Office & School Furniture

I. Product introduction. 　　The practical training system is based on the real car lighting system, integrating all relevant control switches and actuators into a demonstration board, which systematically shows the working principle of the car lighting system. It can be used for demonstration experiments, fault diagnosis, data measurement and other practical training operations of automotive headlights, taillights, hazard warning lights and other systems. 　　 II. Functional features. 　　1. Real runnable automotive lighting system, fully demonstrate the composition of the automotive lighting system structure and work process. 　　2. Training table integrated placement of the left headlight assembly, right headlight assembly, front fog light assembly, left rear tail light assembly, right rear tail light assembly, combined instrumentation, body control unit, gateway control unit, combined light switch, etc. 　　3. The training bench measurement panel is painted with colorful spray- painted circuit diagrams, installed with detection terminals, which can directly detect the electrical signals of each headlight, rear taillight and body control unit pin on the panel, such as resistance, voltage, current, frequency signals, etc. 　　5. The training bench is equipped with fault setting system, which can set one and more common faults to simulate the circuit faults of automobile lighting system to achieve the purpose of examination and assessment. 　　6. The training table is installed with diagnostic socket, which can be connected to special or general-purpose cars to read fault codes, clear fault codes, read data streams and other self-diagnostic functions of the automotive lighting system. 　　 III. The material and process. 　　1. Training table measurement panel using 8mm thickness of high-strength acrylic sheet spray-painted, with a large temperature difference, wear- resistant, moisture-proof, anti-corrosion, not easy to deformation, long service life, bright colors, not easy to fade and other characteristics. 　　2. Training table made of high-grade steel, with high strength, corrosion resistance, long life, etc., without the need to go through the spraying process, more environmentally friendly, more beautiful and high-grade appearance, the table with self-locking casters device, mobile and flexible, safe, reliable, durable. 　　3. Training table with two practical and beautiful drawers for placing daily teaching supplies. 　 　　 IV. Teaching content: 1. 　　1. Knowledge of the configuration of automotive lighting system 　　2. Understand the control principle of automotive lighting system 　　3. Master the basics of automotive lighting system 　　4. Master the working principle of the lighting system 　　5. Be able to independently enumerate and explain the components of the lighting system 　　6. Master the operating conditions of the actuators of the lighting system 　　7. Independently troubleshoot, maintain and repair the automotive lighting system 　　 V. Technical parameters. 　　1. External dimensions: 1600 × 700 × 1800mm (L × W × H) 　　2. Input power supply; AC 220V ± 10% 50Hz 　　3. Working power supply; DC12V

Minimum Order: 1 bags

I. Product Overview The equipment adopts the Volkswagen Passat car electronic electrical system as the basis, fully demonstrating the composition structure and working process of the car instrumentation system, lighting system, wiper system, starter system, charging system and ignition system. II. Functional requirements 1. Real runnable car electronic and electrical systems, fully demonstrate the composition of the car instrumentation system, lighting system, wiper system, starter system, charging system and ignition system structure. 2. Manipulate various electrical switches and buttons to demonstrate the working process of automobile instrumentation system, lighting system, illumination system, wiper system, starting system, charging system and ignition system. 3. Each electrical component line terminal on the training table panel is equipped with a measurement port, refer to the supporting circuit diagram or maintenance information, using oscilloscopes, multimeters and other instruments, the students can exercise the ability to read diagrams and measure various signals. 4. There are test terminals installed on the panel of the training table, which can directly detect the electrical signals of each circuit element of the auto body electrical system on the panel, such as resistance, voltage, current, frequency signals, etc. 5. The training table is made of high-quality steel welding, with high strength, corrosion resistance, long life, etc. After spraying process, the appearance of beautiful and high-grade, the table with self-locking casters, mobile and flexible, safe, reliable, durable. III. Specification parameters Size: 2400*800*1800mm Power supply: DC12V Motor power supply: AC380V

