Pumps

AY type high temperature centrifugal oil pump is divided into six structures: single-stage single-suction cantilever type, two-stage single-suction cantilever type, single-stage single-suction cantilever type, single-stage double-suction double-support type, two-stage single-suction double-support type and two-stage single-suction double-support type. AY type high temperature centrifugal oil pump is especially suitable for conveying high temperature and flammable, explosive or toxic liquid. The installation method is horizontal center line support. The suction flange and outlet flange of the pump are cast on the pump body and are vertically upward. The bearing chamber (packing box) and the pump cover are cast into one, which can be used for packing seal, balanced type, flow type and series mechanical seal. An optional jacket of a water-cooled chamber is cast outside the shaft seal chamber. The water-cooled chamber shall be specially provided or provided when the conveying medium is water with a temperature exceeding 66 ° c and hydrocarbon action exceeding 150 ° c. Impeller for the whole casting, and through static balance check, the axial force of the pump mainly depends on the impeller balance hole to balance. The bearing body is equipped with a set of radial ball bearings and a set of thrust ball bearings mounted back to back. The bearings are lubricated with thin oil of oil swing ring. The external surface of the bearings is cast with heat sink, which can be cooled by air (T <120℃), fan cooling (T =120-260℃) and water cooling (T =260-420℃). Pump maintenance does not have to disassemble the suction or discharge pipeline. It is easy to disassemble the impeller, shaft, bearing, shaft seal and other parts. The shaft seal adopts mechanical seal. The pump is driven directly by a motor through a flexible diaphragm extension coupling. Viewed from the direction of the motor, the pump rotates counterclockwise. AY type high temperature centrifugal oil pump can be used in petroleum refining, petrochemical and chemical industries and other places to transport petroleum, liquefied petroleum gas and other media without solid particles. Flow: 1 to 612m3/h Head: 370 to 670m Liquid temperature: -20 to 400Degree Celsius. Pump material: cast iron, cast steel, alloy steel

Minimum Order: 1 bags

HD high efficiency drum pump is used to transport the ordinary medium and all kinds of strong acids and alkali, and inflammable and explosive liquids(Oils) in standard 200L barrel. Stepless adjustable speed motor, with the advantages of low noise and small impact, and equipped with overheat protection device, to prevent the motor burning for overload, thus ensuring the high reliability and durability of the motor. Pump body and motor with screw flange installation disc, convenient disassembly and installation without any tools. No leakage: no leakage design of the pump pipe, more suitable for the delivery of corrosive chemical liquid. Overload protection: the motor is equipped with overload protection device. Light weight: the total weight of pump and motor is 4-10kg, easy to carry and move. Quick: 2-3 minutes to empty a 200L standard barrel. No shaft seal: no leakage structure, no need to use mechanical seal, reduce maintenance cost. A variety of materials: polypropylene, PVDF, stainless steel, aluminum alloy material is suitable for most low middle viscosity liquid transport to meet more than 80% of the application. A variety of driving methods: electric or pneumatic drive, to meet different power sources. Humanized design: ergonomic appearance design, easier for the operator to use. Pumped liquids: it can transport ordinary medium and all kinds of strong acids and alkali, and inflammable and explosive liquids. Convenient interface: standard G1 "screw outlet, suitable for connecting all kinds of joints. Improved coupling: no alignment is required to install and only a few seconds to connect. Quick interface: the motor and pump pipe adopt quick interface, disassemble and assemble freely. Integral quick-release construction: no auxiliary tools are required for disassembly and assembly. Dry operation: self-lubricating bearings can be dried for a short time without damaging the pump line. High performance impeller: high performance open impeller with both large flow and high head. Maximum flow rate: 210L/m (electric), 80 l/m (pneumatic) maximum head: 23m (electric), 11m (pneumatic) maximum temperature: PP: 50℃, PVDF: 100℃, SS: 110℃ viscosity range: 0-2000cps (electric) maximum weight: 1.8 Pump line length: 1000mm drive mode: electric motor or pneumatic motor

