Offers to Sell

■ Forced open action device(NC contacts only), it can disconnect the contact when the contact has fusing and other failures. ■ Standardized gold-clad contacts provide high contact reliability, Can be used with both standard loads and microloads. ■ Strengthened top seal structure improves the sealing performance. ■ Built-in contact holder has fast-action type: 1NC/1NO; Slow-action: 1NC /1NO and 2NC. Characteristics Protection level*1 IP66 Life*2 Electrical More than 300,000 times (AC250V 10A, resistive load) Electrical More than 500,000 times (AC250V 3A, resistive load) *3 Operating speed 1 ～ 500mm/s(T4N-4120) Operating frequency Max. 30 times/min Contact resistance 25 mΩ or less Minimum working load *4 1mA resistive load below DC5V (N standard reference value) Rated insulation voltage (Ui) 300V Electric shock proof protection grade Class II (double insulated) Pollution degree (environmental conditions) Pollution degree 3 (EN60947-5- 1) Withstand voltage (EN60947-5-1) Between homopolar terminals: 2.5kV Between heteropolar terminals: 2.5kV Between terminals and uncharged metal parts: 6kV insulation resistance Above 100MΩ Contact gap Minimum 2×0.5mm quick-action type, Minimum 2×2mm slow-action type Vibration Malfunction 10 ～ 55Hz 0.75mm single amplitude Impact Duration 1,000m/s2 Malfunction 300m/s2 Ambient temperature -20 ～ +70℃ (No ice or dew) Ambient humidity Less than 95% RH Weight About 73g (T4N-4120) About 82g (T4N-4120 with gland) Note1:The above values are initial values. Note2:Once the contact is connected to a standard load, it can not be used to connect a smaller load. If so, the contact may result in rough surface, thus losing contact reliability. ①The protection level is gotten based on test method of (EN60947-5-1). Please make sure its sealing under actual environmental conditions before use. The switch box has dust and oil resistance structure, but it should be used in places without dust, oil and chemicals. Otherwise it may lead to premature wear, damage or malfunction. ②The durability is for ambient temperature of 5℃ ~ 35℃ and humidity of 40% to 70% RH. ③For additional details, please contact us. ④When the ambient temperature is above 35℃ , more than 2 circuits 3A 250VAC loads are prohibited. ⑤The values will vary with different switching frequency, environmental conditions, reliability level and other factors. Please confirm on the actual load in advance. The mechanical life of deadman lever type is more than 10,000,000 times. Safety Limit Switch Model Designations Item Code Description ① Conduit / connector size 1 Pg13.5 (1 conduit type) 2 G1/2 (1 conduit type) 4 M20 (1 conduit type) 5 Pg13.5 (2 conduits type) 6 G1/2 (2 conduits type) 8 M20 (2 conduits type) ② Built-in switch 1 1NC/1NO (quick-action type) 2 2NC (quick-action type) A 1NC/1NO (slow-action type) B 2NC (slow-action type) ③Head and driving rod 20 Roller lever (resin lever, resin ball) 22 Roller lever (metal lever, resin ball) 25 Roller lever (metal lever, metal resin ball) 2G Adjustable roller lever, Form Lock (metal lever, resin ball) 2H Adjustable roller lever, Form Lock (metal lever, rubber ball) 2M Adjustable roller lever, Form Lock (metal lever, metal resin ball) 31 Top plunger type 32 Top plunger ball type 62 Unilateral cantilever ball type (horizontal) 72 Unilateral cantilever ball type (vertical) 80 Whisker type 87 Plastic stick type

