Skeleton Oil Seal Manufacturer Providing OEM Industrial Sealing Solutions

In sealing systems, the skeleton oil seal (also known as a rotary shaft seal)
plays a critical role. It must not only prevent the leakage of lubricants but
also block the intrusion of external contaminants such as dust and moisture.
While many believe that sealing performance depends mainly on material and
structural design, the true core lies in the sealing mechanism at the lip and
the proper design of the interference fit.

This article provides a systematic analysis of the sealing mechanism and lip
interference design of skeleton oil seals from an engineering application
perspective, helping you avoid common pitfalls in selection and design.

Structural Parameters of skeleton oil seals

The structural design of a skeleton oil seal directly affects its sealing
performance and service life. Key aspects include:

Lip Type

Single Lip: Suitable for general sealing applications

Double Lip (with dust lip): Ideal for environments with external contaminants
such as dirt, water, or mud

Spring Inclusion

With Spring (e.g., TC, TB types): Provides continuous radial preload, suitable
for high-speed or high-pressure conditions

Without Spring: Used in low-speed, low-pressure, or static sealing applications

Lip Angle and Thickness These parameters influence oil film formation and oil
return capability, and are critical for achieving dynamic sealing performance.

Definition and Reference Range of Lip Interference

Lip interference refers to the dimensional difference between the oil seal’s
inner diameter in its free state and the actual shaft diameter. It determines
the contact pressure between the lip and the shaft, forming the basis of
sealing performance.

Typical Reference Range (for standard rotary oil seals)

Radial interference (single side): approximately 0.2 to 0.4 mm

Corresponding diameter interference: approximately 0.4 to 0.8 mm

Properly designed interference ensures effective sealing while minimizing
friction and wear, thereby extending service life.

Fit Parameters and Operating Conditions

Several factors significantly influence sealing performance in real-world
applications:

Shaft Surface Roughness: Recommended Ra between 0.2 and 0.8 μm. Surfaces that
are too rough or too smooth can destabilize the oil film.

Shaft Diameter Tolerance and Concentricity: Must meet standard specifications
to avoid eccentric wear.

Operating Speed and Temperature: High-speed or high-temperature conditions
require careful material selection and interference design.

Sealing Medium Characteristics: Lubricant viscosity and additives can affect
oil film behavior.

Sealing Mechanism: Dynamic Oil Film Sealing

skeleton oil seals do not rely solely on tightly compressed lips for sealing.
Instead, they function through a combination of mechanisms:

Initial contact pressure generated by lip interference

Formation of a thin oil film between the lip and the rotating shaft

The oil film reduces friction and creates an inward pumping effect

The spring provides continuous compensation for lip wear, maintaining stable
contact

This dynamic oil film sealing mechanism is the foundation of long-term,
reliable performance.

Common Issues Caused by Improper Interference

Excessive Interference

Increased friction and heat generation

Accelerated lip wear and shortened service life

Early failure under high-speed conditions

Insufficient Interference

Inadequate contact pressure and poor sealing

Unstable oil film, leading to leakage or oil flinging

Spring compensation may be insufficient to maintain sealing

Therefore, interference must be carefully balanced to ensure both sealing
effectiveness and durability.

Key Factors Affecting Interference Design

Shaft Speed: Reduce interference at high speeds to lower friction and heat
generation

Operating Temperature: Increase interference slightly in high-temperature
environments due to rubber softening

Sealing Medium: Low-viscosity fluids require more stable contact pressure

Rubber Material: Nitrile rubber suits standard designs; fluororubber requires
more precise interference

Spring Inclusion: Seals with springs are less dependent on body interference
and offer greater adaptability

Typical Application Scenarios

skeleton oil seals are widely used in the following rotary sealing
applications:

Automotive engines, transmissions, and electric drive systems

Industrial motors, pumps, and fans

Gearboxes, drive shafts, and various mechanical shaft ends

In these environments, oil seals must not only prevent lubricant leakage but
also maintain stable performance under high-speed, high-temperature, and high-
pressure conditions.

The sealing performance of a skeleton oil seal depends on both a well-designed
lip structure and precisely calculated interference. Together, they form a
stable oil film sealing system that ensures efficient and reliable equipment
operation.

In practical engineering, it is recommended to consider operating conditions,
shaft dimensions, and material properties when designing and verifying
interference. Only through scientific interference design can the optimal
balance between sealing reliability and service life be achieved.

If you are currently working on oil seal selection, sealing structure
optimization, or troubleshooting sealing failures, feel free to reach out.
Let’s explore more efficient solutions together.

Minimum Order: 1000 pieces

Click to Enlarge