Testing Equipment

Product Introduction: 1.Neware BTS5V12A battery testing equipment provides most applications in cylindrical cell and pouch cell capacity Testing.It based on charging discharging battery under different modes. It controlled by the Monitor Software installed at computer. Monitor software to edit testing program and BTSDA to analysis tested data. 2.Every unit BTS5V12A battery testing equipment has 8 channels and could be installed Max.10 units on a rack make up 80 channels.Each of channel could work independently with different charge discharge program at same time. 3.Neware battery testing equipment has constant current charge,constant voltage charge,constant current and voltage charge,constant power charge,constant current discharge,constant voltage discharge,constant power discharge,constant resistance discharge. 4.5V12A battery testing equipment widely used in Pouch Cell Testing,Mobile Battery Testing,Cylindrical Cell Testing,Production Line Testing,Super- capacitor Testing and Lab Battery Materials Research. 5.The Neware battery testing equipment is suitable for all kinds rechargeable batteries such as lithium battery, NI-MH battery, Zn-Mn watch battery and so on. Key Technology Parameters: Voltage Range:25mV~5V Lowest Discharge Voltage:1.5V Voltage Testing Precision:±0.05% Current Range 1:5mA~1A; Current Range 2:1A~6A; Current Range 3:6A~12A Current Testing Precision:±0.05% Primary Applications: Pouch Cell Testing 3C Batteries Testing Mobile Battery Testing Cylindrical Cell Testing Production Line Testing Super-capacitor Testing Lab Battery Materials Research Key Features: DCIR Testing Pulse Testing Capacity Testing Cycle Life Testing Testing Data Analysis Charge/Discharge Testing

Minimum Order: 1 bags

HDL-360 speed adjustable x-ray film dryer Technical parameters and specifications ● Drying process: → → Water washing → → Drying → → ● Film development speed: 40-240s adjustable ● Sheet feeding width:. 360 m ● Moving speed: 710mm/min (running time: 40 seconds) ● Dry tablet quantity 80X360mm (4 "X14") film 450 sheets per hour (dry film speed 40s) ● Power supply: 200-240V. 50/60Hz 5A ● Water consumption: 2 l/min during film operation ● Volume: 560mmX480mx545 (length x width x height) ● Add the function of chip induction ● Improved air duct, higher drying efficiency ● Roller shaft: DuPont foamed uranium is used to ensure that it will not harden within 5 years ● Shell: engineering PVC plastic ● Heating element: PTC heating element ● Temperature control mode: constant temperature control with solid-state relay ● Optional parts: water washing circulating device, which aims at no tap water, poor water quality or frequent water stoppage at the use site For Speed Adjustable X-Ray Film Dryer Chip Induction Non Destructive Testing Equipment 0

High-Current Probe Pogo Pin P350(150) for Electronic Test Cable harness test probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. Their standard and requirements are higher than other series of test probes. They can be divided into screw-thread harness test probes, cable harness switch probes, non-screw-thread harness test probes, position-limited harness test probes and cable harness high-current probes, etc. High-current probes can withstand high current and high temperature in the tests. They are mainly applied to the in-circuit test field of high temperature and high current environments. High-current probes manufactured by Centalic mainly include P203, P264, P265, P350 and P420, etc. There is a fixed schedule for mass production of P350(150)-H-14G(C) This probe can withstand the current up to 20 Amps. And its typical maximum contact resistance is 50 milliohms. The materials used for the construction of this high-current test probe are different for each component: The barrel is made of brass. Subsequently gold and nickel plated during the galvanic plating phase. The spring is made of gold plated music wire. The plunger is made of SK4, then gold and nickel plated. The plunger tip is made of brass, then gold and nickel plated. For details, please check parameters in below table. Technical Specifications Recommended Current Rating: 20 amps, continuous Contact Resistance: 50 millohms, max Full Stroke: 7.5 mm Rated Stroke: 5 mm Spring Force: 397 gf at load 5 mm For more information, please check below catalog. Company Information: Centalic Technology Development Ltd. was founded in 1980. Specializing in R&D, manufacture, sales and technical service, Centalic is one of the earliest high-tech enterprises which concentrates on large-scale production of various test probes and precision metal parts, and has a professional manufacturing base owning complete production lines and test equipment. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big- current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Our company owns professional R&D, production, sales teams under the working principle of 'quality, punctuality, confidentiality' to totally efficiently develop test probes in accordance with the requirements of customers' test projects and meet the needs of customers for mass production as well as developing markets. With many years' continuous endeavour of our staff, Centalic has built a solid foundation in this industry and our products have been sold all over the world. Welcome to browse our website and download any catalogs of our products. If you need a complete set of product manual, please feel free to contact us. Many products are not uploaded due to a huge range. If you can't find what you need, please feel free to contact us. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal

