Machine Tools Parts

Products Description 37GB 12volt 12v 24v 2500rpm 20 Watt 30w High Speed 20kg Cm 1.5nm Dc Gear Motors For Curtains 2D drawing 37GB 12volt 12v 24v 2500rpm 20 Watt 30w High Speed 20kg Cm 1.5nm Dc Gear Motors For Curtains 0 Picture 37GB 12volt 12v 24v 2500rpm 20 Watt 30w High Speed 20kg Cm 1.5nm Dc Gear Motors For Curtains 1 Specifications DC Motor Technical Data Model Rated Voltage(V) No-Load Parameters Rated Parameters Stall Parameters Speed Current Speed Current Torque Output eff Torque Current rpm mA rpm A mN.m W % mN.m A ZY3879 12 4500 350 3600 1.23 24.50 9.24 62.83 73.50 7.00 ZY3879 12 5000 400 4000 1.35 24.50 10.26 63.34 73.50 7.50 ZY3879 12 8000 900 6400 2.65 29.70 19.90 62.59 89.10 13.00 ZY3879 24 3500 100 2800 0.48 24.90 7.30 63.37 74.70 3.30 DC Motor With Gearbox Technical Data (0.5M) Gearbox parameters 12V-4500RPM Input 12V-5000RPM Input Length (mm) Transmission Efficiency (%) Gear Ratio Rated Output Speed (RPM) Rated Output Power (W) Rated Torque (mN.m) Maximum Instantaneous Torque (mN.m) Rated Output Speed (RPM) Rated Output Power (W) Rated Torque (mN.m) Maximum Instantaneous Torque (mN.m) 22.5 81 6.5 553.8 7.48 128.99 386.98 615.4 8.31 128.99 386.98 22.5 73 9.3 387.1 6.74 166.33 498.99 430.1 7.49 166.33 498.99 22.5 73 11.8 305.1 6.74 211.04 633.13 339.0 7.49 211.04 633.13 22.5 73 14.2 253.5 6.74 253.97 761.90 281.7 7.49 253.97 761.90 22.5 73 17.4 206.9 6.74 311.20 933.60 229.9 7.49 311.20 933.60 24.5 65.6 21.8 165.1 6.06 350.37 1051.11 183.5 6.73 350.37 1051.11 24.5 65.6 27.5 130.9 6.06 441.98 1325.94 145.5 6.73 441.98 1325.94 24.5 65.6 36.6 98.4 6.06 588.24 1764.71 109.3 6.73 588.24 1764.71 24.5 65.6 40.4 89.1 6.06 649.31 1947.93 99.0 6.73 649.31 1947.93 26.5 59 58.1 62.0 5.45 839.84 2500.00 68.8 6.05 839.84 2500.00 26.5 59 73.4 49.0 5.45 1061.00 2500.00 54.5 6.05 1061.00 2500.00 26.5 59 83 43.4 5.45 1199.77 2500.00 48.2 6.05 1199.77 2500.00 26.5 59 89 40.4 5.45 1286.50 2500.00 44.9 6.05 1286.50 2500.00 26.5 59 95 37.9 5.45 1373.23 2500.00 42.1 6.05 1373.23 2500.00 26.5 59 103 35.0 5.45 1488.87 2500.00 38.8 6.05 1488.87 2500.00 29.5 53 119 30.3 4.89 1545.22 2500.00 33.6 5.44 1545.22 2500.00 29.5 53 136 26.5 4.89 1765.96 2500.00 29.4 5.44 1765.96 2500.00 29.5 53 171 21.1 4.89 2220.44 2500.00 23.4 5.44 2220.44 2500.00 29.5 53 194 18.6 4.89 2500.00 2500.00 20.6 5.44 2500.00 2500.00 29.5 53 207 17.4 4.89 2500.00 2500.00 19.3 5.44 2500.00 2500.00 29.5 53 221 16.3 4.89 2500.00 2500.00 18.1 5.44 2500.00 2500.00 29.5 53 242 14.9 4.89 2500.00 2500.00 16.5 5.44 2500.00 2500.00 29.5 53 277 13.0 4.89 2500.00 2500.00 14.4 5.44 2500.00 2500.00 29.5 53 305 11.8 4.89 2500.00 2500.00 13.1 5.44 2500.00 2500.00 32.5 47.8 350 10.3 4.41 2500.00 2500.00 11.4 4.91 2500.00 2500.00 32.5 47.8 422 8.5 4.41 2500.00 2500.00 9.5 4.91 2500.00 2500.00 32.5 47.8 465 7.7 4.41 2500.00 2500.00 8.6 4.91 2500.00 2500.00 32.5 47.8 513 7.0 4.41 2500.00 2500.00 7.8 4.91 2500.00 2500.00 32.5 47.8 532 6.8 4.41 2500.00 2500.00 7.5 4.91 2500.00 2500.00 32.5 47.8 586 6.1 4.41 2500.00 2500.00 6.8 4.91 2500.00 2500.00 32.5 47.8 712 5.1 4.41 2500.00 2500.00 5.6 4.91 2500.00 2500.00 32.5 47.8 784 4.6 4.41 2500.00 2500.00 5.1 4.91 2500.00 2500.00 DC Motor With Gearbox Technical Data (0.5M) Gearbox parameters 12V-8000RPM Input 24V-3500RPM Input Length (mm) Transmission Efficiency (%) Gear Ratio Rated Output Speed (RPM) Rated Output Power (W) Rated Torque (mN.m) Maximum Instantaneous Torque (mN.m) Rated