Chemicals & Plastics

Full Name: Diammonium Phosphate Properties: White granular crystal, relative density at 1.619g/cm3, melting point at 155℃, easily soluble in water, insoluble in alcohol, PH value of 1% solution is 8.0 Usage: As a fire-prevention agent for fabric, timber and paper. For food grade it is mainly used as a fermentation agent, nourishment, and so on. Used as a high effective non-chloride N, P compound fertilizer in agriculture. It contains totally 74% fertilizer elements, used as a basic raw material for N, P and K compound fertilizer. Packaging: 25kg bags Technical Data Sheet: Parameter Guarantee Tech grade Food grade Main content (as(NH4)2HPO4) % ≥ 98.0 98 P2O5 % ≥ 53.0 53 Nitrogen(as N) % ≥ 21.0 21 PH 7.8-8.2 7.8-8.2 Moisture % ≤ 0.3 0.3 Heavy metal, as Pb % ≤ -- 0.001 Arsenic % ≤ -- 0.0003 Fluoride % ≤ -- 0.001 Water insoluble % ≤ 0.1 0.1

Minimum Order: 25

Full Name: Monoammonium Phosphate Properties: White granular crystal; relative density at 1.803g/cm3, melting point at 190℃, easily soluble in water, slightly soluble in alcohol, insoluble in ketone, PH value of 1% solution is 4.5 Usage: As a fire-prevention agent for fabric, timber and paper, as well as a fire- prevention coating, and dry powder for fire extinguisher. For food grade it is mainly used as a fermentation agent, nourishment, and so on. Used as a high effective non-chloride N, P compound fertilizer in agriculture. Its total nourishment (N+P2O5 ) is at 73%, and may be used as a basic raw material for N, P and K compound fertilizer. Packaging: 25kg bags Technical Data Sheet: Parameter Guarantee Tech grade Food grade Main content (as NH4H2PO4) % ≥ 98.0 99.0 P2O5 % ≥ 61.0 61.0 Nitrogen(as N) % ≥ 12.0 12.0 PH 4.4-4.8 4.4-4.8 Moisture % ≤ 0.2 0.3 Heavy metal, as Pb % ≤ -- 0.001 Arsenic % ≤ -- 0.0003 Fluoride % ≤ -- 0.001 Water insoluble % ≤ 0.1 0.1

Minimum Order: 25

Full Name: Monopotassium Phosphate Properties: White or colorless crystal, easily soluble in water, relative density at 2.338, melting point at 252.6  , and PH value of 1% solution is 4.5 Usage: Used to manufacture metaphosphate in medical or food industry. Used as a high effective K and P compound fertilizer. It contains totally 86% fertilizer elements, used as a basic raw material for N, P and K compound fertilizer Packaging: 25kg bags, 1000kg bags Technical Data Sheet: Parameter Guarantee Tech grade Food grade Main content (as KH2PO4) % ≥ 99.0 99.0 P2O5 % ≥ 51.5 51.5 K2O % ≥ 34.0 34.0 PH 4.4-4.8 4.4-4.8 Moisture % ≤ 0.2 0.2 Heavy metal, as Pb % ≤ -- 0.001 Arsenic % ≤ -- 0.0003 Fluoride % ≤ -- 0.002 Water insoluble % ≤ 0.1 0.1

Minimum Order: 25

Full Name: Sodium Lauryl Ether Sulfate (AES/SLES) Properties: SLES is a kind of anionic surfactant with excellent performance. It has good cleaning, emulsifying, wetting, densifying and foaming performance, with good solvency, wide compatibility, strong resistance to hard water, high biodegradation, and low irritation to skin and eye. Usage: It is widely used in liquid detergent, such as dishware, shampoo, bubble bath and hand cleaner, etc. SLES can also be used in washing powder and detergent for heavy dirty. Using SLES to replace LAS, phosphate can be saved or reduced, and general dosage of active matter is reduced. In textile, printing and dyeing, oil and leather industries, it is the lubricant, dyeing agent, cleaner, foaming agent and degreasing agent. Packaging: 110kg or 170kg drums Technical Data Sheet: Parameter Guarantee SLES-70% SLES-28% Appearance (25℃) White to yellowish paste Colorless to yellowish clear liquid Active Matter, % 70±2 28±1 Sulphate (%) 1.5Max 1.0Max Unsulphated Matter, % 2.0max 1.5max PH value (1% a. m.) 7.0-9.5 7.0-9.5 Color, (Klett) 20max 10max

