Minerals & Metals

1.Alloy Tool Steel Round Bar Alloy tool steel is a type of steel in which chromium, molybdenum, tungsten, vanadium and other alloying elements are added on the basis of carbon tool steel to improve hardenability, toughness, wear resistance and heat resistance. It is mainly used in the manufacture of measuring tools, cutting tools, impact- resistant tools, cold and hot molds and some special-purpose tools. Steel with alloying elements such as Si, Mn, Ni, Cr, W, Mo, and V added to carbon tool steel. The addition of Cr and Mn can improve the hardenability of tool steel, and other elements can be added selectively or at the same time according to requirements (the total amount of addition generally does not exceed 5%), that is, a series of alloy tool steels are formed. 2.Category of use The hardenability, hardenability, wear resistance and toughness of gold tool steel are higher than those of carbon tool steel, and can be roughly divided into three categories: steel for cutting tools, molds and measuring tools. Among them, steels with high carbon content (carbon mass fraction greater than 0.80%) are mostly used to manufacture cutting tools, measuring tools and cold work dies. The hardness of such steels after quenching is above HRC60 and has sufficient wear resistance; steels with moderate carbon content ( Carbon content of 0.35%~0.70%) is mostly used in the manufacture of hot work molds. The hardness of this type of steel after quenching is slightly lower, which is HRC50~55, but the toughness is good. The cutting tool produces strong wear and heat under working conditions, as well as vibration and a certain impact load. Steel for cutting tools should have high hardness, wear resistance, red hardness and good toughness. In order to ensure its high hardness and meet the needs of forming alloy carbides, the carbon content in steel is generally 0.80% to 1.45%. Chromium is the main alloying element of this type of steel, and its mass fraction is generally 0.50% to 1.70%. Some steels also contain tungsten to improve the performance of cutting metals. This type of tool steel contains alloying elements, so the hardenability is better than that of carbon tool steel, the deformation caused by heat treatment is small, and it has high hardness and wear resistance. Commonly used steels are chromium steel, silicon-chromium steel and chromium- tungsten-manganese steel. [Applications]: Mainly used to manufacture low-speed cutting tools (such as woodworking tools, fitter tools, drills, milling cutters, broaches, etc.) and measuring tools (such as calipers, micrometers, block gauges, templates, etc.). Measuring tool steel is required to have high hardness (62-65HRC), high wear resistance, sufficient strength and toughness, and high hot hardness (that is, the cutting tool can still maintain high hardness at high temperature); in order to ensure the accuracy of measurement, measuring tools are required. Cutting tool steel has good dimensional stability. [Chemical composition]: Measuring tool steel has high carbon content, wC=0.8%～ 1.50%, to ensure high hardness and wear resistance. The added alloying elements are Cr, Si, Mn, W, etc., to improve the hardenability, tempering resistance, hot hardness and wear resistance of steel. [Commonly used cutting tool steel]: 9SiCr is a widely used cutting tool steel, which is used to make various thin-edged low-speed cutting tools that require small deformation, such as die, tap, reamer, etc. [Commonly used measuring tool steel]: High-precision measuring tools (such as block gauges) can be made of measuring tool steel such as Cr2, CrWMn, etc., or bearing steel (such as GCr15); simple measuring tools (such as calipers, templates, rulers, gauges, etc.) are multi-purpose Carbon tool steel (such as T10A); for measuring tools that require precision and must prevent corrosion, stainless steel 3Cr13 and 9Cr18 are used. [Heat treatment]: The pre-heat treatment of measuring and cutting tool steel is spheroidizing annealing, and the final heat treatment is quenching and low- temperature tempering. After heat treatment, the hardness reaches 60-65HRC. High precision gauges can be cold treated after quenching to reduce the amount of retained austenite and thus increase their dimensional stability. In order to further improve dimensional stability, aging treatment can also be carried out after quenching and tempering. songshunmoldsteel41404340

