Pumps

CPN corrosion resistant alkali liquids transfer pump is used to convey alkali liquids containing solid particles and other liquids which is easy t crystalize. CPN alkali liquid transfer pump is widely for chlor-alkali, soda industry, medicine, chemical fertilizer, pesticide industry, petroleum, chemical industry, chemical fiber, paper industry, dye industry, environmental protection engineering and water treatment system etc. For the liquids with high temperature, the pump equipped with cooling water device can be sed. CPN alkali liquids transfer pump has the high efficiency, low energy consumption, strong corrosion resistance and not clogging etc. features. Pump rotation direction: Viewed the pump from the driving end, it is for clockwise. In the inspection of the disassembled impeller and shaft seal, CPN alkali liquids transfer pump has this kind of back door structure and need not disassemble the pipeline and electric motor. The maintenance is simple and convenient. 1 - Pump body is supported by cast foot to bear any load from the pipeline and so as to ensure the service life of the bearing and mechanical seal. 2 - The pump shaft with high rigidity is precisely machined and the bearing is lubricated with thin oil, and the oil level of the bearing body is measured by the oil ruler, which is reliable, practical and easy to operate. Pump design with axial clearance adjustment mechanism can reduce the impact of wear on pump performance. 3, Open impeller is not easy to be blocked. 4 - Packing seal and single or double mechanical seal can be chosen. There are internal and external mounting and balance, non - balance structure. 5 - Y-type ordinary motor or YB type explosion-proof motor shall be used as the power driving. Flow(Q)1.6 to 400m3/h 　　 Head (H)5 to 125m Working pressure：P≤1.6MPa 　　 Working temperature：20 to 150℃

Minimum Order: 1 bags

YHCB double circular arc gears pump YHCB circular arc gear pump is compared with other gear pump. YHCB circular arc gear pump has the large flow. YHCB circular arc gear pump is mainly used for conveying various liquids with viscosity in 5-1500 CST and the temperature not higher than 80℃. And the liquids do not contain any solid particles and has not corrosion. The pump is widely used to convey oils such as extracted gasoline, kerosene, diesel oil and machine lubricating oil. It is the ideal pump for the oil tank vehicle modification industry and the oil sector. YHCB gear pump with double circular arc structure is a new pump developed at the base of the oil pump. YHCB oil pump is the high efficiency and energy saving special gear pump, with large flow, high pressure, small volume, low noise, low input speed, strong self- absorption, easy installation and maintenance and other advantages. YHCB circular arc gear pump can be installed in the car, with the help of the car gearbox to drive the output shaft. The bronze gear or stainless steel gear and explosion proof motor can be chosen for the explosion proof requirements.

Minimum Order: 1 bags

IN series jacketed stainless steel heat preservation pump, steam heat preservation pump, corrosion resistance and crystallization resistance chemical pump IN Series new fused/melt urea pump is a single stage single suction Cantilever centrifugal pump. The pump is Suitable for conveying melting urea liquid in chemical fertilizer plant and other corrosive liquid without suspended particulate matter. The temperature of the medium is allowed -20~180 degrees Celsius. The pump is horizontal suction, radial top spit out and the front side of the pump has a heat preservation jacket, double jackets can allow 0.59mpa and 170 degrees Celsius steam insulation. Users can choose different materials according to the degree of corrosion performance of the medium, models and different flow head can be regulated. Parameter range Flow: 2-400 m3 / h Head: 3-125 m Speed: 2900 r/min/1450rpm

Minimum Order: 1 bags

FYB Stainless steel corrosion resistant submerged pump FYB type corrosion resistant vertical submerged pump is a single-stage single suction long shaft type submerged centrifugal pump. The rated performance point and flange connection size of FYB submerged pump are equivalent to ISO2858 international standard and the technical conditions are ISO5199 standard. Compared with the original FY corrosion resistant submerged pump, it has the advantages of small volume, high efficiency, good energy saving effect and reliable operation. FYB corrosion resistant submerged pump is Suitable for conveying corrosive media containing solid particles and abrasive matter The conveying temperature of the pump is generally 0~105℃. When the temperature is -20~0℃, 105~180℃, the heat preservation jacket and cooling jacket can be used. If there is a small number of solid particles in the conveying medium, the sliding bearing shall be externally lubricated (with water and other allowable media with external pressure greater than 0.2MPa), in the case the user shall specify them. The working pressure of the pump is designed according to 1.6MPa. Performance range of pump: flow 1.6-2600m3/h, head 5-132m. Structure of FY corrosion resistant submerged pump FYB type corrosion resistant submerged pump is mainly composed of pump body, pump cover, impeller, shaft, elastic coupling, pipe flange, guide bearing, intermediate connection, upper and lower liquid pipe, bearing bracket, bottom plate and other parts. The suction inlet of the pump is along the axis and the outlet is parallel to the axis. The pump's rotary direction. Viewed pump inlet to the motor end, the pump is clockwise. FYB type corrosion submerged pump of vertical motor with double bolt tightening up on the motor seat, and through the elastic coupling with the pump rotation directly, pump body take over middle, bracket, fluid pipe, flange, with bolt connection constitute an organic whole, fixed on the market, overall pump through the backplane is installed on the container. The wet parts are made of stainless steel material and non wet parts such as motor frame and bearing bracket etc. are made of cast iron.

