Industrial Machinery & Equipment - Others

Electric Cleaning Agent is mainly used for eradicating dirt, dust, and contaminations on the power equipment surface especially clean those which surface was heavily polluted. After cleaning it can significantly enhance the adhesion between the RTV coatings and the surface of insulator. The Advantages of Electric Equipment Cleaning Agent 1. Remove the dust, acid, salt and oil completely; 2. Environmentally friendly, no damage to the equipment; 3. Enhance the adhesion of coating; 4. Volatilize quickly, no residue. Electric Cleaning Agent Characteristics Insulator cleaner can quickly remove dust, oil, charcoal and other dirt from insulators and RPV coating insulators without powering down. After cleaning, the insulator can take on a new look and extend the service life of the insulator. In addition, it has no corrosion to the silicone rubber material and has no effect on the hydrophobicity of the insulator, which is the best cleaning and protection product for the insulator. Electrical equipment cleaning agent can quickly remove harmful substances such as dust, oil, moisture and carbon powder. It has a cleaning strength of 35KV, which has special protection for electrical equipment and switching circuits. It can produce antistatic protective film after cleaning. Non-corrosive for insulators and RTV coating insulators, metals, paint finishes, insulating coatings, plastics, silicone rubber, etc. The Use Method of Electric Cleaning Agent Crubbing and brushing method: Use a dry cloth dampened with an insulator electric cleaning agent for scrubbing or brushing. (Note: when it is not charged) Spraying method: Spraying with a agent for cleaning electrical equipment can quickly remove dust, oil, moisture, carbon powder, metal powder, surface static electricity and other harmful substances on the insulator, and then dry naturally after cleaning. Cautions of Electrical Equipment Cleaning Agent At the site of cleaning equipment, pay attention to ventilation and ventilation; Equipment with serious fever, should not be charged clean; It is strictly forbidden to produce sparks in the workplace; Particularly humid environment, need to use power outage; Be careful not to splash into the eyes during use. If accidentally splashed into the eyes, please rinse immediately with water; Please wear chemical gloves when operation; Avoid sun exposure when not in use. Ruisen is a professional silicone coating suppliers, we provide anti algae coating, algae resistant paint, anti algae paint and etc. Want to know more? Please contact us.

Minimum Order: 1 bags

We can offer different size of disc suspension insulator, including glass disc suspension insulator & porcelain disc suspension insulator for transmission line and substation. contact us get more details about disc suspension insulator, such as tds, application method, oem etc. we can supply different type of disc suspension insulator, also customer required. Disc suspension insulators are used for insulation and fixed wires in high- voltage overhead transmission and distribution lines. Generally assembled into insulator strings for use on lines of different voltage levels. However, the best range of use of different types of corrosion-resistant insulators needs to be determined after trial run. Main Application of Disc Insulator High-voltage line disc suspension porcelain insulators, for insulation and fixing in high-voltage overhead lines, are generally connected in series to form insulator strings for use on lines of various voltage levels. Insulators are classified into two types according to their environment and area. Ordinary insulators are suitable for general use. If the number of insulators is increased properly, the flashover performance can be improved. The anti-fouling insulator is divided into bell-type and double-layer umbrella according to its umbrella structure, which is suitable for industrial dust, chemical, saline, coastal and foggy areas. There are two series of new and old insulators. The old series products are divided into one hour electromechanical load; the new series products are divided according to electromechanical damage load. The new series of products have the advantages of advanced structure, good performance and standardization of metal accessories, which will replace the old series. Structure of Disc Suspension Insulator Disc suspension insulators are made of porcelain, iron caps and steel feet glued to no less than No. 525 Portland cement, porcelain sand or quartz sand cement. The contact surface between the iron cap and the steel foot and the adhesive is thinly coated with a buffer layer. The top of the steel foot has a resilient pad. The surface of the porcelain is generally white glazed. Brown glaze or blue ash glaze can also be applied as needed. The surface of the iron cap and steel feet are all hot-dip galvanized. The push-pull type elastic locking pin of the ball type connecting structure has two forms of W type and R type, which is made of copper material, has good elasticity and corrosion resistance, and is convenient for disassembly and assembly. Slotted cylindrical pins and hump-shaped cotter pins. The former is hot-dip galvanized and the latter is made of copper. The above-mentioned elastic locking pin, cylindrical pin and other parts are supplied with the product set. Ruisen is a professional silicone coating suppliers, we provide polymer suspension insulators, glass suspension insulators, suspension type insulator, glass disc insulator, disc type insulator, porcelain suspension insulator, disc and pin insulators and etc. Want to know more? Please contact us.

