Import-Export Bulletin Board Post an Offer to Sell

New here? Please subscribe
to post trade leads. It's FREE!

Chemical Equipment & Lab Supplies


Home > Offers to Sell > Chemicals & Plastics > Chemical Equipment & Lab Supplies

Browse leads by category:
    
    
  
 

Summary of 1/22/22 9:33 GMT:>> Show Compact View
1/29/21 7:30 GMT
dual temperature zone tube furnace with magnetic push rod

CY-O1200-60II IT-MB Double temperature tube furnace with magnetic push rod The dual-temperature zone tube furnace is equipped with a magnetic push rod, which has an exquisite structure and high reliability, and can perform displacement operation on the sample in the tube while keeping the furnace tube vacuum tight. Combined with separate temperature control in dual temperature zones, it can realize a variety of heat treatment processes for users and is an ideal equipment for material research and material processing. Technical parameter Supply voltage: AC220V, 50Hz Maximum power: 4KW Heating rate: Maximum 20℃/min, recommended ≤10℃/min Operating temperature: Maximum temperature≤1200℃; continuous working temperature≤1150℃ Heating temperature zone: Dual temperature zone 200mm+200mm Furnace tube parameters: Length 1000mm O.D 60mm I.D 57mm Temperature control: PID temperature control accuracy ±1℃ Thermocouple: K type thermocouple Temperature control method: Separate temperature control in dual temperature zones AI-PID 30-segment process curve, can store multiple With overheating and broken couple protection Furnace material: High purity alumina furnace Vacuum interface: KF16 Air inlet: 6.35 Card sleeve connector Magnetic putter: Moveable length 500mm Can shift samples in two temperature zones To meet customer's heat treatment process,Using magnetic coupling connection,Can ensure the vacuum of the furnace tube while pushing the sample Dimensions: 1300mm X 420mm X 550mm

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 7:25 GMT
dual zones sliding rotation tube furnace with vacuum pump

Dual zones sliding rotation tube furnace This product is a double temperature zone slide tube furnace. There is a mixing partition board in the middle of the furnace tube, which can mix the powder and particles repeatedly with the rotation of the furnace tube. Through the mechanical drive, the working pipe can rotate 360°continuously, so that the materials in the tube can be mixed and heated evenly. The furnace body can slide back and forth on the support to realize rapid temperature rise and fall. Two way float flowmeter can be used to inject two kinds of gas into the pipeline; high performance mechanical pump can quickly pump furnace tube to vacuum; through the cooperation of pump and flowmeter, a variety of CVD processes can be realized.The rotating device is very suitable for continuously wrapping and modifying powder materials by CVD method in an atmosphere protected environment. Technical Parameters ►Dual zones tube furnace Model: CY-O1200-60IIT-R Power: 3KW Tube material: High purity quart Tube diameter: 60mm Tube length: 1600mm Chamber length: 440mm Heating zone length: 200mm+200mm Working temperature: 0~1150℃ Limit temperature: 1200℃ Control accuracy: ±1℃ Temperature control mode: 30 or 50 segment program temperature control Display mode: High definition full color LCD touch screen Sealing mode: 304 stainless steel vacuum flange Power supply: AC:110V 50/60Hz 2.5kW Slide rail: 2030mm, sliding range 1500mm Rotation speed: 0~20rpm ►Flowmeter Model: CY-2F Number of gas paths: 2 channels Type: float flowmeter Range: Route a: 0~160mL/min; route B: 0~100mL/min;Accuracy 4% Pipeline pressure: Stainless steel pipe with pressure of 3Mpa Flowmeter pressure: 1 standard atmospheric pressure Pipeline interface: φ 8mm quick screw connector ►Vacuum system Vacuum pump: Two stage rotary vane pump Pumping speed: 1.1L/s Suction connection: KF16 Pump limit vacuum: 10E-1Pa power supply: AC110V 50/60Hz

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 7:18 GMT
1200 ℃ high vacuum tube furnace with sliding rail for rapid annealing

