Brake Systems

Name: 10" x 2-1/4" Trailer Brake Drum Description: This type brake drum is for 3.5K capacity trailer axle and popular in Australia. The PCD pattern are 5 on 4-1/2", 5 on 4-3/4“, 5 on 5", 5 on 5-1/2".

Minimum Order: 300

Name: 10" x 2-1/4" Trailer Brake Drum 6 on 5.5" Studs Description: Our trailer brake drums are a popular choice for the RV, trailer, caravan and boat trailer suppliers. The different PCD measurements trailer brake drums are suitable of many brake assemblies.

Minimum Order: 300

Name: 12" x 2" Trailer Brake Drum Description: We have a large variety of trailer brake drum. This 12" trailer brake drums are available from 5,200 lbs to 7,000 lbs capacities axle. What’s more, we can produce it according to customer's requests, drawings or samples.

Minimum Order: 300

√ Trailer Brakes √ Hydraulic Trailer Brakes √ Trailer Disc Brakes √ 1400 KG (15”/16” WHEEL) √ Hydraulic Disc Brakes √ 1600 KG (13”/14” WHEEL) √ Trailer Disc Brake Caliper √ Hydraulic Disc Caliper √ Hydraulic Brake Caliper The galvanized trailer hydraulic disc brake caliper is made from cast iron, has a phenolic piston and two pieces of non-asbestos semi-metal brake pads. Having excellent anti-rust, anti-corrosion, and anti-wear performance. This trailer hydraulic disc brakes fit the hubs / rotors which have 5 x 4.25” PCD, 5x 4.5” PCD, 5 x 4.75” PCD or 6 x 139.7mm PCD, they suitable for installations where more than one axle is used. This trailer hydraulic brake caliper applies to boat trailers, caravans, car trailers and box trailers. The hydraulic brake caliper is easy to install, it can replace the AL-KO hydraulic calipers. Features l Used with IQ7 or hydraulic over ride couplings (the load weights exceeding 2000 kg). l Requirement of disc hubs and rotors: Thicknesses from 12 mm to 15 mm. l Galvanized coated can prevent the corrosion of seawater. l Mounting bolts, spring washers and pads are included. Quick and easy installation. l This hydraulic disc brake calipers exchange with AL-KO and Trojan MK7 calipers, but have different appearance. Specifications Ø Axle Capability: 1400 kg (15”/16” wheel), 1600 kg (13”/14” wheel) Ø Mounting Bolts: 12mm H.T. x 45mm Ø Bolt Spacings: 88.9mm (3.5”) Ø Recommended operating pressure: 6.9 mpa (1000psi) Product Composition ² Non-asbestos semi-metal brake pads x 2 ² Galvanized Cast Iron Brake Caliper Body x 1 ² Bleed Screw x 1 ² Phenolic Resin Piston x 1 ² Piston Seal x 1 ² Piston Dust Boot x 1 ² Slide Pin Kit x 1 ² Slide Dust Boot x 2

Minimum Order: 400

√ Boat Trailer Hydraulic Disc Brake √ Hydraulic Disc Brake Caliper √ Hydraulic Disc Brakes √ 1400 KG (15”/16” WHEEL) √ Trailer Calipers √ 1600 KG (13”/14” WHEEL) √ Hydraulic Brake Caliper √ Stainless Steel Brake Caliper √ Trailer Brakes Caliper √ Ceramic Brake Pads The trailer brake caliper is stainless steel material, it has a phenolic piston and two pieces of ceramic brake pads. Upgraded trailer calipers have high rust-protection, high corrosion resistance and excellent anti-wear performance. The hydraulic trailer brake calipers suitable for boat trailers, box trailers and car trailers. This caliper will fit AL-KO trailer hydraulic disc brakes that use a 5 or 6 lug trailer disc rotor. Other specifications are same as the cast iron trailer hydraulic disc brake type. Features l Used with IQ7 or hydraulic over ride couplings (the load weights exceeding 2000 kg). l Requirement of disc hubs and rotors: Thicknesses from 12 mm to 15 mm. l Stainless steel caliper body and pads backing plate can prevent the corrosion of seawater. l Mounting bolts, spring washers and pads are included. Quick and easy installation. l This hydraulic disc brake calipers exchange with AL-KO and Trojan calipers, but have different appearance. Specifications Ø Axle Capability: 1400 kg (15”/16” wheel), 1600 kg (13”/14” wheel) Ø Mounting Bolts: 12mm H.T. x 45mm Ø Bolt Spacings: 88.9mm (3.5”) Ø Recommended operating pressure: 6.9 mpa (1000psi) Product Composition ² Non-asbestos semi-metal brake pads x 2 ² Galvanized Cast Iron Brake Caliper Body x 1 ² Bleed Screw x 1 ² Phenolic Resin Piston x 1 ² Piston Seal x 1 ² Piston Dust Boot x 1 ² Slide Pin Kit x 1 ² Slide Dust Boot x 2