Minimum Order: 1 bags

The construction waterproof coating is a viscous liquid polymer synthetic material which has a non-fixed shape at normal temperature, and after coating, a material which can form a tough waterproof coating film on the surface of the base layer by evaporation of a solvent or evaporation of water or reaction curing. Common waterproof coatings are polymer waterproof coatings, two-component polyurethane waterproof coating, oxybutyl polyurethane waterproof coating, one- component polyurethane waterproof coating, polymer cement waterproof coating, polymer emulsion waterproof coating, asphalt waterproof coating and modified asphalt waterproof coating, solvent-based asphalt waterproof coating, water- based modified asphalt waterproof coating, silicone rubber waterproof coating. Common Classification of Construction Waterproof Coating 1. Solvent waterproof coating In such a coating material, a polymer material as a main film-forming substance is dissolved in an organic solvent to form a solution. The polymer material is stored in a solution (coating) in a molecular state. 2. Emulsified waterproof coating Such a water-repellent coating material as a main film-forming material is stably suspended (not dissolved) in water as a macroscopic particle (rather than in a molecular state) to form an emulsion coating. 3. Reactive waterproof coating In such coatings, the polymer material as the main film-forming substance exists in the liquid form of the prepolymer. It is mostly composed of two- component or one-component coatings and contains almost no solvent. Fujian RuiSen New Materials Co., Ltd. was established in 2007, located in Fujian Province, China. RuiSen is one of the largest RTV silicone coating suppliers in China, has many years' experience about R&D, manufacture management, and project management. We are the high-tech public company in China that specializes in Research and Development, Design, Manufacture, Sales and Project construction. Our company covers 30,000 square meters with total investment of 30 million RMB. We have Three RTV Silicon coating production lines, Five Silicon Rubber product lines, R & D center, Inspection center, Outdoor test field and Engineering construction simulation teaching field.Thus, our product center holds various kinds of products that can meet different needs, for example, we have anti spatter coating,anti algae coating and others. Above all, in the research and development of waterproof coating, our company will be committed to improving techniques and taking into application in the future. Ruisen is a professional silicone coating supplier, we provide concrete waterproofing coatings, rtv silicone coating and etc. Want to know more? Please contact us.

Minimum Order: 1 bags

We offer different kinds of composite insulator for substation. Contact us get more details about composite insulator, such as TDS, Application Method, OEM etc. We can supply different type of composite silicone insulator, also customer required. Composite insulators are a special type of insulation control that can play an important role in overhead transmission lines. Composite insulators are also known as synthetic insulators, non-porcelain insulators, polymer insulators, rubber insulators, etc. The main structure is generally composed of a shed skirt, a FRP core rod and an end fitting. The shed skirt is generally made of organic synthetic materials, such as ethylene propylene rubber, high temperature vulcanized silicone rubber, etc.; FRP mandrels are generally made of glass fiber as a reinforcing material, and a oxidizing resin as a base material; The end fittings are generally carbon steel or carbon structural steel coated with hot zinc-aluminum. Classification of Silicone Rubber Insulators Composite insulators can be divided into: line composite insulators and power stations, electrical composite insulators. It can also be divided into rod- shaped suspension composite insulators, pin-type composite insulators, cross- arm composite insulators, pillar composite insulators, wind-proof partial composite insulators, and so on. Advantages of Composite Silicone Insulators Light weight, easy to install; High mechanical strength, not easy to break; Excellent seismic performance and good stain resistance; Fast production cycle and high quality stability. End Fitting Structure Composite insulators vary in their structure depending on the characteristics of use. In addition to meeting the tensile strength, meeting the requirements, and reliably connecting with the mandrel, the design of the metal tip also needs to meet the special requirements for application under high voltage. Composite insulators are generally made in the shape of a rod with a small capacitance. Therefore, the voltage distribution on the surface of the insulator is very uneven. Thus, in normal operation, the generated corona will be harmful, so it is necessary to use a pressure equalization measure. In addition, the synthetic insulating material cannot withstand an electric arc of several tens of kiloamperes. In the event of a short circuit fault, it will burn the umbrella near the wire and the tower, so arcing is required. At home and abroad, the method of adding a pressure equalizing ring is generally adopted to uniform the end electric field, weaken the corona, and lead to the fault arc. The voltage equalizing ring of the composite insulator is a component of the composite insulator. Its function is to control the electric field strength inside the insulator, avoid internal partial discharge, reduce the local electric field strength of the external surface, especially the surface of the metal connecting part, and reduce the radio interference. Leading the power frequency arc to avoid burning the surface of the insulator and minimizing the local electric field strength near the end surface to improve its anti-smudge performance. Ruisen is a professional silicone rubber insulator manufacturer and composite insulators manufacturers, we provide composite suspension insulator, composite polymer insulator, composite post insulator, rtv silicone coating and etc. Want to know more? Please contact us.

