Testing Equipment

The GF3000 series stationary three phase electricity meter test bench is a fully automatic system that enables simultaneous, multi-position calibration and verification of three-phase electric energy meters error. FUNCTIONS: 1．Timing error test. 2．Creeping and starting test. 3．Equipped with RS232 communication port. 4．Calibration and verification of constant. 5．Standard deviation, 24 hour variation test.

Minimum Order: 1 bags

GF312V2 is mainly used to test the error of single-phase electricity meter,three-phase kWH meter and Various active and reactive energy meters. The the instrument adopted high-speed A/D conversion and sends it to DSP for digital processing,which greatly improves the accuracy and stability of measurement. Features: 1.accuracy: 0.02%,0.05%,0.1% 2.Portable design 3.Power recovery 4.Can measure two meters at the same time 5.Range: 0-600V; 0-120A 6.7 inch TFT color LCD 7.Three power supply modes 8.Harmonic: 2-51 9.Power consumption:≤13VA 10.Weight: 1.8kg

Minimum Order: 1 bags

The GF302D1 portable three-phase ELECTRICITY meter test device is a error measuring instrument. GF302D1 has high accuracy 0.05%, portable design and high tolerance about the environment. FEATURES: 1．range:voltage: 0-500V; current:0-120A; 2．Can store 500pcs of measurement data; 3．Weight: 12.8 4．Can measure frequency, harmonic wave,power factor; 5．With PC port,RS232 communication port 6．Can test by manual or automatic;

Minimum Order: 1 bags

This equipment is designed for cookware handle fatigue test, such as cooking pan, pots etc. During test, continuously raising and lowering a loaded item of cookware from a surface covered with a 5 mm thick rubber plate at the frequency of 25 times per minute. Total run 15,000 test cycles. Automatically stop when test cycles were up.

Minimum Order: 1 bags

This testing equipment is for the determination of resistance to chemical corrosion by boiling acids, boiling neutral liquids, and/or their vapors for the øat surface of vitreous and porcelain enamels. It includes two test zones of the liquid zone and vapor zone, the test specimen will be placed in these two zones and exposed to attack by specified chemical conditions for a required period. The tester is of the movable heating-controlling device for test solution heating and boiling, the solution-condenser circulation system can prevent solution loss and dry out at the process.

Minimum Order: 1 bags

This testing equipment is used for cookware base stability shock test in the cookware product. The test procedure is fully automatic, including heating, water pouring, evaporating, and repeating a total of 40 cycles. This tester equips the temp. & humid sensor, ensuring to read the correct date as per standard requests. When the test is finished, the customer can check the base and compare the result before and after 40 cycles of heating-pouring-evaporating, If the bottom of the cookware becomes no convex, then the test passes.

Minimum Order: 1 bags

GS-MEC-BS02Pro, fully automatic execution of the testing method after EN-12875-1 inclusive fully automatic dosage of the washing powder/river cleaner with the prescribed quantities. All rinsing and drying items as well as the test cycles are freely programmable.

Minimum Order: 1 bags

This test simulates the repeated application of loads and/or movement of components occurring during long-term use and assessing the strength of the mattress under such conditions and is a test is a procedure mainly intended to evaluate the change of the properties of the mattress caused by repeated loadings. The test stand enables both durability, hardness, bed edge tests according to EN 1957 through-loading device (Roll), hardness measuring device, and edge measuring device in one stop without the need for a rearrangement of a specimen.

Minimum Order: 1 bags

This porosity tester is used to measure the porosity of flexible cellular polyurethane. The test principle is to place the specimen in a cavity, and the equipment automatically applies continuous air pressure, then test how easy it is for the air to pass through the cellular structure of the foam. It is applied to the ASTM D3574 standard and is suitable for three levels of low, medium, and high porosity foam.

Minimum Order: 1 bags

This machine will be known as the indentation force deflection test of flexible cellular polyurethane material and the results as the IFD values. This test consists of measuring the force necessary to produce designated indentations in the foam product, for example, indentations at 25 and 65 % deflections.

Minimum Order: 1 bags

This equipment is our updated version, it is an all-in-one machine that can do both hardness test, fatigue test, and integrated test in accordance with the ASTM D3574, ISO 2439, IDO 3385 standards. Users can evaluate the properties changes of the foam material occurring in the long-term use.

Minimum Order: 1 bags

This machine is designed for the determination of the rebound elasticity of the foam materials applied in ASTM D3574, ISO 8307, JIS 6400. This instrument through a given diameter and the quality of steel ball in the specified height on free falling on the foam sample, calculate the spring back of the maximum height of steel ball and ball drop height ratio is the percentage of spring rate, expressed as a resilient rate of foam plastics can rebound resilience. This machine adopts a microprocessor to control, LCD display and can print test data.