Minimum Order: 400

√ Trailer Brake Calipers √ Light Duty √ Mechanical Disc Brake Calipers √ 1000 KG (15”/16” WHEEL) √ Trailer Mechanical Brake Caliper √ 1300 KG (13”/14” WHEEL) √ Mechanical Disc Brakes √ Trailer Disc Brakes √ Boat Trailer Mechanical Disc Brake √ Forward Pull The trailer mechanical disc brake calipers have two configurations, forwarder pull and centre pull. The forward pull is used on beam axle, and the centre pull is used on independent rubber suspension. These trailer mechanical disc brakes are designed to suit the toughest marine environment, regularly for boat trailers. These light duty forward pull trailer brake calipers are easy to cooling and washed after dunked in corrosive salt water. This trailer mechanical brake caliper is hot dip galvanized cast iron caliper body with two pieces non-asbestos semi-metal brake pads, dacromet coated and stainless steel are available. The bushes, springs and bolts etc. are made from stainless steel. Features l Requirement of disc hubs and rotors: Thicknesses from 12 mm to 15 mm. l Galvanized coated and stainless steel accessories can prevent the corrosion of seawater. l Mounting bolts and pads are included. Quick and easy installation. l Mechanical Disc Brakes are more affordable than hydraulic disc brakes. l This mechanical disc brake calipers exchange with AL-KO calipers. Specifications Ø Axle Capability: 1000 kg (15”/16” wheel), 1300 kg (13”/14” wheel) Ø Mounting Bolts: 7/16 UNF Ø Bolt Spacings: 88.9mm (3.5”) Ø Max cable pull input: 200 kg Product Composition ² Non-asbestos semi-metal brake pads x 2 ² Galvanized Cast Iron Brake Caliper Body x 1 ² Inner & Outer Bushes x 2 ² Return Spring x 1 ² Straight Lever x 1

Minimum Order: 400

√ Trailer Disc Brake √ Heavy Duty √ Disc Brake Caliper √ 1700 KG (15”/16” WHEEL) √ Boat Trailer Disc Brakes √ 2000 KG (13”/14” WHEEL) √ Galvanized Mechanical Disc Brake √ Mechanical Disc Caliper √ Trailer Brakes √ Forward Pull The trailer mechanical disc brake calipers have two configurations, forwarder pull and centre pull. The forward pull is commonly used on beam/spring axle, and he centre pull is used on independent/torsion axle. This mechanical forward pull disc brake is old version, it is usually called as boat trailer mechanical brake caliper. It has a hot dip galvanized cast iron caliper body with two pieces non-asbestos semi-metal brake pads and a straight lever. Cast iron and stainless steel are available. All trailer brake calipers provide corrosion resistance and rust protection, which are advantageous to prolong the service of marine trailers. Features l Requirement of disc hubs and rotors: Thicknesses from 12 mm to 15 mm. l Galvanized coated and stainless steel accessories can prevent the corrosion of seawater. l Mounting bolts and pads are included. Quick and easy installation. l Mechanical Disc Brakes are more affordable than hydraulic disc brakes. l This mechanical disc brake calipers exchange with AL-KO calipers. Specifications Ø Axle Capability: 1700 kg (15”/16” wheel), 2000 kg (13”/14” wheel) Ø Mounting Bolts: 12 mm Ø Bolt Spacings: 88.9 mm (3.5”) Ø Max cable pull input (kg) per brake: 300 kg Product Composition ² Non-asbestos semi-metal brake pads x 2 ² Galvanized Cast Iron Brake Caliper Body x 1 ² Slide Pin Kit x 1 ² Slide Dust Boot x 2 ² Straight Lever x 1

