Offers to Sell

QJ Submersible PUMP General Description The QJ submersible pump is mainly used for carrying water from a deep well and boosting and is widely used in farmland irrigation, water draining in urban and rural areas and mines and industrial enterprises and water conservancy works including reservoir, fountain, cooling system and spa etc. The main features are as follows: With easy to use, easy installation, easy maintenance, environmental protection etc. Advantages, the electric diving pump which collects the motor and water pump could work in the water and it is convenient to use and repair. Submersible Pump Manufacturers We are a professional manufacturer of submersible pumps in China. In addition to water pumps, we also supply various slurry pumps, gravel pumps, desulfurization pumps, etc. According to different requests, we could provide products with different materials like stainless steel casting, stainless press-welding, bronze casting, plain iron casting, corrosion resistant special material casting. The pump must be strict with outside diameter, so the situations such as motor seal leaks and water pollution will not occur. Specifications Size (discharge): 4" to 16" Capacity: 2-500m3/hr Head: 10m-500 m Housepower: 0.75-450kw Material: Cast Iron, Bronze, Stainless steel etc AIER® QJ Submersible Pump Conditions Of Usage ①Power: 380V/3-phase AC, 50Hz ②Water quality: A. The temperature of water is below 20℃(high temperature resistance 80℃) B. The solid content is less than 0.01% (depends on the quality) C. PH 6.5-8.5 D. The content of hydrogen sulfide is less than 1.15mg/l E. The content of oxide ion is less than 400mg/l ③The inner part of the submersible motor must be full of clean water and submersible pump must sefely submerge to work. ④Mounting depth shall not exceed 20% of water pump rated head and well face must be smooth and straight. Main Features 1. The motor is wet submersible motor. The motor chamber must be filled with clean water which is used for cooling motor and lubricating bearing. The voltage regulating film on the base or motor is used for adjusting pressure difference and dilation of water in the inner part of motor caused by motor temperate changes. 2. In order to prevent the sand grains from a well from enter into the inner part of motor, upper shall extension is installed two seals oils which are installed backward and one sand off ring is installed. 3. To prevent water pump shaft from jumping, water pump shaft and motor shaft are connected by coupling and a thrust bearing should be installed in the under parts of motor. 4. The water lubricates the motor and water pump bearing. 5. The submersible motor winding wires are used for the stator winding. So it insulates well 6. The centrifugal impeller and vertical blower inlet casing are used for water pump and the structure is simple. Construction Diagram QJ submersible pump mainly consists of feed point, water pump shaft, impeller, blower inlet casing, rubber bearing, check valve (option) etc. The submersible motor consists of base, voltage regulating film, thrust bearing, thrust disc, lower guide bearing block, stator, stator winding, rotor, upper guide, bearing block, sand off ring, outlet cable, etc.

ZJQ Submersible Slurry Pump General Introduction Aier® ZJQ submersible slurry pump is a kind of hydraulic machinery, the motor and the pump of which are coaxially submerged in medium to work. The wet parts of the pump are made from high alloy wear-resistant material, so the pump has good wear resistance and large flowing passage. It is applicable for conveying medium such as sand, sludge, ore slurry, coal slurry, sand, stones containing big solid particles. We have a full range of high quality submersible slurry pumps for dewatering, de-friction, abrasive media with high solids content (e.g. sand) in quarries and mining. The user-friendly design and ease of use of submersible mortar pumps make them the first choice for submersible pumps. We have Slurry Pump for Sale. SPEFICATIONS Size: 50-400mm Capacity: 10-2000m3/h Head: 8-80m Max.particles: 60mm Temperature Range: ≤80°C Materials: High chrome alloy, Cast iron, SS304, SS316L etc Aier® ZJQ Submersible Slurry Pump Design Features 1. Vertical, Centrifugal, Submersible pump design. 2. Besides the main impeller, there is the agitation impeller which can agitate the sludge deposited on the water bottom into turbulent flow and pump the sludge out. 3. The wet parts such as the impeller and the agitation impeller are made from high-hardness high chromium cast steel, have wear resistance, corrosion resistance and strong drainage capacity, and allow big solid particles to pass. 4. The motor is submerged in water, is not limited by suction stroke, and has high sludge suction rate and thorough desilting. 5. The integral device is simplified, needs no auxiliary stirrer device or ejector device, and has simple and convenient operation and low total investment of the unit. 6. The agitation impeller directly approaches the depositional surface, and controls the concentration through submerged depth. Under the condition of large medium proportion, an auxiliary device can be arranged to increase the concentration of the medium. How to choose a suitable slurry pump? The following can help you understand the pump specifications so that you need to take into account the size, strength, volume, and routine of the submersible pump. If you don't understand anything, you can contact us, we will have a professionals to solve it. More information please click here.

