Other Motors

NEMA 24D STEPPER MOTOR NEMA 24 stepper motor is a standard hybrid stepper motor, the step angle is 1.8°, and it is a 2-phase one. As a stepper motor factory, we can offer kinds of stepper motor and driver for sale, anything you need, please leave us a message. If you want to know more about nema 24 stepper motor dimensions, please visit our website.

NEMA 23 ROUND STEPPER MOTOR QUALITY Unlike the nema 23 size motor, the NEMA23 round stepper motor driver is round one, and the size is 56.4*56.4. NEMA 23 ROUND STEPPER MOTOR CHARACTERISTIC PARAMETER STEP ANGLE 1.8°±5% NO. OF PHASES 2 RATED VOLTAGE 2.24 V RATED CURRENT 1.6A RESISTANCE 1.4 ohm±10%   AT 25° INDUCTANCE 1.35mH±20%    AT 1kHz, 1Vrms HOLDING TORQUE 0.26 N.m(3.5 oz.in)TYP. RUNNING TORQUE(AT --PPS) --V.DC, --A/PHASE DIELECTRIC STRENGTH 500V A.C/MIN. INSULATION RESISTANCE 100MΩ+/MIN. INSULATION CLASS CLASS B TEMPERATURE RISE 80K MAX. ROTOR INERTIA 70 g.cm²(0.39 oz.in²) WEIGHT APPROX. 340g(11.9oz) ALLOWABLE THRUST LOAD 15N ALLOWABLE RADIAL LOAD 75N(ON THE SHAFT END) OPERATION AMBIENT TEMP. ‘-20℃---+50℃ OPERATION AMBIENT HUM. 15%----90% LIFE 5000HOURS NEMA 23 ROUND STEPPER MOTOR TORQUE CURVE SPEED VS TORQUE CURVE MODEL: HEM-23S1601 VOLTAGE 24V.D.C ○ SUPPLY WINDING CURRENT 1.6A/PHASE ○ PEAK AVE EXCITATION Full step DRIVE CIRCUIT HDSD2A8 UNIPOLAR # BIPOLAR INERTIA LOAD 10g-cm2 LOT NO.: 060919 If you want to know more about nema 23 motor dimensions, please visit our website.

NEMA 23 Linear Actuator ACME lead screw with high precision, and the lead screw resolution is ±0.017mm. High-density plastic nuts and their life can be over 2 million times. Support to integrated with RS232/RS485, CAN communication protocol. NEMA 23 LEAD SCREW MOTOR CHARACTERISTIC PARAMETER LC23D-75A20 BODY LENGTH 42.3mm RATED VOLTAGE (Vm) DC 2.6 AMPS/PHASE 2 RESISTANCE/PHASE Rm (OHMS) 1.3 INDUCTANCE/PHASE (MH @ 1000Hz) 3.2 HOLDING TORQUE (N-cm) MIN 75 STEP ANGLE (DEGREES) 1.8 STEP ACCURACY (NON-ACCUM)% ±5 LC23D-105A30 BODY LENGTH 53.3mm RATED VOLTAGE (Vm) DC 2.25 AMPS/PHASE 3 RESISTANCE/PHASE Rm (OHMS) 0.75 INDUCTANCE/PHASE (MH @ 1000Hz) 2.5 HOLDING TORQUE (N-cm) MIN 105 STEP ANGLE (DEGREES) 1.8 STEP ACCURACY (NON-ACCUM)% ±5 NEMA 23 LEAD SCREW MOTOR TORQUE CURVE If you want to know more stepper motor faq, please visit our website. Now the price of coreless brushless motor is affordable, if you are interested, please contact us.