Minimum Order: 20 square metres

Full Name: Potassium nitrate Properties: Colorless and transparent rhombic or diamond-shaped crystal white powder, soluble in water, liquid Nitrogen and glycerin, insoluble in water-free ethanol and ether. It is a fully soluble fertilizer with the formula KNO3. It is an ionic salt of potassium ions K+ and nitrate ions NO3−. It occurs as a mineral niter and is a natural solid source of nitrogen. Potassium nitrate is one of several nitrogen-containing compounds collectively referred to as saltpeter or saltpeter. Usage: Used in fertilizers, as a source of nitrogen and potassium – two of the macronutrients for plants. Widely applied in economic crops such as various vegetables, flowers and tobacco. Also can be used as base fertilizer, additional fertilizer, foliar fertilizer, soilless culture, etc. Used as the raw material of fireworks, black powder, fuse and firecracker. In pharmaceutical industry, it is used to produce penicillin potassium salts, rifampin and other drugs. Also used to produce cigarette paper, catalyst and dressing agent; in ceramic industry, used to produce ceramic glaze; heat treatment salt bath. Packaging: 25kg bags Technical Data Sheet: Parameter Guarantee Agriculture grade Tech grade Appearance White crystalline powder White crystalline powder Purity(KNO3) % ≥ --- 99.6 K2O % ≥ 46 --- Nitrogen % ≥ 13.5 --- Chlorides % ≤ 0.2 0.02 Moisture % ≤ 0.3 0.1 Water Insoluble ppm≤ 200 100 Sulphate(as SO4ˉ) % ≤ --- 0.005

Minimum Order: 25

RSPro2100 Large SLA 3D Printer RSPro2100 large scale resin printer is our largest format SLA 3D printer. There are three laser scanning, this innovative scanning additive manufacturing system is perfectly suited for the industrial production of large, high quality fin- ished parts as well as mass part production. ONE PRINTER, MULTIPLE INDUSTRIES Aeronautical Model Automotive Casting Decoration Mold Cutural And Creative Prototype Glass Aeronautical Model Automotive Casting Decoration Mold Cutural And Creative Prototype Glass RSPro2100 large sla 3d printer Technical Data Buy Uniontech 3d printer.

Minimum Order: 1 bags

Plastic mesh Bale Wrap is fast becoming an attractive alternative to twine for the wrapping of round hay bales. This soft white netting has the following advantages when compared to twine: Using of netting dramatically improves productivity because it takes less time to wrap a bale. You will be able to reduce time by more than 50 %. Netting helps you to make better and well - shaped bales which are easier to move and store. The bale net wrap is used in wrapping and fixing silage, hay or maize into round bales. Its netting structure could give average pressure to the silage inside to avoid loss than silage twines. They have less stretch capacity but it could shape the bales and then the bales will be wrapped with silage wrap films to make sealed capsule. Round bales with net inside woud be tight with better shape than bales without net. ※ 8.5g/m2, 9.5g/m2, 10g/m2 ※ 1.05m, 1.23m, 1.3m,1.6m and 1.7m width, Regular length is 2000m and 3000m.