Minimum Order: 400

√ Cast Iron Brake Caliper √ Heavy Duty √ Marine Trailer Mechanical Disc Brake √ 1700 KG (15”/16” WHEEL) √ Boat Trailer Brakes √ 2000 KG (13”/14” WHEEL) √ Mechanical Disc Caliper √ Marine Trailer Brake Caliper √ Trailer Brake Pads √ Centre Pull The trailer mechanical disc brake calipers have two configurations, forwarder pull and centre pull. The forward pull is commonly used on beam/spring axle, and he centre pull is used on independent/torsion axle. The difference between these two calipers is the lever. The mechanical centre pull brake is old version, it’s heavy duty trailer caliper. We are Chinese mechanical brake caliper exporter, there are DIY trailer mechanical disc brake kits that can be provided. Every kit contains 2 pcs of trailer brake discs, 2 pcs of brake calipers with pads and bearings etc. This caliper is made of cast iron, stainless steel is available. Other specifications are same as forward pull caliper. Features l Requirement of disc hubs and rotors: Thicknesses from 12 mm to 15 mm. l Galvanized coated and stainless steel accessories can prevent the corrosion of seawater. l Mounting bolts and pads are included. Quick and easy installation. l Mechanical Disc Brakes are more affordable than hydraulic disc brakes. l This mechanical disc brake calipers exchange with AL-KO centre pull calipers. Specifications Ø Axle Capability: 1700 kg (15”/16” wheel), 2000 kg (13”/14” wheel) Ø Mounting Bolts: 12 mm Ø Bolt Spacings: 88.9 mm (3.5”) Ø Max cable pull input (kg) per brake: 300 kg Product Composition ² Non-asbestos semi-metal brake pads x 2 ² Galvanized Cast Iron Brake Caliper Body x 1 ² Slide Pin Kit x 1 ² Slide Dust Boot x 2 ² Centre Pull Lever x 1

Minimum Order: 400

√ off road trailer axle √ Manual Adjustment √ With parking √ trailer brake kit √ 12 inch electric brake √ trailer electric brake system √ 6000 lbs trailer axle √ trailer brake kits ATM (Aggregate Trailer Mass) GTM (Gross Trailer Mass) In Australia, all trailers with ATM or GTM over 2000kg must have a Breakaway Brake setup that will immediately apply the trailer brakes in the event of the trailer becoming disconnected from the towing vehicle. Off-road electric drum brake is both with mechanical parking and with off road design. The plastic core in the magnet will reduce the vibration and the high temperature so that this brake assembly could ensure you a safe drive when you facing the extremely rough road. Meanwhile the trailer axle repair will be easy. Features l Electric off road brakes assembly will work with or without brake actuator. l 12 inch x 2 inch trailer off road electric backing plate is electrophoretic- coated. l Needs only an electric brake controller to work. l Periodic manual adjustment required. l 12 inch trailer brake can work with most trailer axles 6000 lbs including Dexter, Hayes and many others. With the off road design, trailers can go through the rough road freely. Specifications Ø Dimension: 12 inch x 2inch Ø Axle Capability: 6000 lbs Axle Ø Mounting Flange Bolt Pattern: 5 bolts Ø Brake Fit: Left Hand / Driver Side / LH, Right Hand / Passenger Side / RH Product Composition Ø 12” x 2" Brake Shoe Set x 1 Ø E-coat Backing Plate x 1 Ø Off-Road Magnet x 1 Ø Magnet Lever x 1 Ø Handbrake x 1 Ø Springs x 2 Ø Adjuster x 1 Ø Mechanical park brake lever