Minimum Order: 1 bags

4140 Steel Product Information Steel Grade: 4140 Alloy steel Standard: AISI/ASTM/DIN/NF/JIS/GB/BS Place of Origin:Guangdong, China Brand Name:Songshun Model Number:4140/1.7225/42CrMo Technique:Hot Rolled Application:Die Steel Bar Special Use:Mold Steel Tolerance:±10% Shape:Round bars/Flat bar/Plate Delivery Time:8-14 days Heat treatment:Annealing/Q+T Processing Service:Bending, Welding, Decoiling, Cutting, Punching Technology:Hot Rolled/Forged/Clod Drawn Surface treatment:Black/Peeling/Polishing/Machined Deli , very condition:Hot rolled or forged/ Peeled or black surface/annealed or QT Test:UT100%/Elements testing Certificate:ISO/Mill certificate Service:Sample free and 24 hours online Experience:Ten years manufacturer experience Company Strength After more than ten years of development and growth, Songshun Iron and Steel has become a comprehensive special steel production enterprise, inventory enterprise and export enterprise. With an experienced export team and professional technical knowledge, Songshun Steel provides customers with technical advice and support, as well as global professional steel solutions and services. With satisfactory and reliable quality and professional services, the company's markets are all over the world, such as Colombia, Chile, Spain, Turkey, Iran, Vietnam, Malaysia, United Arab Emirates, Canada, Brazil, Mexico, etc. Welcome To Get a Quote MiKi Zhuo E-mail:jacklu@songshunsteel.com Skype/W , hatsapp/Wechat:+86-18269260283 ADD:No.4 Dongda Street, Shatou, Changan Town, Dongguan City, Guangdong Province, P.R.C China For more 4140 steel product information, please click this link: https://steelpurchase.com/4140-scm440-172 , 25-steel/ Company website: https://steelpurchase.com/ http://w , ww.songshunsteel.com/ songshunmoldsteel41404340

Minimum Order: 1 bags

Dongguan Songshun Mould Steel Co., Ltd. Dongguan Songshun Mould Steel Co., Ltd. is an Indusrtial and trading company with 2 warehouses that manufactures good & high quality kinds of steels starting from 2012. The company provides the customized products and OEM service. What´s more, we keep the mass stock of over 20000 tons. In those years, we offer a wide range of steels to our customers from all over the world. And we enjoy high praise among them. SAE 4340 steel Product Details  ·GB steel number:CN:40CrNiMoA DIN:36CrNiMo4 JIS:SNCM439 BS:816M40  US:AISI/ASTM4340 ·keyword:SAE Alloy 4340 Steel Bar ·Usage: It is used as important quenched and tempered parts that require good toughness,high strength and large size, such as heavy machinery and high-load shafts,turbine shafts with a diameter greater than 250mm, helicopter rotor shafts, turbojet engine turbine shafts,blades, high Loaded transmission parts, crankshaft fasteners. gears, etc.; ·Other Steel Types:5140 /4140 / 4340 / 4142 / 15CrMo / 6150 / 38CrMoAI / 8620 ..... ·Serve:OEM/ODM ·Delivery status:With heat treatment (normalized, annealed or high temperature tempered) or without heat treatment Goods, the delivery status should be specified in the contract ·AISI/ASTM 4340 Chemical Composition C:0.37-0.44  Si:0.17-0.37  S:≤0.035  P:≤0.035 Mn:0.50-0.80 Cr:0.60-0.90 Mo:0.15-0.25 N:1.25-1.65 ·ASTM 4340 Mechanical Properties Tensile strength σb (MPa): ≥980(100) Yield strength σs (MPa): ≥835(85) Elongation δ5 (%): ≥12 Area shrinkage ψ (%): ≥55 Impact energy Akv (J): ≥78 Elongation δ5 (%): ≥12 Area shrinkage ψ (%): ≥55 Impact energy Akv (J): ≥78 Impact toughness value αkv (J/cm2): ≥98(10) Sample size: sample blank size is 25mm ·Surface Treatment Plate: Origin Black,Orign cold rolled bright, Machined,Grinded Bar:Origin Black, Orign cold rolled(drawn) bright,Turned, Peeled, Grinded ·For more 4340 steel product information, please click this link: https://steelpurchase.com/4340-sncm439-16 , 563-steel/# songshunmoldsteel41404340