Minimum Order: 1 bags

FBZ Stainless steel corrosion resistant self priming centrifugal pump is made of stainless steel material. The impeller of FBZ self priming pump can be open impeller or closed impeller. The connection between the pump and motor can be shaft coupling with bearing bracket and closed coupling (direct connection). The shaft seal is cantilever type mechanical seal. FBZ Stainless steel self priming centrifugal pump has reliable corrosion resistance, easy maintenance, compact structure, low energy consumption, good sealing performance etc. advantages. Application: FBZ Stainless steel corrosion resistant self priming centrifugal pump is used to convey the corrosive liquid with small soft particles or fiber and other sanitary liquids. The pumped liquids temperature is not higher than 90DegC for the pump directly connected with motor. The pump with shaft coupling can handle the liquids not higher than 105DegC. FBZ Stainless steel corrosion resistant pump has the self priming performance. Suction height is up 5meters. FBZ Stainless steel corrosion resistant self priming centrifugal pump is widely used in food, beverage, medicine, sewage treatment, chemical industry, electroplating, bleaching and other industries.

Minimum Order: 1 bags

JXF Fluoroplastic liner axial flow The flow parts of the pump are made of PFA material with high quality. JXF fluoroplastic liner axial flow is highly adaptable to corrosive liquids such as nitric acid, sulfuric acid, hydrochloric acid, phosphoric acid and strong oxidizer. The pump has the good corrosion resistant for the corrosive liquids. Its corrosion resistance is far better than high nickel alloy, no. 20 alloy, even more than high silicon cast iron etc. Excellent wear resistance The pump adopts a special process of drying and pressing, in which the thickness of fluorine lining of the steel lined compound pump body is more than 10mm, the thickness of fluorine of the splint pump body is more than 25mm. And the special treatment is carried out on the inner wall of fluorine, the resistance to ferrous sulfate abrasion is the first in the world. Excellent high temperature resistance Because the pump has excellent thermal property, self-lubrication and impact resistance, the impeller and other key parts of fluoroplastics will not be cracked due to impact, making up for the ceramic pump, high silicon cast iron pump fragile defects. The performance of the whole machine is excellent, smooth operation and in the -30 to 150 DegC harsh environment the pump can be safely used for a long time. (the maximum temperature for waste acid concentration is 130DegC, while the melting point of fluorine material is 360DegC) Easy to disassemble and easy to repair Because the impeller, pump cover, shaft sleeve are all made of fluorine material, the weight of the pump is greatly reduced, the rotor part can be easily and conveniently removed from the pump body, so the dismantling, unloading, loading can be easily completed. Avoid silicon iron pump need to be carefully repaired and afraid of being broken. To sum up, this pump is the most ideal and suitable special pump for the concentration of waste acid in titanium dioxide. JXF splint type axial flow pump structure features 1 - The pump is designed according to the optimal flow conditions according to the required parameters of the axial flow pump. 2 - This pump adopts a pull-out structure pump with rear door, which is convenient for disassembly and maintenance. The connection pipe can be removed without disassembly during maintenance. 3 - The shaft seal adopts the new combined seal, which is suitable for conveying the highly corrosive liquid containing suspended particles. 4 - The flow passage of the pump body is not easily blocked, with large cavitation allowance and high reliability of shaft and bearing design to ensure smooth operation, small vibration, low noise and long service life. 5 - The rotation direction of the pump shall be marked with arrows on the bearing bracket. Fluorine-lined axial flow pump structure This series of pump is cantilever structure, horizontal installation can also be according to the user needs to adopt belt wheel drive, adjust the flow and head. JXF type fluorine-lined axial pump mechanical seal The mechanical seal adopts double-end seal, the stationary ring and dynamic ring adopt imported haste alloy material, which must be rinsed with cooling water or use external single-face mechanical seal.