1200℃ high-vacuum rapid annealing furnace 1.Overview The 1200℃rapid annealing furnace is essentially a set of slideway furnace, which realizes the functions of heating and annealing. The intake end is equipped with a high-precision three-way mass flow meter to accurately control the atmosphere in the tube;At the same time, the equipment is equipped with a turbo molecular pump, which can quickly achieve a high vacuum environment and maximize the interference of the air atmosphere to the experiment. The slideway furnace is composed of 1200℃standard single heating zone tube furnace and high precision slide rail.Tube furnace adopts resistance wire heating, combined with polycrystalline fiber furnace chamber, which has excellent temperature rise and thermal insulation performance. The slide rails are tightly matched, slide smoothly, and easy to operate. At the same time, it adopts full-color LCD touch screen operation, which is simple and intuitive, easy to use, can simplify the experimental operation and save the test time. 2.Technical Parameters ►1200 ℃ Tube furnace Voltage: AC220V,50Hz Max power: 4KW Heating zone: Single zone 440mm Working temperature: ≤1200℃ Temperature control accuracy: ±1℃ Temperature control method: AI-PID 30-stage process curve, can store multiple Tube material: High purity quartz Tube size: φ80mm I.D x 1000mm L Sealing mode: Stainless steel vacuum flange Vacuum measurement: Mechanical pressure gauge Working gas: Non-corrosive gases such as hydrogen, nitrogen, argon, and oxygen ►Three-way mass flowmeter Valve type: Stainless steel needle valve Gas channels: Three-way Pressure range: 0.05~0.3MPa Range: 0~100 SCCM (H2)/0~200 SCCM(Ar)/0~500 SCCM(CH4) Flow control range: ±1.5% Mixing tank volume: 750mL Gas path material: 304 stainless steel Pipe interface: 6.35mm Bite type joint Power supply: AC220V 50Hz

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 7:06 GMT
lab mini high temperature high pressure tube furnace

Mini high pressure tube furnace CY-H1200-1L high pressure tube furnace is mainly composed of three parts: heating system, high temperature and high pressure furnace tube and pressure measurement and control system. It can realize the three functions of automatic stamping, overpressure release and automatic temperature control. It is also equipped with process software, which can realize the whole collection of data during the sintering process, and provide the most true and reliable basis for the analysis and research of experimental data. The equipment can be widely used for high temperature and high pressure processing of nano materials, high temperature and high pressure sintering of special functional ceramics, and this high temperature and high pressure modulation method is used to change the thermal properties and electrical conductivity of the materials. Technical parameters: Supply voltage: AC220V/110V, 50Hz/60Hz Total power: 2KW Operating temperature: ≤1100℃ Heating rate: Suggest 10℃/min Thermocouple type: K-type thermocouple Furnace tube size: O.D.φ60mm I.D φ25 xφ L. 600mm Furnace tube material: Super high temperature alloy Sealing flange: Pressure flange Pressure measurement: Semiconductor pressure gauge Overvoltage protection: Safety vent valve Heating zone: Single heating zone 200mm Temperature control 1) PID automatic control of heating rate, cooling rate and holding time 2) PID control over temperature protection and thermocouple failure protection 3) It has over-temperature protection alarm function, so the equipment can run unattended 4) The temperature accuracy is ±1℃ (the difference between the displayed temperature and the actual temperature) 5) AI-PID 30-segment process curve, can store multiple 6) Temperature control accuracy ±1℃ Work pressure ≤4Mpa @800℃ ≤2.5Mpa @900℃ ≤1.2Mpa @1000℃ ≤0.8Mpa @1100℃ Working gas: Non-corrosive gases such as nitrogen, argon, and oxygen

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 7:04 GMT
Vacuum Atmosphere Rotary Tube Furnace With automatic feeding and collecting

Vacuum Atmosphere Rotary Tube Furnace With automatic feeding and collecting equipment The tube furnace CY-O1200-R100IT-AF is a rotatable tube furnace with automatic feeding and collecting equipment. It adopts double-layer air-cooling structure, the surface temperature of the furnace body is ≤60℃, and it adopts high-purity alumina polycrystal. The furnace made of high purity alumina polycrystalline fiber, and the heating element is imported heating wire, which can prolong the service life of the furnace. The structure of the whole machine is reasonable, the shape is unique, the operation is simple and easy to learn. It is an ideal product for sintering, melting and analyzing metals, non-metals and their compounds under multiple atmospheres or vacuum conditions. The furnace tube of the device can be rotated at a speed of 0 to 10 rpm, and the furnace body can be inclined with respect to the plane at an angle of 0 to 10° to complete the collection process after the reaction. Technical Parameters Voltage: AC220V, 50Hz Power: 7.5 kW Furnace Structure: Double-layer air-cooling structure, keep the temperature≤60℃ Tube material: High purity quartz tube Heating zone length: 400mm Tube size: φ100*1500mm Heating element: import alloy wire Max temperature: 1150℃ Working temperature: ≤1050℃ Temperature stability: ±2℃ Heating rate: suggest 10℃/min Temperature control accuracy: ±1℃ Thermocouple: K type Temperature controller: With touch screen control, multiple heating curves can be pre-stored. The heating curve is automatically controlled by the program PID. Each curve contains 30 programmable steps, which can precisely control the heating rate, cooling speed and dwell time. Built-in PID automatic adjustment function, thermal disconnection thermocouple disconnect protection, over temperature protection and alarm. Automatic feeder: mounted on the furnace via vacuum sealed. Feed rate ≤97cm3/min, gas can be inleted to protect the material. Automatic gather tank: capacity 5L, use for gather the material after reaction, gas can be inlet to protect the material. Tube rotation speed: 0~10 rpm Furnace tilt angle: Left 0~10° Warranty: 12months

