Offers to Sell

The main production lines of pet flakes friction washer are conveyor belt, off- label machine, sorting table, crusher, hot water steamer, screw elevator, high- speed friction cleaning machine, single (double) screw rinsing machine, centrifugal dehydrator, cyclone silo, electric control Cabinets, etc. Features of pet bottle recycling washing machine The quality of the bottle flakes cleaned by the company's production equipment is similar to that of the new material, and high-end products such as POY filaments, staple fibers, preforms, PET packing tapes, and sheets can be directly processed without additional processing. As one of the most professional plastic recycling equipment manufacturers and pet flakes washing plant , we provide plastic recycling machine in china, china pet bottle washing line, pet bottle crushing and washing line, recycled plastic extrusion machine, etc. Want to know more, contact us.

According to the statistics of China Urban Environmental Sanitation Association, my country produces nearly 1 billion tons of garbage every year, including about 400 million tons of domestic waste, about 500 million tons of construction waste, and about 10 million tons of kitchen waste. The quantity is one of the best in the world. With the acceleration of my country's urbanization process and the improvement of people's living standards, urban domestic waste is still increasing at a rate of about 5%-8% per year. Garbage siege is ringing alarm bells for Chinese cities. Features of Mulch And Greenhouse PE Film Washing Machine The impact of domestic waste and waste plastics on the ecological environment cannot be ignored, mainly because of its refractory degradability, which causes a serious problem of "white pollution", which has attracted great attention from the environmental protection department. Domestic waste plastics in domestic waste are mostly classified by complete sets of sorting equipment, organic matter, inorganic matter and waste plastics. However, due to the complex composition of waste plastics, it is very difficult to use, and many processing enterprises still use incineration and landfill, causing secondary pollution to the environment. As a professional plastic recycling machine company, and pe film washing line manufacturer, we provide hdpe washing line, pe pp film washing line, ldpe film washing line, pe film washing machine, pe film washing line, waste plastic recycling machine, waste plastic extrusion machine, etc. Want to know more, contact us.

The dispersion kneader is referred to as an internal mixer. In order to adapt to the application of mixed waste plastics, a waste plastic internal mixer was developed. Internal mixer is a kind of machine that is equipped with a pair of rotors with a specific shape and rotates relatively, and intermittently masticates and kneads polymer materials in a closed state with adjustable temperature and pressure. , Rotor sealing device, feeding and pressing device, unloading device, transmission device and frame and other parts. As one of the most professional dispersion kneader manufacturers, we provide plastic recycling machine in china, pp pe film washing system, textile recycling machine, etc. Want to know more, contact us.

Plastic building brick mould can be used as brick molds; if you are making houses, you must have a series of molds. Application of Plastic Brick Mould Good for house construction. As one of the most professional plastic recycling machine manufacturers, we provide plastic recycling machine china, pp pe film washing system, pe film granulator, fabric recycling machine, etc. Want to know more, contact us.

One-step fabric waste recycling machine is extrusion molding equipment together with waste plastics and auxiliaries to directly make trays, manhole covers, flower pots and other products. Features of One-Step non woven fabric recycling machine According to incomplete statistics, more than 1 billion tons of used clothes are dumped into landfills worldwide every year, generating 2 million tons of carbon dioxide emissions every year. What is even more shocking is that by 2030, the impact of old clothes on climate warming will increase to 49%, and climate warming will make more and more polar bears homeless and even extinct. What can we do for polar bears in symbiosis on this blue planet? A 2008 study conducted by the Bureau of International Recycling (BIR) at the University of Copenhagen in Sweden concluded that every kilogram of old clothing recycled can reduce carbon dioxide emissions by 3.6 kilograms. This also means that for every additional piece of old clothing recycled, we can slow down some more of the rate of global warming, and we have more hope of preserving a glacier for polar bears. In view of this, our company has invested a lot of manpower and material resources in the research of recycling equipment. A complete set of profile extrusion equipment has been developed, and the waste spinning and granulation are added to the one-step extrusion molding equipment together with waste plastics and auxiliaries to directly make trays, manhole covers, flower pots and other products. As one of the most professional waste plastic recycling machine suppliers, we provide woolen cotton yarn fabric recycling machine, wool fabric recycling machine, polyester fabric recycling machine, plastic recycling extrusion machine, etc. Want to know fabric recycling machine price or more, contact us.

