Offers to Sell

　　Radial shaft seal rings are ready-to-fit seals for sealing rotating shafts. They consist of an outer elastomer casing and a reinforcement ring located inside. The tension spring provides compression pressure of the sealing lip on the reinforced shaft and contributes to sealing in static areas. 　　Form A: single lip, model conforming to standard DIN 3760 (ISO 6194/1) smooth outside diameter. 　　Form AS: double lip, model according to DIN 3760 (ISO 6194/0) smooth outside diameter, with dust lip for protection against impurities from the outside. 　　The NBR material has high wear resistance and is resistant to fuels, oils, hydraulic oils and greases. 　　Usage limits: 　　Circumferential speed (m/s): ≤12 　　Pressure (MPa/bar): ≤0.05/0.5 (radial shaft seal rings are generally designed for use at atmospheric pressure). 　　Temperature range : 　　-40°C up to +100°C. 　　Tolerances: 　　Acc , ommodation : 　　Recommended tolerance H8. 　　Surface roughness Ra 1.6 to 6.3 μm.

Minimum Order: 10 long tons

　　O-rings are sealing elements providing a seal against liquid and gaseous media. They are suitable for secondary static and dynamic use. O-rings can be integrally sealed radially or axially. Sealing is created during assembly by axial or radial compression of the section. In working condition, the fluid pressure increases the deformation of the O-ring and therefore strengthens the sealing function. For optimal sealing, choose O-rings with the largest possible torus diameter. 　　In the assembly space, pay particular attention to the following elements: groove filling, precompression, elongation and settlement. 　　During static use, the precompression should be between 15 and 30% of the torus diameter. During dynamic use, it should be between 10 and 18% (hydraulic) or between 4 and 12% (pneumatic). 　　When fitted, the O-ring must be: 　　- expanded by max. 6% of inside diameter 　　- tablet of max. 3% of inside diameter. 　　The NBR material has high wear resistance and is resistant to lubricating oils and greases based on mineral oils, hydraulic oils H, HL, HLP, hardly flammable pressurized liquids HFA, HFB, HFC, aliphatic hydrocarbons, oils and silicone grease, water up to approx. 80°C. 　　Temperature range : 　　-30°C up to +100°C

Minimum Order: 10 long tons

Product Description Perfectly Straight, Incredibly Stiff, Lightweight Matte Finish Carbon Fiber Tube Carbon fiber tube is made of carbon fiber composite pre-dipped into phenylethylene polyester resin and heated, solidified, and extruded (entangled). Carbon fiber is the ultimate material for the fire staff and other long props. Perfectly straight, incredibly stiff, and ultra-lightweight, this material is ideal for contact staff. It won't bend and will far outlast aluminum construction. The direction of the fibers and thickness of the wall minimizes flexing which makes it much more responsive and eliminates wobbles. The matte finish is ideal for ensuring the grip material stays affixed to the staff and never causes problems. Product Description We use different molds to produce carbon fiber pillars of different shapes, such as round tubes, square tubes, rectangular tubes, octagonal tubes and so on. In the production process, we can also pack 3K for surface packaging and beautification. Technical Characteristics 1. High strength and high efficiency. The tensile strength is several times higher than that of ordinary steel, and its elastic modulus is better than that of steel. It has excellent creep resistance, corrosion resistance, and shock resistance. 2. Light weight and good flexibility. Carbon fiber tube has high strength, the quality is only 1×5 of steel, has high toughness, can be coiled, and can be supplied at a larger length without a lap connection. 3. The construction is convenient and the construction quality is easy to be guaranteed. The material does not need pre-processing, the working procedure is convenient, and the plate is allowed to cross. 4. Good durability and corrosion resistance. It is resistant to acid, alkali, salt, and atmospheric environment, and does not need regular maintenance. 5. With electrical conductivity. Pay special attention to electricity prevention when using. Material Matte Finish Carbon Fiber Tube Shape Round Technology Roll-wrapped or pultrusion Dimension The existing inner diameter of the mold is 4mm-50mm with a length of 1m. Customizable size: The maximum diameter can be 200mm, the longest can be 3m. Surface Black glossy/matte surface/painted Glossy 3k weave/matte 3k weave Color metal wire weave Feature lightweight, high strength Working Temperature Usually, -30-120 degrees, if special requirement, please let us know. Place Of Origin China Function Marine, Agriculture Tools, Arrow Shaft, Medical, Sport Products Tolerance Diameter Tolerance: +/-0.1mm Length Tolerance +/-1mm Our Service: 1. It ensures that a year of quality assurance and 24 hours online customer service. 2. Protection of your sales area, ideas of design, and all your private information. 3. Request for samples is accepted. 4. Drilling and slotting are accepted. 5. We guarantee the products to be manufactured with the finest materials and mature technics. All tubes can be repaired at no charge if returned to us, postage prepaid, within one year. Perfectly Straight, Incredibly Stiff, Lightweight Matte Finish Carbon Fiber Tube 0Perfectly Straight, Incredibly Stiff, Lightweight Matte Finish Carbon Fiber Tube 1Perfectly Straight, Incredibly Stiff, Lightweight Matte Finish Carbon Fiber Tube 2Perfectly Straight, Incredibly Stiff, Lightweight Matte Finish Carbon Fiber Tube 3Perfectly Straight, Incredibly Stiff, Lightweight Matte Finish Carbon Fiber Tube 4