Minimum Order: 1 bags

JYWQ submersible sewage pump is with automatic agitating device. The pump can stir the sediment into the wastewater and discharge them. JYWQ, JPWQ series automatic agitating sewage pump is on the basis of conventional sewage pump and adopts automatic agitating device. When sewage pump works with the motor shaft rotation and generate strong stirring force to make the sediment be mixed into suspended solids in the sewage pool and finally the wastewater with the solids is discharged outside of the pump. JYWQ, JPWQ submersible sewage pump improves the performance of anti-clogging and sewage drainage capacity. The pump can complete a one-time drainage, sewage disposal, in addition to the deposition so as to save operating costs. So the pump has obvious advancement and practicability of the environmental protection product. JPWQ automatic agitating sewage pump 1 - Discharge of serious polluted wastewater from factories and businesses. 2 - Drainage system of urban sewage treatment plants, hospitals and hotels. 3 - Sewage drainage station in residential area. 4 - Water supply device of civil air defense system drainage station and waterworks. Municipal engineering, construction site. 6, exploration, mining, power plant supporting machine. 7, rural digester, farmland irrigation, dredging river pond. JPWQ automatic agitating sewage pump structure characteristics 1 - Adopt the unique double-channel non-clogging impeller structure to improve the flow capacity and sewage discharge capacity. 2, automatic stirring device, produce a strong stirring force, the pool of sediment stirred into suspended matter inhalation impeller discharge, to achieve the role of dredging. 3 - The baffle divides the base into two parts, stirring and water will not affect each other. 4, the mechanical seal for double-sided mechanical seal, long-term in the oil chamber, to ensure the safe and reliable operation of the pump. 5 - The fluid power seal of the auxiliary impeller structure has the function of auxiliary seal, so as to protect the mechanical seal, balance the axial force and extend the service life of the bearing. 6 - The pump wiring cavity is equipped with a leakage detection probe. In case of leakage, the probe will send a signal and the control system will protect the pump. 7 - The stator of the motor is insulated with grade B and grade F, and has built-in heat protector. When the motor is overloaded and generates heat, the protector will act in time to protect the pump and motor absolutely. 8 - An oil-water probe is installed in the oil chamber. When the mechanical seal is damaged, the water enters the oil chamber, the probe sends a signal, and the control system protects the pump. 9 - JPWQ pump with the circulating cooling system can ensure the normal water level of the pump in the water tanks.

Minimum Order: 1 bags

BA Series centrifugal pump is a single-stage, single-suction cantilever type centrifugal pump, which is used to pump clean water and liquids with physical and chemical properties similar to water. The highest temperature of the pumped liquid should not exceed 80 degree Celsius. BA Series single stage single suction cantilever centrifugal pump is suitable for factories, mines, urban water supply and rural irrigation. Pump overview BA type pump is single-stage single-suction cantilever type clean water centrifugal pump and has the advantages of small appearance, light weight, simple structure, easy installation and etc. BA single stage single suction centrifugal pumpcan be used to transport clean water and other liquids in physical and chemical properties similar to water. It can be used with ZS vacuum jet pump. Scope of use: It is suitable for industrial and urban water supply and drainage, high-rise building supercharging water supply, garden sprinkling irrigation, fire supercharging, long-distance transportation, HVAC refrigeration system circulation, bathroom and other cooling and heating water circulating pressure increase/booster etc equipments. The pumped liquids temperature is not higher than 80 degree Celsius. Application: metallurgy, chemical industry, textile, papermaking, hotel and other boiler hot water pressurized circulation transportation and urban heating system, hot water type operating temperature is not higher than 120 degree Celsius. Performance range: Head: 8 to 93 meters, the flow rate is 4.5 to 360 meters 3 / hour, the liquid temperature shall not exceed 80 degree Celsius (Normal temperature pump), suitable for factories, mines, urban water supply and farmland irrigation, booster.