Minimum Order: 100

High-Current Probe Pogo Pin P203 for Electronic Test Cable harness test probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. Their standard and requirements are higher than other series of test probes. They can be divided into screw-thread harness test probes, cable harness switch probes, non-screw-thread harness test probes, position-limited harness test probes and cable harness high-current probes, etc. High-current probes can withstand high current and high temperature in the tests. They are mainly applied to the in-circuit test field of high temperature and high current environments. High-current probes manufactured by Centalic mainly include P203, P264, P265, P350 and P420, etc. There is a fixed schedule for mass production of P203. This probe can withstand the current up to 17 Amps. And its typical maximum contact resistance is 80 milliohms. The materials used for the construction of this high-current test probe are different for each component: The barrel is made of phosphor bronze. Subsequently gold and nickel plated during the galvanic plating phase. The spring is made of gold plated music wire. The plunger is made of beryllium copper, then gold and nickel plated. For details, please check parameters in below table. Technical Specifications Recommended Current Rating: 17 amps, continuous Contact Resistance: 80 milliohms, max Full Stroke: 6.35 mm Rated Stroke: 4.3 mm Spring Force: 115 gf (4 oz) at load 4.3 mm For more information, please check below catalog. Company Information: Centalic Technology Development Ltd. was founded in 1980. Specializing in R&D, manufacture, sales and technical service, Centalic is one of the earliest high-tech enterprises which concentrates on large-scale production of various test probes and precision metal parts, and has a professional manufacturing base owning complete production lines and test equipment. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big- current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Our company owns professional R&D, production, sales teams under the working principle of 'quality, punctuality, confidentiality' to totally efficiently develop test probes in accordance with the requirements of customers' test projects and meet the needs of customers for mass production as well as developing markets. With many years' continuous endeavour of our staff, Centalic has built a solid foundation in this industry and our products have been sold all over the world. Welcome to browse our website and download any catalogs of our products. If you need a complete set of product manual, please feel free to contact us. Many products are not uploaded due to a huge range. If you can't find what you need, please feel free to contact us. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal

Minimum Order: 100

High-Current Probe Pogo Pin P420 Series for Electronic Test Cable harness test probes are mainly used directly or for the tests of automotive industry. Parts of them are also applied to communication electronics, medical equipment, equipment automation, etc. Their standard and requirements are higher than other series of test probes. They can be divided into screw-thread harness test probes, cable harness switch probes, non-screw-thread harness test probes, position-limited harness test probes and cable harness high-current probes, etc. High-current probes can withstand high current and high temperature in the tests. They are mainly applied to the in-circuit test field of high temperature and high current environments. High-current probes manufactured by Centalic mainly include P203, P264, P265, P350 and P420, etc. There is a fixed schedule for mass production of P420-HP-19G(C). This probe can withstand the current up to 20 Amps. And its typical maximum contact resistance is 20 milliohms. The materials used for the construction of this high-current test probe are different for each component: The barrel is made of brass. Subsequently gold and nickel plated during the galvanic plating phase. The spring is made of gold plated music wire. The plunger is made of SK4, then gold and nickel plated. The plunger tip is made of brass, then gold and nickel plated. For details, please check parameters in below table. Technical Specifications Recommended Current Rating: 20 amps, continuous Contact Resistance: 20 milliohms, max Full Stroke: 9 mm Rated Stroke: 5 mm Spring Force: 540 gf at load 5 mm For more information, please check below catalog. Company Information: Centalic Technology Development Ltd. was founded in 1980. Specializing in R&D, manufacture, sales and technical service, Centalic is one of the earliest high-tech enterprises which concentrates on large-scale production of various test probes and precision metal parts, and has a professional manufacturing base owning complete production lines and test equipment. Our products include semiconductor test probes, in-circuit test probes, radio frequency probes, harness probes, battery contact probes, switching probes, big- current probes, spring probes, universal complex test probes, wafer probes, and so on. They are widely applied to the tests of various electronic products, such as in-circuit tests of semiconductor components, chips, PCB and other electronic peripherals. Our company owns professional R&D, production, sales teams under the working principle of 'quality, punctuality, confidentiality' to totally efficiently develop test probes in accordance with the requirements of customers' test projects and meet the needs of customers for mass production as well as developing markets. With many years' continuous endeavour of our staff, Centalic has built a solid foundation in this industry and our products have been sold all over the world. Welcome to browse our website and download any catalogs of our products. If you need a complete set of product manual, please feel free to contact us. Many products are not uploaded due to a huge range. If you can't find what you need, please feel free to contact us. Notice: Stock: standard product. As usual, they are in stock. Express: DHL, FedEx, UPS, etc. Payment: T/T, PayPal