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 6:57 GMT
large-size 200mm diameter rotary tube furnace for lab

Rotary furnace/ Rotary kiln This equipment is a rotary furnace, equipped with a large-size furnace tube with a diameter of 200mm, and is equipped with a feeding mechanism and a rotating mechanism to ensure continuous and uniform reaction. The laboratory rotary furnace is widely used in lithium battery materials (including lithium iron phosphate, lithium cobalt oxide, lithium manganese oxide, lithium nickel cobalt oxide, cobalt oxide, cobalt powder, nickel powder and other positive and negative electrode materials), rare earth Materials (rare earth oxides, luminescent powder, polishing powder), magnetic materials, kaolin mineral materials, glaze pigments, ceramic equipment, Active refractory materials, catalyst materials (vanadium, vanadium tetroxide, vanadium iron, etc.) carbonization, metal powder calcination, etc. It is suitable for experiments or small batch production in experimental testing institutions, universities and colleges, scientific research institutes, industrial and mining enterprises. Technical parameters: Model: CY-SH40 Power supply: AC380V 50Hz 45kW Productivity: 0-40kg/h Max. working temperature: 500℃ Furnace tube size: φ200mm x 600mm Tilt angle: 0~10° continuously adjustable Rotation speed: 0~3.3rpm Dimensions: 1800mm x 870mm x 1750mm Temperature control accuracy: ±1℃ Temperature control method: AI-PID 30-segment process curve, with overheat and thermocouple failure protection Furnace tube material: High purity quartz

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 6:53 GMT
3 zone 1200℃ horizontal split type high vacuum tube furnace

1200C High vacuum nickle base alloy tube furnace KEY:electrically heated, high vacuum, three (03) zone, horizontal, split type (for Rapid Cooling), tubular furnace Technical Specifications ►A.Heating of Furnace Working Temperature 1150 °C Heating Zones 3 Length of Each Heating Zone 300-400mm Length of Uniform Temp Zone 500 mm (Minimum) Material of Heating Elements Kanthel Vacuum tight tube material Inconel 600 or equivalent Nickle base alloy suitable for above mentioned Temperature. Water cooling jackets on both ends of the working tube to be provided. Inside dia. of working tube 100 mm (Minimum) Wall thickness of working tube 5 mm (Minimum) Temperature uniformity ± 5°C (In Uniform Temperature Zone) Temperature Control independent Eurotherm Programmable PID controllers (One for each heating zone), Note: The temperature controllers must be selectable for all types of thermocouple. Safety Controller A safety controller must be installed in the furnace to shut off the furnace in case of temperature shooting due failure of temperature control, Thermocouples: K type thermocouples for controlling/ measuring the temperature of heating zones ►B.Vacuum in Furnace High vacuum to be generated by rotary vane pump and oil diffusion pump incorporated in a vacuum station. The valves in the vacuum station are to be operated manually. Two stage rotary vane pump Suction capacity: 5L/s; Ultimate vacuum:1x 10-3 mbar Oil Diffusion Pump Suction capacity: 600L/s; Ultimate vacuum: 1x 10-6 mbar Vacuum Gauge & Controller Vacuum gauge fitted in the working tube should be able to measure the vacuum during heating operation of the furnace. Measuring range: 1x 10-9 mbar ►C.Electrical System Heating 380V, 3 phases, 50Hz, Approx. 45KVA Vacuum 220V, single phase, 50Hz

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 6:39 GMT
Vertical Tube Furnace with Ultrasonic Spray Nozzle and Solid Powder Feed