The equipment we have developed includes: one-step extrusion molding equipment for mixed waste plastic films; two-step extrusion molding equipment for mixed waste plastics; co-directional flat one-step extrusion molding equipment; single-station and double-station extrusion molding equipment for higher production efficiency. Plastic recycling molding machine solves the worldwide problem that mixed plastics waste is difficult to be reused, and truly enables mixed waste plastics to achieve green recycling and high-value utilization. We can also formulate sustainable anti-expansion solutions and tailor-made equipment according to customers' raw materials and requirements. Types of Mixed Plastic Recycling Extrusion & Injection Molding Machine Double-Station One-Step Recycling Plastic Extrusion Molding Machine The fully automatic one-step film extrusion molding equipment is our company's patented product. The Difference Between Injection Molding And Extrusion Molding 1 / 2 The difference between extrusion molding and injection molding Extrusion molding: The material is double-mixed, dispersed and plasticized through a special co-rotating cone, and the plasticized plastic is extruded into the storage tank through reversing. When the required amount is reached, the plastic is extruded into the mold. When the mold has a certain space, after the material is injected, it is pressed and cooled to make the products we need. Injection molding process This production method is to directly inject the plastic into a fixed mold after plasticizing, and the mold is fixed and then cooled to make the product we need. For example: trays, plastic manhole covers, plastic flower pots, etc. How Does Mixed Plastic Recycling Extrusion & Injection Molding Machine Work? Plastic pollution has become one of the most pressing environmental concerns, as the rapidly growing production of single-use plastic products outstrips the world's ability to deal with them. Plastic pollution is most pronounced in developing countries in Asia and Africa, where waste collection systems are often inefficient or non-existent. But developed countries, especially those with low recycling rates, also struggle to properly collect waste plastic. To this end, we have developed mixed waste plastic cleaning equipment and granulation equipment for processing, and then use "mixed waste plastic extrusion molding equipment" to make the products we need, trays, manhole covers, flower pots and other products. Through the design of the barrel and the screw, the main difficulties of mixing, dispersing, plasticizing and mixing mixed waste plastics can be solved; Through technical research, the measurement problem of products has been solved; Through the improvement of the storage system, the problem of insufficient injection force has been solved; Realize intelligence through automatic design. As a professional plastic recycling machine factory, we provide plastic recycling machine in china, waste plastic recycling machine, extruding recycled plastic, extrusion recycling, recycled plastic molding machine, recycled plastic extrusion machine, waste plastic extrusion machine, recycled plastic extrusion, etc. Want to know more, contact us.