Minimum Order: 1 bags

【Product Introduction】 The training bench uses Toyota A340E original electric automatic transmission as the basis, speed control three-phase motor as the power source, the automatic transmission can be gear display, gear shift and other test conditions of actual operation. Real display of electric automatic transmission composition structure and principle and working process. Suitable for all types of colleges and training institutions on the theory of electronically controlled automatic transmission and maintenance training needs of practical training. The training table training function is complete, easy to operate, safe and reliable, beautiful and generous. 【Structure composition】 Toyota A340E automatic transmission assembly, automatic transmission control unit, gear lever assembly, transmission oil heat sink, instrumentation, three- phase speed control motor, throttle body assembly, engine crankshaft sensor and signal panel, diagnostic socket, pressure gauge, fault setting system, the original car circuit schematic board and detection terminals, mobile stand, etc. Equipped with practical training guide and operating instructions for the stand. The sensors and actuators are installed with digital display table, main oil pressure gauge, casters with locking universal, stainless steel hand guard, high temperature and rotating parts of the table are equipped with protection devices. 【Functional features】 1. Automatic transmission normal operation, diode display solenoid valve working condition. 2. Fault simulation system can simulate the actual operating conditions, set a variety of real car automatic transmission common faults. 3. Pointer type pressure gauge indicates the main oil pressure value. 4. The training table panel is painted with colorful spray-painted circuit diagrams, spray-painted with Plexiglas protection, students can intuitively control the circuit diagrams and engine objects, recognize and analyze the working principle of the control system. 5. The training table panel is installed with detection terminals, the panel can directly detect the sensors, actuators, such as resistance, voltage, current, frequency, waveform signal, etc. 6. Equipped with the original car diagnosis seat, you can use the computer diagnostic instrument to read the fault code and data flow of the automatic transmission electronic control system. 7. The training bench is equipped with a power switch, and other rotating parts of the protective cover and other safety protection devices. 8. The transmission can be used for various practical training projects. The transmission can be shifted/automatic gear lift and other practical tests. 9. The base part of the training table adopts steel structure welding, panel cabinet stamping and forming, panel cabinet and base can be separated, the surface of the table frame adopts baking paint technology, with universal self- locking casters device. 10. Appearance size: 1500mm X 1000mm X 1700mm (length X width X height), weight: 200KG

Minimum Order: 1 bags

Product introduction The equipment adopts the rear-drive automobile chassis systems as the basis, fully demonstrating the composition structure of the chassis systems. Including front and rear suspension system, steering system, transmission system, manual transmission and gear mechanism, braking system and other systems, the installation of casters removable table and other components. Applicable to the teaching needs of the school for the theory and maintenance of the chassis systems practical training. The functional characteristics 1. Install the real chassis systems (including front and rear suspension, steering, transmission, manual transmission and gear mechanism, braking system), fully demonstrate the composition of the structure of the chassis systems. 2. Can be true to the car chassis systems show and disassembly training. 3. Dissected manual transmission can be dynamic demonstration and testing, reducer motor input power, the transmission can be shifted and dynamic testing, four wheel contact with the ground can be slow driving demonstration. 4. Motor-driven directional power pump, real demonstration of power steering work process. 5. The base of the training bench is welded with steel structure, the surface is treated with spraying technology, with self-locking casters, flexible movement, safe, reliable, durable. Technical specifications Power supply: 220V Working temperature: -40℃～+50℃ Host: the original device Electric motor: 220V/250W 15rpm Leakage protection switch: DZ47LE-32 Steel pipe: 60*40*3mm Mobile casters: 100*50mm Weight: 500KG Size: 3500mm * 2000 * 1200

Minimum Order: 1 bags

I. Product requirements The equipment adopts the real parts of the electric control system of Volkswagen Jetta ATK engine to fully demonstrate the composition structure and working process of the engine electric control system. II. The functional requirements 1. The real runnable engine electronic control system, simulating the engine crankshaft operation, can produce spark plug ignition, fuel pump work, injector injection and other executive components work, fully demonstrate the composition of the engine electronic control system structure and work process. 2. The training table measurement panel is painted with colorful spray-painted circuit diagrams, using 4mm thickness of high-strength aluminum plastic plate spray-painted, with a large temperature difference, wear-resistant, moisture- proof, anti-corrosion, not easy to deformation, long service life, bright colors, not easy to fade, etc.; students can intuitively control the circuit diagrams and physical, recognize and analyze the working principle of the engine electronic control system. 3. The teaching board panel is installed with detection terminals, which can directly detect the electrical signals of the engine electric control system circuit components on the panel, such as resistance, voltage, current, frequency signals, etc. 4. There is a diagnostic socket installed on the panel of the teaching board, which can be connected to a special or general-purpose car decoder to read fault codes, clear fault codes and other self-diagnostic functions of the engine electronic control system. 5. The training table is built of high-grade steel, with high strength, corrosion resistance, long life, etc., without the need to go through the spraying process, more environmentally friendly, more beautiful and high-grade appearance, the table frame with self-locking casters, mobile and flexible, safe, reliable, durable. 6. The teaching board works with ordinary 220V AC power supply, converted into 12V DC power supply by internal circuit voltage rectification, without battery, reducing the trouble of charging, 12V DC power supply has anti-short circuit function. III. Specifications Size: 1600 * 800 * 1800mm (L * W * H) Power supply: AC220V