Octagonal Hot Dip Galvanized Steel Tubular Pole Lap Joint Type Power Steel Poles Product Description: Our steel pole, steel poles , steel power poles , power distribution equipment , electric power transimission &distribution steel poles ,hot-dip-galvanized steel poles ,lamp poles ,street lamp poles ,solar street lamps steel poles ,high mast lamp poles,road lamp poles, the steel street lamp poles, hot-dip- galvanized steel lighting ,outdoor lighting ,outdoor lamps ,street lighting poles ,steel post ,street poles, lamp parts ,lighting fixture ,lighting poles ,lighting equipment ,lighting decoration ,lighting product , street lighting body, high mast lighting steel poles &tower,electric poles, round&square street lighting steel poles with double arm or single arm . Stainless steel poles, Flag mast stainless steel pole, aluminum street light poles, traffic lighting steel poles, telecom tower poles are made by hot-roll steel coil ,the process as cut plate, bending ,forming,automatic welding,drill holes ,quality check before galvanized, hot dip galvanized or powder coating , final quality check according by client required. Product Specification: Products Octagonal Hot Dip Galvanized Steel Tubular Pole Lap Joint Type Power Steel Poles Application Electrical Power Transformer Substation Voltage Grade 220KV Once Forming 16m Once forming without joint Connection structure Overlap / flange connection Shape Octagonal Welding According to AWS D 1.1, CO2 welding or submerged arc auto methods Life Period More than 25 years, it is according to installing environment Painting According to clients' request Joint Joint with insert mode, flange mode. Octagonal Hot Dip Galvanized Steel Tubular Pole Lap Joint Type Custom Painting 0 Production Process: All of our material are purchased from famous factory to assure the high quality. A factory certificate issued by the factory with stamp and signature must be provided before unloading the material in our factory , otherwise we have rights to refuse. Before put into production , all the material must be passed the chemical and physical analysis to make sure that they have met the requested strength and component. Inspection To assure our products qualified , we take steps as follows : 1. Management team : We have employed the experienced senior experts to take charge of the whole management ,especially the technical management and quality management . 2. Introducing ISO management :We are aware of ISO 9001:2008 certificate . 3. QC Inspection :It is our company policy that all the finished products should be inspected by our specialized QC in every manufacture step and before each shipment Design and Detail Lofting and designing software :We have transmission power pole designing software which can help us design all kinds of steel poles ,at the same time ,the TMA and LMA are adopted by us to design the drawing accurately Advantages: The Hot Dip Galvanized Electrical Power Steel Tubular Pole plays an important role in electrical power transmission and distribution industry. In order to meet the increasingly higher demand for steel tubular pole, our company design and produce many kinds of steel tubular pole for the power transmission and distribution system. Besides, our electrical steel tubular pole have been tested and approved by the Transmission Pole Tower Testing Station. As an alternative to the traditional wood and concrete poles, our hot dip galvanized steel tubular pole could be utilize to bear the conductors and electric distribution equipment, power transmission equipment, cables, etc. our company has more than 15 years' design & manufacture experence which enable us to handle volume orders with high quality and low cost. In order to provide better service for customers, we promise to reply within 24 Working Hours and technical support by E-mail and calling service. Packaging&Shipping: * Covered by Plastic Wrap or Mat or according to client's requests. * The Loading Pcs of Each Container could be calculated according to client's specification and data Quantity(Metric Tons) 1 - 1 >1 Est. Time(days) 20 To be negotiated Manufacturing: Raw material: Q235 or Q345 in China. We get the raw material checked in our lab test room. Silicon less than2%. We have carbon and sulfur analyzer to check the elements of the steel sheet. We'll return the steel if they are unqualified. So in this way, we can control the quality of the steel poles from the first beginning. Our factory owns advanced production lines and machines including bending calibration machine, hydraulic plate shears machine, shears machine, slitting machine, 208T hydraulic straightener, etc. All insure us to produce steel poles with the best quality. After the fabrication process as cutting plate, bending, forming, automatic welding, drilling holes, we get poles checked before galvanized, hot dip galvanized and powder coating and finally we get poles checked according to client's requirements. Octagonal Hot Dip Galvanized Steel Tubular Pole Lap Joint Type Custom Painting 1