Auto recloser relay control higher voltages or currents by using lower voltages or currents. When a certain voltage or current is applied to both ends of the electromagnetic relay coil, the magnetic flux generated by the coil passes through the magnetic circuit composed of the iron core, the yoke, the armature and the working air gap of the magnetic circuit. Under the action of the magnetic field, the armature is attracted to the pole face of the iron core. Therefore, the normally closed contact of the contact is pushed to be disconnected, and the normally open contact is closed. When the voltage or current at both ends of the coil is less than a certain value, and the mechanical reaction force is greater than the electromagnetic attraction force, the armature will return to the initial state, the normally open contact is disconnected and normally closed contact is on. How To Test Auto Relays？ (1) A simple method for judging the working performance of the relay. Turn on the ignition switch, and then use your ear or stethoscope to listen to the sound of the control relay, or feel the vibration of the relay with your hand. If there is vibration, then the relay is working well, the electrical appliance does not work due to other reasons. Otherwise, the relay is not working properly. You can also unplug the relay for testing, for example, if the air conditioner compressor does not work, you can start the engine, turn on the blower switch and the air conditioner switch. Then unplug the connector of the air conditioner compressor relay to judge. If the sound of the relay action can be heard, the engine speed drops significantly when the relay is unplugged, and the engine speed rises when the relay is inserted, it means that the air conditioner compressor relay and its control circuit are normal. (2) Common failures of relays. Common failure phenomena of relays include coil burnout, inter-turn short circuit or insulation aging, contact ablation, thermal decay, and inability to adjust the initial operating current. ①The relay coil is burnt out. In order to prevent this from happening, if the temperature may exceed 80°C during repair, maintenance and electric welding, the temperature-sensitive relays and electronic control units should be removed. ② Contact ablation. For example, vehicle with 491Q-ME engine, the relay of the air conditioner condenser fan is just below the glass cleaning spray pipe. If the spray pipe is broken, the cleaning fluid will leak to the relay, making the relay normally open contact is corroded and cannot be disconnected, which will lead to the failure of the air conditioner condenser fan to keep running. Therefore, water should be strictly prevented from entering the relay. (3) Try to reduce the contact resistance of the relay contact The contact resistance existing between the contacts of the automotive relay is mainly composed of shrinkage resistance and surface film resistance. The contact resistance of the contact is related to the contact form, material properties and surface processing of the contact. It can be seen that to reduce the contact resistance of the relay contacts, under the condition of a certain contact pressure, it can be started by improving the contact state and improving the contact material. (4) Poor grounding of the ECU may affect the normal operation of the relay As one of the most professional car spares suppliers, we provide automobile air filter, car spares and parts, auto off relay, auto power relay, auto relay block, auto relay switch, pencil coil, etc. For more information, please feel free to contact us!

Minimum Order: 1 bags

Sensor for automotive is the input device of automotive computer system. It converts information of various working conditions, such as vehicle speed, temperature of various media, engine operating conditions, etc., into electrical signals and sends them to the computer, so that the engine is in the best working state. As the information source of electric control system, automotive sensor is not only the key component of electric control system, but also one of the core contents in the field of automotive electric technology. Automobile sensors can measure and control various information such as temperature, pressure, position, speed, acceleration and vibration in real time and accurately. Automotive sensors from MAPMS have characteristics. Strong adaptability and resistance to harsh environment. It also has good sealing, moisture resistance, corrosion resistance and so on. Strong anti-interference ability. High stability and reliability. High cost performance, suitable for mass production. It converts various operating conditions of the automotive, such as vehicle speed, temperature of various media, engine operating conditions, etc., into electrical signals and sends them to the computer so that the engine is working at its best status. How Does The auto sensors Work? There are various sensors on vehicle. They constantly detect the working condition information of the vehicle, convert the electric energy into signals, and transmit these signals to the ECU in real time. After the ECU makes the corresponding decision and processing, then outputs the signal to the corresponding actuator. After receiving the output signal, the actuator performs the corresponding action to realize a certain predetermined function. Each sensor performs its duties and cooperates with each other, which plays an important role in the operation of the vehicle. Sensors used in the engine control system are the core of all auto sensor car, including temperature sensors, pressure sensors, position and speed sensors, air flow sensors, gas concentration sensors and knock sensors to help ECU can accurately control the working condition of the engine to improve the power of the engine, reduce fuel consumption, reduce exhaust emission and carry out fault detection. As one of the most professional auto spares suppliers, we provide industry auto parts, auto spares sale, etc. For car sensor cost or more information, please feel free to contact us!

