Steel Wire Mesh

Flattened Expanded AISI304 and AISI316 Stainless Steel Stretched Sheet Decorative Mesh Expanded Stainless Steel Mesh has many advantages over expanded steel as it offers much better corrosion resistance and longer service life. SS expanded sheet and foils are widely used as battery netting, filtration sheet and decorative mesh uses. SS304 and 316 Expanded Meshes are new decorative mesh favored in modern architectural design. SS 304 and 316 Series Expanded Plates are supplied with a variety of openings: 1, Standard Rhombic Shaped / Diamond Shaped 2, Heavy Type (Tortoise-shaped) 3, Flattended Type 4, Micron / Micro Opening 5, Special Types SWD: 2.5mm-50mm Short Way of the Diamond, the distance from the middle of the bond on one side to the middle of the bond on the opposite side. LWD: 3mm-100mm(Long Way of the Diamond) is the distance across the largest dimension of the diamond measured halfway between the diamonds. Width: 0.5m-2.7m, Length:1m-3.6m. Thickness(gauge): Up to 8mm, Original thickness of metal before expanding. Strand Width: 0.3mm to 8mm, Amount of metal between diamonds to produce one strand. SWD, LWD Direction: Parallel to Length or Parallel to Width Stainless Steel Type 304 Flattened Expanded Metal SS304 Expanded Flattened Diamond Shaped Metal

PRODUCTS DESCRIPTION Components: The HIGH TENSILE ROCKFALL MESH system consists of four main components that are carefully coordinated with each other: 1.HIGH TENSILE ROCKFALL NET   It is made of high-tensile steel wire with an ultimate tensile strength of 1770 N/mm2. Detailed Product Description: 1.wire diameter:3mm 2.high tensile strength 1770Mpa 3.mesh size:80mm x 140mm 4.Mesh shape:diamond 5.Material:high tensile steel wire 6.Corrosion protection:super coating 7.Coating:150g/m2 8.Breaking load of single wire:12.5KN 9.Tensile strength:110KN/m HIGH TENSILE ROCKFALL MESH mesh standard roll: Mesh edges knotted Roll width:2.3m-3.5m Roll length:110m-30m Weight:1.75kg/m2 2.SOIL OR ROCK NAILS Adapted to the local soil and rock static requirements, the HIGH TENSILE ROCKFALL MESH can be anchored in accordance with our dimensioning concept with commercial soil or rock nails.The main anchors of the system are installed in a grid typically from 6.6 to 16.4 ft (2.0 to 5.0m)horizontal and vertical spacing.Actual spacing depends upon the results of site analysis and modeling. Anchor consist of commercially available steel bars ranging from 1.0 to 1.25 ft (25 to 32mm). Selfdrilling grout injection anchors are also permitted.Additional anchors may also be used to provide added support at boundaries and in low points and hollows. 3.SPIKE PLATES Rigid spike plates that are reinforced with ribbing ensure optimal load transmission from soil or rock anchors to the HIGH TENSILE ROCKFALL MESH. These plates are placed over the anchor heads and tightened to pre-tension the mesh onto the slope. The plates are galvanized and have dimensions of 13.0''*7.5"*0.4"(330mm*190mm , *10mm). 4.CONNECTION CLIPS The connection clips high-strength steel wire connection clips enable mesh sections to be joined without overlapping and still guarantee one hundred percent transfer of forces. These claw are hot dip galvanized and consist of 0.25"(6mm) thick steel spiral. 5.SOIL OR ROCK NAILS Adapted to the local soil and rock static requirements, the HIGH TENSILE ROCKFALL MESH can be anchored in accordance with our dimensioning concept with commercial soil or rock nails.The main anchors of the system are installed in a grid typically from 6.6 to 16.4 ft (2.0 to 5.0m)horizontal and vertical spacing.Actual spacing depends upon the results of site analysis and modeling. Anchor consist of commercially available steel bars ranging from 1.0 to 1.25 ft (25 to 32mm). Selfdrilling grout injection anchors are also permitted.Additional anchors may also be used to provide added support at boundaries and in low points and hollows. Sure,if you want to know more aboue mesh,you can click here to know.

Minimum Order: 20 square metres