Minimum Order: 1 bags

I. Product introduction. 　　The practical training system is based on real automotive sensors and actuators, integrating all relevant control switches and actuators into a demonstration board, which systematically shows the working principle of automotive sensors and actuators. It can carry out demonstration experiments, fault diagnosis, data measurement and other practical training operations of automotive sensors and actuators. 　　 II. Functional features. 　　1. Real runnable automotive sensors and executive equipment, fully demonstrate the composition structure and working process of the car. 　　2. The training table measurement panel is painted with colorful spray- painted circuit diagrams, installed with detection terminals, can be directly on the panel to detect the electrical signals of sensors and control units such as executive equipment pins, such as resistance, voltage, current, frequency signals, etc. 　　3. Composition: crankshaft angle sensor, A/T pulse generator sensor, cam position sensor, ABS wheel sensor, humidity sensor, AQS sensor, engine temperature sensor, auto light sensor, blast sensor, speed sensor, gas pedal position sensor, oxygen sensor, throttle position sensor, air flower sensor, map sensor, safety sensor 　　 III. Materials and processes. 　　1. Training table measurement panel using 8mm thickness of high-strength acrylic sheet spray-painted, with a large temperature difference, wear- resistant, moisture-proof, anti-corrosion, not easy to deformation, long service life, bright colors, not easy to fade and other characteristics. 　　2. Training table made of high-grade steel, with high strength, corrosion resistance, long life, etc., without the need to go through the spraying process, more environmentally friendly, the appearance of more beautiful and high-grade, the table with self-locking casters device, mobile and flexible, safe, reliable, durable. 　　3. Training table with practical and beautiful drawers for placing daily teaching supplies. 　 　　 IV. Teaching content. 　　1. Cognition of the configuration of automotive sensors and actuators 　　2. Understand the control principle of automotive sensors and actuators 　　3. Master the basics of automotive sensors and actuators 　　4. Master the working principle of sensors and actuators 　　5. Be able to independently enumerate and explain the components of sensors and actuators 　　6. Master the operating conditions of the actuators of sensors and actuation equipment 　　7. Independently troubleshoot, maintain and repair automotive sensors and actuating equipment 　　 V. Technical parameters. 　　1. External dimensions: 1600 × 700 × 1800mm (L × W × H) 　　2. Input power supply; AC 220V±10% 50Hz 　　3. Working power supply; DC12V

Minimum Order: 1 bags

Product requirements The equipment adopts the real parts of Toyota Corolla 1ZR-FE engine electronic control system, which can fully demonstrate the composition structure and working process of the engine electronic acceleration system. The functional requirements 1. Real runnable engine electronic control system, simulate engine crankshaft operation, can produce spark plug ignition, fuel pump work, injector injection and other executive components work, fully demonstrate the composition of the engine electronic control system structure and work process, electronic throttle pedal can control the opening of the throttle. 2. The training table measurement panel is painted with colorful spray-painted circuit diagrams, using 4mm thickness of high-strength aluminum plastic plate spray-painted, with a large temperature difference, wear-resistant, moisture- proof, anti-corrosion, not easy to deformation, long service life, bright colors, not easy to fade, etc. Students can intuitively control the circuit diagrams and physical, recognize and analyze the working principle of the engine electronic control system. 3. The teaching board panel is installed with detection terminals, which can directly detect the electrical signals of the engine electric control system circuit components on the panel, such as resistance, voltage, current, frequency signals, etc. 4. The teaching board panel is installed with a diagnostic socket, can be connected to a special or general-purpose automotive decoder, the engine electronic control system to read fault codes, clear fault codes and other self-diagnostic functions of the engine electronic control system. 5. The training table is made of high-quality steel welding, with high strength, corrosion resistance, long life, etc., after spraying process, the appearance of beautiful and high-grade, the table with self-locking casters, mobile and flexible, safe, reliable, durable. 6. The teaching board works with ordinary 220V AC power supply, which is converted into 12V DC power supply by the internal circuit, without battery, reducing the trouble of charging, and the 12V DC power supply has anti-short circuit function. Specifications Size: 1600 * 800 * 1800mm (L * W * H) Power supply: AC220V