Minimum Order: 1 bags

DP miniature diaphragm booster water pump 1 - Low noise, resistance to weak acid and alkali corrosion, oil resistance, high pressure, self-imbibition height 5m. 2 - The medium temperature can reach 60℃. 3 - Allow dry operation. 4 - Pressure switch is installed to protect the pump from damage during operation. 5 - The built-in overflow valve controls the normal operation of the pump. 6 - Easy to disassemble and assemble. 7 - Use safe low voltage to ensure personal safety. (12VDC/24VDC) 1 - Miniature diaphragm pump is suitable for household tap water pressurization, car washing, ship sea water desalination. 2 - It is applicable to reverse osmosis pure water machine, water treatment equipment, filter, spray device, chemical metering and liquid, sanitation, environmental protection, printing and other industries. Maximum flow rate: 1~ 12.5l /min Maximum pressure: 0.24~ 0.9mpa Power: 10 ~ 40 w Voltage: 12 ~ 24 VDC Pump body material: FRPP Diaphragm material: EPDM plastic, butyl rubber(NBR) 1 - Provide water for food, washing, bath, toilet and flushing for vehicles, ships and yachts in use. (a) water supply system for toilets of high, medium and low grade passenger cars and water dispensers;(b) water supply system for all kinds of recreational vehicles, field camping vehicles and family recreational vehicles;(c) other special vehicles, such as blood collection vehicles, ambulances, TV relay vehicles, survey vehicles, engineering vehicles and other water systems for the personnel accompanying the vehicles;(d) water supply system for various ships and yachts. Equipped with matching filters, water can be taken directly from the sea, rivers, lakes, ponds, Wells. 2 - Food and beverage processing and processing equipment to achieve fluid food transfer, distribution, filling, etc. 3 - Domestic water supply. 4 - Solar energy industry. 5 - Other equipment and systems requiring fluid transfer and ejection. For example, cleaning equipment, road construction equipment, purification equipment, cooling systems, etc.

Minimum Order: 1 bags

2 cy series of high-pressure gear oil pump is suitable for the transportation of fuel oil, diesel oil, machine oil, and other similar liquid. The liquids do not contain particles or fiber, and temperature is not higher than 200 ℃, the viscosity is not more than 1500 CST. The pump can be used as a transport, pressure, fuel injection, hydraulic and lubrication pump, stainless steel gear pump is suitable for conveying corrosive liquids without solid. Application It can be used as transmission and booster pump in oil transportation system. In the fuel system can be used as delivery, pressure, injection fuel pumps. A hydraulic pump used in hydraulic systems to provide hydraulic power. It can be used as lubricating oil pump in all industrial fields. Structure features: The 2CY series gear oil pump is composed of pump body, pump cover, gear, bearing sleeve and shaft end seal. The gears are nitride treated and have high hardness and wear resistance. All moving parts in the pump are lubricated by the medium they are conveying. The four bearing sleeves in the pump are installed in the pump body, and the end clearance is automatically adjusted with the working pressure, so the pressure of the pump is stable, the output flow pulsation is small, and the volume ratio is high. 2CY series gear oil pump is simple and compact in structure, easy to use and maintain, highly adaptable and efficient. 2YC series gear pump pressure is higher than other gear pumps. It is suitable for conveying pressure requirements up to 2.5MPA liquid.

Minimum Order: 1 bags

PF plastic chemical pump： PF pump body, pump cover, impeller of plastic chemical pump(the wet parts which contact with liquids)are made of polyvinylidene fluoride or reinforced polypropylene by molding or injection processing. Polyvinylidene fluoride (PVDF) plastics have high mechanical strength and good corrosion resistance. PF chemical pump can convey the acid at the temperature from - 50 ℃ to 80 ℃ with various concentration of sulfuric acid, hydrochloric acid, nitric acid, acetic acid, phosphoric acid, chromic acid, oxalic acid, hydrofluoric acid and alkali, chemical medium, such as organic solvents, oxidant, alkali, chemical etc. in fertilizer, dyestuff, reagent, pesticide, pharmaceutical, electroplating, environmental protection and other industrial departments to transport corrosive medium without particles as the energy-saving pump. PF series chemical pumps have direct connection structure, which is connected by the pump body and bracket with the motor flange, the bracket supports the pump body, and the impeller is directly connected with the motor through the shaft. The pumps have simple and compact structure, few parts, good performance. The rotation direction of the pump is for clockwise rotation from suction inlet to the motor, the pump outlet is vertical upward. Pump seal adopts PTFE (F4) bellows mechanical seal with corrosion resistant. The chemical pump can be made with self priming performance and the suction height is up 4m.