Ultrasonic Spray Pyrolysis System within 4" Vertical Tube Furnace with Spray Nozzle and Volumetric Solid Powder Feeder is Two Heating Zone Split Vertical Tube Furnace with vacuum sealed 100mm diameter quartz tube.It can introduce gas flow or liquid/ water atomization to the heating furnace, also be used for PVD, CSS or CVD coating. Two precision temperature controllers provide 30 segments heating and cooling program with +/- 1C accuracy independently. The vertical tube furnace is installed in a heavy-duty mobile cart for easy moving. ►Furnace Structure Two Heating Zone Split Vertical Tube Furnace for longer and uniform constanttemperature zone The ultrasonic spray nozzle can make liquid/water atomized via gravity and low- pressure compressed air. Volumetric Feeder for feeding solid powder into a furnace to form core/ shell structure  ►Upgrade If you need a horizontal furnace, we will change to the same specification tube furnace at no cost.You could upgrade from 40KHz to 3 KW and 120 KHz,  Ultrasonic Spray Nozzle at extra cost ►Power for Furnace 6KW (total) / each zone: 3KW ►Voltage AC 208-240V Single Phase, 50/60 Hz ►Max. Temperature 1200°C (<1 hr) each zone ►Continuous Temperature 1100°C for each zone ►Max. Heating Rate <= 20°C/min. ►Temperature Accuracy +/- 1°C ►Tube Size and Materials One 1000mm length quartz tube is included,OD: 100 mm, ID. 95 mm Foam ceramic blocks with alumina coating are included, which is hanged on top of flange to protect O-ring damaged by heat radiation ►Heating Zone Length:200mm ( bottom )//200mm ( top )//400mm ( total ) ►Constant Temperature Zone Constant temperature zone: 300 mm (+/-1°C) if two heating zones are at the same temperature ►Temperature Controller MET certified 30 programmable segments for precise control of heating rate, cooling rate and dwell time. Built in PID Auto-Tune function with overheating & broken thermocouple broken protection. Over temperature protection and alarm allows for operation without attendant(s). RS485 Communication Port. ►Vacuum Sealing Flange Two stainless steel flanges with vacuum gauge and valves included A hook ring is welded inside the top flange for hanging thermal block or crucible by wire Gas outlet ( vacuum port ) on top with 1/4" barb connector.  Gas inlet on bottom with 1/4" barb connector ►Vacuum Level 10E-2 Torr by mechanical vacuum pump 10E-5 Torr by molecular pump Leak rate < 5 mTorr / min. ►Heating Element 1300°C Fe-Cr-Al Alloy doped by Mo ►Dimensions 550mm(L) x 380mm(W) x 520mm(H) exclude mobile cart 600mm(L) x 600mm(W) x 1200mm(H) install with mobile cart ►Net Weight About 80 kg (excluding mobile cart) ►Warranty One year limited warranty with lifetime support 

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 6:26 GMT
Halogen lamp RTP annealing furnace with real substrate temperature measure