NEMA 23 Motor Controller size 23 stepper motors is a standard hybrid stepper motor, the step angle is 1.8°. NEMA 23 CURRENT SQUARE STEPPER MOTOR CHARACTERISTIC PARAMETER STEP ANGLE 1.8°±5% NO. OF PHASES 2 RATED VOLTAGE 3.9 V RATED CURRENT 3.0 A RESISTANCE 1.3 ohm±10%   AT 25° INDUCTANCE 4.5 mH±20%    AT 1kHz, 1Vrms HOLDING TORQUE 1.3 N.m(183.3 oz.in)TYP. RUNNING TORQUE(AT --PPS) --V.DC, --A/PHASE DIELECTRIC STRENGTH 500V A.C/MIN. INSULATION RESISTANCE 100MΩ+/MIN. INSULATION CLASS CLASS B TEMPERATURE RISE 80K MAX. ROTOR INERTIA 280 g.cm²(1.53 oz.in²) WEIGHT APPROX. 700g(24.5 oz) ALLOWABLE THRUST LOAD 15N ALLOWABLE RADIAL LOAD 75N(ON THE SHAFT END) OPERATION AMBIENT TEMP. ‘-20℃---+50℃ OPERATION AMBIENT HUM. 15%----90% LIFE 5000HOURS NEMA 23D SQUARE STEPPER MOTOR TORQUE CURVE SPEED VS TORQUE CURVE MODEL: HEM-23D4401-45 LOT NO.: 2021-10-23 VOLTAGE 24V.D.C ○ SUPPLY WINDING CURRENT 0.3A/PHASE ○ PEAK AVE EXCITATION Full step DRIVE CIRCUIT DM542 UNIPOLAR # BIPOLAR INERTIA LOAD 3g-cm2 If you want to know more about nema 23 high speed, please visit our website. Now the price of stepper motor material is affordable, if you have needs to buy stepper motor, please leave us a message.

NEMA 23C SQUARE STEPPER MOTOR nema 23 stepper is a standard hybrid stepper motor, with the size 56.4*56.4, a step angle is 0.9°. NEMA STEPPER MOTOR CHARACTERISTIC PARAMETER STEP ANGLE 0.9°±5% NO. OF PHASES 2 RATED VOLTAGE 2.0 V RATED CURRENT 5.0 A RESISTANCE 0.4 ohm±0.1   AT 25° INDUCTANCE 1.7 mH±20%    AT 1kHz, 1Vrms HOLDING TORQUE 1.6 N.m(226.2 oz.in)TYP. RUNNING TORQUE(AT --PPS) --V.DC, --A/PHASE DIELECTRIC STRENGTH 500V A.C/MIN. INSULATION RESISTANCE 100MΩ+/MIN. INSULATION CLASS CLASS B TEMPERATURE RISE 80K MAX. ROTOR INERTIA 480 g.cm²(2.64 oz.in²) WEIGHT APPROX. 1000g(35.0 oz) ALLOWABLE THRUST LOAD 15N ALLOWABLE RADIAL LOAD 75N(ON THE SHAFT END) OPERATION AMBIENT TEMP. ‘-20℃---+50℃ OPERATION AMBIENT HUM. 15%----90% LIFE 5000HOURS NEMA 23 STEPPER MOTOR TORQUE CURVE SPEED VS TORQUE CURVE MODEL: HEM-23C6403 LOT NO.: 181013 VOLTAGE 24V.D.C ○ SUPPLY WINDING CURRENT 4A/PHASE ○ rms AVE EXCITATION Full step DRIVE CIRCUIT UNIPOLAR # BIPOLAR INERTIA LOAD --g-cm2 If you want to know more kinds of stepper motor, please visit our website.

NEMA 23 DC Motor (SQUARE) NEMA 23 (square) shares similar mounting dimensions as NEMA 23 (round) but has much higher torque and power density. Due to the stronger magnet materials adopted, it improves better dynamic performance in the same space. NEMA 23 BRUSHLESS DC MOTOR (SQUARE) CHARACTERISTIC PARAMETER RATED VOLTAGE 30 VDC RATED OUTPUT POWER 30 W POLES NUMBER 8 PHASE NUMBER 3 RATED ROTATIONAL SPEED 3500 RPM OPEN LOOP IDLE SPEED 4000 RPM±10% RATED TORQUE 0.081N.m(11.4oz. n) RATED CURRENT 1.4 A VOLTAGE COEFFICIENT 0.073 V.s/rad PH RESISTANCE 0.93 ohm±0.15 AT 20°C PH INDUCTANCE 0.54 mH±20% AT 1kHz,1Vrms DIELECTRIC STRENGTH 500V A.C/MINUTE INSULATION CLASS CLASS E(120℃) ROTOR INERTIA 170g.cm 2 (0.93oz.in 2) WEIGHT APPROX. 900g(31.9oz) ALLOWABLE THRUST LOAD 15N ALLOWABLE RADIAL LOAD 75N(ON THE SHAFT END) OPERATE AMBIENT TEMP. -20°C----+50°C OPERATION AMBIENT HUM. 15%----90% LIFE 5000 HOURS If you want to know more stepper motor working principle, please visit our website. Now the price of stepper motor is affordable, if you have needs, please leave us a message.