■ Stainless steel idler wheel, punch and spring; ■ Selective M18x1.5 cable gland. Ratings Rated voltage Noninductive Load (A) Inductive Load (A) Resistance Load Lamp Load Inductive Load (A) Motor Load NC NO NC NO NC NO NC NO 125VAC 5 5 1.5 0.7 3 3 2 1 250VAC 5 5 1 0.5 3 3 1.5 0.8 8VDC 5 5 3 3 5 4 3 3 14VDC 5 5 3 3 4 4 3 3 30VDC 5 5 3 3 4 4 3 3 125VDC 0.4 0.4 250VDC 0.2 0.2 Inrush Current N.C: below  24A, N.O: below  12A NOTE:  1. Inductive load has a power factor of 0.4 min.(AC) and a time constant of 7 msec.max.(DC). 2. Lamp load has an inrush current of 10 times the steady-state current,while motor load has an inrush current of 6 times the steady-state current. 3. Product with spring, its usable range of operating part is within one third of the whole spring length from the front end of spring. Characteristics Operation speed 0.5mm-50cm/sec Operating frequency Electical: 30 operations/minute Contact resistance 25mΩ max. (initial value) Insulation resistance 100MΩ min. (below 500VDC) Dielectric Strength 1000VAC, 50/60 Hz for 1 minute between terminals of the same polarity 1500VAC, 50/60 Hz for 1 minute between current-carrying and non- current-carrying metal parts 1500VAC, 50/60 Hz for 1 minute between each terminal and ground Vibration 10-55Hz,1.5mm double amplitude Shock Mechanical durable: 1, 000m/Sec2 (about 100G'S) Malfunction: 300m/Sec2 (about 30G'S) Ambient Temperature  -10~+65℃ (With no icing) Humidity <95% RH Weight About 195 to 246g Electrical Life Above 500000 Degree of protection IP65 Operating Characteristics Operating Characteristics Model TSA-001 TSA-003 TSA-012 TSA-021 TSA-041 TSA-031 TSA-051 TSA-061 TSA-071 TSA-081 Operating force OF  (Max) 7.84N 7.84N 7.84N 3.92N 3.92N 3.92N 3.92N 1.47N 1.47N 1.47N Release force RF  (Min) 3.92N 3.92N 3.92N 0.98N 0.98N 0.98N 0.98N 0.49N 0.49N 0.49N Pre-travel PT  (Max) 1.8mm 1.8mm 1.8mm 20° 20° 20° 20° 30mm 30mm 30mm Tripping position TP±10% 2.0mm 2.0mm 2.0mm 22.5° 22.5° 22.5° 22.5° 22.5° 22.5° 22.5° Movement differential MD (Max) 1.2mm 1.2mm 1.2mm 10° 10° 10° 10° 14° 14° 14° Over travel OT  (Min) 4.0mm 4.0mm 4.0mm 75° 75° 75° 75° 20mm 20mm 20mm Total travel TT  (Min) 5.8mm 5.8mm 5.8mm 95° 95° 95° 95° 50mm 50mm 50mm Rotary indexing 22.5° 22.5° 22.5° 22.5° visit our website: https://www.chinalimitswitch.com/limit-switch/

■ Double-circuit type of limit switch. ■ Compact new design approximately 1/3 the size of TMAZTZ vertical limit switches. ■ With strong zinc cast base, and reinforced plastics outer shell, High. Structure preventing oil, water and pressure. ■ Structure enables the terminal section to be fully opened for easy wiring. ■ Degree of protection: IP65 ■ Aslo includes stainless steel roller model TZ-8 Limit Switches TZ-8 limit switch in the specific production and manufacture, the limit switch is installed in a pre-arranged part, when the control module installed on the production of molecular thermal motion components collides with the limit switch, the contact point posture of the limit switch completes the conversion of the power supply circuit. Therefore, the limit switch is a kind of household appliance that converts the power supply circuit according to the stroke arrangement part of the fitness exercise component, and its basic principle of efficacy is similar to that of the button. Ratings Rated voltage Noninductive Load (A) Inductive Load (A) Resistance Load Lamp Load Inductive Load (A) Motor Load NC NO NC NO NC NO NC NO 125VAC 5 5 1.5 0.7 3 3 2 1 250VAC 5 5 1 0.5 3 3 1.5 0.8 8VDC 5 5 3 3 5 4 3 3 14VDC 5 5 3 3 4 4 3 3 30VDC 5 5 3 3 4 4 3 3 125VDC 0.4 0.4 250VDC 0.2 0.2 Inrush Current N.C: below  24A, N.O: below  12A NOTE:  1. Inductive load has a power factor of 0.4 min.(AC) and a time constant of 7 msec.max.(DC). 2. Lamp load has an inrush current of 10 times the steady-state current,while motor load has an inrush current of 6 times the steady-state current. 3. Product with spring, its usable range of operating part is within one third of the whole spring length from the front end of spring. Characteristics Operation speed 0.5mm-50cm/sec Operating frequency Electical: 30 operations/minute Contact resistance 25mΩ max. (initial value) Insulation resistance 100mΩ min. (below 500VDC) Shock Mechanical durable: 1, 000m/Sec2 (about 100G'S) Malfunction: 300m/Sec2 (about 30G'S) Ambient temperature -5~+65℃ (With no icing) Humidity <95% RH Weight About 130 to 190g Degree of protection IP65 Electrical Life Above 500000 Operating Characteristics Operating Characteristics  Model TZ-8104 TZ-8107 TZ-8108 TZ-8111 TZ-8112 TZ-8122 TZ-8166 TZ-8167 TZ-8168 TZ-8169 Operating force OF   (Max) 5.88N 5.88N 7.84N 9.8N 9.8N 9.8N 0.88N 0.88N 0.88N 0.88N Release force RF   (Min) 0.49N 0.69N 0.49N 2.94N 2.94N 2.94N 一 一 一 一 Pre-travel PT   (Max) 20° 20° 20° 1.5mm 1.5mm 1.5mm 30mm 30mm 30mm 30mm Over-travel OT   (Min) 75° 75° 75° 4mm 4mm 4mm 一 一 一 一 Movement differential MD  (Max) 10° 10° 10° 1.2mm 1.2mm 1.2mm 一 一 一 一 Total travel TT   (Min) 95° 95° 95° 5.5mm 5.5mm 5.5mm 一 一 一 一 Operational position OP 一 一 一 26±0.8mm 一 一 一 一