Output Speed (RPM) Rated Output Power (W) Rated Torque (mN.m) Maximum Instantaneous Torque (mN.m) 22.5 81 6.5 984.6 16.12 156.37 469.11 430.8 5.91 131.10 393.30 22.5 73 9.3 688.2 14.53 201.63 604.90 301.1 5.33 169.05 507.14 22.5 73 11.8 542.4 14.53 255.84 767.51 237.3 5.33 214.49 643.47 22.5 73 14.2 450.7 14.53 307.87 923.61 197.2 5.33 258.11 774.34 22.5 73 17.4 367.8 14.53 377.25 1131.75 160.9 5.33 316.28 948.84 24.5 65.6 21.8 293.6 13.06 424.73 1274.20 128.4 4.79 356.09 1068.27 24.5 65.6 27.5 232.7 13.06 535.79 1607.36 101.8 4.79 449.20 1347.59 24.5 65.6 36.6 174.9 13.06 713.09 2139.26 76.5 4.79 597.84 1793.52 24.5 65.6 40.4 158.4 13.06 787.12 2361.36 69.3 4.79 659.91 1979.73 26.5 59 58.1 110.2 11.74 1018.09 2500.00 48.2 4.31 853.55 2500.00 26.5 59 73.4 87.2 11.74 1286.19 2500.00 38.1 4.31 1078.32 2500.00 26.5 59 83 77.1 11.74 1454.41 2500.00 33.7 4.31 1219.35 2500.00 26.5 59 89 71.9 11.74 1559.55 2500.00 31.5 4.31 1307.50 2500.00 26.5 59 95 67.4 11.74 1664.69 2500.00 29.5 4.31 1395.65 2500.00 26.5 59 103 62.1 11.74 1804.87 2500.00 27.2 4.31 1513.17 2500.00 29.5 53 119 53.8 10.55 1873.18 2500.00 23.5 3.87 1570.44 2500.00 29.5 53 136 47.1 10.55 2140.78 2500.00 20.6 3.87 1794.79 2500.00 29.5 53 171 37.4 10.55 2500.00 2500.00 16.4 3.87 2256.69 2500.00 29.5 53 194 33.0 10.55 2500.00 2500.00 14.4 3.87 2500.00 2500.00 29.5 53 207 30.9 10.55 2500.00 2500.00 13.5 3.87 2500.00 2500.00 29.5 53 221 29.0 10.55 2500.00 2500.00 12.7 3.87 2500.00 2500.00 29.5 53 242 26.4 10.55 2500.00 2500.00 11.6 3.87 2500.00 2500.00 29.5 53 277 23.1 10.55 2500.00 2500.00 10.1 3.87 2500.00 2500.00 29.5 53 305 21.0 10.55 2500.00 2500.00 9.2 3.87 2500.00 2500.00 32.5 47.8 350 18.3 9.51 2500.00 2500.00 8.0 3.49 2500.00 2500.00 32.5 47.8 422 15.2 9.51 2500.00 2500.00 6.6 3.49 2500.00 2500.00 32.5 47.8 465 13.8 9.51 2500.00 2500.00 6.0 3.49 2500.00 2500.00 32.5 47.8 513 12.5 9.51 2500.00 2500.00 5.5 3.49 2500.00 2500.00 32.5 47.8 532 12.0 9.51 2500.00 2500.00 5.3 3.49 2500.00 2500.00 32.5 47.8 586 10.9 9.51 2500.00 2500.00 4.8 3.49 2500.00 2500.00 32.5 47.8 712 9.0 9.51 2500.00 2500.00 3.9 3.49 2500.00 2500.00 32.5 47.8 784 8.2 9.51 2500.00 2500.00 3.6 3.49 2500.00 2500.00

Description The D series Multistage Ring Section Centrifugal Water Pump is a utility- grade, high-pressure, ring section pump with heavy duty, segmental ring, diffuser design. Axial thrust balance device with stacked rotor construction. Suitable for boiler feed pump and high building, long distance water transferring. The D series comprises single-casing radially split multistage between bearings pumps, referred to as BB 4 type pumps in API 610. These pumps are also known as ring section pumps, segmental ring pumps, or tie rod pumps. The modular design of the D series pumps allows us to find the most efficient solution to meet customer requirements. Both investment cost and lifecycle costs are taken into consideration when designing the best possible pump, and the optimized hydraulic design guarantees the highest level of efficiency. Structure Design Horizontal, radially split, ring section pump with radial impellers, single or double flow entry, multistage. The stages are sealed against each other by O rings or by metallic sealing faces and fastened by tie bolts. Features and Benefits * Greater reliability from radially split pressure casings, ensuring overall pump concentricity and rotor alignment. * Improved service life and tolerance to