Minimum Order: 100

JUNSUN's Oil-immersed Type/ Dry Type AC/DC Withstand Voltage Hipot Tester is suitable for power system to detect the insulating performance of all electrical equipment, high voltage power sources, or equipment with DC high voltage small current. 1. Impedance voltage: 4.5%-8% 2. Output voltage waveform: sine wave 3. Surface temperature rise:<55℃ 4. No-load loss consumption: 0.2% - 0.35% 5. Allowable continuous operation time: 2 hours 6. Interrupted operation time: continuous

Minimum Order: 1 bags

1. Winding deformation test based on different standards of sweeping frequency method. 2. It can measure the phase frequency curve and amplitude frequency curve of each winding of the transformer. 3. It can cyclically test of phase and amplitude of transformer windings at fixed frequency. 4. Analyze the transformer amplitude-frequency curve based on IEC standard. 5. Built-in non-dropout memory, winding deformation can be saved for 40 groups. 1. Sweeping frequency method to measure winding deformation. Scan frequency range: 10HZ-1MHZ (DLT911-2016 0.5KHZ interval linear scan) 20HZ-2MHZ (GB/T-1094.18 IEC60076-18:2012 segmented scanning) 10HZ-10MHZ (GB/T-1094.18 IEC60076-18:2012 segmented scanning) 1KHZ -1000KHZ_1.0(Linear scan 1KHZ interval PC side available) 1KHZ -1000KHZ_0.5(linear scan 0.5KHZ interval avaiable4 for Pc) 1KHZ -2000KHZ_1.0(linear scan 1KHZ interval available for PC) 1KHZ -2000KHZ_0.5(linear scan 0.5KHZ interval available for PC) 100HZ-1000K(Segmented scan PC available 1441 points): 100HZ-1KHZ 5HZ interval 180 points 1KHZ-10KHZ 50HZ interval 180 points 10KHZ-100KHZ 500HZ interval 180 points 100KHZ-1000KHZ 1KHZ interval 901 points 100HZ-2000K(Segmented scan PC available 2441 points) 100HZ-1KHZ 5HZ interval 180 points 1KHZ-10KHZ 50HZ interval 180 points 10KHZ-100KHZ 500HZ interval 180 points 100KHZ-1000KHZ 1KHZ interval 900 points 1000KHZ-2000KHZ 1KHZ interval 1001 Points Amplitude measurement range: (-100dB) - (+20dB) Amplitude measurement accuracy: (-40dB) - (+20dB) 0.2dB (-60dB) - (-40dB) 0.5dB (-80dB) - (-60dB) 1.0dB Angle measurement range: (-180°) - (+180°) (10HZ-2MHZ) Scan frequency accuracy: less than 0.01% Signal input impedance: greater than 1M Ω(DLT911-2016) 50 Ω(GB/T-1094.18 IEC60076-18:2012) Signal output impedance: 50 Ω. Same-phase test repetition rate: 99.5%.