Minimum Order: 200

Thickness: 230um or 250um (9mil or 10mil) Diameter: 8ft, 9ft, 10ft, 12ft(2.4m, 2.7m, 3.0m, 3.6m) Length: 45m, 60m, 75m, 90m, 100m, 120m, 150m or customized. UV Durability: more than 15 months Color: white/black Technology:Five-layer Co-extrusion Material: LDPE/LLDPE/MLLDPE

Minimum Order: 40

We have Red Mercury and Silver mercury for sale. Molecular formula: Sb2O7Hg2. Density: 20/20, 22/22, 24/24, 27/27. Purity: 99.99%. Colour: Cherry red. Sample orders available. Order Red Mercury and Silver mercury Chemical production from Multi Brands Reproduction Laboratory Inc. we supply at both whole sale and retail all over the world with rapid and secured delivery. Where to buy red mercury. How much does red mercury cost? Multi Brands Reproduction Laboratory Inc. Paris 2 Place de la Porte Maillot, 75000, Paris, France Tel: +33753660288 WhatsApp Webmail: info@multi-laboratory.com Website: https://multi-laboratory.com/

Minimum Order: 1 bags

LEVER HOIST takes advantage of ratchet mechanism, is a well known labour-saving appliance. TITIANSUHE’s Manual ratcheting chain hoist are designed to provide solutions for short distance overhead lifting in all industries, cable pulling and tensioning in electricity, cargo securing during transportation, equipment positioning during installation or maintenance, and material handling for construction. All our Manual lever ratchet hoist are type tested with destructive test at minimum 400% of rated load and fatigue tested over 1500 life cycles. They are designed and built with highest safety that meet EN13157, ASMEB30.21 and AS1482 specifications. Ranged from a minimum working load 250kg up to maximum 9000kg, this versatile tool will help you to get job done with high efficiency, but small cost. Types of Manual Ratchet Lever Hoists HSH-A616 0.75 Ton Lever Block HSH-A620 1.5 Ton Lever Block HSH-A636 3 Ton Lever Block Mini Lever Block How To Use A Manual Ratchet Lever Hoists Free Chain Operation- Quickly adjust the loose chain and move the unloaded hook the desired position for load attachment. Step 1: Place the change over switch to the “N” position. Step 2: Pull the lifting chain to the desired position to attach the load. Step 3: Move the change over switch to the “up” or “down” position to disengage the free chain operation. Step 4: Pull the lifting chain from both sides to assure it is out of free chain mode. As one of the most professional lever block manufacturers, we provide lever block chain, ratchet lever block, hoist ratchet, lever chain block, steel wire rope, webbing sling, etc. For more information, please feel free to contact us! There are many lifting equipment manufacturers, but we are one of the best choices for you.