NEMA 23 BRUSHLESS DC MOTOR (ROUND) nema 23 bldc (round) is the most popular size, as it reaches a better balance between size, power, and cost. We provide a good bldc motor price and please don't hesitate to contact us！ NEMA 23 Brushless Dc Motor (Round) Characteristic Parameter Rated voltage (VDC) 24 Rated power (W) 135 Body length (mm) 95 Pole pairs 2 Rated torque (Nm) 0.45 Rated current (A) 8 Rated speed (RPM) 3000 No load speed (RPM) 4300 Mass (kg) 0.55 Sensor Hall Working ambient (℃) -20°~ +80° Storage ambient (℃) +5 ~ +35 Working humidity (RH) 15%-90% If you want to know more types of stepper motor, please visit our website.

Actuator-Headlamp Leveling Headlight Adjustment Motor for Mondeo 12V /24V Please Note: Please be very careful to check our photos, make sure it is same as you wanted. Please feel free to contact with us if you are not sure whether it is suitable for your car. This Is Aftermarket Replacement Item But Not Genuine. Please Check Manufacturer's Part Number Before Ordering. OE number is characteristic number that identifies your part. You can find it on your old part or in your local dealer store. Specification Model WSD-JG-22 Name Headlight Adjustment Motor for Mondeo Voltage 12V /24V Installation (Internal / External) External Operation Function ESC Car Model Mondeo

The BHD - 180X2 engine and electirc motor driven hybrid anchor drilling rig is the latest developed drilling rig for our BHD drilling rig series. Product description: It driven either with diesel engine or electric motor,make it work more efficiently and more environmental friendly.With electric motor driven mode the drill rig can be operated without noisy and harmful emission,suitable to work in densely populated construction site.When electric power supply is not convenient the drive mode can be shifted to diesel engine.The usage of this drill rig is much wider.And the operation cost of this rig is much lower for the construction customers. Quick Detail: ① Type: Anchor Drilling Rig ② Power Type: Diesel Engine - Electric Motor ③ Feeding Mode: Cylinder + Chain ④ Motor: Double - Speed ⑤Torque range at low gear: 6800/13600Nm ⑥Torque range at high gear: 5800/11600Nm Advantage: 1.High quality 2.Long service life 3.Easy to operate 4.With competitive price,short lead - time