Minimum Order: 1 bags

Product Overview: This training bench is composed of Wuling B12 electronically controlled gasoline engine assembly, the training bench can start the engine, running experiments, the teacher combined with the training bench teaching panel to teach the engine control principle to train students to analyze and solve the actual fault ability, forming an organic combination of theory and practice; suitable for secondary and higher vocational and technical schools and automotive training institutions of automotive engine construction and maintenance practical training teaching It can meet the teaching needs of different levels of schools on the structural composition, working principle, fault setting and diagnosis of electronically controlled gasoline engines. Main components: Engine assembly, engine electronic control unit, instrumentation, ignition switch, fault setting system, oil pressure gauge, vacuum gauge, fuel tank, battery, diagnostic socket, cooling system (water tank, fan, fan cover, upper and lower water pipe), exhaust system, and the engine computer pin one to one correspondence of the signal detection area, LED lights, signal table, safety cover, removable table, etc. Functional characteristics: (1) The engine works normally, a real response to the structural composition and working process of the EFI gasoline engine. (2) Engine training table with dynamic operation and display functions, the original instrumentation, digital table real-time display of dynamic and static engine signal parameters. (3) Assembled with LED lights to show the working state of injector pulse and ignition pulse-related components. (4) Teaching panel installed with a complete color engine electronic control system circuit working principle diagram, ECU terminal function, injection system LED indication, etc., to facilitate the teacher to explain the system knowledge more intuitively. (5) The training table is installed with a diagnostic socket, which can be connected to a special or general-purpose car decoder to read fault codes, clear fault codes, read data streams and other engine self-diagnostic functions for the engine electronic control system. (6) Self-diagnostic functions: dynamic and static data stream reading, fault code reading, waveform analysis, actuating element action test, etc. (7) Electronic control system detection function: the teaching panel is installed with computer lead terminals, which can use multimeter and oscilloscope to detect each sensor and actuator resistance, voltage, frequency, waveform. (8) The training table is equipped with a fault-setting assessment device suitable for teaching, which can set one and more common faults to meet the assessment requirements of vocational skills teaching. (9) The training table measurement panel is painted with colorful spray-painted circuit diagrams, using 4mm thickness of high-strength aluminum spray-painted panels, with a large temperature difference, wear-resistant, moisture-proof, anti-corrosion, not easy to deformation, long service life, bright colors, not easy to fade and other characteristics. (10) Training table using international standard steel welding, with light quality, high strength, corrosion resistance, long life, etc., after spraying process, the appearance of more beautiful high-grade, the table with self- locking casters device, mobile and flexible, safe, reliable, durable. Technical parameters. Table size: 1500 * 1000 * 1700mm (L * W * H) Working power: 12VDC Fuel standard: 92# Weight 150KG