Product Description High Potential Cast Magnesium Anode / OEM AZ63C Cast Mg Anode for Cathodic Protection Cast Magnesium Anode Product Introduction: The corrosion of metal in salt or fresh water or in soil can be prevented by the use of galvanic anodes in a cathodic protection system. Magnesium anodes are used in such systems, most commonly to protect underground gas, oil and water pipelines. When the anode's cable is attached to a pipeline or other underground structure, a galvanic cell is created in which electrons flow from the anode to the structure, thereby protecting the structure. The anode corrodes instead of the structure and must be replaced after a certain period of time that depends on the type of structure that is being protected, the size and grade of anodes that are used, and the corrosivity and resistivity of the surrounding soil. In addition to pipelines, magnesium anodes are often used to protect propane, water and chemical storage tanks, areas of ships and port facilities that are not in direct contact with sea water, power plants and irrigation systems. Specifications: Standard : ASTM G-97 Chemical compositions of cast magnesium anode (%) Element High potential AZ63B AZ63C AZ63D Al <0.01 5.30-6.70 5 , .30-6.70 5.0-7.0 Zn --- 2.50-3.50 2.50-3.50 2.0-4.0 Mn 0.5-1.30 0.15-0.70 0.15-0 , .07 0.15-0.70 Si (max) 0.05 0.10 0.30 0 , .30 Cu (max) 0.02 0.02 0.05 0 , .10 Ni (max) 0.001 0.002 0.003 0.003 Fe (max) 0.03 0.005 0.005 0.005 Others each 0.05 --- -- --- Others total 0.30 0.30 0.30 0 , .30 Mg Balance Balance Balance Balance Electrochemical Properties of cast magnesium anodes Item Open-circuit Voltage Close-circuit Voltage Actual capacitance Current efficiency (-V) (-V) (A.h/g) (%) , High Potential 1.70-1.75 1.57-1.62 ≥ 1.100 ≥ 50 Low Potential (AZ63) 1.50-1.55 1. , 45-1.50 ≥ 1.105 ≥ 50 Note: Open and Close-circuit voltage is relative to Saturated Calomel Electrode (SCE) Application: The corrosion of metal in salt or fresh water or in soil can be prevented by the use of galvanic anodes in a cathodic protection system. Magnesium anodes are used in such systems, most commonly to protect underground gas, oil and water pipelines. Company Brief Introduction: We are a professional anode supplier over 16 years ,mainly supply: * Zinc anodes (ASTM B418-95 US MILL 18001K) * Al-Zn-In anodes (GAIII) * Magnesium anodes ( ASTM-G97) * High silicon cast iron anodes ( ASTM-A518-3,BS1591) Our anodes are shipped worldwide especial main to North America, Asia etc., around 5000mt per year. Our goods are regularly tested by independent third party lab in USA to keep anode continuous high quality. Our plant owns raw material resources ore, so we can supply very good price with service for you. We can also accept customized anodes with your logo according to your drawing ! Office, Workshop, Inspection Lab: High Potential Pipeline Cathodic Protection System 0 Company Principle: Our Belief: Continuous Innovation. Our Spirit: Sincerity, Unity, Dedicated, Hardworking. Our Mission: Provide most advanced products & most professional technical solution.

Product Description HVAC Thermostat , Programmable Thermostat , Room Temperature Digital Room Thermostat ISO certifications .pdf Parameter : Name: E7-L Temperature Range (°C): 0°C-40°C in 0.1°C Control Temp.Range (°C): 5°C-35°C in 0.5°C Switchable Voltage: 230 V AC; 50 Hz Switchable Current: 6 A (2 A inductive load) Programmability: Programmable Temp.Meas.Accuracy: ±1°C (at 20°C) Defrosting Temperature: +7°C Power Method: 2 x AA 1.5V Lithium batteries Switch: HEAT/OFF/COOL MODE Switch Dimensions: 130 x 80 x 28 mm Features: 1. Large LCD display with backlight ; 2. Permanent user setting retention during power loss ; 3. Can control valve and boiler at the same time; 4. Optional type of control for different heating application including room thermostat; floor thermostat or room thermostat with floor limitation; 5. Optional programming Period: 7 individual day programming with 48 separate time to select economic or comfort mode.(Every half hour as a period of time) /cancel the programming function. Packaging: 1. Inner package:Chinese/English/neutral package,special requirements based on clients. 2. Outer package:standard exporting package,special requirements based on clients. 3. One pcs per box. 4. Professional Perfomance Thermostat supplier. 5. 1 pcs in a color box, 8 pcs in a inner box, 2 inner boxes into one outer carton. 230VAC Digital Programmable HVAC Thermostat For Room 0