TZ-8108 adjustable roller lever Limit Switch ■ Double-circuit type of limit switch. ■ Compact new design approximately 1/3 the size of TMAZTZ vertical limit switches. ■ With strong zinc cast base, and reinforced plastics outer shell. ■ Structure enables the terminal section to be fully opened for easy wiring. ■ Degree of protection: IP65 ■ Aslo includes stainless steel roller model Voltage Ratings Rated voltage Noninductive Load (A) Inductive Load (A) Resistance Load Lamp Load Inductive Load (A) Motor Load NC NO NC NO NC NO NC NO 125VAC 5 5 1.5 0.7 3 3 2 1 250VAC 5 5 1 0.5 3 3 1.5 0.8 8VDC 5 5 3 3 5 4 3 3 14VDC 5 5 3 3 4 4 3 3 30VDC 5 5 3 3 4 4 3 3 125VDC 0.4 0.4 250VDC 0.2 0.2 Inrush Current N.C: below  24A, N.O: below  12A NOTE:  1. Inductive load has a power factor of 0.4 min.(AC) and a time constant of 7 msec.max.(DC). 2. Lamp load has an inrush current of 10 times the steady-state current,while motor load has an inrush current of 6 times the steady-state current. 3. Product with spring, its usable range of operating part is within one third of the whole spring length from the front end of spring. TZ 8108 Limit Switch Characteristics High rigidity structure, made of high-strength plastic and aluminum; Cast (head and lid clinging to the box); Small size, waterproof and oilproof structure; Built-in micro switch, double spring mechanism, longer mechanical life; Easy wiring circuit opening design. Operation speed 0.5mm-50cm/sec Operating frequency Electical: 30 operations/minute Contact resistance 25mΩ max. (initial value) Insulation resistance 100mΩ min. (below 500VDC) Shock Mechanical durable: 1, 000m/Sec2 (about 100G'S) Malfunction: 300m/Sec2 (about 30G'S) Ambient temperature -5~+65℃ (With no icing) Humidity <95% RH Weight About 130 to 190g Degree of protection IP65 Electrical Life Above 500000 Limit Switch TZ-8108 Operating Characteristics Operating Characteristics  Model TZ-8104 TZ-8107 TZ-8108 TZ-8111 TZ-8112 TZ-8122 TZ-8166 TZ-8167 TZ-8168 TZ-8169 Operating force OF   (Max) 5.88N 5.88N 7.84N 9.8N 9.8N 9.8N 0.88N 0.88N 0.88N 0.88N Release force RF   (Min) 0.49N 0.69N 0.49N 2.94N 2.94N 2.94N 一 一 一 一 Pre-travel PT   (Max) 20° 20° 20° 1.5mm 1.5mm 1.5mm 30mm 30mm 30mm 30mm Over-travel OT   (Min) 75° 75° 75° 4mm 4mm 4mm 一 一 一 一 Movement differential MD  (Max) 10° 10° 10° 1.2mm 1.2mm 1.2mm 一 一 一 一 Total travel TT   (Min) 95° 95° 95° 5.5mm 5.5mm 5.5mm 一 一 一 一 Operational position OP 一 一 一 26±0.8mm 一 一 一 一 If you do not have the limit switch you are looking for, please contact us and we will design and manufacture your own limit switch, such as rollers or plungers, etc., as well as wiring methods can be customized according to your requirements.