Minimum Order: 1 bags

The silicone rubber insulation coating is made from special silicone rubber, high-performance material and other polymers by polymer blending technology. Its basic structural unit is silicon - oxygen chain while its side chain is connected by silicone with another organic radical group. Therefore, this structure makes the coating well combine the properties of both organic and inorganic compound. This product can used for the equipment and components which need protection of insulation, thermos conduction, fire retardant, dampness-proof, etc., such as bare wire, busbar, cable, high-power generator, dry-type reactor, dry-type transformer, switch cabinet and so on, it's quite suitable for the electrical equipment which operated in contaminated and humid environments. Product Standard of Busbar Insulation Coating: DL/T 627-2012 Room Temperature Vulcanized Silicone Rubber Anti-Pollution Coating for Insulators IEEE 1523 IEEE Guide for Application, Maintenance, and Evaluation of Room Temperature Vulcanized (RTV) Silicone Rubber Coatings for Outdoor Ceramic Insulators Contact us get more details about RTV-II Silicone Rubber Coating, such as TDS, Application Method, OEM etc. Product Features of Busbar Insulation Coating: 1. Made of special organic silicone rubber and other polymer and high performance. 2. Safe of electric equipment so important for power system. 3. Breakdown of electric equipment will bring huge loss to power system and entire national production. 4. Our silicone rubber insulation coating protects power system from breakdown like bombing. 5. Applied to equipment or elements need insulating handling, heat-conduction, flame resistant and moisture-proof protection like bare wire, naked bus, electric cable, wall crossing pipeline in high-low pressure substation and distribution system, HP motor, dry reactor, dry transformer and switch cabinet. 6. Especially suitable for electric equipment working in dirt and humid environment. 7. Excellent insulating property: Breakdown field strength of coating is over 20kv/mm. 8. Can effectively stop general short trouble caused by small animal in transformer substation and person injury accident because of nude electric. 9. Non-flammable, self-extinguishing, nice flame retardant with FV-0 class. 10. Excellent heat-conducting: Heat conductivity 0.202W/ (m. K) 10 times of air, so it can release equipment's heat in time to prevent excess temperature. 11. High strength, strong adhesion and high corrosion tolerate. 12. Ozone, UV and environment aging-resistant. 13. Not be easy break down by ozone and UV radiation. 14. Service Life is at least 20 years in nature environment. Item Silicone Rubber Insulation Coating Heat Shrink Tube Electrical Insulation Excellent electrical insulation. Breakdown Voltage is more than 25 kV/mm. Common performance. Cover Effect Excellent adhesion. The coating layer is intense, it could strongly stick to the equipment surface and could well resist to the corrosion caused by acid, alkali, salt and air. Common cover effect especially in the connection part. Thermal Conductivity The coating has closely attached to the conductor and has good thermal conductivity could better release the heat of equipment. Its thermal conductivity is 0.2W/ (m. k), which is ten times then air. Relatively poor due to there is air gap between the tube and equipment. Flame Retardant Hard to burn and has good fire retarding ability up to FV-0 Class. Easy to deform, crack and broke. Application Favorable hardness makes its construction time is short. (less than one working day) It can well fit and protect the surface of special shaped equipment or components and special connection position so that to make the conductors as one. Long construction time and need to disassemble the equipment. It’s easy to crack and broken for the coating on the special shaped equipment or components and the connection or twist place. Maintenance Easy to maintain and repair. The coating will not affect the dismounting of screw or bolt. Moreover, if recoating, the new coating can have integrated fuse with the old coating tightly. Although it’s also convenient to maintain and repair, but the connection place is easy to peel and broke. Ageing Resistance Good hydrophobicity and resistance to ageing, dampness, ozone, radiation, UV, etc. make it free of maintenance and can serve for a long time. Its service life could be more than 20 years. Poor ageing resistance, its service time is about 5 years or even less especially in some bad environment the cracking and break phenomenon will happen. Economic Excellent performance at reasonable cost. Lower cost. Ruisen is a professional silicone coating suppliers, we provide anti algae coating, algae resistant paint, anti algae paint and etc. Want to know more? Please contact us.

