Telecommunications & Networks

UPCOM IES405-F is a rugged industrial grade, Din-Rail, layer2, Unmanaged Ethernet switch that supports 4-port 10/100M Base-T(X) +1-port 100Base-FX. Plug and play, easy to install, no configuration is required, can be operated at wide temperatures range from -40 to 75°C. IES405-F adopts standard Industrial design, IP40 protection, aluminum alloy shell, support Din-rail or wall installation, fanless design, support EMC level 4 protection, Single power DC12-48V or single AC/DC220V optional, can meet the requirement of various Industrial automation, Data Center Network, Intelligent Transportation System, Electric Power Industry, and new energy applications. Support 4-port 10/100M Base-T(X) + 1-port 100Base-FX; Plug-and-play, no configuration is required; Support indicator status display; Support IP40 protection, aluminum alloy shell, fanless design; Support Broadcast storm suppression; Support Single DC12-48V or single AC/DC 220V power supply; Power supply input support anti-reverse protection and non-polarity; Support over Voltage, over current, EMC protection; Support -40~75°C wide operating temperature range; DIN-Rail or wall Installation; Warranty:5years

Minimum Order: 1 bags

Product Description 1.25Gb/s GLC-T 10/100/1000M Copper Ethernet SFP Transceiver 100m Description GLC-T10/100/1000 copper SFP transceiver is high performance, cost effective module compliant with the Gigabit Ethernet and 10/100/1000BASE-T standards as specified in IEEE 802. 3-2002 and IEEE 802.3ab, which supporting 10/100/1000Mbps data- rate up to 100 meters reach over unshielded twisted-pair category 5 cable. The GLC- T10/100/1000 supports 10/100/1000 Mbps full duplex data-links with 5-level Pulse Amplitude Modulation (PAM) signals. All four pairs in the cable are used with symbol rate at 250Mbps on each pair. The GLC-T10/100/1000 provides standard serial ID information compliant with SFP MSA, which can be accessed with address of A0h via the 2-wire serial CMOS EEPROM protocol. The physical IC can also be accessed via 2-wire serial bus at address ACh. Features Up to 1.25Gb/s bi-directional data links Hot-pluggable SFP footprint Extended case temperature range (-40°C to +85°C ) Fully metallic enclosure for low EMI Low power dissipation Compact RJ-45 connector assembly Detailed product information in EEPROM +3.3V single power supply Access to physical layer IC via 2-wire serial bus 10/100/1000 BASE-T operation in host systems with SGMII interface Compliant with SFP MSA Compliant with IEEE Std 802.3TM-2002 Compliant with FCC 47 CFR Part 15, Class B RoHS Compliant Products Applications 1.25 Gigabit Ethernet over Cat 5 cable Switch/Router to Switch/Router Link High speed I/O for file severs Optical Parameters Parameter Symbol Min. Typical Max. Units Notes/Conditions Supply Current Is 320 375 mA 1.2W max power over full range of voltage and temperature. See caution note below Input Voltage Vcc 3.13 3.3 3.47 V Referenced to GND Surge Current Isurge 30 mA Hot plug above steady state current. See caution note Parameter Symbol Min. Max. Units Notes/Conditions SFP Output LOW VOL 0 0.5 V 4.7k to 10k pull-up to host_Vcc. SFP Output HIGH VOH host_Vcc -0.5 host_Vcc + 0.3 V 4.7k to 10k pull-up to host_Vcc. SFP Input LOW VIL 0 0.8 V 4.7k to 10k pull-up to Vcc. SFP Input HIGH 2 Vcc + 0.3 V V 4.7k to 10k pull-up to Vcc. Transmission Line-SFP Parameter Symbol Min. Typical Max. Units Notes/Conditions Line Frequency fL 125 MHz 5-level encoding, per IEEE 802.3 Tx Output Impedance Zout,TX 100 Ohm Differential Rx Input Impedance Zin,RX 100 Ohm Differential

Product Description 12F Fiber Optic MTP / MPO - 12 x LC Breakout Cable OM3 OM4 LSZH / PVC The MPO connector offers up to 12 times the density of standard connectors, providing significant space and cost savings. MPO connectors utilize precision molded MT ferrules, with metal guide pins and precise housing dimensions to ensure fiber alignment when mating. The MPO can be mass terminated in combinations of 4, 8, or 12 fiber ribbon cables. The MPO Adapter comes standard in black. Fiber Optic MTP / MPO - LC Breakout Cable - Features: Precision molded MT ferrule High precision guide pins for exact alignment Compact design, up to 4,8,12,24 fibers IEC 61754-7 Compliant EIA/TIA-604-5 Compliant Fiber Optic MTP / MPO - LC Breakout Cable - Applications: Telecommunication Networks Asynchronous Transmission Mode(ATM) Gigabit Ethernet Active Deviced/Transceiver Interface CATV, Video and Multimedia Premise Installations Telecommunication Networks Parallel optical interconnect between PC Cards and patch panels Interconnection for O/E modules Industrial & Military Optical Switch interframe connections Fiber Optic MTP / MPO - LC Breakout Cable - Specifications: Item LC,SC,ST,FC....... MPO/MTP End face type PC,UPC and APC PC and APC Fiber type SM(G652,G655,G657)；MM(OM1-OM5) Core number 12,24 Cable Diameter 0.9,2.0,3.0 Mini Round cable:Max4.5mm； Ribbon cable:Max3.0*5.0mm Insertion loss(dB) ≤ 0.3 Standard:≤0.35/0.7(Typical/Max) Low Loss:≤0.2/0.35(Typical/Max) Return loss(Min) UPC SM:40dB APC SM:60 dB PC MM:25 dB SM: APC:60dB MM: PC:20dB Test Wavelength (nm) SM:1310/1550 , MM:850/1300 Repeatability ≤ 0.1dB Durability ≤ 0.2dB Interchangeability ≤ 0.2dB Operating Temperature -20