CE Approve 2024 Intense Pulsed Light Hair Removal Ipl Laser Depilador Ipl Vascular Electrolysis Hair Removal Machine Home Use Ipl Machine QM-120 Different combination from IPL Diode Laser, Nd:YAG Laser, RF,etc. Applications 1. Permanent hair removal for all skin types and all hair colors! 2. Skin rejunvenation 3. Pigments removal 4. Wrinkle removal 5. Acnes removal 6. Vascular Removal Working Principle IPL Intense Pulse Light("IPL") used broad spectrum of white light and with filters to marrow the spectrum to target specfic chromophores and structures. IPL is a non-invasive skin treatment that emits powerful bursts of light energy to treat unwanted hair, sun damaged skin, and wrinkles, etc. without damaging the surface of your skin, IPL systems use flash xenon lamps to emit micro pulses of light across a broad band of visible wavelengths. IPL work by using particular wavelengths of light that is called by melanin which colors the hair and brown skin and black. Since melanin absorbs light to be warm or hot, that the production of cells called melanocytes and melanin are denatured more produce more melanin. By using gentle pulses of light momentarily to create heat, IPL can permanently disable hair follicles, preventing hair follicles` future growth. The melanin in the hair (which gives it its colour) absorbs the light, which is then converted into heat. This heat is transferred to the growth cells surrounding the root of the hair, disabling them. By the IPL, pigments are Shattered and eliminated out of body via metabolism. At the same time,IPL also helps increase collagen production, which rejuvenates the skin leading to a more youthful, radiant, bright and few fine wrinkle skin. The light with long wavelength can pass through epidermis to the hair follicles deep underneath the skin. At the targeted area, IPL occurs heating to destroy follicles and hair structures leading to permanent hair removal. SSR It is a revolutionary approach, rather that bombarding your skin with high amounts of damaging energy. SSR fires multiple shots but at low Joules, in doing so it gently heats the hair follicle to the heat needed and the most you will feel is warmth and a tingling sensation, some clients comparing it to a warm massage. SSR also utilizes In-Motion technology, where the hand piece is always in motion over the skin. Specialty of QM-120 ** Unique and Ergonomic design Handpiece.(2 designs for option) ** 5 filters for different treatment ** Top-level Spare parts adopted, guarantee its golden quality and long-lasting lifetime! Technical Specifications Model QM-120 QM-120 Electrical input 110V/230V 110V/230V Machine Power 2400W 4000W Spot size IPL 15mm*50mm sSr 15mm*50mm IPL 15mm*50mm E-light 15mm*50mm Max Energy 60J 26J 60J Pulse Number 6 10 6 Wavelength 430/530/580/640/750nm 650-950nm 430/530/580/640/750nm Laser power 1600W 3000W Capacitor 450V12000uF*3 450V12000uF*3 Water fifter Replaceable Replaceable Cooling System Air + Water + Wind + TEC semiconductor + Sapphire sking contact cooling Machine Size 44*41*120cm Packing Size 57*54*130cm

Minimum Order: 1 bags

Siemens (ASM) D feeders storage cart without power Part number: / Part name: Siemens (ASM) D feeders storage cart Size: / Condition:made in china Application: Siemens (ASM) Other ASM SIEMENS parts we have: ASM Siemens X Series feeder 2x8 00141269 00141289 2*8 feeder PN. 00141269 2*8 feeder PN. 00141289 12mm 00141271 16mm 00141272 24mm 00141273 32mm 00141274 44mm 00141275 56mm 00141276 72mm 00141277