Minimum Order: 1 bags

Automobile fuel supply system is classified according to fuel supply mode: carburetor engine, EFI engine and in cylinder direct injection engine, supply to the cylinders, and make it ignite, burn and expand to do work near the end of compression. Finally, the fuel supply system should also discharge the combustion product exhaust gas into the air. Each part must work flawlessly to achieve expected vehicle performance and reliability. Car fuel supply system has been widely used in automobiles because of its simple structure, convenient use and low cost. However, the main disadvantage of carburetor engine is that the inflation and mixture distribution are not ideal. It has a certain adverse impact on the improvement of engine power, economy and emission. Therefore, modern cars are basically not used. At present, the mainstream is EFI engine and in cylinder direct injection engine. EFI engine uses electronic control device to control the fuel supply process of the engine. According to the number of injectors, EFI engine can be divided into multi-point injection and single point injection. At present, multi-point injection is mostly used. The main principle of multipoint EFI is that the injection process of gasoline fuel is in the intake manifold. If the injector is installed on the intake pipe of each cylinder, gasoline can be injected into multiple cylinders, which forms multipoint injection. The cost of gasoline injection is not only lower, but also less carbon deposition. How Does The Automotive Fuel System Parts Work? The fuel pump sucks the fuel out of the fuel tank, filters out the impurities through the fuel filters and enters the low-pressure fuel chamber of the fuel injection pump. After increasing the fuel pressure, fuel will be transmitted to the fuel injector through the high-pressure fuel pipe. When the fuel pressure reaches a certain value, the fuel injector sprays the fuel into the combustion chamber in the form of mist to form mixed gas and burn. After working, the waste gas will be discharged into the atmosphere through the exhaust device. The task of fuel supply system is to prepare a certain amount and concentration of combustible mixture according to the requirements of various working conditions of the fuel engine, supply it to the cylinder, and make it ignite, burn and expand to do work near the end of compression. Finally, the supply system should also discharge the combustion product - exhaust gas into the atmosphere. How To Wire Automobile Fuel System Parts? Components of automotive fuel supply system consist of fuel tank, fuel pipe, fuel pump, fuel filter, air filter, fuel pressure regulator, fuel injector, intake manifold, exhaust manifold, etc. The task of the fuel supply system of fuel engine is to pump the fuel out of the fuel tank through the fuel pump, via fuel filter which filters the impurities and water in the fuel, then enters the fabricated fuel rail. The engine ECU sends fuel injection signals to the fuel injection nozzle according to the output signals of various sensors of the engine, ejects the fuel from the fuel injectors at a certain pressure, mixes it with the clean air obtained through the air filter in the intake manifold in a certain proportion according to the requirements of various working conditions of the engine, finally enters the cylinder, compresses, works and exhausts in the cylinder, to generate engine power. As one of the most professional car spares suppliers, we provide industry auto parts, auto spares sale, etc. For more information, please feel free to contact us!

Minimum Order: 1 bags

The car air filter commonly used in passenger fuel vehicle engines mainly have paper air filter and polyurethane air filter. Paper air filters are made of microporous filter paper treated with resin. The filter paper is porous, loose and folded. They have certain mechanical strength and water resistance with advantages of high filtration efficiency, simple structure, light weight, low cost and convenient maintenance. They are most widely used as vehicle air filters at present. Polyurethane car filter are made of soft, porous and spongy polyurethane with strong adsorption capacity. They have the same advantages of paper air filters, but also have low mechanical strength. What Are the Symptoms of a Bad Air Filters? The auto air filters is a device for removing particulate impurities in the air. If the air contains dust and other impurities, will aggravate the wear of engine parts, so air filter with good performance must be installed into the vehicle. The main requirements of the air filter are high filtration efficiency, low flow resistance and continuous use for a long time without frequent maintenance. In case of damage or blockage, the following phenomena will occur. Acceleration performance decreases and fuel consumption increases. Once the filter element is blocked, there is too much dust and the aperture of the filter paper is blocked, will hinder the passage of air. Then the air intake rate will decrease, the air flow will decrease, and there is not enough air support when the engine burns. Even if the accelerator is pressed deeply, the speed still can not come up, there will be insufficient power and the driving fuel consumption will increase. Moreover, under the strong negative pressure (intake suction) of the engine, the dust, impurities and particles outside the filter element will break through the filter paper and directly enter the cylinder to participate in combustion, even lead to the breakage and rupture of the filter paper. The engine emits black smoke. If the automobile air filter is damaged or not replaced and cleaned for a long time, the dust will directly enter the engine and pass through the throttle. At this time, the particles in the air are like grinding sand, which will cause wear to the throttle. After the throttle is worn, it will sink, reduce the compression ratio and air leakage, resulting in the reduction of engine cylinder pressure, hard to start and low combustion efficiency. The cylinder burns insufficiently, the exhaust pipe emits black smoke and presents a divergent shape, and the air flow has no impulse. As one of the most professional car spares suppliers, we provide automobile air filter, auto spares sale, pencil coil, etc. For air filter car cost or more information, please feel free to contact us!