Minimum Order: 1 bags

CQF engineering plastic magnetic pump is the application of modern magnetics principles. The working principle of magnetic couplings is used into the centrifugal pump as the magnetic pump. Magnetic pump is with static seal instead of dynamic seal so as to make the flow components of pump be in a completely sealed state, further to completely solve the problem of leakage from mechanical seal. CQF engineering plastic magnetic pump is made of reinforced polypropylene engineering plastic (with corrosion resistance, high strength), steel ceramics, stainless steel etc. materials, so it has a good corrosion resistance and can make the transport medium away from pollution. CQF engineering plastic Magnetic pump has compact structure, beautiful appearance, small volume, low noise, reliable operation, easy to use and maintain. It can be widely used in chemical, pharmaceutical, petroleum, electroplating, food, national defense, scientific research institutions, metallurgy, dye and other units. CQF engineering plastic magnetic pump is widely used to convey acid, alkali, oil etc. rare and precious liquid, venom, volatile liquid, as well as circulating water equipment, filter equipment. CQF magnetic pump is especially suitable for the liquids which is easy to leak, flammable, explosive etc. transportation. The pump driven by the explosion-proof motor is more ideal equipment. (pump material: reinforced polypropylene) Model meaning: CQF type engineering plastic magnetic pump CQF 50-25 50- inlet diameter (mm) CQF- engineering plastic magnetic drive pump 25 - head (m)

Minimum Order: 1 bags

ZYB hard tooth surface waste oil gear pump ZYB waste oil gear pump adopts self - sealing lubrication, clearance automatic adjustment structure. The flow parts are made of high wear - resistant materials. It has the characteristics of compact structure, good self-priming, high efficiency and strong adaptability, etc. In the occasions of conveying liquid containing impurities, the working life of the pump is 2-10 times longer than the general gear pump. ZYB booster gear oil pump is designed for the interchangeability with KCB series common gear pumps. And the appearance and installation size and technical parameters are exactly the same as KCB series gear pumps. Therefore, ZYB slag oil pump is also known as KCB series "strong type", which shows the important characteristics of long life and stable pressure of the pump when conveying medium with lubrication and no impurities. ZYB waste oil gear pump is suitable for conveying medium with less impurities and less lubrication in heavy oil, diesel oil, coal tar, grain oil, chemical industry, building materials, daily chemical products and other industries. Liquids temperature is no higher than 200°C and liquids viscosity is no higher than 150mm2/S containing non-metallic impurities. ZYB booster oil pump is especially suitable for stable working pressure, long-term continuous working occasions. For example: the strong lubrication system, the fuel transfer and injection in the fuel burning system. ZYB waste oil transfer pump is not suitable for conveying corrosive, containing metal impurities, sand and stone impurities with particle diameter greater than 3mm and medium with high volatility and low flash point Such as: gasoline, benzene, etc.

Minimum Order: 1 bags

DF horizontal stainless steel multistage chemical pump DF horizontal multistage pump is made of stainless steel material and is used to transport the corrosive liquids with temperature of -20 to 150℃, without solid particles. The inlet pressure of the pump is less than 0.6mpa. DF multistage pump is horizontal, single suction, multi - stage centrifugal pump. The outlet and inlet of the pump are vertically upward, and the suction section, middle section and spit section of the pump are connected together with tension bolts. Pump rotor is installed in the shaft of the impeller, balance plate and other parts. Both ends of the rotor are supported by rolling bearings or sliding bearings which are lubricated by grease. The axial forces of the rotor are balanced by the balancing disc. Features: Shaft seal can be for mechanical seal or packing seal. There is seal box in the both end of shaft seal. Mechanical seal or packing seal can be stalled inside of seal box. Water with the certain pressure is filled into the seal box for the water seal and cooling. A replaceable sleeve is provided at the shaft seal to protect the pump shaft. The pump is directly driven by the electric motor through an elastic shaft coupling. Viewed from the motor direction, the pump has clockwise rotation. Performance range: Flow range (Q) : 6-330m /h Head range (H) : 100-900m Ambient temperature (℃) : ≤40℃ Medium temperature (℃) : -20℃~105℃ Speed (r/min) : 1450-2900r/min