Minimum Order: 1 bags

I-1B thick slurry pump is a power equipment used for conveying. This device is a single screw volumetric rotary pump, which utilizes the rotation of an eccentric single screw in a double screw liner to move the concentrated slurry along the spiral groove from the suction port to the discharge port, achieving the pump's conveying function. Features 1. It can transport high concentration, high viscosity<10000 PaS and suspended slurry containing particles. 2. The conveying fluid flow is stable, without overcurrent, pulsation, stirring, or shearing of the slurry. 3. The discharge pressure is independent of the rotational speed, and high discharge pressure can be maintained even at low flow rates. 4. The flow rate is proportional to the speed, and flow regulation can be achieved through a variable speed mechanism or a speed regulating motor. 5. Strong self-priming ability, can directly suck liquid without the need for a bottom valve. 6. The pump can be reversed, and the liquid flow direction is changed by the rotation direction of the pump, which is suitable for situations where the pipeline needs to be flushed in the reverse direction. 7. Smooth operation, low vibration and noise. 8. Simple structure, easy disassembly and maintenance. This pump is widely used in chemical, pharmaceutical, brewing, papermaking, food and other units. Structure: I-1BB type: Shell casting, transmission components (main shaft, screw, and winding shaft) made of 2Cr13 stainless steel, suitable for conveying general neutral and concentrated slurry, as well as general slightly acidic and alkaline slurry. I-1BF type: The transmission components and pump casing in contact with the slurry are both made of stainless steel, suitable for conveying food, pharmaceutical, and corrosive slurry. Rubber bushings are available in general wear-resistant rubber, food grade rubber, and oil resistant rubber for users to choose from. The transmission methods include direct transmission between the motor and the pump shaft, direct transmission between the motor and the pump through a reducer, and transmission between the motor and the pump shaft through a V-belt pulley. There are generally enclosed, explosion-proof, and electromagnetic speed regulating motors available for use with electric motors, as well as continuously variable transmissions and gear reducers for users to choose from them.

Minimum Order: 1 bags

CWX marine horizontal self priming centrifugal vortex pump CWX horizontal self priming centrifugal vortex pump is applicable to transport seawater and fresh water for drinks, washing and sanitary with the temperature no higher than 85 degree C. When the impeller of CWX Marine self-priming vortex pump rotates, centrifugal force is generated. Under the action of this centrifugal force, the liquid flows into the blade root from the side face of the pump shell and is thrown outward to the groove of the cover plate on both sides. This part of liquid originally moves in a circle with the blade and has a certain velocity energy. In the groove of the cover plate, velocity energy changes into pressure energy. And then it's grabbed by the leaf. In the process of the liquid particle from the inlet to the outlet, such action is repeated many times, and the energy increases successively, just like the liquid in the centrifugal pump by the multi-stage impeller action. Liquid in the channel along with the star impeller movement, to the cut-off point, because the channel is suddenly blocked, liquid from the outlet hole out. The exit hole is set on the exit cover plate, and the entrance hole is set on the entrance cover plate, which is opened in the place where the groove suddenly appears behind the cut-off area, where the negative pressure is obviously to absorb the liquid. CWX Marine self-priming vortex pump performance characteristics (1) the characteristics of small volume and light weight of vortex pump have great advantages in Marine installations. (2) having self-priming ability or realizing self-priming by means of simple devices. (3) the head characteristic curve has a steep drop, so it is not sensitive to the pressure fluctuation in the system. (4) some vortex pumps can realize the mixture of vapor and liquid. This is of great significance for pumping volatile liquid containing gas and high temperature liquid with high vaporization pressure. (5) vortex pump structure is simple, casting and processing technology are easy to achieve, some vortex pump parts can also use non-metallic materials, such as plastic, nylon molded impeller.

Minimum Order: 1 bags

TRP Stainless steel lobe rotor pump: TRP Series stainless steel sanitary rotor lobe pump can be named colloidal pump. It has more special function than normal rotor pumps. The TRP Series stainless steel sanitary pump is specially suitable for high viscosity jelly. The pumped materials will not be changed after the delivery. All wet parts of TRP Series sanitary rotor lobe pump are made of stainless steel and the pump is used to pump the fluids with high viscosity or thickness or with solids. Liquids temperature range: -30 to 200 Degree Celsius. High pressure of outlet makes sure the long distance and high resistance transportation with stable capacity. There is no touch of two rotors. So no abrasion even after long time work. It has the merits of stable work, low noise and easy assembly and disassembly. The pump is widely used in health, food, chemical industry areas etc.