Original Mimaki UJF-7151 UV printer printhead M017429 Mimaki UJF-7151 Plus Printhead - M017429 This head assembly is suitable for Mimaki UJF-7151 Plus printers. This is the original Mimaki part (number M017429 replaced by MP-M025074). This head assembly includes brackets, tubes, damper and subtank. Specifications : Print Method: On-Demand piezo technology Ink Re-circulation Structure: Ink re-circulation through all channels Print Width: 53.7mm Nozzles: 636 Nozzle Resolution: 300npi Number of Lows: 2 Nozzle Spacing (Row to row distance): 4.64mm Grayscale Level: 4 levels/0,5,6,7drops Drop Volume: 57~80pL Frequency: 4.8kHz/7drops Power Supply Voltage for Driving the Head: 14~31V Power Supply Voltage for Driving Circuit: 5V, 39V Ink Type: UV-curing Size, Weight: 94.1mm(W)×26mm(D)×79mm(H), 161g Printer compatibility : Mimaki UJF-7151 Plus

Canon PF-06 Printhead - Canon's innovative printhead technology allows impressive print speeds from the new Canon TX-series, TA-series & TM-series hybrid printers. The Canon LUCIA TD & LUCIA TM five colour pigmented ink system combined with this PF-06 single printhead give better accuracy and speed than ever before for long lasting, vibrant prints. The TA Series has taken the best qualities from the advanced imagePROGRAF TX and TM Series, including the core Air Feeding System (AFS) technology, which keeps the paper flat so that the print heads can drop the ink precisely without rubbing against the paper. This means users get a higher quality, more accurate image. The Canon PF-06 fits the following Canon machines: Canon TX-2000 Printer Canon TX-3000 Printer Canon TX-4000 Printer Canon TX-2000 Dual Roll Printer Canon TX-3000 Dual Roll Printer Canon TX-4000 Dual Roll Printer Canon TX-2000 MFP Canon TX-3000 MFP Canon TX-4000 MFP Canon TM-200 Printer Canon TM-205 Printer Canon TM-200 MFP L24ei Canon TM-205 MFP L24ei Canon TM-300 Printer Canon TM-305 Printer Canon TM-300MFP L36ei Canon TM-305MFP L36ei Canon TA-20 Printer Canon TA-30 Printer GDS is a Canon Gold Partner in Graphic Arts & Canon Gold Partner in Architecture, Engineering, Construction & Manufacturing. As such we only stock and supply genuine Canon inks and we do not supply or recommend using compatible cartridges. When you buy Canon inks from GDS you can by assured of a documented supply trail and UK Canon manufacturer warranty. Description+ Additional information+ Weight 1 kg Printer Canon TA-20, Canon TA-30, Canon TM-200, Canon TM-205, Canon TM-300, Canon TM-305, Canon TX-2000, Canon TX-3000, Canon TX-4000 Manufacturer Canon Cartridge Type Printheads EAN 4549292098044

Five Star Finance Company Limited Borrow money here today at a 3% interest rate. My company offers all kinds of financial services at a 3% interest rate and our services are 100% guaranteed and risk-free. to Apply, contact company fivestarfinancecompany@gmail.com WhatSapp: +1(801)512-2040. Do you also want to be an Agent / Broker? - Investments Offer? - Do you need a Loan? - Do you seek an Insurance Coverage Loan? Intermediaries/Consultants/Brokers are welcome to bring their clients and are 100% protected. Do you need financial assistance? We can help you?. Apply now for a 3% loan. Kindly contact us for more information to procure the loan fivestarfinancecompany@gmail.com WhatSapp: +1(801)512-2040

Minimum Order: 70000

AC85-265V LED emergency downlights Product Description The Naips Led Emergency Down light provides a complete solution for LED emergency lighting. Use our Emergency Lighting Battery Pack to match different wattage of LED down lights within 3-20W. Its integral 3 hour battery replaces the conventional EM relays and battery packs with no key switches required as the system runs automatically. MODEL: NA05-SL-4 1. New Design Injection-molded Abs Housing 2. Fireproof Rechargeable 3. Non-Maintained Emergency Mode

Good quality support of Emergency LED Exit Sign Light. Surface Mount/hanging or ceiling are available. With high class acrylic Led Exit Signs available in AC85-265v emergency with elegant styling, easy installation and energy saving, long life span battery back up. Some designs we provides support battery replacement. Model: NA08-EL-31 Material: Aluminum+ Glass Glass color: Dark-green Voltage: AC85-265V Power:1W Light color: Green Emergency time: 90mins Battery: 1.2V Ni-cd 800mAh Emergency luminace:50-300cd/m2 Installation: Wall mounted or Hanging Applications: Shopping mall, Store, Building, School, etc.