Minimum Order: 300

√ Mechanical Drum Brake √ 9 X 1.75 inch Drum √ Trailer Mechanical Brakes √ 1200 KG √ Mechanical Brake Set √ 1450 KG √ with Handbrake √ Trailer Mechanical Backing Plate 9" mechanical trailer drum brake kit is suitable for caravans, camper trailers, boat trailers, horse floats and box trailers. The 9” mechanical brake assembly with lever brake has two identical shoes, there is no primary shoe or secondary shoe as in electrical brake assemblies. The recommended maximum load of 9” x 1.75” trailer mechanical brakes for 15”-16” wheel is 1200 kg, and 1450 kg for the axles of 13” and 14” wheel. It is worth noting that the matched drums have 5 or 6 bolt patterns. Most of 9 inch trailer mechanical backing plate wholesaler in Australia and New Zealand market. Features l Mechanical brakes are cheaper than hydraulic brakes. l Requires only a cable and levers. (sold separately) - no brake cylinder or hydraulic lines necessary. l E-coated backing plates resist wear and corrosion. l Fully Assembled; Quick and easy installation. l The 9" mechanical drum brake exchange with most axle brands including AL-KO, Bawa, and many others. Specifications Ø Dimension: 9 inch x 1 3/4 inch Ø Axle Capability: 1200 kg Axle (15”/ 16” Wheel), 1450 kg Axle (13” / 14” Wheel) Ø Mounting Flange Bolt Pattern: 4 Bolt Ø Brake Fit: Left Hand / Driver Side / LH, Right Hand / Passenger Side / RH Product Composition ² 9” x 1 3/4" Brake Shoe Set x 1 ² 9” E-Coated Back Plate x 1 ² Brake Adjuster x 1 ² Brake cable x 1 ² Springs x 2

Minimum Order: 300

√ Hydraulic Drum Brakes √ 10 x 2.25 inch Drum √ Manual Adjustment √ 3500 lbs √ Hydraulic Trailer Brake √ Uni-Servo √ Marine Trailer Brakes √ Trailer Brake Assembly 10 inch hydraulic drum brakes are rated 3.5k lbs per pair. 10” x 2.25” trailer hydraulic backing plate is fully assembled for a quick and easy installation. The hydraulic drum brakes for trailers are ready to bolt to the 4-hole mounting flange. These hydraulic trailer brake kit interchanges with most major brands of axles, without modifying the axle or mounting flange, such as Demco, Atwood, Axletek, Lippert and Dexter. Please note that the hydraulic brake assembly will deliver 20 percent braking when traveling in reverse. Features l Hydraulic drum brake assemblies are designed for use with a surge-type trailer brake actuator (sold separately). l Fully Assembled; Quick and easy installation. l E-coated backing plates resist wear and corrosion. l Periodic manual adjustment required. l These 10" hydraulic uni-servo trailer brakes exchange with most axle brands including Dexter, AL-KO, etrailer, Demco and many others. Specifications Ø Dimension: 10 inch x 2 1/4 inch Ø Axle Capability: 3500 lbs Axle (13", 14”, 15" Wheel) Ø Mounting Flange Bolt Pattern: 4 bolt Ø Brake Fit: Left Hand / Driver Side / LH, Right Hand / Passenger Side / RH Product Composition ² 10” x 2 1/4" Bonded Uni-Servo Brake Shoe Kit x 1 ² E-Coated Back Plate x 1 ² Single-Servo Wheel Cylinder x 1 ² Springs x 2 ² Adjuster X 1

Minimum Order: 300

√ Hydraulic Drum Brakes √ 10 x 2 1/4 inch Drum √ 10" Trailer Brake √ 3500 lbs √ Marine Brake Assembly √ Free Backing √ Trailer Hydraulic Brakes √ Hydraulic Backing Plates This 10“ x 2.25” hydraulic trailer brake assembly is free backing type, fits standard 4 bolt mounting flange. The brakes work with 10 inch trailer brake drums for 3500 lbs (3.5k) trailer axles. 10” hydraulic free backing brakes incorporates a “fall-away” shoe which diminishes shoe drag when backing up. 12” or 10” trailer brake is great for boat trailers, so the hydraulic trailer brakes wholesaler usually stocks lot of them. Features l Hydraulic free-backing brakes use with a surge-type trailer brake actuator. l Free-backing design lets you reverse without trailer brakes being activated. l E-coated backing plates resist wear and corrosion. l Periodic manual adjustment required. l These hydraulic trailer brakes exchange with most axle brands including Dexter, AL-KO, Demco, and many others. Specifications Ø Dimension: 10 inch x 2 1/4 inch Ø Axle Capability: 3500 lbs Axle (13", 14”, 15" Wheel) Ø Mounting Flange Bolt Pattern: 4 bolt Ø Brake Fit: Left Hand / Driver Side / LH, Right Hand / Passenger Side / RH Product Composition ² 10” x 2 1/4" Bonded Free Backing Brake Shoe Kit x 1 ² E-Coated Back Plate x 1 ² Single-Servo Wheel Cylinder x 1 ² Springs x 2 ² Adjuster X 1