Minimum Order: 1 bags

PWDDFL multi-suction sewage pump adopts single (double)flow channel and single (double)blades structure for not clogging and no leakage. The pump has compact structure, small volume, smooth operation and little vibration, high efficiency and easy installation and operation. PWDDF multi-suction sewage pump is widely used to transfer the wastewater or waste liquids with solid particles. Features: 1 - Multiple suction heads: each pump has 4 suction heads which are distributed in the center and corner of pump. 2 - With stirring (agitator device): A agitator is installed at the lower part of the main suction head and it can stir up the sediment in the pump pit and effectively prevent the suction head from being blocked. 3 - With metal reamer. The metal reamer is installed on the upper part of the mixing wheel which can used to grind the fiber materials in sewage such as gloves, rags and plastics etc and effectively preventing the water suction head from being blocked. 4 - The pump does not need to be fixed. The main suction head is as suction head and the frame of the pump. Just put the pump in the pump pit to join the outlet pipe. PWDDFL Vertical multi-suction sewage pump is composed of vertical motor and pump body. The pump is for double suction centrifugal impurity pump and impeller is open type. The flow parts can be cast iron, cast steel or stainless steel etc material.

Minimum Order: 1 bags

HTB-ZX-U Series anti-corrosion engineering plastic self-priming pump is horizontal single-stage single-suction cantilever self-priming pump. The pump adopts vacuum pump principle to have the self priming performance. The flow parts for the pumps are made of steel lined ultra-high molecular weight polyethylene (uhmwpe) with excellent corrosion resistance and abrasion resistance. The pump is suitable to pump clear liquid or corrosive medium containing a small number of particles. Compared with other self-priming pumps, this pump has the following significant advantages: This pump adopts vacuum pump principle to complete the process of self- priming with excellent self-priming performance. The pump does not need to be equipped with cushion valve and air control valve and there is no traditional self-priming pump backflow hole. Therefore, it will not happen because backflow hole is clogging for self-priming performance. The pump adopts horizontal cantilever back pull structure. Pump body is composed of liquid storage chamber, vortex chamber, air and water separation chamber for three parts. The pump has a novel structure, compact, beautiful and generous, convenient maintenance, reliable operation, strong and durable characteristics. The pump is equipped with Y4 type of hard to hard mechanical seal. The seal is not only more reliable, longer service life and because it uses the closed cooling structure of the assembly, the seal will not produce acid fog to further protect the environment. The pump is especially suitable to pump the corrosive medium with particles. The pump can be equipped with liquid level control device to achieve automatic control for convenient operation.

Minimum Order: 1 bags

FB and AFB stainless steel corrosion resistant centrifugal pump FB stainless steel corrosion resistant pump is suitable for the corrosive liquids without solid particle and the liquid temperature is from -20 to 120 degree Celsius, inlet pressure is not more than 2kg per cm2 - AFB stainless steel corrosion resistant centrifugal pump is improved on the base of FB corrosion resistant pump. AFB Stainless steel corrosion resistant pump adopts new auxiliary impeller and shaft sealing device. AFB stainless steel pump has the advanced hydraulic model, novel structure and high strength combination double end face mechanical seal, which has the advantages of high energy saving, compact structure, stable performance and reliable use. It is a single stage single suction cantilever corrosion resistant centrifugal pump. The pump and the delivery medium contact part of the flow parts, are made of 1Cr18Ni9Ti material(stainless steel). AFB Stainless steel corrosion resistant pump is used to convey the corrosive liquids without solid . The liquids temperature is from -20 to 120 degree Celsius. Pump inlet pressure is not more than 2kg per cm2 - When the pump is equipped with double end face seal and cooling device, the pump can transport the corrosive liquids with the temperature up 300 degree Celsius. FB and AFB stainless steel corrosion resistant centrifugal pump [FB and AFB stainless steel corrosion resistant centrifugal pump] technical parameters: Flow rate: 3.6 to 200m3/h; Head: 15 to 64m; Speed: 2900r/min; Power: 0.75 to 55KW; Inlet diameter: 25 to 150mm; Maximum working pressure: 2.0Mpa. FB and AFB stainless steel corrosion resistant centrifugal pump FB, AFB stainless steel corrosion resistant centrifugal pump is widely used in chemical industry, petroleum, metallurgy, light industry, synthetic fiber, environmental protection, food, medicine and other sectors. The pump uses double end face mechanical seal in order to improve product quality and reduce run, run, drip, leak and prevent pollution. It has the advantages of stable and reliable performance, good sealing performance, beautiful shape and convenient maintenance

Minimum Order: 1 bags