100% Output Li-ion Battery Emergency Light Conversion Kit Product Description This NA02-F60 Is New Model Intergrated Led Emergency Modules can be controlled by switch on/off when power cut. This conversion kit can connect several LED bulbs, LED lamps, LED tubes or downlights in emergency for operating total not over 60W in 100% power output. The Full Power Emergency Battery Pack is suitable for converting existing light fittings to emergency operation. You no need to change the wiring. And 100% to save your electric power cost. Switch On/Off Emergency Mode DC Output: 220V Emergency time more than 3 hours Battery: 11.1V lithium ion 4400mAh Material: PC+ABS Deep discharge protection, IC control Prevent overcharging and over discharging Intergrade design. Easy install and maintain In contrast to LED drivers, the Emergency Driver For Panel is used to transform a regular panel light into an un-maintained emergency light.

This Emergency Battery Backup Led Driver is a conversion kit remote box for operating 3-70W LED luminaires in emergency mode. The conversion kit is suitable for converting existing light fittings to emergency operation. Best Emergency Driver For Panel for your option UPGRADE DESIGN 1. This NA01-H70-W3 have been improved to use Premium Lithium batteries (LiFePO4) - compared to lead acid batteries - offer significantadvantages: Safety and stability: In case of hazardous events, such ascollision or short- circuiting, this type of batteries doesn’t explode or catch fire, significantly reducing any chance of harm. It can reach 350°C to 500°C. It will be longest lasting and safety available for working. 2. Match wide range of LED lamp from 3w to 70w, Emergency time more than 3 hours 3. CB, CE, SAA Approved 4. Deep discharge protection, IC control Prevent overcharging and over discharging 5. Light weight and intergrade design. 6. Easy install and maintain

According to different production methods can be divided into hot rolled pipe, cold rolled pipe, cold drawn pipe, extrusion pipe, etc. 1.1. Hot rolled seamless stainless steel pipes are generally produced on automatic tube rolling units. The solid tube billet is inspected and cleared of surface defects, cut into the required length, centered on the perforated end face of the tube billet, and then sent to the heating furnace for heating, and perforated on the perforating machine. In the perforation at the same time constantly rotating and advancing, under the action of the roll and the head, the blank tube gradually formed inside the cavity, called the capillary tube. It is then sent to the automatic pipe mill for further rolling. Finally, the wall thickness of the whole machine is adjusted, and the sizing machine is calibrated to meet the specification requirements. It is an advanced method to produce hot rolled seamless steel pipe with continuous tube rolling unit. 1.2. If you want to obtain smaller size and better quality seamless pipes, you must use cold rolling, cold drawing or a combination of both methods. Cold rolling is usually carried out on a two-high mill, in which steel pipe is rolled in an annular pass consisting of a circular groove of variable section and a stationary conical head. Cold drawing is usually carried out in 0.5 ~ 100T single chain or double chain cold drawing machine. 1.3. The extrusion method is to place the heated billet in the closed extrusion cylinder, and the perforating rod and the extrusion rod move together, so that the extrusion part is extruded from the smaller die hole. This method can produce small diameter steel pipe. This kind of steel pipe can be divided into stainless steel seamless steel pipe and stainless steel welded steel pipe (welded pipe) two categories, according to the manufacturing process can be different For: hot rolling, extrusion, cold drawing and cold rolling these basic types, according to the section shape can be divided into round pipe and shaped pipe, widely used is the circular steel pipe, but there are also some square, rectangular, semicircular, hexagonal, equilateral triangle, octagonal shaped stainless steel pipe. For the steel pipe under fluid pressure to carry out hydraulic test to check its pressure capacity and quality, under the specified pressure does not leak, wet or expansion to qualify, some steel pipe also according to the standard or demander requirements for flange test, flaring test, flattening test. Seamless stainless steel pipe, also known as stainless steel seamless pipe, is made of steel ingot or solid tube billet perforated into wool tube, and then made of hot rolling, cold rolling or cold dialing. The specification of seamless steel pipe is expressed by the outer diameter * the thickness of the wall in millimeters

Minimum Order: 1 bags