Minimum Order: 1 bags

Product Overview: The training bench is composed of Buick Verano LG3 electronically controlled gasoline engine assembly, the training bench can start the engine, run experiments, the teacher combined with the training bench teaching panel to teach the control principle of the engine to train students to analyze and solve the actual fault ability, forming an organic combination of theory and practice; suitable for secondary and higher vocational and technical schools and automotive training institutions of automotive engine construction and maintenance training Practical teaching, to meet the different levels of schools on the structure of electronically controlled gasoline engine components, working principles, fault settings and diagnosis of teaching needs. The main components: engine assembly, engine electronic control unit, instrumentation, ignition switch, fault setting system, oil pressure gauge, vacuum gauge, fuel tank, battery, diagnostic socket, cooling system (water tank, fan, fan cover, upper and lower water pipe), exhaust system, and the engine computer pin one to one correspondence of the signal detection area, LED lights, signal table, safety cover, removable table, etc. Functional features : (1) The engine works normally, a real response to the structural composition and working process of the EFI gasoline engine. (2) Engine training table with dynamic operation and display functions, the original instrumentation, digital table real-time display of dynamic and static engine signal parameters. (3) Assembled with LED lights to show the working state of injector pulse and ignition pulse-related components. (4) Teaching panel installed with a complete color engine electronic control system circuit working principle diagram, ECU terminal function, injection system LED indication, etc., to facilitate the teacher to explain the system knowledge more intuitively. (5) The training bench is installed with a diagnostic socket, which can be connected to a special or general-purpose car decoder to read fault codes, clear fault codes, read data streams and other engine self-diagnostic functions for the engine electronic control system. (6) Self-diagnostic functions: dynamic and static data stream reading, fault code reading, waveform analysis, actuating element action test, etc. (7) Electronic control system detection function: the teaching panel is installed with computer lead terminals, which can use multimeter and oscilloscope to detect each sensor and actuator resistance, voltage, frequency, waveform. (8) The training bench is equipped with a fault-setting assessment device suitable for teaching, which can set one and more common faults to meet the assessment requirements of vocational skills teaching. (9) The training bench measurement panel is painted with colorful spray-painted circuit diagrams, using 4mm thickness of high-strength aluminum spray-painted panels, with a large temperature difference, wear-resistant, moisture-proof, anti-corrosion, not easy to deformation, long service life, bright colors, not easy to fade and other characteristics. (10) Training bench using international standard steel welding, with light quality, high strength, corrosion resistance, long life, etc., after spraying process, the appearance of more beautiful high-grade, the table with self- locking casters device, mobile and flexible, safe, reliable, durable. Technical parameters: Table size: 1500 * 1000 * 1700mm (L * W * H) Working power: 12VDC Fuel standard: 92# Weight 150KG

Minimum Order: 1 bags

First. Product Overview The equipment uses the Volkswagen Passat V6 2.8L electronically controlled gasoline engine as the basis for production, the engine can be started, acceleration, deceleration and other working conditions of the practice operation, the real display of the V6 electronically controlled gasoline engine composition structure and work process. Second. The functional characteristics 1. Real running Volkswagen Passat V6 2.8L electronically controlled gasoline engine, fully demonstrating the composition of the structure and working process of electronically controlled gasoline engine. 2. The training bench measurement panel is painted with colorful spray-painted circuit diagrams, using 4mm thickness of high-strength aluminum composite panel UV spray-painted, with a large temperature difference, wear-resistant, moisture-proof, anti-corrosion, not easy to deformation, long service life, bright colors, not easy to fade, etc.; students can intuitively control the circuit diagram and electronically controlled gasoline engine in kind, recognize and analyze the working principle of the control system. 3. There is a car instrument installed on the training bench panel, which can display the engine speed, water temperature, oil pressure light, charging indicator, electric control system fault indicator and other parameter changes in real time. 4. The training bench panel is installed with detection terminals, which can directly detect the electrical signals of sensors, actuators and engine control unit pins on the panel, such as resistance, voltage, current, frequency signals, etc. 5. The training bench is installed with diagnostic socket, which can be connected with special or general-purpose car decoder to read fault codes, clear fault codes, read data streams and other self-diagnostic functions for the engine electronic control system. 6. The training bench is equipped with throttle control device, which can facilitate the acceleration and deceleration of the engine. 7. The training bench is equipped with a power switch, water tank guard, flywheel guard and other installation protection devices. 8. The training bench is made of high quality steel welded, with high strength, corrosion resistance, long life, etc. After spraying process, the appearance is beautiful and high-grade, the table frame with self-locking casters, flexible movement, safe, reliable, durable. Three. Specification parameters Product size: 1300*1000*1800mm (L*W*H) Power supply: DC12V