Minimum Order: 1 bags

BQW explosion-proof mine submersible sewage drainage pump BQW explosion-proof submersible sewage pump is designed and manufactured in accordance with the flameproof standard. In the motor part, strict flameproof measures are adopted. The motor housing is made of cast steel, the rotor shaft is made of stainless steel. The unit can drain the shallow water on the surface of the working face and also work under the water for a long time. Electric pump is with compact structure, light and small easy to move, without water diversion, double-sided seal, durable, safe and reliable, strong adaptability and other advantages. BQW explosion-proof submersible sewage pump is an advanced and reliable drainage tool used in mining, roadway, bottom hole water hole, local water hole, drainage of coal preparation factory, engineering drainage and other occasions. It is suitable for underground roadway and mining area of coal mine, underground water discharged from other working medium containing methane or explosive gas mixture of coal dust and coal water containing suspended coal powder, and also suitable for explosive environment of petrochemical system. 1 - Three-phase, AC, 50Hz / 380V or 660V (allowable deviation ±5%). 2 - The submerged depth of the submersible sewage pump shall not exceed 5m. 3 - The temperature of the conveying medium shall not exceed 40℃. 4 - The value of the pumped liquid is 6.5-10. 5 - The volume of solid impurities in sewage is generally less than 2%. 6 - The altitude shall not exceed 1000 meters. conveyed medium 1 - Groundwater containing methane or coal dust explosive gas mixture and coal water containing suspended coal powder. 2 - Sewage and general groundwater in explosive environment of petrochemical system. The motor used The motor is completely closed, mine flameproof type three - phase submerged sewage pump motor Enclosure protection form: IP68 Standard voltage (50Hz) : three-phase 380V or 660V Enclosure mark: flameproof mark "ExdIIBT4”

Minimum Order: 1 bags

2BV water ring vacuum pump: 2BV water ring vacuum pump is suitable to pump gas and water vapor with suction pressure up to 33mbar absolute pressure (97% vacuum). When using transformer oil as the working fluid (called the oil ring vacuum pump), the suction pressure can reach 6.7mbar absolute pressure (99.3% vacuum), which can completely replace the reciprocating vacuum pump. When the liquid ring vacuum pump works for a long time under the suction pressure approaching the limit vacuum, the cavitation protection tube should be connected to protect the pump and eliminate the cavitation sound. When it is used as a compressor, the maximum pressure is 0.26mpa (absolute pressure). When used as a compressor, 2BV pump power will increase with the increase of exhaust pressure. Please indicate the exhaust pressure to select the appropriate motor power when ordering. As a new generation of energy-saving products, 2BV water ring vacuum pump will completely replace SK, 2SK series water ring vacuum pump and W, WY, WL series reciprocating vacuum pump with excellent performance and many advantages. 2BV2-EX, 2BV6 series water-ring vacuum pumps/compressors are mainly used to pump the explosive gas and work in various flammable and explosive environments, with the same performance parameters as the corresponding models of 2BV2, 2BV5 series. 2BV series stainless steel vacuum pumps can be used in a variety of occasions where corrosion resistance is high and cleanliness is high. SUS304 (0Cr18Ni9), SUS316 (0Cr17Ni12Mo2), SUS316L (00Cr17Ni14Mo2) and other stainless steel materials can be used for all the overflow components of 2BV series stainless steel vacuum pump under working conditions. The pump shaft material is 2Cr13 or 0Cr18Ni12Mo2Ti 2BV type water ring vacuum pump mechanical seal USES the import product, the seal can use the fluorine rubber or the polytetrafluoroethylene. Compared with domestic water ring vacuum pumps of the same type such as SK, 2SK and SZ, it has the following characteristics: 2BV water ring vacuum pump is with coaxial direct connection design and saves space and it is easy to install. 2BV water ring vacuum pumps all adopt imported mechanical seals as standard configuration. all the 2BV water ring vacuum pumps are equipped with cavitation protection tube interfaces. If working under the ultimate pressure, opening the cavitation protection tube interface (or connecting with the separator) can eliminate cavitation sound and protect the pump under the condition of ensuring the suction effect to the maximum extent. aluminum bronze impeller has high strength and durability and has improved the corrosion resistance of 2BV water ring vacuum pump. If the flow components using stainless steel material can work in a more demanding environment. a unique flexible vent design that does not produce over-compression ensures the best efficiency of the 2BV water ring vacuum pump within its performance range. all use Y2 series motors with IP54 and IP55 protection grades (generally IP44) ·2BV water ring vacuum pumps all adopt NTN or NSK imported bearings