1 power module is required. Used to install q series modules. The application range is wider and more advanced. Q Series CPU products of Yudai. Q Series CPU products are widely used, Provide various CPUs of programmable controller, process, redundancy, C language, motion, manipulator and CNC to meet various control requirements. Through multi CPU configuration, a good system meeting various control requirements can be built according to the use scale and purpose. In addition, through the redundant system, a high reliability system can be built, and the system can continue to operate even in case of failure. A good network that matches the application purpose and purpose to realize seamless communication between layered systems. Strengthen information communication capacity through networking. This is also the network environment provided by Q series, a big topic in the automation field It is truly open & seamless. Including universal Ethernet Based "CC linkle control" controller network for easy management environment, And the "CC link Le field" field network that realizes high-speed and large capacity transmission under its management. It also includes Japan's initiative to meet the standards And has obtained semi certified field network "CC link", And the provincial distribution network "CC link/lt", which inherits its design concept, and supports the sensor network "anywire" Flexibly integrate all layers of the automation network with a full lineup. Input points: 32 points Input voltage and current: dc24v4ma. Response time: 1/5/10/20/70ms32 point 1 public terminal. Common anode. Output points: 32 points Output voltage and current: dc12-24v; 0.1a/ point; 2a/ public end Mitsubishi q65b. Response time: 1ms 32 points, 1 common end, leakage type; 40 pin connector. With thermal protection. Q65b with short-circuit protection and surge absorber Reduce startup time with sample tracking With the sampling and tracking function, it is convenient to analyze the data in case of failure, Test program debugging time, etc., can shorten the equipment fault analysis time and start-up time. In addition, it is also helpful to determine the data transmission and receiving time between CPU modules in a multi CPU system Mitsubishi q65b The collected data can be analyzed with programming tools The data changes of bit soft components and word soft components can be easily displayed in the form of charts and trend charts. In parallel, the sampling tracking results can be saved in CSV in the form of gxlogviewer and displayed through the recording data display and analysis tool gxlogviewer. High speed processing, shorter production time, better performance, As the application becomes larger and more complex, it is very necessary to shorten the system operation cycle time of Mitsubishi q65b. Through high basic operation processing speed of 1.9ns, the operation cycle can be shortened. In addition to realizing the high-speed control associated with single-chip microcomputer control in the past, it can also improve the system performance by reducing the total scanning time, Prevent any possible performance deviation. Easy to handle large volumes of data, In the past, it was impossible to realize the continuous access of file register areas of standard ram and SRAM card. When compiling, it is necessary to consider the boundary of each area and install an expansion board. 8MB SRAM expansion card is installed in the high-speed general-purpose qcpu. The standard RAM can be used as a continuous file register with a capacity of up to 4736k words, thus simplifying the programming. Therefore, even if the soft element memory space is insufficient, You can also easily expand the file storage area by installing an extended SRAM card. The index register is extended to 32 bits, so that the programming can go beyond the traditional 32K words, and the smaller modification can be extended to all areas of the file memory. In addition, the processing speed of indexing modification plays an important role in the operation of structured data (array), which has been improved. The scanning time can be shortened when the index modification is carried out in a thousand repeated processing programs (such as instructions from for to next, etc.). Input points: 16 points. Input voltage and current: dc24v6ma response time: 0/0.1/0.2/0.4/0.6/1ms. 16 points /1 common end. Common anode. 18 point terminal block. Easily connect programming tools through Ethernet, When the programming tool (GX works2.gx developer) is directly connected with the CPU (1 to 1), there is no need to set the p address, and there is no need to select the cable. Both the straight line and the cross line can be used. Therefore, this connection method is the same as using USB, which can easily communicate with the CPU. Even operators who are not familiar with network settings can easily establish connections. Modules with excellent performance Meet various control requirements from analog quantity to positioning. Q series module products include a variety of i/o, analog and positioning function modules. It can meet the control requirements of various industries and fields, such as input and output of switches, sensors, temperature, weight, flow, control of motors and drivers, and positioning of required control. It can also be used in combination with the CPU module to achieve appropriate control of q65b, constantly surpass and bravely climb the Q series. Strengthen the safety function. The file password of Mitsubishi q65b with a length of 32 characters can be set, In addition to English letters and numbers, special characters can also be used to further enhance the security of the password. In addition, only pre registered devices are allowed to access the CPU, thus blocking the access of unauthorized users, Therefore, it can prevent the outflow of important process assets and protect intellectual property rights,

Minimum Order: 1 bags

JYQD-V8.8 is very compact size BLDC motor driver board with necessary standard functions,its favorable price and reliable performance are competitive for industrial and commercial applications. Its widely applied by the worldwide clients almost for 8 years,its mature and stable design are competent for many applications. 1: Confirm that the voltage and power paraparameters of the motor not exceed the range as specified. 2:This driver board is used for 3-phase brushless sensorless motor, but not suit for all 3-phase brushless sensorless motors directly. If the driving effect is not good (such as starting jitter, reversing, the motor noload working current is too large, the speed is not stable, the efficiency is low, and can’t start-up with load.) Customers can adjust the resistance and capacitance of the driver board according to the actual situation to achieve the best driving effect (contact us for guidance)

Features: 1. Wide Speed Range, Flat Torque 2. Compact And High Power 3. Excellent Speed Stability 4. High Efficiency And Energy-Saving Wire Diagram: Type Color Functions UL1061 AWG26 Red Vcc Blue Ha Green Hb White Hc Black GND UL1061 AWG20/24 Yellow Phase U Red Phase V Black Phase W Driving Motor Specification: Item Unit JQ36RBL40-24-4818A JQ36BL57-24-4524A Number of poles 4 4 Number of Phase 3 3 Rated Voltage VDC 24 24 No-Load Speed rpm 7000 5800 Rated Speed rpm 4800 4500 Rated Torque mN.m 36 50 Rated Power W 18 24 Peak Torque mN.m 108 150 Peak Current A 3.7 4.1 Line to Line resistance ohms@20℃ 2.4 2 Line to Line Inductance mH 2.1 2.0 **Notes: Above is standard motor, we can be designed &manufactured with customized request!!