Minimum Order: 1 bags

Product Introduction The equipment adopts Volkswagen Jetta 1.4T electronically controlled gasoline engine as the basis, which can be used for the practical operation of engine starting, acceleration, deceleration and other working conditions, truly demonstrating the composition structure and working process of electronically controlled gasoline engine, easy to operate, safe and reliable. Suitable for higher vocational and technical colleges, general education colleges and training institutions on automotive engines and maintenance of practical training teaching needs. Main configuration Engine assembly, the original engine computer, combined instrumentation, engine start and run all relevant original accessories, fault setting and troubleshooting system, the original circuit schematic and testing terminals, large-capacity battery, stainless steel fuel tank, engine acceleration mechanism, console, removable table, table power switch, diagnostic socket, cooling system, digital display table, fuel pressure gauge, vacuum gauge, with locking universal casters, etc. Product features 1, The training bench measurement panel painted with colorful spray-painted circuit diagram, using 8mm thickness of high-strength acrylic sheet spray- painted, with a large temperature difference, wear-resistant, moisture-proof, corrosion-resistant, not easy to deformation, long service life, bright colors, not easy to fade and so on. 2, The operating panel of the training bench is installed with automotive instrumentation, fuel pressure gauge, vacuum pressure gauge, can real-time display engine speed, fuel pressure, intake manifold pressure and other parameter changes. Diagnostic socket is installed, which can be connected with special or general-purpose car decoder to read fault codes, clear fault codes, read data streams and other self-diagnostic functions for the engine electronic control system. Equipped with throttle control device, which can facilitate the acceleration and deceleration of the engine. 3、There are testing terminals installed on the panel of the training bench, which can directly detect the electrical signals of sensors, actuators and engine control unit pins on the panel, such as resistance, voltage, current, frequency signals, etc. 4、The training bench is built with international standard aluminum alloy profile, with light quality, high strength, corrosion resistance, long life, etc., without the need to go through the spraying process, more environmentally friendly, the appearance of more beautiful and high-grade, the table with self- locking casters, mobile and flexible, safe, reliable, durable. Technical parameters 1. Dimension: 1500×1000×1800mm (L×W×H) 2. Working power: DC 12V 3 fuel grade: 92# 4. Fuel tank volume: 10L

Minimum Order: 1 bags

Product Description Modern Melamine Board Panel Furniture 1200mm 2 Doors Wooden Office File Storage Cabint Decorative Cabinet Product Description Description Model no.: BL-29BOB302 Size: L1200*W400*H1600mm or size made by customer's request Brand XINYUANBAILI Material: E1 Grade MFC Veneer thickness: 0.3MM thickness wood veneer. Place of Product Guangzhou ,China PriceTerms: EXW, FOB shenzhen Color: Kaldi color, Walnut color, dark , brown or more colours available Payment Terms: 30%T/T BALANCE BEFORE LOADING OR, WEST UNION Delivery Time: 15-20days after deposit. Features: 1. high density foam inside, comfortable and not easily deformed. 2. big size, suitable for boss and manageral level. 3. Doll cotton on the back cushion, much more comfortable. 4.Back tilt tension, tilting &locking control in different angles, easily adjusted according to human ergomic design. 5.seat height adjust up & down easily according to needs. 6.back support, with lumbar support height adjustable for lumber protection. 7. 5-layer carton, hard enough to protect the chair. 8. 1pc/ctn, convinient to sell again. ΔPayment Terms & Shipping: 1.Price Term: FOB, EXW, etc. 2.Payment: 30% as deposit, the balance will be paid when cargo ready before shipment, all by T/T 3.Loading Seaport:Guangzhou, Shenzhen. 4.Delivery Time:15-20days( Estimated delivery may be affected by holidays.) ΔPacking 1.Packing in carton and fabric. 2.As customers demand. Advantage Good Raw Material All wooden furniture made of high quality E0 or E1 board, The metal hardware are strong and durable The glue and other raw material used in the furniture all are environment protection no harm for the health. The office chairs foam all use high density new foam, gas lift pass BIFMA, SGS Good Workshop All office furniture produced by advanced machine , and Skilled professional workers. The office chairs sewing and upholstery all by more than 3 years skilled workers with good workmanship All finished products with color correction and good clean, all the products are 100% QC inspection. Good Packing All Furniture with knock down packing Inside the packing with instruction manual easy for customer to assemble the furniture. Each products with EPE or foam protection, outside with double strong carton boxes packing. All the carton boxes outside print/stick customer's shipping mark. Company Information Guangzhou Bali Furniture Co.,Ltd is a medium size furniture manufactory, which located in Guangzhou city, China. We specilized in producing office furniture,school furniture, hotel furniture and Auto 4S limited furniture customization,etc. Our main products territories contain office table , swivel chair, partition/screen, office sofa,reception counter , meeting table,visitor chair , student desk/chair,auditorium chair, public chair,filing cabinets and various kinds of office series furniture of complete project. The projects that we have cooperated include Nissan, Dongfeng Honda, Guangqi Hongda,Toyota, Trumpchi etc all over China. We also have established good business relationship with clients worldwide.The main markets are Europe, Middle east and Asia. With the principle of quality first , customer utmost , credit oriented,service based , value glorious' . We positively advocate national furniture culture , also integrate the international furniture trends ,and constantly use endless creativity with the combination of Chinese and Western art culture in designing and manufacturing many elegantly-shaped and trend leading new products, adding ending endless joy to today's high efficiency life in the office. FAQ Q.What's your main products in your company? A:Our main product are: school and office furniture,including children furniture , student desk , dormitory furniture , training & metting furniture , dinning tables Laboratory Furniture,computer desk and chair Q: Are you a factory or trading company? We are a factory was founded in 2015.We are committed to providing a one-stop shopping for school furniture purchasing solutions for global schools. Q:About the H.S. Code? A: School Desk : 9403200000 Desk Top :4410120000 Plastic Desk : 9403700000 Student chair: 9401719000 Q : How soon can we get a sample of the product? A : Within 1 week. We can sent the samples via international courier like Fedex,UPS,DHL and TNT. Q:How long is your production lead time? A:It depends on product and order qty. Normally, it takes us 20 days for an order with qty 500 PCS Q: Do you provide OEM developing services? A: Yes, we have plenty experience in OEM developing. Customer's OEM project is welcome. Q:What is your payment term? A:Normally we accept payment term as 30% deposit after order signed and 70% balance against the copy of B/L. Q:Can we use our own shipping agent? A:Yes,you can.We had cooperated with many forwarders.If you need,we can recommend some forwarders to you and you can compare the prices and service. Q:Our port of shipment? A:Huangpu or Shenzhen(China) Q:If i want to visit your factory,which is the nearest airport ? A:Guangzhou Baiyun airport is the nearest airport.We warmly welcome clients to come to our factory for visit and cooperation. Any question please feel free to contact me. I will be glad to be your assistant.