changing conditions due to precision-cast diffusers that equalize radial loads and increase bearing, wear ring and seal life. * Decreased maintenance costs and longer service intervals enabled by heavy- duty rotor with short bearing spans, which minimizes deflection. * Precise hydraulic configuration made possible by the modular segmental ring diffuser design plus numerous options. Top of its class efficiency to ensure lowest specific power consumption per produced cubic meter of water. Parameters of Multistage Centrifugal Water Pump D360-40X2-10 Flow Capacity 300-440 m3/h Delivery Head 71-420 m Inlet/Outlet Dia. DN200/DN200 mm Working Pressure ≤ 4.8 MPa Liquid Temperature 0 - 80 ℃ Driven By Electric Motor / Diesel Engine Seal Type Mechanical seal / Gland packing Liquid Clean water or similar Material of Construction Cast Iron / Cast Steel / S.S304 / S.S316 / Duplex S.S2205

Diamond grinding tool disc hardness 30-40 Rockwell machined parts. Description Diamond, which is a mineral composed of carbon elements, is an allotrope of graphite, with a chemical formula of C, and is also the original body of common diamonds. Diamond is the hardest substance naturally occurring in nature. The chemical composition of diamond is C, which is a homogeneous and polymorphic variant of carbon with graphite. In the chemical composition of minerals, it always contains elements such as Si, Mg, Al, Ca, Mn, Ni, and often contains impurity elements such as Na, B, Cu, Fe, Co, Cr, Ti, and N, as well as carbohydrates. The crystal structure of diamond mineral belongs to the equiaxed tetrahedral structure of homopolar bond. The carbon atoms are located at the corners and the center of the tetrahedron and have a high degree of symmetry. The carbon atoms in the unit cell are connected by homopolar bonds with a distance of 154pm. Common crystal forms are octahedron, rhombic dodecahedron, cube, tetrahedron and hexaoctahedron, etc. What are the Diamond Grinding Disc replacement conditions? 1, wear problem Any grinding wheel has its certain use and wear requirements. If the wear condition reaches a certain level, it must be replaced with a new one. It can not be used in order to save material, it is an extremely unsafe violation. Generally, when the grinding wheel wears to a diameter 10mm larger than the diameter of the chuck, it should be replaced with a new one. 2, validity period The new wheels removed from the warehouse are not necessarily qualified wheels, and even new wheels purchased from manufacturers are not necessarily qualified wheels. Any grinding wheel has a certain expiration date. If it is used within the expiration date, it is a qualified grinding wheel; if it is used beyond the expiration date, it is not necessarily a qualified grinding wheel. The regulations stipulate that "the grinding wheel should be used within the validity period, and the resin and rubber bond grinding wheel must be subjected to a rotation test after storage for one year before it can be used". 3, texture issues If cracks are found in the grinding wheel during use, you should stop using it immediately and replace it with a new one, so as to avoid accidents caused by grinding wheel breakage. CNC Machining Description Product name Diamond grinding tool disc hardness 30-40 Rockwell machined parts Material 42Crm Alloy steel Surface Treatment Tin and CBN Surface roughness Ra0.5~2um Material standard ASTM Operating RPM500-30000, coaxiality<0.05mm Hardness 30-40 Rockwell Service available OEM /ODM/Customized/Design Process CNC Machining,Tin and CBN plating Drawing Format 3D/CAD/Dwg/IGS/STP Features High precision, high strength, high quality