Minimum Order: 1 bags

TITANSUHE produces slings and rigging that are to be used with lifting equipment or crane for positioning, lifting, and transferring large loads. These sling lift and rigging can be categorized into three general types according to their construction and materials: chain slings, polyester slings, and wire rope slings. Sling lifting straps are more used for short-length material handling or road rescues. Polyester slings are widely used in applications that need soft touch and protection to the load's surface. Wire rope slings can be engineered with extremely long lengths, suitable for long- distance material and equipment handling such as bridge and building constructions. Lifting Slings Types for Sale Polyester Slings Webbing Slings and round slings are usually used to lift loads that need protection from damage. These polyester webbing slings are specially designed to carry heavy loads and lift them safely. It's very strong yet lightweight, and its flexibility reduces shock when loading. They come out with bright colors and easily to identify their capacity on body. Chain Sling The chain sling is a very sturdy chain hook tool. Rigging lifting straps are available with grade 100 or grade 80 chain that combined with different accessories to form one, two, three or four chain legs. Hooks with different ends and chain lengths are used for various construction or industrial sites. Wire Rope Sling Wire ropes are often made into different forms of slings for the lifting industry due to their high strength, durability and wear resistance. Why Choose Titansuhe be your lifting slings suppliers? Each chain links and chain components are tempered and quenched to get high strength and abrasion resistance for overhead lifting.To make chains fit properly with hooks or hoists also get each link calibrated before delivery. G80 chain can be used in any rigging application that requires a 30-80 grade chain. To identify class 80 slings and lifting chains, all chains are marked with embossed G80 on body. This do good for your checking during usage. The chain components are also completed through a rigorous inspection process and testing procedure to ensure that the end user gets a quality chain sling. Safe Use of Hoists and Slings Determine the load weight and be sure it’s within the rated capacity of the sling. Chose rigging slings that have suitable characteristics for the type of load, hitch and environment. Never use lifting slings exceeding its rated capacity. When using 2 leg or multi-leg slings, the load angle will affect the rated load. See load chart below. Lifting slings with fittings which are used as a choker hitch shall be of sufficient length to assure that the choking action is on the slings and never on a fitting. When using lifting slings in a basket hitch, be attention to balance the load and prevent slipping. Be sure the fittings have proper shape and size of the opening that can seat properly in the hook or other attachments. Keep rigging slings away from the sharp corners, sharp edges that may cut or damage the slings, protrusions or abrasive surfaces. Do not drag slings on the floor or over an abrasive surface. Do not twist or tie slings into knots or join slings by knotting. Do not pull slings from under loads if the load is resting on the sling. Do not drop slings equipped with metal fittings. Do not use slings that have damages or defect unless it is inspected and accepted by qualified person. When use slings in hitched, it should be able to control the load. Always stand clear from between the sling and the load, and from between the sling and the crane hook or hoist hook. Always keep personnel away from the suspended load. Do not allowed personnel ride the sling. Do not shock loading. Do not twist and kink the sling legs. Always center the load in the hook bowl to prevent point loading on the hook. During lifting, with or without the load, personnel shall be alert for possible snagging. When using slings a basket hitch, always contain and support the load from the sides above the gravity center. Always pay attention to the angle of the legs and select slings with enough length to provide adequate rated capacity. Place blocks under load prior to setting down the load, to allow removal of the slings, if applicable. Do not use Nylon or duplex polyester webbing sling at temperatures above of 194 degrees F (90 degrees C). Do not expose the polyester slings under sunlight or ultra-violet light which will degrade the strength of the slings. Always keep slings in a dry, cool and dark place when not in use. In choker hitch, slings shall be long enough so that the choker lifting chokes onto the sling eye or body and never onto any fittings. Do not use slings at angles of less than 30 degrees from horizontal. Inspection Before Buy Lifting Slings A. Initial Inspection Before placing any new or repaired slings in service, always inspect the sling and be sure that the correct sling is being used, and the sling meets the requirements of this specification and has not been damaged in shipment. Failure to read, understand and follow the use and inspection instructions with each sling may result in severe personal injury or death B. Frequent Inspection Before each using, inspect the slings by a qualified person. C. Periodic Inspection Periodically inspect the slings by a designated personnel base on following information. 1. Sling using frequency 2. Sling service condition 3. Sling service life 4. Periodic inspections should be conducted at least monthly Angle and Load Chart of Lifting & Rigging Slings ANGLE is measured between a horizontal line and the sling leg or body. This angle is very important and can have a dramatic effect on the rated capacity of the sling. As illustrated, when this angle decreases, the load on each leg increases. This principle applies whether one sling is used to pull at an angle, in a basket hitch or for multi-legged bridle slings. This data is only for equally loaded sling legs. Sling angles of less than 30 degrees are not recommended. Sling Angle in Degrees Factor 90 1.000 85 0.996 80 0.985 75 0.966 70 0.94 65 0.906 60 0.866 55 0.819 50 0.766 45 0.707 40 0.643 35 0.574 30 0.500 Products Lifting Tools and Equipment  Chain Hoist  Wire Rope Hoist  Trolley & Clamps  Lifting Clamps  Lifting Jack  Lifting & Rigging Slings  Polyester Slings  Chain Sling  Wire Rope Sling  Wire Rope Winches  Material Handling Equipment  Rigging Equipment  Tools & Hardware  Elevator  Removal Lifting & Rigging Slings From Service Removed slings from service if any of the following are visible: Sling tag information is missing or not readable. Acid or alkalis burns. Melting, charring or weld spatter of any part of the sling. Holes, tears, cuts, snags or embedded particles. Broken or worn stitching in load bearing splices. Excessive abrasive wear. Knots in any part of the sling. Distortion, excessive pitting,corrosion or broken fittings. Any conditions which cause doubt as to the strength of the sling. Metal Fittings that are cracked, deformed, including melting or charring. Hooks with throat openings increased by more than 15 percent or twisted out of plane more than 10 degrees. If you need any kinds of lifting products, please contact us, as one of the most professional lifting equipment manufacturers, TITANSUHE is willing to offer you high quality products.