Minimum Order: 1 bags

Car air conditioning system is a device that realizes cooling, heating, ventilation and air purification of the air in the vehicle. It can provide a comfortable driving environment for driver and passengers, especially reduce the driver's fatigue strength, and improve driving safety. The air conditioning unit has become one of the indicators to measure whether the vehicle is fully functional. Modern vehicle air conditioners have four functions, any of which are designed to make driver and passengers comfortable. The air conditioner can control the temperature in the cabin, both heating and cooling the air, to make the cabin has comfortable temperature. The air conditioner can discharge the moisture in the air. Dry air absorbs human sweat and creat a more comfortable environment. The air conditioner has functions of inhale fresh air and ventilation. The air conditioner can filter the air to remove dust and pollen. How Does The Air Conditioning System (A/C) Work? Automotive air conditioning is mainly composed of refrigeration system, heating system, ventilation and air purification system and control system. The principle of automotive air conditioning has four sections. A, The compressor sucks the low-temperature and low-pressure refrigerant gas at the outlet of the evaporator, and compresses it into high-temperature and high-pressure gas and discharges from compressor. B, The high-temperature and high-pressure refrigerant gas enters the condenser and condenses into a liquid, discharges a large amount of heat. C, The refrigerant liquid with high temperature and high pressure increases in volume after passing through the expansion device, the pressure and temperature drop sharply, then discharged from the expansion device in the form of a mist. D, The mist-like refrigerant liquid entering the evaporator, the boiling point of the refrigerant is much lower than the temperature in the evaporator, and the refrigerant liquid evaporates into a gas. Diagram of Air Conditioning System (A/C) The automotive air conditioning refrigeration system consists of a compressor, a condenser, a liquid receiver dryer, an expansion valve, an evaporator and a blower. The components are connected by copper pipes and high-pressure rubber pipes to form a closed system. When the refrigeration system works, the refrigerant circulates in this closed system in different states. As one of the most professional auto spares suppliers, we provide car air conditioner replacement, car air conditioner gas, car ac unit, car ignition components, car auto spare parts, etc. For car ac unit price or more information, please feel free to contact us!

Minimum Order: 1 bags

Barrel bungs plastic bung is G2 and G3/4'' plug type with ISO-228 thread, can well suit into drum flange on 55 gallon steel drums. It is a substitute for zinc plated drum plug in some cases. Whatever the material is, the bungs are aiming at reducing the risk of spillage and keeping the contents safe The included 2'' and 3/4'' bung fittings make filling and dispensing easy and convenient, the plug wrench is designed to help to screw in and out of the bung fittings. Details of Steel Drum Plastic Bung 1 The raw mateiral of the steel drum plastic bung is made of new polypropylene and selected recycled polypropylene, which maxiumize the useage of the commericals and also keep the final bung in good properties. 2 Not even the most critical thread parts follow the standard, other aspects of the plastic bung is also designed to be similiar to the common types in global market, which enable to well replace other plastic bungs. 3 The gasket selection is based on the containers' contents, the common types are EPDM, NBR and PE gasket applied to the steel drum plastic bung, differenciate from temperature tolerance, chemical resistance. Specification of Steel Drum Plastic Bung Size 2 Inch and 3/4 Inch Material Polypropylene Thread Standard ISO-228 Gasket EPDM, Black Buna, PE Carton Quantity 250 Pieces,1000 Pieces Pallet Quantity 11,250 Pieces, 45,000 Pieces As a professional cap seal manufacturer, we provide barrel fittings, drum closure, etc. For more information, please feel free to contact us!