Electromagnetic contactor (contactor) refers to an electrical appliance that uses the current flowing through the coil to generate a magnetic field in industrial electricity to close the contact so as to control the load. The contactor is composed of electromagnetic system (armature, stator core, electromagnetic coil), contact system (normally open contact and normally closed contact) and arc extinguishing device. Structural composition Electromagnetic contactor is mainly composed of transmission device (electromagnetic mechanism), contact device (actuator) and arc extinguishing device. 1. Electromagnetic mechanism The electromagnetic mechanism includes three parts: moving core (armature), static core and electromagnetic coil. The electromagnetic coil is connected with current to generate electromagnetic suction and drive the contact to act. Electromagnetic mechanism is one of the important parts of electromagnetic contactor. The electromagnetic mechanism is composed of coil, iron core (static iron core), armature (moving iron core), pole shoe, iron yoke and air gap. The coil and iron core in the electromagnetic mechanism do not move in the working state; The armature is movable. The electromagnetic mechanism converts the electromagnetic energy generated by the electromagnetic coil into mechanical energy through the action state and action process of the armature and the corresponding mechanical mechanism to drive the contact to close or open, so as to realize the control purpose of the controlled circuit. 2. Contact device There are many structural forms of contact, which can be divided into: main contact and auxiliary contact according to the control circuit; The contact is divided into normally open contact and normally closed contact according to its original state; The contact is divided into bridge contact and finger contact according to its structural form. 3. Arc extinguishing device Arc extinguishing cover is an insulated and high temperature resistant arc extinguishing device made of clay and asbestos cement. It is a simple arc extinguishing device. When using the arc extinguishing cover device to extinguish the arc, the longitudinal seam arc extinguishing method is generally used in the arc extinguishing cover. Common arc extinguishing devices: arc extinguishing cover (arc resistant clay, asbestos cement and arc resistant plastic), arc extinguishing grid (arc resistant grid sheet copper plated thin steel sheet), magnetic blowing arc extinguishing device (an arc extinguishing coil is connected in series in the contact circuit). 4. Other components, including reaction spring, buffer spring, transmission mechanism and shell, etc.

Minimum Order: 1 bags

Product Description Single Phase 110V/220V Micro AC Motor Variable Speed Gear Motor with Speed Controller Product Features 1. High stability:Load power is sufficient, stable operation, and low fatigue after long term use. 2. Various function to motor. 3. Multiple voltage. 4. Wide power range. 5. Variable speed gear motor, compatible with speed controller MICRO AC MOTOR 6W 15W 25W 40W/60W 90W/120W 140W/160W 180W/200W 250W Reduction Ratio 3~200 3~200 3~200 3~200 3~200 3~200 3~200 3~200 50HZ Rated torque 0.13~3N.M 0.30~5N.M 0.50~8N.M 0.77~10N.M(40W) 1.19~20N.M(60W) 1.79~20N.M(90W) 2.25~20N.M(120W) 2.62~44N.M(140W) 2.76~44N.M(160W) 3.1~44N.M(180W) 3.44~44N.M(200W) 4.26~44N.M 60HZ Rated Torque 0.11~3N.M 0.25~5N.M 0.41~8N.M 0.64~10N.M(40W) 0.99~20N.M(60W) 1.49~20N.M(90W) 1.87~20N.M(120W) 2.19~44n.m(140W) 2.48~44N.M(160W) 2.76~44N.M(180W) 2.87~44N.M(200W) 3.83~44N.M MICRO DC MOTOR 60DC 70DC 80DC 90DC 100DC Reduction Ratio 3~200 3~200 3~200 3~200 3~200 Output Bearing speed 533~8 533~8 533~8 533~8 600~9 Rated torque 0.129~3n.m 0.26~5n.m 0.386~8n.m 0.52~20n.m 2.578~44n.m