Minimum Order: 2 barrels

1.Product name JIS SCM440 Steel Mechanical Properties Alloy Structual Steel 2.keyword   SCM440 Steel Mechanical Properties   3.Standard AISI/ASTM/DIN/NF/JIS/GB/BS 4.Steel Grade AISI 4140/ASTM 4140/DIN 1.7225 /NF 40CD4 /JIS SCM440 /GB 42CrMo /BS 708M40 5.Chemical Compositions(%) C: 0.38-0.45   Si: 0.17-0.37  Mn: 0.50 , -0.80  P≤0.035  S ≤0.035   Cr: 0.90-1.20  Mo: 0.15-0.25 6.Mechanical properties Tensile strength σb (MPa): ≥1080(110) Yield strength σs (MPa): ≥930(95) Elongation δ5 (%): ≥12 Area shrinkage ψ (%): ≥45 Impact energy Akv (J): ≥63 Impact toughness value αkv (J/cm2): ≥78(8) Hardness: ≤217HB Sample size: sample blank size is 25mm 7.Surface treatment Black/Peeling/Polishing/Machined 8.Techniqu , e Cold/Hot rolled, Cold-Drawn or Hot Forged 9.Heat Treatment Annealed; Quenched; Tempered 10.Delivery Condition Hot Rolled or Forged/Peeled or Black Surface/Annealed or QT Heat treatment standard Quenching at 850℃, oil cooling; tempering at 560℃, water cooling, oil cooling 10.Feature This steel has good strength, good toughness, high hardenability, good workability, small processing deformation, quite good fatigue resistance, small deformation during quenching, high creep strength and durable strength at high temperature and so on. 11.Test SGS/UT100%/Elements Testing 12.Certificate SGS/ISO/Mill Certificate 13.Delivery status Delivered in heat-treated (normalized, annealed or high temperature tempered) or unheated state 14.E-mail jacklu@songshunsteel.com 15.Skype/Whatsapp/ , Wechat +86-18269260283 16.Company website https://steelpurchase.com/ http://www.songs , hunsteel.com/ 17.songshunmoldsteel41404340

Minimum Order: 1 bags

Flat steel refers to steel with a width of 12-300mm, a thickness of 3-60mm, a rectangular cross-section and a slight blunt edge. Flat steel can be finished steel, and can also be used as blanks for welded pipes and thin slabs for stacked sheets. Main application: Flat steel can be used as a finished material to make hoop iron, tools and mechanical parts, and it can be used as a house frame structure and escalator in construction. advantage The flat steel is rolled with negative deviation, but is delivered according to the actual weight, and the utilization rate is 1 to 5 percentage points higher than that of the steel plate. Flat steel can be produced with fixed thickness, fixed width and fixed length according to user needs, which reduces cutting for users, saves processes, reduces labor and material consumption, and also reduces processing loss of raw materials, saving time, labor, and saving. material. Products have been professionally used in steel structure manufacturing, machinery manufacturing, automobile industry, mining machinery, hoisting machinery and other industrial materials. Profile steel is one of the four major varieties of steel (plate, tube, profile, wire). According to the section shape, the section steel is divided into simple section section steel and complex section section steel (section steel). The former refers to square steel, round steel, flat steel, angle steel, hexagonal steel, etc.; the latter refers to I-beam, channel steel, rail, window frame steel, curved steel, etc. Square steel - steel with square section, hot-rolled and cold-rolled; hot- rolled square steel has a side length of 5-250mm; cold-drawn square steel has a side length of 3-100mm. Round bar - steel with round section, divided into three types: hot-rolled, forged and cold-drawn. The diameter of hot-rolled round bar is 5-250mm, of which 5-9mm is commonly used as the raw material for drawing steel wire, called wire rod; Disk supply is also called hot rolled wire rod. The forged round steel is straight and thick, and is used as a shaft blank. The diameter of cold-drawn round steel is 3-100 mm, and the dimensional accuracy is high. Angle steel - divided into two kinds of equal angle steel and unequal angle steel. The specification of angle steel is expressed by the dimensions of side length and side thickness. The specifications of angle steel usually produced are 2-20, that is, the number of centimeters on the side. For example, No. 5 equilateral angle steel refers to an angle steel with a side length of 5cm (50mm). The same horn often has 2-7 different side thicknesses. Calculation method of flat steel weight: Flat steel: weight per meter = 0.00785 * thickness * side width Please request a quote. Contact us: MiKi Zhuo E-mail:jacklu@songshunsteel.com Skype/W , hatsapp/Wechat:+86-18269260283 ADD:No.4 Dongda Street, Shatou, Changan Town, Dongguan City, Guangdong Province, P.R.C China For more steel products information, please click this link: https://steelpurchase.com/ http://www. , songshunsteel.com/ https://songshun.en.alibaba. , com/ songshunmoldsteel41404340

