table Motherboard laminated face dot matrix non - destructive repair Free face repair video with technical support to solve the pain points will not repair face 40 -280 degrees intelligent temperature control LED digital display 110V / 220V universal preheating platform Support X/XS/XS MAX/11/11 Pro/11 Pro Max/12/12 Pro/12 Pro max/12 mini motherboard laminating and fitting 11 Series tail insert wire repair Photosensitive wire repair front photo head repair dot matrix glass repair seal renewal extension module

Minimum Order: 1 bags

WL HT007 Intelligent Mainboard Layered Soldering Station for Phone X-14 Pro Max. WL HT007 Preheating Desoldering Station for Phone X/XS/XS Max/11/11 Pro/11 Pro max/12/12 mini/12 Pro/12 Pro max/13/13 mini/13 Pro/13 Pro Max/14/14Pro/14Pro Max motherboard. Features : Support voltage 110V-220V. Output safe voltage 24V DC high performance intelligent welding station. The dynamic temperature is displayed in real time by a microcomputer and the eddy current heating system makes the power smaller and the heating efficiency higher. The resistance heating + electromagnetic induction heating at the same time makes the eddy current heating more powerful. The optimum precise welding temperature can be calculated in real time by synchronous ambient temperature, which makes the welding work more ideal and convenient.

Minimum Order: 1 bags

Qianli MEGA-IDEA PCB soldering platform for Phone X/XR/XS/XS Max/11/11 Pro/11 Pro Max IC chips BGA separation, Qianli motherboard thermostatic preheater for Phone X-11 Pro Max logic board soldering repair. This welding platform is used for reflow logic boards, PRE-Heating logic boards, also used for logic board separation by layers. Removing the gum from the IC chips, Removing and replacing the IC chips. QianLi Mega-IDEA 3 IN 1 pre-heating station is cleverly designed to support all Phone X-XS Max 11-11 Pro Max logic boards, there are no additional molds to buy or use. Features : Standalone pre heat / soldering / De-Soldering platform Work with logic boards on Phone X, XR, XS, XS Max and 11, 11 Pro, 11 Pro Max Precise targeted temperature Rapid temperature increase Non-slip construction with added weight for stability Digital temperature display Supports 110V – 220V Compatible with : Phone X/XR/XS/XS Max, Phone 11/1 Pro/11 Pro Max

Minimum Order: 1 bags

Qianli MEGA-IDEA Hot Stone preheating platform is used for removing IC glue, such as CPU, Nand flash, ect. Product Features : Material: synthetic stone / silica gel / pure copper Temperature: 220 ℃ - 240 ℃ Voltage: AC100-250V Copper heating core, ensure heating efficiency; synthetic insulation bottom case. Available CPU models: A10, A11, A12, A13 Available Nand flash models: Phone 7,7P,8,8P,X,XS,XS MAX,11,11 Pro, 11 Pro MAX. Available fingerprint cable: Phone 7, 7P, 8, 8P. Other tiny chips.

Minimum Order: 1 bags

Mijing iRepair MS1 Soldering heating Staion MS1-14 module for Phone 14/14 Plus/14 Pro/14 Pro Max. iRepair MS1 desoldering preheating platform For Phone X-14 Pro Max motherboard CPU IC heating disassembly and glue removal. Feature: 1. iRepair MS1 pre-heating staion for Phone X/XS/XS MAX/11/11Pro/11 Pro Max/12/12 mini/12Pro/12 Pro Max/13/13mini/13 Pro/13 Pro Max/14/14 Plus/14 Pro/14 Pro Max motherboard soldering separating. 2. Mijing iRepair MS1 Multi-function Desoldering Station 3. Newly upgraded heating element, fast heating, precise temperature control 4. Added countdown function, layering and fitting are more secure 5. Phone X -14 Pro Max module + universal module + dot matrix module + follow-up unlimited upgrades. 6. Precise positioning, precise temperature, rapid temperature rise, non-slip weight increase, digital display temperature, intelligent 15 minutes sleep, 183° three minutes extreme speed rise, fast stratification, safe disassembly, no damage to the motherboard.

Minimum Order: 1 bags

TBK-928 LCD Frame Bezel Split Separator for Mobile Phone, Samsung, iPhone. Original TBK 928 LCD Touch Screen Frame Dismantle Manual A-frame Separator For Mobile Phone repair. TBK 928 LCD dismantle machine for phone screen replacement repair. Features: 1. Dismantle Machine Frame Separator for Mobile Phone Precisely Adjust By Micrometer. 2. Non-electric operation, convenient and efficient. 3. Double suction cups with double handles, easy to use. 4. Features removable location column and location column locking screw, max width support 9cm. 5. Accurate adjustment of micrometer, high separation accuracy. Parameter: Model: TBK-928. Size:200*215*160mm. Package size: 250*260*185mm. Gross weight: 3.4kg.

Minimum Order: 1 bags

WYLIE WL-1808 LCD Separator For Pad Tablet PRO 11 12.9 15inch screen housing back cover heating separating. WYLIE WL-1808 2 IN 1 LCD heating separating machine for 15-inch screen. WL-1808 2 in 1 15-inch LCD Screen Heating Pad for All Size Suitable LCD Separator Heating Plate Refurbishment Machines. Features: 1. WL-1808: exclusive design 2-in-1 lcd separator machine. 2. for phone and pads, 15 inch working plateform. 3. Can perfectly separate all slzes of lpads on the market.

Minimum Order: 1 bags

Professional Digital Auto Glue Dispenser LY 983A Glue Dropper Solder Paste Liquid Controller Fluid Dispenser Tools Machine. Features: Manual or timer operation modes Foot pedal controlled Suck-back feature ensure no dripping Designed for wide range of application as EFD, I&J Fisnar Complete with an accessory dispensing kit Timer mode dispensing time 0.01-99.99 seconds Timer mode cycle time 0.1-9.9 seconds Manual mode, materials could be dispensed continuously until operator release the foot pedal This unit need to be connected to air compressor (1.5HP or above)

Minimum Order: 1 bags