Minimum Order: 1 bags

The high summer is around the corner. Although some inland residents can't go to the beach to enjoy the sun, sand and sea, but we can dress up our homes, in the hot summer experience a little cool. Types of Summer Ornaments Summer Garden Gnomes Decorations Summer Banner Garland Decoration Tropical Palm Leaves, Hibiscus Flowers, Pineapples, Party Balloons Garland Decoration Tropical Palm Leaves, Hibiscus Flowers, Pineapples, Party Balloons Garland Decoration Summer Party Decoration The Meaning of Summer Decoration Walking to the front of the house, pushing the door open, With the Summer decoration,a touch of light green, pleasant freshness, will release all the thoughts that have troubled you all day. The bright tones and natural lighting make everything so warm and bright, and feel youthful. Cheap Summer Decor for Different Scenes Keep it white and bright Paint everything white, from walls to furniture, then use cream white, sandy or white textiles. The idea was to let more light into the room and make it brighter. Use a pattern with flowers Vibrant colors, ubiquitous patterns and flowers make the living room cheerful, bright and playful. garnish with citrus Simple as it looks, decorating with a bowl of citrus fruit can brighten up a room with a summery feel. Bright orange is a young and stylish color. The office can choose white furniture to make a base, reoccupy orange carpet, and the curtain that contains orange flower bud design is decorated, had better still have the orange chair that a full design feels, of whole space foil all the more modern and lively beautiful beautiful. You can also place some summer plants outdoors. The colorful colors of summer flowers and plants can not only adjust people's mood and thoughts, but also vividly bring out the life atmosphere of summer indoors. The bright red pomegranate flowers will create a fiery and joyful atmosphere, and the pure white or slightly pale yellow flowers will create a quiet and peaceful scene. Since then, orange furniture, red, white and yellow flowers can not only give people a warm, exciting, warm but not sweet feeling of happiness. As a professional ornament manufacturer, we can offer kinds of home decoration products for sale, if you are interested, please leave us a message.

Minimum Order: 1000

The steel formwork is sturdy and durable, and can be reused many times during construction. Simple assembly, fast installation, precise curvature, fixed shape and structure, suitable for buildings requiring a large number of isomorphic structures, high-rise buildings, roads, bridges, etc. The steel box girder of the box girder formwork is a kind of beam in bridge engineering. The interior is hollow, and there are flanges on both sides of the upper part, which are similar to boxes. The steel box girder is generally composed of an outer mold and an inner mold, and the structure of the inner and outer molds is different. Bridge box girder is widely used due to its convenient prefabrication, high rigidity and strong bearing capacity. Box Girder Formwork Parameter Product name Box Girder Formwork Material Q235 Q345 etc. Tolerance According to demand Product diameter custom made Product thickness custom made Surface treatment Polishing, passivation, sandblasting, galvanize, spray paint etc. Application Buildings, high-rise buildings, roads, bridges, etc. Custom drawings Please provide detailed drawings of specifications CAD, PDF, DWG, JPEG, STP, IGS, etc. or according to the inquiry data, we will not disclose to third parties without your permission. No drawings please send us pictures or sketches with dimensions (length, height, width), CAD or 3D files will be made for you if you place an order. Features of box girder bridge The assembly is simple, the template is formed, and the operation is simple. High stiffness, making the concrete form perfect. Repeated use many times Wide range of applications, such as buildings, bridges, tunnels, etc. Structural Form of Box Girder Formwork 1. Box girders are in the form of end molds wrapping side molds and bottom molds supporting end molds; 2. The side mold and the end mold are connected to each other, adopting the connection form of standard parts, which is convenient for the adjustment of the end mold, and the end mold and the bottom mold are connected by standard parts, which is convenient for folding the end mold; 3. The connection between the side mold and the bottom mold adopts the type of tie rod (arranged according to 2m/channel and connected with the side mold truss, 17 points on one side), standard parts (connected by a frame every 300mm, about 100 points on one side) fastening form, Tighten and adjust the length and strength of the tie rod; 4. When the box girder steel formwork is prefabricated, it is necessary to set the reverse arch in the bottom form, and the reverse arch is adjusted to the design drawing requirements through the steel backing plate between the bottom form and the embedded parts of the beam pedestal; 5. The end formwork is designed with a Z-high section. When the drainage slope is assembled on site, we will grind it according to the needs of the other party. The lower edge of the end is provided with a 20mmx20mm chamfer, which is welded and polished by steel plates (to ensure the appearance of the template) to ensure the straightness of the chamfer. , and also easy to assemble and disassemble the template. 6. The drip groove on the lower side of the flange end of the box girder steel formwork is pressed into a U shape with steel plates, welded and polished on the panel. Production Requirements of Box Girder Formwork When designing and manufacturing, it must meet sufficient rigidity strength and stability, and can be reused many times without deformation. When the bottom mold is processed and manufactured, the deviation between its center line and the design position shall not be greater than 2 mm, and its overall flatness shall not be greater than 2 mm/m. The bottom mold and the pedestal should be welded firmly. The side molds should be manufactured in sections, the joints should be tight, the welds should be polished flat, and the flatness of the board surface should be less than 2mm/m, and the misalignment should not be greater than 1mm. There should be no problems or defects on the contact surface between the formwork and the concrete, including welding scars, pits, burns, etc. Packaging and Delivery of Box Girder Formwork Delivery Details: Generally 5-30 days, depending on the quantity. Packaging Details: Box, Steel Tray, Steel Rack, Container. As one of the most professional metalworking suppliers, we provide boiler steel structure, steel boiler, sand casting, steel sheet pile, bridge formwork, etc. For more information, please feel free to contact us!