Minimum Order: 1 bags

Heat Treatment 4140 Alloy Steel Equivalent Steel Grade  China GB steel number 42CrMo, Germany DIN steel number 42CrMo4, Germany DIN material number 1.7225, French NF standard 40CD4/42CD4, Japanese JIS standard SCM440, British BS standard 708M40/708A42/709M40, American AISI/ASTM 4140, American SAE 4140, American UNS Standard G41400 Heat Treatment 4140 Alloy Steel Chemical Composition C:0.38-0.45 Si:0.17-0.37 S：≤0.035 P:≤0.035 Mn:0.50-0.80 Cr:0.90-1.20 Mo:0.15-0.25 Ni:≤0.30 Cu≤0.30 SAE 4140 Mechanical Properties Tensile Strength σb (MPa):≥1080(110) Yield Strength σS (MPa):≥930(95) Elongation δ5 (%):≥12 Reduction ψ (%):≥45  Impact Energy Akv (J):≥63 Impact Toughness akv (J/cm2):≥78(8) Annealed Hardness ≤217HB Our advantage Focus on the steel industry for more than ten years Strength factory Professional service Quality assurance Customized according to customer requirements Factory price Fast shipping time Good after-sales service Happy to work with customers High repurchase rate, etc. songshunmoldsteel41404340

Minimum Order: 1 bags

Introduction of 4140 4140 steel has high strength, hardenability, good toughness, small deformation during quenching, and high creep strength and durable strength at high temperature. It is used to manufacture forgings requiring higher strength and larger quenched cross section than 35CrMo steel, such as large locomotive traction gear, supercharger transmission gear, rear axle, highly loaded connecting rod and spring clip, and can also be used for oil drilling. Heat treatment: 1. Normalizing: Heat the furnace to 900°C~930°C, keep the thickest cross section per inch at this temperature for one hour, and cool in air. 2. Heat to austenitizing at a temperature of 860℃~885℃, and keep the thickest cross section per inch for one hour at this temperature 3. Normalizing or oil quenching, and cooling to a maximum temperature of 121°C 4. Temper at a temperature that achieves the following mechanical properties. The thickest cross-section per inch is held for one hour at the tempering temperature, and the tempering temperature range is 640 ° C ~ 680 ° C 5. For each heat treatment process, a heat treatment chart must be drawn. 6. The mechanical property test shall be carried out in accordance with the stipulations of ASTM. A-370. The sample material used for the test shall be cut from the test bar of the same furnace steel. The casting or forging represented by the sample and the test bar shall be in the same furnace. The test bar shall be heat treated in the same furnace together with the charge. 7. The mechanical properties should meet the following requirements: (Tested with a test bar, sampling according to APT 6A, 110K standard) - Tensile strength minimum lb/inch (862) Yield strength minimum lb/inch 110.000 (758) 2 inches The minimum value of elongation is 15% and the minimum value of section shrinkage rate is %40. Brinell hardness HB285 ~ take, the casting or forging represented by the sample and the test bar must be in the same furnace, and the test bar should be heat treated in the same furnace together with the charge. 8. The mechanical properties should meet the following requirements: (tested with test bars, sampling according to APT 6A, 110K standard) - minimum tensile strength lbs/inch (862) minimum yield strength lbs/inch (758) 2 inches Minimum elongation %15 Minimum shrinkage of section %40 Brinell hardness HB285～352 9. Marking: Each part shall be printed with heat treatment marks and hardness with low stress steel stamp. Company strength   Dongguan Songshun Mould Steel Co., Ltd. is an Indusrtial and trading company with 2 warehouses that manufactures good & high quality kinds of steels starting from 2012. The company provides the customized products and OEM service. What´s more, we keep the mass stock of over 20000 tons. In those years, we offer a wide range of steels to our customers from all over the world. And we enjoy high praise among them. Don't hesitate, here is your best choice! contact us,Latest business news for you!welcome your inquiry and order! songshunmoldsteel41404340