The halogen lamp RTP annealing furnace is a 6-inch wafer rapid annealing furnace. It adopts innovative heating technology to realize real substrate temperature measurement. It does not need the temperature compensation of traditional rapid annealing furnaces. The temperature control is accurate and the temperature is highly repeatable. Customers include many international semiconductor companies and well-known scientific research teams. It is an ideal choice for semiconductor annealing process. Technical features: • Real substrate temperature measurement without traditional temperature compensation • Infrared halogen tube lamp heating • Extremely excellent heating temperature accuracy and uniformity • Fast digital PID temperature control • Stainless steel cold wall vacuum chamber • Good system stability • Compact structure, small desktop system • PC control with touch screen • Compatible with normal pressure and vacuum environment, the standard value of vacuum degree is 5×10-3 Torr, and the vacuum degree is as low as 5×10-6 Torr using two-stage molecular pump • Up to 3-channel gases (MFC control) • No cross contamination, no metal contamination. Introduction of real substrate temperature measurement technology: As shown in the figure above, the heat radiated by the array halogen lamp reaches the surface of the sample through the quartz window, and the sample is heated. The traditional rapid annealing furnace uses a thermocouple to measure the substrate temperature. Because the thermocouple is at a certain distance from the substrate, the measurement is not the substrate. The real temperature of the chip must be temperature compensated. The halogen lamp RTP annealing furnace uses a dedicated flake-like Real T/C KIT for temperature measurement, as shown in the figure above, the contact thermometer is connected to the flake-like Real T/C KIT. The flake-like Real T/C KIT is located very close to the sample above when working, the array halogen lamp radiates heat to the sample surface through the quartz window, the sample is heated, and the flake-like Real T/C KIT is heated at the same time. Because the substrate is very close to the Real T/C KIT, there will be heat transfer between them, and the thermal equilibrium will be quickly reached, so the temperature measured by the flake-like Real T/C KIT is infinitely close to the real temperature of the substrate, thus realizing the real measurement of the substrate temperature. Technical parameters: Substrate size 6 inches Substrate base Quartz needle (optional SiC coated graphite base) Temperature range 150-1250℃ Heating rate 10-150℃/S Temperature uniformity ≤±1.5% (@800℃, Silicon wafer) ≤±1.0% (@800℃, Substrate on SiC coated graphite susceptor) Temperature control accuracy ≤ ±3℃ Temperature repeatability ≤ ±3℃ Vacuum 5.0E-3 Torr / 5.0E-6 Torr Gas supply Standard 1 channel N2 purge and cooling gas circuit, controlled by MFC (up to 3 channels can be selected) Annealing duration ≥35min@1250℃ Temperature control Fast digital PID control Dimensions 870mm*650mm*620mm Substrate type: • Silicon wafers • Compound semiconductor wafers • GaN/Sapphire wafers for LEDs • Silicon carbide wafers • Poly silicon wafers for solar cells • Glass substrates • Metals • Polymers • Graphite and silicon carbide susceptors Application areas: Ion implantation/contact annealing, rapid thermal processing (RTP), rapid annealing (RTA), rapid thermal oxidation (RTO), rapid thermal nitridation (RTN), can be used in different environments such as vacuum, inert atmosphere, oxygen, hydrogen, mixed gas, etc. SiAu, SiAl, SiMo alloying, low dielectric materials, crystallization, densification, solar cell bonding, etc.

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 6:22 GMT
1200℃ vacuum vertical tube furnace for quenching

CY-1200X-4-VTQ is a vertical quenching furnace, the main body is an open type vertical tubular furnace, the flange on the furnace tube is equipped with hook and plug, which can be manually released to make the hanging sample fall down; the lower flange is connected with the sealed liquid container through a φ 100 mm flange, and the liquid container can contain ice water or cold oil. High purity alumina is used as furnace material in tubular furnace, which can improve thermal efficiency and service life of furnace. Rotary vane mechanical pump is used in vacuum pump, which can provide vacuum environment for vacuum quenching. The liquid container is of double-layer structure, with excellent vacuum pressure resistance and reliable sealing. The box body is fixed by jacking wire and equipped with a liquid outlet valve, which is convenient for sampling and changing liquid. Application The equipment is suitable for studying phase transformation and microstructure properties of materials. Technical parameter 1. Model CY-1200X-4-VTQ 2. Power supply Voltage:220V 50Hz power:3KW 3. Heating element Alloy resistance wire 4. Temp zone length 440mm,constant temperature zone 200mm 5. working temperature Max1200℃(<1h),continuous working 1100℃ 6. Heating rate ≤20℃/min,recommended ≤10℃/min 7. Thermocouple K-type 8. Temperature control PID temperature control system, accuracy±1℃; Multi stage temperature control program can be set to accurately control heating and cooling rate and constant temperature time; It has overheat and broken couple protection 9. Tube Material: high purity quartz; Size: O.D φ 100mm i.d94mm x l.1000mm 10. Vacuum flange Upper flange:Φ 100 vacuum stainless steel flange with manual hook opening device 11. Lower flange:Vacuum stainless steel flange with CF100 flange adapter 12. Quenching vessel Double shell, with outlet valve

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 6:21 GMT
1600C Horizontal Flash Sintering Furnace with 3KW Programmable Power Source