Minimum Order: 1 bags

IIJ-II-100 Series Transformer Oil Breakdown Voltage Tester is specially designed for testing the breakdown voltage of transformer oil and other kinds of insulating oils. IIJ-II-100 Series Transformer Oil Breakdown Voltage Tester adopts industrial single-chip control system, large-scale integrated circuit, new-style I/O interface, coupled with unique detection and anti-interference technology, the performance of the equipment has been greatly improved. Breakdown voltage testing of insulating oils can help to assess the condition of these oils within electrical equipment, such as transformers, capacitors, switches, etc. Based on the test results, the oil can be identified as aged due to an increase in water content, sludge, or if the oil has oxidized. KEY FEATURES: 1. Simple operation, automatically (can be finished just press on key). 2. Menu controlled. Input data is clear. 3. Can store 99 groups of oil testing data, which is convenient to reading and print. The testing data can keep 10 years under the condition of power off. 4. System time can go on running under power off; (The system time is just for reference which cannot be the standard of timing). 5. High capacity of anti-jamming, high precision of testing. 6. Small volume, light weight, which can be operated in the open air very conveniently.

Minimum Order: 1 bags

Products Description DTS-CT intelligent precision thermostatic bath is a new type of intelligent thermostat introduced by our company. It adopts touch screen control and operation, completely intelligent man-machine interface, and the control is more convenient, simple and practical. A dual-cavity side stirring technology is used in the structure to make the constant temperature bath reach the ideal uniform temperature field through intelligent PID adjustment, which can meet the verification / calibration work of various temperature sensors such as low temperature thermocouples, industrial thermal resistors, pressure thermometers, bimetallic thermometers, glass liquid thermometers, etc. Functional characteristics 1.Intelligent Manipulation Large touch screen control, intelligent man-machine interface, multi-function display window, control more intuitive, simple and fast; 2.Slope heating The temperature control rate is adjustable, the heating rate is set according to the actual verification or calibration, and the temperature rise is uniform, which meets the verification / calibration of various temperature switches. 3.Volatility tips Wave motion of 10 or 1 min can be displayed, the fluctuation can be calculated automatically, and the temperature is judged intuitively. 4.Intelligent rehydration The automatic rehydration function can be set up, and the oil transportation system can complete the rehydration function after starting, so as to avoid the safety and unstable factors caused by the reduction of liquid level. 5.Intelligent mixing At room temperature, without starting temperature control, the control system automatically closes the stirring motor, prolongs the service life of the equipment and reduces noise. 6.Double sensor overheating protection Built-in hardware and software dual protection, using dual sensors to monitor the operation process. Hardware overheating protection, completely separated from the main control system independent operation, overtemperature automatic power cut off, more safe and reliable. 7.Precision temperature control Adopt imported AA level temperature control sensor and variable parameter temperature control algorithm to ensure the maximum rate"zero" overshoot stability at different temperature points. 8.Excellent stability and uniformity of temperature field Special structure, blocking stage heat insulation treatment, intelligent adjustment of stirring speed, advanced adaptive control algorithm, so that the constant temperature bath has excellent temperature field stability and temperature field uniformity; 9.Multipoint calibration Adopt multi-point calibration algorithm to realize built-in standard and precision temperature measurement. 10.Communication function Support USB 、WIFI、WLAN、 serial communication function; 11.Curves show free scaling Real-time curve display, support multi-touch, free scaling function; 12.Ergonomic design The intelligent temperature control instrument adopts three-axis mechanical cantilever installation, the angle length is adjusted at will, does not occupy the slot table space, is convenient to operate; 13.Composite thermal insulation design A variety of insulation materials, composite insulation design, limiting internal heat spillover. 14.Oil pollution prevention design The countertop is designed with an integrated operating table, and the built-in overflow loop prevents the liquid medium from flowing to the bath table, and the removable stirring motor cover is convenient to clean up the oil pollution quickly. Product Paramenters Patent certificate Whatsapp: 0086 13810587138 same with Wecha E-mail: dickecheng@gmail.com

Minimum Order: 1 bags

Shengda water meter CO.,LTD focus On R&D And Produce Mechanical Water Meter, Smart Water Meter,Ultrasonic water meter and flow meter since 1995,we not only produce water meter,also offer total solution of smart water meter reading,support OEM/ODM. 1.Size:DN15-DN200 2.Body:Brass( , with valve)/iron(without valve) 3.Type:Dry dial/wet dial(standard) 4.Max work pressure:PN16. 5.Protection class:IP68 6.Protocol: Narrow band(LTE Cat.NB) 7.Frequency: B3(1800),B5(850),B8(900) 8.Battery: more than 6 years 9.Pressure loss:≤0.063Mpa 10.Water temperature:T30/T90 11.Standards:ISO4064. 12.Certificate:MID 13.SIM card:Micro SIM card(Type 3FF) 14.Working mode: Class A 15.Software: B/S Cloudy serve platform 16.Software payment: Supply for free 17.Composition:NB-Iot water meter, Base station, Serve Platform please check our NB-IOT water meter solution. Contact person : Miranda Office Email: admin(at)henanpanda(dot)com WhatsApp:+86 18603780816 SHENGDA water meter CO.,LTD