Mirror Polishing Customized OEM Precision CNC Machining Parts Our services WeiLIN is a world-class manufacturing service provider in ShangHai. We got advanced equipment to provide all-around customized products for manufacturers around the world, focusing on CNC processing . Our goal is to make customization easy. so to have your products and brands stand out, we can not only process hundreds of materials, with stainless steel,aluminum, bronze, brass, copper, plastic, titanium steel , and skilled technicians provide you with a variety of high-quality surface treatment services, such as anodizing, sandblasting, powder coating, roll coating, part marking, heat treatment, precious metal plating. We welcome your drawings and will follow them to make the samples for you.we could manufacture the goods according to your samples or drawings also Product processing capacity ? 1. Main Materialsa Stainless Steel SS201,SS301,SS303, SS304, SS316, SS416 etc. Steel mild steel, Carbon steel, 4140, 4340, Q235, Q345B, 20#, 45# etc. Brass HPb63, HPb62, HPb61, HPb59, H59, H68, H80, H90 etc. Copper C11000,C12000,C12000, C36000 etc. Aluminum AL6061, Al6063, AL6082, AL7075, AL5052, A380 etc. Iron A36, 45#, 1213, 12L14, 1215 etc. Plastic ABS, PC, PE, POM, Nylon, PP, Peek etc. 2. Surface Treatment Stainless Steel Polishing, Passivating, Sandblasting, Laser engraving Steel Zinc plating, Oxide black, Nickel plating, Chrome platingk, Carburized, Powder Coated Aluminum parts Clear Anodized, Color Anodized, Sandblast Anodized, Chemical Film,Brushing,Polishing Plastic Plating gold (ABS), Painting, Brushing (Acylic), laser engraving 0.01mm SS201 CNC Precision Machined Parts OEM CNC Turning Milling Parts 0 0.01mm SS201 CNC Precision Machined Parts OEM CNC Turning Milling Parts 1 0.01mm SS201 CNC Precision Machined Parts OEM CNC Turning Milling Parts 2

Product Description Press cover Stainless Steel or iron ZF4083d Ra1.6 Dia.26.8mm 0.02 mm tolerance metal machining parts customized Description: Tolerance 0.02mm metal machining parts, made of stainless steel 201/303/304/316 ect. Parameters: product name Press cover/screw nut application kitchen tap diameter D26.8 +/-0.02mm thread M36x1.25 tolerance proceed as Standard GB/T 1800.1-2009 IT12 raw material die casting / stainless steel thread checking standard go gauge surface no burs, no deformation Our winning strategy: provide value-added engineering services. assist you in material selection, structural testing, machining, and final product arrangement. one-stop customized processing service. Pre-sale service 1. We have full stock and can deliver within short time. 2. OEM and ODM order are accepted, Any kind of logo printing or design are available. 3. Good Quality + Factory Price + Quick Response + Reliable Service, is what we are trying best to offer you. 4. All of our products are produced by our professional workman and we have our high-work-effect foreign trade team, you can totally believe our service. After you choose 1. We will count cheapest shipping cost and make invoice to you at once. 2. Check quality again, then send out to you at 1-2 working day after your payment 3. Email you the tracking number and help to chase the parcels until it arrives you.