Minimum Order: 300

√ Hydraulic Brake Assembly √ 12 x 2 inch Drum √ Trailer Brake Kits √ 5200 lbs, 6000 lbs, 7000 lbs √ 12” Hydraulic Brake √ Uni-Servo √ Trailer Axle Brakes √ Trailer Surge Brakes 12” x 2” hydraulic uni-servo brakes are replacement for one 5.2k – 7k lbs axle with 5 bolt pattern. The brakes are heavy duty application for 7000 lbs trailer axles. Every 12 inch hydraulic trailer brake assemblies have two pieces of non- asbestos semi metal brake shoes, bonded and riveted are available. The matched drums are 6 bolt or 8 bolt 12” brake drums. Technicians always recommend the customers to use hydraulic brake kit for tandem axles & torsion axles of boat trailers. Features l 12" hydraulic uni-servo brakes use with a surge-type trailer brake actuator (sold separately). l Manual adjustment – using fine tooth brake adjustment. l E-coated backing plates provide corrosion protection. l Pre-assembled and easy installation. l This trailer backing plate exchange with most standard hydraulic brakes, such as Dexter, Titan, Demco, Axletek, etc. Specifications Ø Dimension: 12 inch x 2 inch Ø Axle Capability: 5200 lbs Axle / 6000 lbs Axle/ 7000 lbs Axle (14.5”, 15", 16”, 16.5” Wheel) Ø Mounting Flange Bolt Pattern: 5 bolt Ø Brake Fit: Left Hand / Driver Side / LH, Right Hand / Passenger Side / RH Product Composition ² 12” x 2" Bonded Uni-Servo Brake Shoe Kit x 1 ² E-Coated Back Plate x 1 ² Single-Servo Wheel Cylinder x 1 ² Springs x 2

Minimum Order: 300

√ Trailer Brakes √ 12 x 2 inch Drum √ Hydraulic Brake Assemblies √ 5200 lbs, 6000 lbs, 7000 lbs √ 12" Hydraulic Brake √ Free Backing √ Trailer Backing Plates √ Trailer Drum Brake Assemblies 12” x 2” hydraulic free backing brakes have left hand (driver’s side) and right hand (passenger’s side). The 12" drum brake assemblies require manual adjustment and mount to 5-bolt flange. Customers call these hydraulic brake assembly 5200 lb to 7000 lb (5.2k, 6k, 7k), they are same and work with 12 inch trailer brake drums. The free-backing plates will allow your trailer to back up without having the brakes lock up. We are the trailer hydraulic backing plate factory in China, all of our trailer brakes are up to OEM quality. Features l Using with surge trailer brake actuators. l Regular manual adjustment required l The trailer rolls free when backing up, even if the actuator is activated. l E-coated backing plates provide corrosion protection. l Single plunger design. l This brakes exchange with most standard hydraulic brakes, such as Dexter, Titan, Demco, Axletek, etc. Specifications Ø Dimension: 12 inch x 2 inch Ø Axle Capability: 5200 - 6000 - 7000 lbs Axle (14.5”, 15", 16”, 16.5” Wheel) Ø Mounting Flange Bolt Pattern: 5 bolt Ø Brake Fit: Left Hand / Driver Side / LH, Right Hand / Passenger Side / RH Product Composition ² 12” x 2" Bonded Free Backing Brake Shoe Kit x 1 ² E-Coated Back Plate x 1 ² Single-Servo Wheel Cylinder x 1 ² Springs x 2

Minimum Order: 300