Minimum Order: 1 bags

JSDY-021 SERIES TRANSFORMER OIL DIELECTRIC STRENGTH TESTER is specially designed for testing the breakdown voltage of transformer oil and other kinds of insulating oils. Breakdown voltage testing of insulating oils can help to assess the condition of these oils within electrical equipment, such as transformers, capacitors, switches, etc. Based on the test results, the oil can be identified as aged due to an increase in water content, sludge, or if the oil has oxidized. FUNCTIONS & FEATURES: 1. High accuracy, long service life. 2. The test process is fully in compliance with the requirements of IEC 60156. 3. User-defined test. 4. Proof test. 5. The test process and result is displayed in real time on the LCD screen. 6. All parameters of the test process can be set. 7. The built-in EEPROM memory can save up to 100 groups of test data and results. 8. The built-in micro-printer can print the test results at any time. 9. All the human-machine interaction operations can be completed by rotating the mouse. 10. RS232 interface, upload test data to computer and make Word format test report. 11. Calibration interface available. 12. The tester is easy to operate, powerful, stable and reliable, and it has an excellent anti-interference ability.

Minimum Order: 1 bags

Functions: Breakdown test of user-defined Proof test IEC60156/IS6792/BS5874 test ASTM D1816 standard test ASTM D877 standard test 5 minutes standard test Manual test Calibration interface for customers Uploading data to PC and making word report automatically Result print Specifications: Output voltage:AC 0V~100KV Rate of voltage rise: 0.5kv/s±5%, 2kv/s±5%, 3kv/s±5%,5kv/s±5% Max test times setting for user-defined mode: 9 Stir time setting for user-defined mode: 0~999s Waiting time setting for user-defined mode: 0~999s Test error: 3%RDG+0.3%FS Display: 256´128 LCD Maximum storage capacity: 100 groups of test data Power supply : AC220V±10%, 50Hz/60Hz Environment temperature: 0-50℃ Relative humidity ≤80%RH Weight:41kg Size:620mm*430mm*330mm

Minimum Order: 1 bags

Optional Accessories of test chamber 1. Low humi. Dehumidifying system 2. Inner glass door with manual operating ports 3. Temp./ humi. Recorder 4. Pure water treatment device 5. Reverse osmosis water purifier 6. RS-485 interface can be linked to PC and achieve multi-level control and recording software management. 7. LN2 / LCO2 fast cooling-down system Temperature humidity drug stability test chamber price can be used when constant climate conditions (temperature and/or humidity) are needed for product testing. It also can be used for a variety of materials of high - low temperature alternating test. The test temperature, humidity, time can be programmed. Provides conditions of temperature from -70 to +150 degree and of humidity from 20% to 98%, low humidity 10%~98%RH is available for us..

JS-023A SERIES TRANSFORMER OIL DIELECTRIC STRENGTH TESTER is specially designed for testing the breakdown voltage of transformer oil and other kinds of insulating oils. Breakdown voltage testing of insulating oils can help to assess the condition of these oils within electrical equipment, such as transformers, capacitors, switches, etc. Based on the test results, the oil can be identified as aged due to an increase in water content, sludge, or if the oil has oxidized. (1) AC220V±10% power supply input (2) Output voltage：AC 0~100KV (0-80KV can be customized) (3) Rate of voltage rise: 0.5kv/s±10%, 2kv/s±5%, 3kv/s±5%,5kv/s±5% (4) Max test times: 9 (5) Init wait times:0~999s (6) Stir time: 0~999s (7) Wait time: 0~999s (8) Measurement accuracy: ±(1% of full scale + 2 digits) Resolution:0.1KV (9) Temperature measurement: Measurement range : 0℃ to 70℃, or better Temperature resolution : 1℃, or better Operating temperature : up to 45℃ (10)Storage:100 groups (11)7 inch colorful LCD with touch pad (12)Oil test vessel temperature measurement unit (13) Weight 38kg (14) Size: 460 mm*380mm*360mm

Minimum Order: 1 bags