Minimum Order: 1 bags

Standard:GB17761-2018 Clause 7.2.1,Clause 7.2.2 , Clause 7.2.4, ISO4210. Application: This tester is used for the detection of electric bicycle speed limit and pedal riding ability. According to the relevant requirements of GB17761-2018, GB3565-2005 and other standards, the safety performance and energy consumption of electric bicycles and other products are tested. The data can be stored and transmitted. The test parameters include deceleration, speed, time, distance, force, current, voltage, and so on. Operating conditions: 1,Test environment: -5 °C ~ 35 °C, wind speed <3m / s. 2,Test road: 1) Road pavement: concrete road pavement. 2) Road size: 3m (length) * 2m (width) * 20cm (thickness). 3) Friction coefficient between dry road surface and electric bicycle tire: minimum 0.5. 3,Cycling staff weight: total mass ≤ 75Kg. Parameters: 1,It can test the safety performance of electric bicycle according to the requirements of GB17761-2018, voltage collection range: 24V/36V/48V, 48V/60V/72V. 2,The electric bicycle braking performance test can be carried out in accordance with the requirements of GB3565-2005. 3,The driving mileage test can be carried out as required. 4,A variety of test methods to meet the vehicle speed measurement of the vehicle's static state. 5,The electric bicycle safety performance test can be carried out in accordance with the requirements of GB17761-2018. 6,Instrument accuracy: ±2% (provided in the response file to provide proof of the technical parameters (manufacturer color pages or manuals or product manuals)). 7,Measuring range: NO. Item Range 1 Speed 0.5～200.0km/h 2 Distance 0～20000m 3 Time 0～99999s 4 Force hand brake 0 ~ 200N 5 Current 0～100A 6 Voltage 0～200V (Provided materials (manufacturer color pages or instruction manuals or product manuals) that reflect this technical parameter are provided in the response file) 8,Test parameter resolution: NO. Item Resolution 1 Speed 0.01km/h 2 Distance 0.01m 3 Time 0.01s 4 Force 0.1N 5 Current 0.1A 6 Voltage 0.1V The main configuration: 1,1 set of professional version test software 2,Control display device 1 PC 3,GPS sensor 1 Set 4,Speed sensor 1 Set 5,Brake operating force component 1 Set 6,Current sensor 1 Set 7,Control computer 1 PC 8,Brake spray device 1 Set 9,Test accessory 1 Set 10,Import VBOX II SX (RLVB2SX) road vision 1 PC ISO4210 IEC Test Equipment Electric Bicycle Concrete Road Pavement 200V Tester With Friction Coefficient Of 0.5 0

Product Description ISO 16750-4 Auto Parts Test Equipment Splash Water And Submersion Test Chamber Standard: ISO16750-4 Road vehicles-Environmental conditions and testing for electrical and electronic equipment-Part 4: Climatic loads, clause 5.4.2 Ice water shock test. VW-80000 Electric And Electronic Components In Motor Vehicles up to 3.5t General Requirements, Test Conditions and Tests clause 9.12 K-12 Temperature Shock With Splash Water; GB/T 28046.4-2011 Auto Parts Test Equipment Purpose: This test simulates a thermal shock induced by ice water and applies to products in the splash areas of the vehicle. The purpose of this test is to simulate ice water splashing over a hot system/component. This happens when driving on wet roads during the winter. Failure modes are mechanical cracking of materials or seal failures caused by different temperature expansion coefficients. It is a reliability test equipment for various kinds of electronic, electrical, plastic and other raw materials and devices for cold resistance, heat resistance, ice water splash resistance test, ice water immersion resistance test and quality control engineering reliability test equipment. Test method: Splash water test: Heat the DUT in a hot air oven at T max for the specified holding time, t h . Then splash the DUT with ice water for 3 s. If the DUT is splashed in the vehicle from only one direction, splash it from this direction only while it is in an as-installed position. If the equipment is splashed from various directions in the vehicle, then these directions shall be taken into account. In this case, use a new DUT for each splash direction. The width of the splash directed at the DUT shall always be greater than the width of the DUT. If the DUTs to be splashed prove too big for one jet, arrange several jets in a row to produce a line of splash impact on the DUT. See Figures 4 to 6. Test parameters include: ⎯ number of cycles: 100; ⎯ holding time, t h , at T max : 1 h or until DUT temperature stabilization is reached; ⎯ transition duration: < 20 s (for manual transition of DUT between temperature storage and splashing); ⎯ test fluid: de-ionized water; ⎯ water temperature: 0 °C to +4 °C; ⎯ water flow: between 3 l and 4 l per 3 s (splash duration); ⎯ distance between jet and DUT surface: (325 ± 25) mm (water shall be applied over the complete width of the DUT); ⎯ operating modes: see Figure 5; ⎯ orientation of the DUT: as in the vehicle. Auto Parts Test Equipment Submersion test: Connect the DUT to the test equipment. Operate the DUT in a hot air oven at T max for the specified holding time, t h. With the device still operating, submerge it for 5 min in an ice water tank at least 10 mm deep. Test parameters include: ⎯ number of cycles: 10; ⎯ holding time, t h , at T max : 1 h or until DUT temperature stabilization is reached; ⎯ transition duration: < 20 s; ⎯ test fluid: de-ionized water; ⎯ water temperature: 0 °C to +4 °C; ⎯ immersion time: 5 min; ⎯ operating mode: 3.2 in accordance with ISO 16750-1; ⎯ orientation of the DUT: as in the vehicle. Parameter: Inner size 1000*1000*1000mm Outer size 1650*1800*2300mm Submersion area size 500*500*500mm Jet qty. 1 Jet position Right side of the inner chamber Distance between jet and DUT surface 325 ± 25 mm (Can be adjusted manually) Jet water flow 3-4L/3S Water temperature control range 0-+4°C Temperature range RT+10°C -150°C Cooling rate 25°C-2°C≤60min Heating rate RT+10°C -150°C≤45min Injection time per cycle (30min) 3S, interval time: 29m57s (touch screen setting) Cycle 100times (touch screen setting) ISO 16750-4 Auto Parts Test Equipment Splash Water And Submersion Test Chamber 0