Minimum Order: 1 bags

CPN corrosion resistant alkali liquids transfer pump is used to convey alkali liquids containing solid particles and other liquids which is easy t crystalize. CPN alkali liquid transfer pump is widely for chlor-alkali, soda industry, medicine, chemical fertilizer, pesticide industry, petroleum, chemical industry, chemical fiber, paper industry, dye industry, environmental protection engineering and water treatment system etc. For the liquids with high temperature, the pump equipped with cooling water device can be sed. CPN alkali liquids transfer pump has the high efficiency, low energy consumption, strong corrosion resistance and not clogging etc. features. Pump rotation direction: Viewed the pump from the driving end, it is for clockwise. In the inspection of the disassembled impeller and shaft seal, CPN alkali liquids transfer pump has this kind of back door structure and need not disassemble the pipeline and electric motor. The maintenance is simple and convenient. 1 - Pump body is supported by cast foot to bear any load from the pipeline and so as to ensure the service life of the bearing and mechanical seal. 2 - The pump shaft with high rigidity is precisely machined and the bearing is lubricated with thin oil, and the oil level of the bearing body is measured by the oil ruler, which is reliable, practical and easy to operate. Pump design with axial clearance adjustment mechanism can reduce the impact of wear on pump performance. 3, Open impeller is not easy to be blocked. 4 - Packing seal and single or double mechanical seal can be chosen. There are internal and external mounting and balance, non - balance structure. 5 - Y-type ordinary motor or YB type explosion-proof motor shall be used as the power driving. Flow(Q)1.6 to 400m3/h 　　 Head (H)5 to 125m Working pressure：P≤1.6MPa 　　 Working temperature：20 to 150℃

Minimum Order: 1 bags

YHCB double circular arc gears pump YHCB circular arc gear pump is compared with other gear pump. YHCB circular arc gear pump has the large flow. YHCB circular arc gear pump is mainly used for conveying various liquids with viscosity in 5-1500 CST and the temperature not higher than 80℃. And the liquids do not contain any solid particles and has not corrosion. The pump is widely used to convey oils such as extracted gasoline, kerosene, diesel oil and machine lubricating oil. It is the ideal pump for the oil tank vehicle modification industry and the oil sector. YHCB gear pump with double circular arc structure is a new pump developed at the base of the oil pump. YHCB oil pump is the high efficiency and energy saving special gear pump, with large flow, high pressure, small volume, low noise, low input speed, strong self- absorption, easy installation and maintenance and other advantages. YHCB circular arc gear pump can be installed in the car, with the help of the car gearbox to drive the output shaft. The bronze gear or stainless steel gear and explosion proof motor can be chosen for the explosion proof requirements.

Minimum Order: 1 bags

IN series jacketed stainless steel heat preservation pump, steam heat preservation pump, corrosion resistance and crystallization resistance chemical pump IN Series new fused/melt urea pump is a single stage single suction Cantilever centrifugal pump. The pump is Suitable for conveying melting urea liquid in chemical fertilizer plant and other corrosive liquid without suspended particulate matter. The temperature of the medium is allowed -20~180 degrees Celsius. The pump is horizontal suction, radial top spit out and the front side of the pump has a heat preservation jacket, double jackets can allow 0.59mpa and 170 degrees Celsius steam insulation. Users can choose different materials according to the degree of corrosion performance of the medium, models and different flow head can be regulated. Parameter range Flow: 2-400 m3 / h Head: 3-125 m Speed: 2900 r/min/1450rpm

Minimum Order: 1 bags

FYB Stainless steel corrosion resistant submerged pump FYB type corrosion resistant vertical submerged pump is a single-stage single suction long shaft type submerged centrifugal pump. The rated performance point and flange connection size of FYB submerged pump are equivalent to ISO2858 international standard and the technical conditions are ISO5199 standard. Compared with the original FY corrosion resistant submerged pump, it has the advantages of small volume, high efficiency, good energy saving effect and reliable operation. FYB corrosion resistant submerged pump is Suitable for conveying corrosive media containing solid particles and abrasive matter The conveying temperature of the pump is generally 0~105℃. When the temperature is -20~0℃, 105~180℃, the heat preservation jacket and cooling jacket can be used. If there is a small number of solid particles in the conveying medium, the sliding bearing shall be externally lubricated (with water and other allowable media with external pressure greater than 0.2MPa), in the case the user shall specify them. The working pressure of the pump is designed according to 1.6MPa. Performance range of pump: flow 1.6-2600m3/h, head 5-132m. Structure of FY corrosion resistant submerged pump FYB type corrosion resistant submerged pump is mainly composed of pump body, pump cover, impeller, shaft, elastic coupling, pipe flange, guide bearing, intermediate connection, upper and lower liquid pipe, bearing bracket, bottom plate and other parts. The suction inlet of the pump is along the axis and the outlet is parallel to the axis. The pump's rotary direction. Viewed pump inlet to the motor end, the pump is clockwise. FYB type corrosion submerged pump of vertical motor with double bolt tightening up on the motor seat, and through the elastic coupling with the pump rotation directly, pump body take over middle, bracket, fluid pipe, flange, with bolt connection constitute an organic whole, fixed on the market, overall pump through the backplane is installed on the container. The wet parts are made of stainless steel material and non wet parts such as motor frame and bearing bracket etc. are made of cast iron.

Minimum Order: 1 bags