Minimum Order: 4 cubic metres

1.What is cold rolled steel? Cold rolled steel is steel produced by cold rolling. Cold rolling is a steel sheet obtained by further thinning the No. 1 steel sheet to a target thickness under room temperature conditions. Compared with hot-rolled steel sheet, cold- rolled steel sheet has more accurate thickness, smooth and beautiful surface, and also has various superior mechanical properties, especially in terms of processability. Because cold-rolled raw coils are relatively brittle and hard, and are not suitable for processing, cold-rolled steel sheets are usually required to be annealed, pickled and surface smoothed before being delivered to customers. The maximum thickness of cold rolling is below 0.1--8.0MM, for example, the thickness of cold rolled steel plate in most factories is below 4.5MM; the minimum thickness and width are determined according to the equipment capacity and market demand of each factory. 2.How is cold rolled steel processed? Using hot-rolled steel coil as raw material, after pickling to remove oxide scale, cold continuous rolling is carried out, and the finished product is rolled hard coil. The cold work hardening caused by continuous cold deformation increases the strength, hardness and toughness and plastic index of rolled hard coil. , so the stamping performance will deteriorate and can only be used for parts with simple deformation. Hard-rolled coils can be used as raw material for hot-dip galvanizing plants, because hot-dip galvanizing lines are equipped with annealing lines. The weight of the rolled hard coil is generally 6~13.5 tons, and the hot-rolled pickled coil is continuously rolled at normal temperature. The inner diameter is 610mm. 3.What are the relevant standards for cold rolled steel? GB905: Cold rolled round steel, square steel, hexagonal steel GB708: Cold rolled steel sheet and strip (1)Grade DC01、 DC02、 DC03、DC04、SPCC、SPCD、SPCE (2)Supply Standard GB/T 708,EN 10130:1998,JISG3141:2005 (3)Product Size (mm) Nominal thickness:0.3～3.0 Nominal width:20～1600 (4)Use Parts suitable for deep drawing of general forming knives songshunmoldsteel41404340

Minimum Order: 1 bags

Songshun Alloy Steel Round Bar We are an industry and trade company with various steel products and have many years of experience in this field. We offer a wide variety of steels with competitive prices and good quality, and maintain a large inventory of over 20,000 tons. Our main products are alloy steel, tool steel, stainless steel, spring steel, bearing steel and other round and flat steel. Over the years, we have provided a wide range of high-quality steel for the automobile manufacturing, engineering machinery, mold and tool manufacturing industries, and have also been highly praised by domestic and foreign customers.songshunmoldsteel41404340

Minimum Order: 2 barrels

In addition to iron and carbon, alloy steel is called alloy steel by adding other alloying elements. An iron-carbon alloy formed by adding an appropriate amount of one or more alloying elements on the basis of ordinary carbon steel. According to the difference of added elements and appropriate processing technology, special properties such as high strength, high toughness, wear resistance, corrosion resistance, low temperature resistance, high temperature resistance, and non-magnetic properties can be obtained. In addition to iron, carbon and unavoidable small amounts of silicon, manganese, phosphorus and sulfur, steel also contains a certain amount of alloying elements. The alloying elements in steel include one or more of silicon, manganese, molybdenum, nickel, antimony, vanadium, titanium, niobium, boron, lead and rare earth. This steel is called alloy steel of the alloy steel system. According to their respective resource conditions, it is found in my country that the alloy steel system mainly composed of silicon, manganese, vanadium, titanium, niobium, boron, lead and rare earth accounts for more than 10% of the total steel output. 8 categories. They are: alloy structural steel, spring steel, bearing steel, alloy tool steel, high speed tool steel, stainless steel, heat resistant stainless steel and electrical silicon steel.songshunmoldsteel41404340