1600C Horizontal Flash Sintering Furnace with 3KW Programmable Power Source CY-1600X-FS3KW is a horizontal tube furnace with 3KW programmable AC power source designed for exploring the flash- sintering for ceramic materials at a lower cost.The tube furnace comes with 80mm OD alumina tube and a sliding sample fixture, which can preheat sample up to 1600oC. The Sample holder will press electric wire to the sample via ceramic screw to pass through programmable AC power source which is programmable up to 1500W power. Flash-sintering is an new technology which is used widely in the research of solid state electrolyte, SOFC and fero-magnetic & Thermo-electric materials. Tube Furnace 208 - 240 VAC, 50/60Hz,  5.2 KW max. power consumption Working temperature:  1600°C continuous and 1700°C Max. Heating Zone length: 18" ( 457 mm ) Constant temperature zone: 6"  ( 150 mm) within +/- 1°C Temperature Control PID automatic control via solid state relay with 30 steps programmable and  +/-1°C accuracy Built-in Over Temperature and Thermocouple Failure Protection B-type thermal couple Vacuum Sealing Flanges & Sample Fixture Vacuum Flanges are made of stainless steel which can reach the vacuum to 10-2 torr by mechanical pump and 10-5  torr by turbo pump. Left Side Flange: 30 mm dia. Quartz observation window  Needle valve with 1/4 NSP connector Right Side Flange: KF25 vacuum port to connect to a vacuum pump Two electric wires feedthrough. Wires are made of Platinium with 1 mm diameter Needle valve with mechanical vacuum gauge. Sample fixture is built-in the inside flange. This flange is slidable to make sample loading easy. Programmable AC Power Source The programmable AC power source is to connect the electric wire at the feedthrough at the right side flange.  After pre-heating,  AC power will pass a sample as programa setting to produce more heat rapindly, which results in sample sintered in high density.  The power parameters can be set via included labtop. Power source specifications ae as the below Input Voltage: AC220V±10%,  50/60Hz, single phase Power Capacity:  3000 W Max. Circuit Type: IGBT, PWM Output Voltage: 50V-300V adjustable with ≤1% stability Output Frequency:      50/60Hz fixed with ≤0.01% stability Protection:   Overload, over temperature , and short circus PC programmable:Laptop with pre-installed software is included for program setting Optional :       DC power  source 400V/10A is available upon request at the extra cost Dimensions & Weight:1950L×500 W ×720 H, mm;150Kg Warranty: One year limited warranty with lifetime support (Consumable parts such as tubes and o-rings are not covered by the warranty)  Compliance:CE Certified

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 6:06 GMT
20T 1600℃ SPS spark plasma sintering furnace

Spark plasma sintering furnace (SPS) (20t, 1600 ℃) Plasma spark sintering (spark) is a new technology for rapid consolidation of powders. SPS uses a high current pulse power supply to stimulate and promote the consolidation and reactive sintering process. Compared with the traditional technology, SPS can adjust the density of all kinds of conductor, non conductor and composite materials to any required value. SPS shortens the experimental time and energy consumption to the greatest extent, while maintaining the micro nano structure perfectly. Therefore, since its birth, it has rapidly become an important tool in scientific research, new material research and development, industrial production and other fields The highest temperature of spark plasma sintering system can reach 1600 ℃. It can be used for material annealing, material hot pressing bonding, surface treatment and synthesis, etc. The samples can be metals, ceramics, nano materials and amorphous materials. This device is especially suitable for the research of solid electrolyte and thermoelectric materials Specification ►Configuration , Stainless steel vacuum chamber Hot pressing system DC pulse power supply Vacuum system Hot pressing control system ►Power 20 KVA ►Input Voltage AC380V 50 Hz Three Phases ►Output Current DC 0~1500 A (Digital Controlled) ►Output Voltage DC 0~10 V (Digital Control) ►Pulse Frequency 5~255 ms Adjustable2~1000 Hz adjustable ►Maximum Tem  1200ºC with K-type thermal couple 1600ºC with B-type thermal couple Two types of thermal couple are included ►Temp controller  Precision Eurotherm temperature controller is built in At the fastest heating rate, the over-temp is less than 3℃ Temperature accuracy : < 0.1ºC ►Hydraulic Press  Manual operated hydraulic press to apply pressure. Max pressure: 20 T Digital Pressure guage is built in with over-pressure alarm. ►Sintering Die Set Dimension Equipped with hot isostatic graphite mould (made in Japan) Diameter of die core: 12-50mm (customized according to customer requirements) The maximum allowable pressure is 50MPa, and the maximum allowable pressure is determined by the diameter of the mold core The maximum pressure of the 1/2 inch die core is 0.5T The maximum pressure of 1 inch die core is 3T ►Sintering Stroke 100 mm ►Vacuum Chamber  Square stainless steel cavity body Double-layer cavity, which needs to be supplied with cooling water ►Max Vacuum Level (Room Temp)  10 Pa (7.5 x 10^-2 torr) with the mechanical pumpOne double stage mechanical pump is included 1 Pa ( 10x10^-4 torr ) with optional turbo pump ( click picture below right to order ) ►Max Heating Rate 300ºC/min ►Water Cooling a circulating water cooling machine with a flow of 58L/min ►Standard Accessories SPS Sintering Graphite Die Set Graphite Spacer K & B type Thermal Couples rings Clamping Tool ►Dimension Power Supply :760 L X 460 W X 1820 H, mm Furnace:970 L X 720 W X 1400 H, mm ►Compliance  CE certified ► Warranty: One year limited warranty 