Minimum Order: 1 bags

we are main Silicone Rubber Coating Manufacturer, Supplier and Exporter of affordable range of Anti-Blasting & Anti-Spatter Coatings world-over. Our range comprising of Anti-Blasting (FB-PRTV), Anti-Spatter Coating (FB-PRTV) etc. is reckoned for its peerless anti explosion splash effect, necessary for protection of electrical equipment. The Renovation Technology for the Deteriorated Silicone Rubber Composite Bushing (such as CT, composite insulator) to remold its surface, strengthen its structure and recover its surface anti-pollution flashover property. Busing and insulator is exposed to the harsh climate and strong electric field conditions all year long, day and night, the jointed reactions of partial discharge, temperature change, UV radiation, acid rain hydrolysis, etc. will inevitably accelerate its surface deterioration process. The silicone rubber bushing after deteriorated will appear to be weakening or complete loss of hydrophobicity, embrittled, hardening, pulverized, cracking, etc. Due to the deterioration is taken place from outside to inside, so when the surface aging phenomenon happens, necessary measure should be promptly adopted to recover its surface performance and structural strength so that to extend the equipment’s service time and make sure them work in safe status. The renovation for the deteriorated silicone rubber composite bushing： 1. Cleaning: Clean up the unconsolidated and pulverized and other dirt; 2. Repairing: Use preformed silicone rubber patch to repair the worn bushing; 3. Recovering: Use exclusive silicone rubber mending putty to fill the crack surface; 4. Crosslinking: Treat the surface by special-used cleaner which contains low molecule so that the deteriorated Si-O bond will re-crosslink with new polydimethylsiloxane to restore its original property; 5. Coating: The mechanical intensity of deteriorated bushing has weakened to some extent although it has been re-crosslink treated, therefore the liquid silicone rubber coating FB-PRTV is an ideal choice to strengthen the mechanical intensity because of its good tearing resistance. FB-PRTV is a new type of anti-pollution flashover coating of polymer interpenetrating net structure. It's compounded of organosilicon prepolymer, modified silicone rubber and special aramid fibers, it has good mechanical property, high intensity, excellent anti-pollution flashover and anti-explosion scattering protection performance. This product has passed the electrical performance test and 5000 hours accelerated aging test by Wuhan High-voltage Research Institute; It's also successfully experimented in military explosion. Product Standard of Anti-blasting & Anti-spatter Coating FB-PRTV: DL/T 627-2012 Room Temperature Vulcanized Silicone Rubber Anti-Pollution Coating for Insulators IEEE 1523 IEEE Guide for Application, Maintenance, and Evaluation of Room Temperature Vulcanized (RTV) Silicone Rubber Coatings for Outdoor Ceramic Insulators Contact us get more details about FB-PRTV Silicone Rubber Coating, such as TDS, Application Method, OEM etc. We can supply different color of FB-PRTV Coating, such as RED, GRAY, WHITE and other color, also customer required. Ruisen is a professional silicone coating supplier, we provide weld spatter resistant coating, blast proof paint, rtv silicone coating and etc. Want to know more? Please contact us.