Minimum Order: 2 barrels

1.The main alloying elements of alloy steel are silicon, manganese, chromium, nickel, molybdenum, tungsten, vanadium, titanium, niobium, zirconium, cobalt, aluminum, copper, boron and rare earth. Among them, vanadium, titanium, niobium, zirconium, etc. It is a strong carbide forming element in steel. Given enough carbon, they can form their own carbides under the right conditions. When carbon is lacking or under high temperature conditions, they enter into solid solution in atomic state; manganese, chromium, tungsten, and molybdenum are carbide-forming elements, part of which enters solid solution in atomic state, and the other part forms substitute alloy cementite; aluminum, copper, nickel , cobalt, silicon, etc. are elements that do not form carbides and usually exist in solid solution in an atomic state. 2.There are many types of alloy steel, usually divided into low alloy steel (content <5%), medium alloy steel (content 5% ~ 10%) and high alloy steel (content > 10%). According to quality, it is divided into high-quality alloy steel and special alloy steel; according to its characteristics and uses, it is divided into alloy structural steel, stainless steel, acid-resistant steel, wear-resistant steel, heat-resistant steel, alloy tool steel, rolling bearing steel, alloy spring steel and special properties. Steel (such as soft magnetic steel, permanent magnetic steel and non-magnetic steel). 3.Alloy steel contains more other elements than carbon steel Alloy steel refers to steel containing silicon and manganese as alloying elements or deoxidizing elements, as well as other alloying elements, and some also contain certain non-metallic elements. According to the content of alloying elements in steel, it can be divided into low alloy steel, medium alloy steel and high alloy steel. The carbon steel mainly refers to the steel whose mechanical properties depend on the carbon content in the steel, and generally does not add a large amount of alloying elements, and is sometimes called ordinary carbon steel or carbon steel. Carbon steel is also called carbon steel, an iron-carbon alloy with a carbon content of less than 2% WC. In addition to carbon, carbon steel generally contains a small amount of silicon, manganese, sulfur, and phosphorus. According to the purpose, carbon steel can be divided into three categories: carbon structural steel, carbon tool steel and free-cutting structural steel. According to the carbon content, carbon steel can be divided into low carbon steel (WC ≤ 0.25%), medium carbon steel (WC0.25% - 0.6%) and high carbon steel (WC>0.6%)songshunmoldsteel41404340

Minimum Order: 1 bags

1.Forging DIN 1.7225 Steel Product 4140 steel is a kind of alloy structural steel. It belongs to the steel with the American grade equivalent to the 42CrMo grade in my country. This kind of steel belongs to the medium hardenability steel with high yield, good comprehensive mechanical properties, good strength, good toughness and hardenability. High advantages, its carbon content is 0.33%-0.48%, its tensile strength is 795 MPa, and its hardness is 241HB. After heat treatment at 4140, it has good strength and good comprehensive mechanical properties, and it has good manufacturability. Fasteners, salvage tools,etc. 2.Forging DIN 1.7225 Steel Corresponding Steel Number: China GB steel number 42CrMo, Germany DIN steel number 42CrMo4, Germany DIN material number 1.7225, French NF standard 40CD4/42CD4, Japanese JIS standard SCM440, British BS standard 708M40/708A42/709M40, American AISI/ASTM 4140, American SAE 4140, American UNS Standard G41400 (4140 alloy structural steel, executive standard: ASTM A29/A29M-04) 3.Forging DIN 1.7225 Steel Application: It is used to manufacture forgings that require higher strength and larger quenched and tempered section than 35CrMo steel, such as large gears for locomotive traction, supercharger transmission gears, rear axles, connecting rods and spring clips that are heavily loaded, and can also be used for Drill pipe joints and fishing tools for oil wells below 2000m, and can be used for molds of bending machines,etc. We provide high-quality steel, ex-factory price, support customization, strong company and factory strength; welcome your inquiry and order;please contact us for quotes.​songshunmoldsteel41404340

Minimum Order: 3 bushels

AISI 4340 steel is a medium carbon, low alloy steel known for its toughness and strength in relatively large sections. AISI 4340 is also one kind of nickel chromium molybdenum steels. 4340 alloy steel is generally supplied hardened and tempered in the tensile range of 930 – 1080 Mpa. Pre hardened and tempered 4340 steels can be further surface hardened by flame or induction hardening and by nitriding. The 4340 steel has good shock and impact resistance as well as wear and abrasion resistance in the hardened condition. AISI 4340 steel properties offer good ductility in the annealed condition, allowing it to be bent or formed. Fusion and resistance welding is also possible with our 4340 alloy steel. ASTM 4340 material is often utilized where other alloy steels do not have the hardenability to give the strength required. For highly stressed parts it is excellent choice. AISI 4340 alloy steel can also be machined by all customary methods.songshunmoldsteel41404340

Minimum Order: 2 barrels

Product name AISI/ASTM 4140 Steel Bars Hot Rolled AISI/ASTM 4140 Steel Bars Products keyword AISI/ASTM 4140 Steel Bars Standard AISI/ASTM/DIN/NF/JIS/GB/BS Steel Grade AISI 4140/ASTM 4140/DIN 1.7225 /NF 40CD4 /JIS SCM440 /GB 42CrMo /BS 708M40 Chemical Compositions(%) C:0.38-0.45   Si:0.17-0.37  Mn:0.50-0.80

Minimum Order: 1 bags