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 5:54 GMT
1600ºC 5T Vacuum Rapid Heated Press Furnace

Rapid Heated Pressing (VRHP) Furnace upto 1600ºC & 5T with Stainless Steel Vacuum Chamber OTF-1700X-RHP4 is a Vacuum Rapid Heated Pressing Furnace (VRHP or RHP) designed for making dense pallets under vacuum or the protective gas environment. A 15 kW temperature controllable induction heater is integrated into the system, which provides sufficient power for rapidly heating the graphite pressing die up to 1700 ºC. The Induction coil is built inside of stainless steel vacuum chamber. An electric hydraulic press is inserted from the bottom of the chamber, providing up to 5 tons pressing force. ▶Max. Pressure 5 metric tons (10 MPa on pressure gauge). ▶Hydraulic Electrical Presser Piston diameter: 60 mm. Vertical move distance: 35 mm. Automatic pressure controller ▶Induction Heater Working voltage: 380 VAC, 50/60 Hz, three phase. Working current: 40 A (with a 60 A breaker). Maximum oscillating power: 30 kW. Maximum input power: 15 kW. Output frequency: 30 ~ 80 kHz. Duty cycle: 80%. Max. Working Temperature :  1600 ℃ max duration time: < 30 min. Air cooling: fan. Protection: water pressure monitoring, high-temperature protection, and overpower protection. ▶Temp. Controller Working voltage: 208 ~ 240 VAC, single phase. Precision digital temperature controller with automatic PID tuning. Temperature profile that contains maximum 30 programmable segments to control heating, dwelling, and cooling. Overheating and pyrometer failure protection. Temperature accuracy: ± 10 ºC.  B-type thermocouple. Continuous working temperature range: 1000 ~1700 ºC. Experimental maximum heating rate in vacuum (only for 0.5" inner diameter graphite pressing die; without any thermal block):  ▶Processing chamber&Sealing Flange Stainless steel vacuum sealed chamber: 260 × 230 × 320 mm (OD × ID × L).  Flanges on both ends of the chamber. Flanges have a tunnel for cooling water. Equipped with a KF-25D vacuum port, pressure gauge, 1/4" gas inlet port with stainless steel needle valve. The upper flange can be lifted by raising the lead screw which provides the easy access to retrieve the graphite die. Requires at least 55 liters per minute water flow.           ▶Digital Pressure Gauge Maximum pressure display is upto 10 MPa. ▶High-Temperature Graphite Pressing Die Set  Two built-in graphite supporting rods. One set of 0.5" (inner diameter) graphite die are included for immediate use. Made of high purity graphite by HIP processing, Max. Pressure for the die is 50 MPa, and Max. Load from the hydraulic press is dependent on die 's ID 0.5"ID   Max.  0.5T 1.0 ID:   Max.  3T ▶Dimensions 800 × 800 × 1300 mm (L × W × H).   ▶Net Weight 350 kg. ▶Application Notes the gas cylinder must have a two-stage pressure regulator to limit the pressure below 3 psi for safe operation. ▶Warranty One year limited standard warranty 

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 3:47 GMT
1200°C box-type 64 Liter hydrogen atmosphere furnace