Minimum Order: 1 bags

Leveraging upon our experience, we have become a prominent Anti-Algae & Anti- Fouling Coatings (RTV-ZB) Manufacturer, Exporter and Supplier in China and rest of the world. Applicable for flash-over & algae prevention, our well-formulated anti algae coating and anti fouling coating are acknowledged for offering lasting sterilization and inhibition for mold, bacteria, yeast and other microorganisms. Avail them from us in desired quantity and packaging at guaranteed reasonable prices. The Advantages of Anti-algae & Anti-fouling (RTV-ZB): 1. Ready-to-use without adding solvent to make thinning or excassive mixing/shanking before use. Easy to use in different conditions. 2. Excellent Anti-algae and anti-fouling, long-term resistance to weathering and a wide variety of pollution environments. 3. Long-term hydrophobicity, Suppression of leakage current, discharges and pollution flashover. 4. Reduced maintenance and revenue losses, easy to maintain as in washing, compared to conventional insulator surfaces. 5. Strong adhesion to the insulator surface, withstand high pressure. 6. The service life is longer than normal RTV coating, at least 15 years in most service conditions. Stable operation, long-lasting performance. 7. Nontoxic and environmental friendly material. Application Scope of Anti-algae & Anti-fouling Coating (RTV-ZB): 1. RTV-II is ideal Suited for used in a wide variety of pollution environments including, but not limited to, salt spray, salt fog, industrial (cement dust, fly ash, carbon black, acid emissions, etc.) and desert sand. 2. AC and DC systems, all voltage levels. 3. Our RTV-ZB Silicone Rubber Coating can effectively protect ceramic insulator, glass insulator, long rod insulator, circuit transformer, voltage transformer, bushing, circuit breaker, Hollow porcelain insulator, porcelain surge arrest, switchgear cabinet, Transformer insulator and other outdoor electrical equipment. Product Standard of Anti-Algae & Anti-Fouling Coating (RTV-ZB): DL/T 627-2012 Room Temperature Vulcanized Silicone Rubber Anti-Pollution Coating for Insulators IEEE 1523 IEEE Guide for Application, Maintenance, and Evaluation of Room Temperature Vulcanized (RTV) Silicone Rubber Coatings for Outdoor Ceramic Insulators Contact us get more details about RTV-ZB Silicone Rubber Coating, such as TDS, Application Method, OEM etc. We can supply different color of RTV-ZB Coating, such as RED, GRAY, WHITE and other color, also customer required. Ruisen is a professional silicone coating suppliers, we provide anti algae coating, algae resistant paint, anti algae paint and etc. Want to know more? Please contact us.

Minimum Order: 1 bags

KWP non clogging sewage pump WATER PUMP & SEWAGE PUMP dirty water pump sewage pump manufacturer Performance D: 40 - 500mm Q: 6 -3000m3/h H: 3 - 80m Application and Feature KWP type non clogging centrifugal pump is an efficient and energy-saving product. It is highly Efficient Non clogging, It can transport clean water, domestic sewage, chemical wastewater, waste water and sewage sludge. It is divided into vertical and horizontal dual-purpose pumps and K/O/F/N/SA pumps, and the complete specifications also provide a wide range of flow and lift. Centrifugal sludge pump is one of our main product, which can transport clean water, domestic sewage, chemical waste water, waste water and sewage sludge. Sewage pump is highly efficient and non clogging. If you want to know the latest news about Slurry Pumps, Sewage Pump, Chemical Pump And Parts, please come to our website and get a quote for free. https://www.katimachinery.com/

Minimum Order: 1 bags

Multi-stage Submersible Water Pump submersible slurry pump manufacturers submersible pump manufacturers Double suction pump 61,67,68 D:125-350mm Q：10-1800m3/h H： , 12-1145m Single suction submersible pump 65,66 D:65-200mm Q：10-440m3/h H：12-35 , 5m Application and Feature KATI submersible pump is multi-stage vertical and horizontal dual-use centrifugal pump which is manufactured on the basis of the technology introduced from Ritz Company of  German and it is characterized by the advanced construction, the high-efficiency units, the excellent-quality materials, the vertical and horizontal dual-use, the long life, the reliable operation, the low noise and other advantages. The pumps are the upgrading products of the original QJ series products which implemented the standards of Ministry of Agriculture. The series of pump is mainly used for the permanent drainage of coal mines, the surface drainages and the high-pressure jet grouting engineering and it is also applied to water elevating from the deep wells in the mining industry and the urban and rural areas. Series of Ritz multi-stage submersible pump are mainly composed of the motor and the pump, meeting the vertical and horizontal use. The diameter of the supporting motor shaft is thick and the shaft length is short. Multi-stage Submersible Water Pump is characterized by the advanced construction, the vertical and horizontal dual-use, the long life, the reliable operation, the low noise and other advantages. If you want to know the latest news about Slurry Pumps, Sewage Pump, Chemical Pump And Parts, please click here and get a quote for free. https://www.katimachinery.com/product , /Multi-stage-Submersible-Water-Pump.html