These steel drum flange and plug come available in zinc plated and phenolic lacquered styles, preventing from various corrosive contents. Closure is equipped with well-formulated EPDM, NBR or PE gasket, the different materials make it perform well under different filling conditions. Dual gasket system is another common choice in European area as two combined washers can seal with better security. The octagonal flange is supposed to riveted on metal drum lid providing a seal base for drum plug to be torqued on, those 2'' and 3/4'' set make up an universal closing system for standard close head drum. It is necessary to have a well- designed paint cap covering on drum lid mouth, preventing the inner side of drum from spraying paints contamination. Secure your drum or barrel during packaging, storage and transport with our steel drum closure! Types of steel drum caps Zinc Plated Drum Flange Zinc Plated Drum Plug Zinc Plated Drum Plug Read More  Lacquered Drum Flange Lacquered Drum Plug Drum Paint Cap  Features of Steel Drum Closure Zinc Plated Drum Flange Octagon zinc plated drum flange is the key base for steel, plastic, nylon plug screwing in. Zinc Plated Drum Plug Fitted with EPDM, Buna or PE gasket, drum plug plays the initial guard ensuring fillings integrity. Lacquered Drum Flange Painted drum flange is selected for drum while there is more corrosive content within. Lacquered Drum Plug G2 and G3/4 drum plug treated with lacquer, is often chosen for special chemicals or food grade products. Drum Paint Cap Avoid of interior contamination, drum paint caps are efficient protective caps during drum painting process. How To Use Steel Drum Closure? Drum flange needs to be riveted onto drum top by flange insertion die before using. It forms a base for drum plug to screw in after drum flange riveted. Customers could choose steel drum plug, plastic drum plug or nylon plug based on contents in the drum. Appropriate torque is essential while screwing drum plug, excess or lack of torque will lead to leaking risks of the container. After both drum flange and plug are properly installed, it forms a sealing system for drum. Flange riveting is crucial in terms of final sealing results. Regular maintenance or replacement of insertion die is necessary to keep riveting quality. Key parameters, including insertion die abrasion and flange height after riveting, need to be checked if problems occur. As a professional cap seal company, we provide drum bung fittings, drum closure, steel drum bung, metal bung, metal drum plugs etc. For more information, please feel free to contact us!

The airbag sensor is the input device of control signal in the SRS system. When the vehicle happens to collides, the airbag sensor detects the intensity signal of the vehicle collision, and inputs the signal into the airbag computer. The airbag computer determines whether to detonate the inflatable element to inflate the airbag according to the signal of the airbag crash sensor. How To Test airbag front sensor? 1) Symptoms of airbag system failure are difficult to diagnose, so diagnostic codes are the most important source of information for troubleshooting. Always check the diagnostic codes before disconnecting the battery. 2) Disconnect the ignition switch during inspection. If the vehicle allows to remove the negative electrode of the battery, it is better to disconnect the power supply. It should be started after removing the negative electrode for 90s or longer. Because the airbag system is equipped with a backup power supply, the airbag may still deploy within 90 seconds after removing the negative terminal of the battery. 3) Even if only a minor collision occurs and the airbags are not deployed, the front airbag pressure sensor and steering wheel cushion should be checked. 4) Do not expose the front airbag impact sensor, center airbag sensor assembly and steering wheel pad directly to hot air and flames. 5) When testing the circuit, a high-impedance multimeter should be used for measurement. 6) The parts of the airbag are attached with instruction labels, and the listed precautions should be strictly followed during operation. 7) After pulling out the airbag wiring plug, use a small copper wire to short the airbag connector. 8) Do not measure the resistance of the detonator tube of the airbag inflation element, so as not to cause the airbag system to explode by mistake. The method of decomposing the inspection parts should be adopted first, and then searching step by step. 9) The airbag system is a very sensitive device. A little carelessness during inspection may detonate the airbag and cause unnecessary losses. 10)The wire harness and connector of the airbag system are generally covered with a special color sleeve, which is different from other system wire harnesses. Do not damage these bushings during inspection. As a professional auto spare parts supplier, we provide car ignition components, car ignition coil, etc. For impact sensor price or more information, please feel free to contact us!

Minimum Order: 1 bags