Product Description 300ml Ball Shaped Plastic Pump Bottle For Shampoo Gel Bottle Cosmetic Packaging ITEM Value Item Name 300ml Ball Shaped Plastic Pump Bottle For Shampoo Gel Bottle Cosmetic Packaging Product name 300ml Square Shape Plastic Pump Bottle KEY Words Plastic Pump Bottle Place of Origin CHINA Brand Name LESOPACK odel number LS0144 Usage Lotion/Makeup packaging Bottle Capacity 300ml OEM/ODM Accepatable Color Clear Cap type lotion pump Sample Free sample but You need to pay for shipping Shape Ball shape Body Material PET plastic Leadtime 30-35 DAYS MOQ 10000 Pcs Feature The spherical shape, coupled with an excellent lotion pump, will give you a good use experience. The bottle is transparent, so you can see the volume of cosmetics inside. And you can print the pattern or logo you want on the bottle We can provide free samples, but you need to pay for the freight Silkscreen Pump Cosmetic Bottles 300ml PET Pump Bottle For Shampoo 0 Silkscreen Pump Cosmetic Bottles 300ml PET Pump Bottle For Shampoo 1 Silkscreen Pump Cosmetic Bottles 300ml PET Pump Bottle For Shampoo 2

Beigquist Gap Pad Ultra VO Soft is the first chioce for automotive electroncis thermal management to many thermal management engineers. Most of Chinese suppliers can’t provide alternative except GLPOLY. Bergquist Gap Pad Ultra VO Soft has an extreme low hardness of Shore00 10, providing excellent compression. Many counterparts said they can provide alternative with similar thermal performance or electrical properties, but the most important features of low hardness and high compression will not be contrasted. Siemens engineer found us and asked ”Can you provide an alternative to Bergquist Gap Pad Ultra VO Soft, with same or better thermal performance, compression and thermal resistance?” . Actually, we had been developing a thermal pad which is with similar performance to Bergquist Gap Pad Ultra VO Soft, and we were almost there. So we told customer the truth”We are developing a similar product now, and we are going to complete it in half a month.”. Customer wish to wait for final test report, because the didn’t find a proper product yet. Half a month later, we finished the samples as expected. When I sent them the samples, I can feel they don’t value the samples. But after they finished the test, they were surprised, hardness of Shore00 10, compression of 90% and thermal resistance of 0.35℃in2/W…, thermal and physical properties were as good as Gap Pad Ultra VO Soft’s. “We had tested dozens of samples, your product is the best, also it’s only one that met our requirements.” GLPOLY XK-P10F is designed for auto eletronics with high performance, low thermal resistance. It provides low hardness and compression, optimizing interface contact and heat transfer. GLPOLY thermal management materials have been used in new energy vehicle battery pack. GLPOLY help keep your devices performing stable.

Minimum Order: 10 long tons

GLPOLY launched a complete portfolio of thermal interface materials including thermal gap pad,two-part thermal gap filler and two-part thermally conductive structural epoxy adhesive. In recent years, structure of battery pack changes a lot from module to“cell to pack”for increasing energy density. Two-part thermally conductive expoy adhesive is desgined optimize thermal management of “cell to pack” battery pack. This Oct., we received an enquiry from Toyota Tsusho, customer consulted us about a thermally conductive adhesive for “cell to pack” battery pack, requesting a thermal conductivity of 2.0W/mK and a shear bonding strength of 8MPa. GLPOLY thermally conductive adhesive XK-D20 is exactly what they need. The key characteristics of XK-D20 were verified by aging test for 1000hours, like theraml conductivity, tensile strength, shear bonding strength etc. “It seems like that the data sytisfys our design requirements, can we apply for samples for testing?” Customer asked. We provided samples for customer testing in their facility. Reliability test will last for 3 months, we were waiting for test result, we’ll update the information once we get it. GLPOLY thermally conductive adhesive provides benefits: 1.High bonding strength 8MPa, thermal conductivity 2.0W/mK; 2.Deflects under low pressure, accommodates a variety of gap thickness 3.Compatuble with volume, automated dispense process GLPOLY has launched a series of thermally conductive epoxy adhesive with thermal conductivity from 1.0W/mK to 3.0W/mK. Automated production lines were introduced to keep consystance of product. GLPOLY thermally conductive adhesives has been applied in two car-makers for trial already. GLPOLY is a prestigious thermal interface materials manufacturer in China, providing thermal interface materials for many top-class client such as dJI, Sokon Industrial Group, GAC NE Automotive, NIO Automotive and Welling Motor. GLPOLY thermal interface materials help design thermal management solution flexibly and design tomorrow’s breakthroughs.