Minimum Order: 1 bags

KTN mud pump SLURRY PUMP dredging pump supplier pump manufacturers Performance D:250-1000mm Q:1300-25000m3/h H：40-70m dredging pump Application and Feature High efficiency, wear resistant, stable performance; single casing and double casing structure for choice，single-stage single-suction cantilever horizontal structure, comes with brackets, forced oil lubrication. If you are finding mining pump exporter in China, we will be your best choose! Our Mine Pump has many advantages such as high efficiency, wear resistant, stable performance. https://www.katimachinery.com/ ,

Minimum Order: 1 bags

KTF Froth pump High chromium slurry pump industrial pumps slurry pump manufacturers Performance D: 50 -450 mm Q: 10-5000 m³/h H: 10-65m KATI-Froth pump Application and Feature KTF Slurry Pump series are particularly designed to handle froth and high viscosity slurry in non-ferrous metal extraction where flotation process is utilized, the slurry which contains fine particles and fine dispersion of air bubbles need to be pumped from one flotation cell to another or to the next process, in these conditions the froth pumps are needed. Wear-resistance high chrome white irons or various elastomer molded wet parts are optional for different slurries. Froth Pump are particularly designed to handle froth and high viscosity slurry in non-ferrous metal extraction where flotation process is utilized. Welcome to choose us! Our website: www.katimachinery.com

Minimum Order: 1 bags

KTHH high head slurry pump high pressure slurry pump supplier mining pump exporter Performance D: 20-150mm Q: 10-1000m3/h H: 15 -100m KATI SLURRY PUMP Application and Feature The product is a cantilever and centrifugal pump. The double pump casing structure is used in horizontal and vertical axis, and the inner lining is hard alloy with good wear resistance, corrosion resistance and high reliability. The product is reasonable in structure, reliable in operation and long in-service life. It is especially suitable for middle and high concentration, strong abrasion and high lift. Our High Head Slurry Pump has many advantages such as reasonable in structure, reliable in operation and long in-service life, which s especially suitable for middle and high concentration, strong abrasion and high lift. If you want to know the latest news about the China pump manufacturers, please come to our website and get a quote for free. https://www.katimachinery.com/

Minimum Order: 1 bags

Ceramic pump parts centrifugal pump parts PUMP PARTS &OEM PARTS centrifugal slurry pump parts slurry pump spares Product description：We have ceramic pump parts of different materials to meet any of your needs. At the same time we can customize according to your needs! KATI Machinery is a professional supplier of slurry pumps, submersible slurry pumps, vertical slurry pumps water pumps, submersible water pumps, sewage pumps, mud pumps, ceramic lined pumps, chemical pumps, made to order pump parts & our own OEM pump parts. We can supply high quality centrifugal slurry pump parts, such as pump impeller. We has an extensive sales team, advanced production and supply system, providing various OEM Pump parts. Customized production, one-stop service! If you want to know the latest news about the China pump manufacturers, please come to our website and get a quote for free. https://www.katimachinery.com/

Minimum Order: 1 bags

Rubber slurry pump parts rubber pump parts slurry pump spare parts OEM Pump parts wholesale Product description：Buy low price, high quality Rubber Slurry Pump Parts, you can choose our products. KATI is the leading factory & Company. Warmly welcome new and old customers to visit and patronize! Hebei KATI Pump Group, established in 2000, has 150 staff, including 15 technical specialists and engineers. KATI has a complete turn key production and assembly capability, with more than 50 sets of electric induction furnaces, intermediate frequency furnaces and 30 sets of CNC and machining equipment. Full production capability for castings, machining, heat treatment, final assemblies, sub-assemblies, and in-house test evaluation for QA/QC control. We have independent design product specialists and advanced technology to improve pump service life and efficiency. The company has an extensive sales team, advanced production and supply system, providing various components for aftermarket slurry pumps and water pumps for the metallurgical, mining, power, coal and other industrial sectors of the market. We offer a one stop shop with our in-house foundry, casting high chrome and white iron, machining department, heat treatment department, welding section, assembly department, hydraulic pump testing station and lab facilities with R&D. Current output: 150tons/month of various products and 200 pump assemblies/month. Our website: www.katimachinery.com

Minimum Order: 1 bags