Brand: Monisa style: combination Material: Leather Function: stretch function style: Italian minimalist Applicable occasions: home theater Frame: Metal Frame Color: Four (including electric coffee table with function) Size: High matching top layer yellow cowhide (contact surface), crushed top layer yellow cowhide (contact surface), microfiber imitation leather (contact surface), custom can consult customer service Negative: yes Internal filling: high density sponge Whether electric: yes Whether it can be multi-functional combination: yes Whether intelligent control: yes Applicable parts: legs Function: USB interface, electric, multi-function, folding, stand, open Smart Furniture, Functional Furniture, Italian Minimalist Matching, Functional Sofa, Cinema Sofa, Foot Spa Furniture, Bedroom Furniture, Living Room Furniture, Public Place Furniture, Leisure Furniture, Home Product Design, Dining Room Furniture, Functional Cinema Sofa, Electric Rocking Chair, Multifunctional Sofa, Space Capsule Seat Sofa, Space Cinema Sofa, Sofa, Chair, Sofa Bed, Massage Chair, Massage Sofa, electric function sofa, manual function sofa, function chair, Function Sofa, leisure sofa, Electric Multifunctional Sofa, Multifunctional Sofa

Item Name: Commercial Adjustable Executive Office Chair Swivel High Ergonomic Model No.: KT-292-1-STLM Type: Leather office chair Specification: Net Weight: 0.6kgs / Gross Weight: 1kgs / Size:Standard size Material: Office Furniture Specific Use: OFFICE CHAIR Customized: available ergonomic chair Container loading: 488pcs/40HQ Certificate: 4pcs/CTN Lumbar Support: Adjustable Available Trade Terms: EXW /FOB /CFR /CIF Color Available: black green white brown and so on Frame: Black/White Material: Fabric/Mesh, mesh back & fabric padded seat MOQ : 9 sets Key Feature3: Office boss chair Seat Cushion: Mould Foam Color of task chair: back: white or black for choose 2.L/C:irrevocable L/C at sight are acceptable.