Minimum Order: 1 bags

Siemens Stick Feeder 40MM(single Input Channels) Part name: Siemens Stick Feeder 40MM Condition:original new / original used and working well Application: Siemens Siemens Stick Feeder 40MM(single Input Channels) Voltage: 220V Width: 40MM (single Input Channels ) Overall size : 320 x 30 x 95 mm, H * W* H Other ASM SIEMENS parts we have: ASM Siemens X Series feeder 2x8 00141269 00141289 2*8 feeder PN. 00141269 2*8 feeder PN. 00141289 12mm 00141271 16mm 00141272 24mm 00141273 32mm 00141274 44mm 00141275 56mm 00141276 72mm 00141277

Minimum Order: 1 bags

Product Name: Nickel Alloy Wire, Stainless Steel Wire Shape: Round, Square, Flat, Hexagonal etc. Standard: GB, AISI, ASTM, DIN, EN, JIS Process: Hot Rolled, Cold Rolled, Forged Size: Can Be Customized Inspection: TUV, BV, ABS, LR etc. Payment: TT, LC, OA, DP, Alibaba Trade Assurance, Bank Garantee etc.

Minimum Order: 1 bags

Product Name: Forging Bar, Forging Ring, Forging Shaft, Forging Circle, Forging Blocks etc. Standard: GB, AISI, ASTM, DIN, EN, JIS Process: Forged Size: Can Be Customized Shape: Round, Square, Hex, Hollow etc. Surface Treatment: NO.1, 2B, NO.4, BA, HL, Mirror etc. Payment: TT, LC, OA, DP, Alibaba Trade Assurance, Bank Garantee etc.

Minimum Order: 1 bags

Product Name: Nickel Alloy Fittings, Stainless Steel Fittings Standard: GB, AISI, ASTM, DIN, EN, JIS Size: Can Be Customized Packing: Waterproof Polybag, Wooden Box Inspection: TUV, BV, ABS, LR etc. Payment: TT, LC, OA, DP, Alibaba Trade Assurance, Bank Garantee etc.

Minimum Order: 1 bags

ASM Siemens X Series feeder 2x8 00141269 00141289 Part number: 00141269 00141289 Part name: ASM X 8mm feeder Size: 8mm Condition:original new / original used and working well Application: ASM Other ASM SIEMENS parts we have: ASM Siemens X Series feeder 2x8 00141269 00141289 2*8 feeder PN. 00141269 2*8 feeder PN. 00141289 12mm 00141271 16mm 00141272 24mm 00141273 32mm 00141274 44mm 00141275 56mm 00141276 72mm 00141277

Minimum Order: 1 bags

Product Name: Nickel Alloy Pipe, Nickel Alloy Tube, Stainless Steel Pipe, Stainless Steel Tube Shape: Round, Square, Rectangular etc. Standard: GB, AISI, ASTM, DIN, EN, JIS Process: Seamless, Welded Size: Can Be Customized Inspection: TUV, BV, ABS, LR etc. Payment: TT, LC, OA, DP, Alibaba Trade Assurance, Bank Garantee etc.

Minimum Order: 1 bags

Product Name: Nickel Alloy Coil, Nickel Alloy Strip, Stainless Steel Coil, Stainless Steel Strip Standard: GB, AISI, ASTM, DIN, EN, JIS Process: Hot Rolled, Cold Rolled Size: Can Be Customized Surface Treatment: NO.1, 2B, NO.4, BA, HL, Mirror Inspection: TUV, BV, ABS, LR etc. Payment: TT, LC, OA, DP, Alibaba Trade Assurance, Bank Garantee etc.

Minimum Order: 1 bags

Product Name: Nickel Alloy Plate, Nickel Alloy Sheet, Stainless Steel Plate, Stainless Steel Sheet Standard: GB, AISI, ASTM, DIN, EN, JIS Process: Hot Rolled, Cold Rolled, Forged Size: Can Be Customized Surface Treatment: NO.1, 1D, 2D, 2B, NO.4, BA, HL, Mirror, Embossim, Sandblasted Inspection: TUV, BV, ABS, LR etc. Payment: TT, LC, OA, DP, Alibaba Trade Assurance, Bank Garantee etc.

Minimum Order: 1 bags