Low temperature box hydrogen furnace This product is a box-type furnace with a hydrogen atmosphere at 1200°C. The furnace chamber is a closed design, which can be vacuumed and filled with hydrogen and other gases. The furnace is a double-layer stainless steel structure, which guarantees vacuum and safety to the utmost extent, ensures that the positive pressure can reach 0.06MP, and the vacuum can reach -0.09MPa; the overall water cooling is cooled, and the shell temperature does not exceed 50℃ during heating to ensure safe operation. Built-in H2 combustion control system, that is, when the controller does not detect the flame in the burner, the gas delivery valve will automatically close. The furnace uses five-sided heating, and the temperature distribution in the furnace is the most even. This box furnace contains FA-YD518P-AG temperature controller, which can realize proportional integral differential control and automatic adjustment functions. The temperature control accuracy is ±1℃, and it has built-in over-temperature alarm and thermocouple failure alarm. Technical parameters: ● Product model CY-M1200H-64IT ● Supply voltage AC220V, 50Hz ● Total power 10KW ● Operating temperature ≤1200℃ ● Heating rate Suggest 10℃/min ● Thermocouple type B type thermocouple ● Furnace size 400x400x400mm, 64Liter ● Maximum sample load 35kg ● Constant temperature zone ±1℃ in the center 250mm 3 area; ±5℃ in the center 300mm 3 area ● Temperature control 1) PID automatic control of heating rate, cooling rate and holding time 2) PID control over temperature protection and short couple protection 3) It has over-temperature protection alarm function, so the equipment can run unattended 4) The temperature accuracy is ±1℃ (the difference between the displayed temperature and the actual temperature) ● Heating element 1300℃ imported heating wire ● Water chiller 16L/min circulating water chiller

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China
1/29/21 3:28 GMT
Bridgman Crystal Growth Furnace with Hanging Wire Mechanism Up to 1100℃

Compact Bridgman Crystal Growth Furnace with Hanging Wire Mechanism Up to 1100C CYKY-1200X-S-VT-BMGH is a compact and economic 1200ºC Maximum Bridgman crystal growth furnace with 2" quartz tube and precision hanged wire travel mechanism, which is designed for growing small size crystal under control atmosphere or sealed quartz crucible at low cost. Vertical Two Zone Tube Furnace 1. Compact two zones split vertical tube furnace 2. Working Voltage: 110V AC or 220V selectable 3. Max. Power Consumption: 1.5 KW 4. Two Heating Zone: 100 mm L for each Zone, 200 mm L in total  5. Max. heating temperature: 1200°C 6. Continuous working temperature: 1100°C 7. Two programmable digital temperature controllers which control two heating zone independently 8. Max. Temperature gradient: 1ºC/Cm 9. Finding a suitable thermal gradient is user responsibility 10. Adjusting two heating zone's temperature can create different thermal gradient profile 11. Adjusting furnace opening diameter also can change the thermal gradient 12. Quartz tube (2" quartz tube (50mm O.D x 44mm I.D x 600mm L) is included with sealed flange) Hanging wire 1. One set of Ni-SS hanging wire is included (pic to the left). Max. working temperature is 800C. 2. Optional hanging wire for higher working temperature is available upon request: 3. Ni-Cr-Al wire (not included) Max. working temperature < 1100°C 4. Platinium wire (not included) Max.working temperature > 1200°C and < 1600°C 5. A thin hanging wire goes through the top flange. A positive inert gas can keep processing tube under controlled atmosphere 6. For air-sensitive material, the sample shall be sealed in a small quartz tube with pre-vacuumed as Pic below right 7. 800C pulling wire (Ni-SS)        sealed quartz tube as the crucible  Motor and Controller 1. 6"L x 4"W Touch Screen 2. Wire descending speed is programmable within 3 segments. 3. Precise DC stepper motor controls traveling speed. 4. Pulling  speed range: 1-500 um/sec adjustable  with the accuracy of +/- 0.05%  5. Total stoke length controlled by touch screen: 350mm 6. Power: 50W, 110V - 240V C Optional:   Lower speed range is available upon request at extra cost.  Product Dimensions :520mm (L) x 430mm (W) x 1100mm (H) Compliance:CE Certified/NRTL certification is available upon request at an extra cost Warranty:One Year limited warranty with lifetime support Consumable parts such as processing tubes, O-rings, and heating elements are not covered by the warranty

Minimum Order: 1 bags

Contact:
Phone:
Fax:
Email:
iris zhang
+8637155199322

Send Inquiry
Zhengzhou CY Scientific Instrument Co., Ltd.
No. 820, 8th Floor, 1st Unit, 9th Block, Cuizhu Street, High-Tech Zone, Zhengzhou, Henan, China
Zhengzhou 450000
China


SOURCE: Import-Export Bulletin Board (https://www.imexbb.com/)
Result Page:   << Previous   |   1  |   2  |   3  |   4  |   5  |   6  |   7  |   8  |   9  |   10  |   11  |   Next >>

Post an Offer to Sell
Home - Offers to Buy - Business Opportunities - Company Profiles

© 1996-2022 IMEXBB.com. All rights reserved.

IMEXBB.com