Minimum Order: 1 bags

The slag well is mainly used for the transition connection between the boiler and the slag dryer. When the slag dryer is in normal operation, it is in the shape of a conical funnel. When the slag dryer is in an accident state, the hydraulic shut-off door at the bottom is closed to form a conical container to store a certain amount of slag. Boiler Slag Removal System Parameter Product name Boiler Slag Removal System Material The slag well is equipped with refractory materials and thermal insulation materials, and the steel structure and refractory materials should be able to withstand the direct impact of large pieces of slag. The refractory material contains corundum component. Application It is used in boiler slag discharge system to store ash and slag when the slag machine has an accident or is overhauled. Price term EXW, FOB, CIF, CFR, CNF, etc. Payment L/C,T/T,Western Union,etc. Port Delivery Qingdao, Shanghai, Tianjin, Shenzhen,etc. Heat Resistance Can withstand high temperature of slag above 900℃ Structure of Boiler Slag Removal System The slag well is equipped with manhole doors, peep holes, coke holes, inspection holes, walkways and escalators. The upper part of the slag well is connected with the water sealing plate of the lower header of the boiler, and the lower part is connected with the shut-off door of the slag well, and the supplier ensures that the bottom of the furnace is sealed. The lining of the slag well has impact resistance and has a lifespan of not less than 100,000 hours. Application of Boiler Slag Removal System The main function is to store ash during slag machine accidents or maintenance; when the slag machine is in normal operation, the slag well is the channel for slag dropping. Usage Instruction for Boiler Slag Removal System The slag well has a storage capacity of not less than 4 hours of slag discharge under the MCR condition. The slag well is usually supported by an independent support type. When an independent support type is used, there should be enough space for the lower slag fishing machine to be pulled out horizontally for maintenance. The slag well water seal tank can effectively absorb the vertical and horizontal expansion of the boiler water wall, and the water seal tank is provided with flushing and sewage measures. When the suspended installation is adopted, there is no water sealing groove, but the expansion of the boiler is absorbed by the lower equipment. The water sealing groove of the slag well is arranged around the slag well, and the water level in the tank and the sealing of the slag hopper are maintained by the continuously overflowing sealing water, and a cooling water spray device is arranged in the slag well. As a professional metalworking factory, we provide sand casting, steel sheet pile, brass casting, etc. For more information, please feel free to contact us!

Minimum Order: 1 bags