Minimum Order: 10 long tons

GLPOLY thermal gap pad XK-P60-PUUTY is the only one that can substitute for Laird Tflex HD700 with high thermal performance and high compression. You will find that a lot of suppliers said they can provide substitute for Laird Tflex HD700 because our product provides the same thermal conductivity. Is it true? When you review the datasheet or you know even just a little about thermal gap pad, you can find that thermal conductivity is not the most important, it does not meam thermal cnductivity is not vital, but compared to the products which is with similar thermal performance, Laird Tflex HD700 provides higher compression and conformability. With benchmark of Tflex HD700, GLPOLY released XK-P60-PUTTY with high performance and compression as a perfect substitute for Tflex HD700. A customer searched us from internet and asked “can you really provide a perfect alternative part to Laird Tflex HD700 or just provide a similar product”. “Perfect alternative with thermal and physical properties, test result will show you what it really is”. We provided a XK-P60-PUTTY in 1.5mm thick after customer gave me application information of power and gap size. The test last for two weeks, customer was satisfied with result when test was finished. Customer told me that they bought a Laird Tflex HD700 from electronic material supplier on internet while he took samples from me for comparing. The temperature is 65 degree when performing with Tflex HD700, it was good, but GLPOLY thermal gap pad was better, the temperature was maintained under 60 degree. The chief engineer sent me a message, just one word ”excellent”. GLPOLY thermal gap pad XK-P60-PUTTY is high performance, high compression gap filling material with thermal conductivity of 6.0W/mK. It provides high deflection under low compressive forces, decreasing stress on component and avoiding component failures. GLPOLY is qualified partner to Huawei, ZTE and DJI, also GLPOLY thermal materials have been applied in new energy electric vehicle. GLPOLY is committed to delivering advanced thermal management solutions for top class clients.

Minimum Order: 10 long tons

Three years ago, thermal pad was a significant role, predominately in thermal management of EVs battery pack. With the advancement of EVs battery technologies, trend to shift away from thermal gap pad to thermal gap filler, providing a more closer contact between cells or cell and heat sink, and thermally conductive structural adhesive is the best in gap filler family. GLPOLY is the first one in China to develop thermally conductive structural adhesive for “cell to pack” battery pack in a new technology—modified epoxy which differ from existing PU technology. Consequently, we received many queries from engineers about properties of thermally conductive structural adhesives. Here I sorted out some information for your reference. Q: What’s the linkage between bond line thickness and shear bond strength? A: In practical application of “cell to pack” battery, there is no inevitable linkage between these two properties. Q: Shall the bonding strength vary with Al substrates? A: No matter Al3003, Al6063 or Al1030, the Al content is greater than 97%. It depends on the Hydrogen bond between crosslinker and metal atom. Effect affected by other factors is less than 3% which is within the range of tolerance. GLPOLY has full set of Al3003 fixtures for validating. Q: What factors shall affect shear bond strength? A: 1) Bonding strength decreases a lot if the surface of aluminum is oxidized to alumina; 2) Roughness. The rougher the surface, the greater the bonding strength; 3) Modifier applied on the surface. Depending on specific conditions. Q: Why not mark value of butt-joint bonding strength? A: A joint made by fastening ends together without overlapping. There is no need to test it because no butt joint happened between cell and water- cooling plate. Q: Why is it recommended to remove insulation painting? A: Painting increases thermal resistance. And in this case, it shows bonding strength between thermally conductive structural adhesive and painting, not adhesive and water-cooling plate. Furthermore, GLPOLY thermally conductive structural adhesive has electrical insulation. Q: Are contact thermal resistance the same between different substrates? For example, PET and Al? A: Both interface thermal resistance of PET and Al are between 0.000178~0.000679, but the contact thermal resistance is hard to test. our specification comforms to the result of nearly 300 regression tests. The contact thermal resistance is negligible due to extremely low value. By extension, the above conclusion is true in the application of soft pads. So it is true for liquid thermally conductive structural adhesive if there is no air bubble or water film. If you have any other question, please feel free to contact GLPOLY for detail.

Minimum Order: 100

GLPOLY thermal gel is non-dry out, non drip off, extending service life of devices and defeating 95% of competitors. Most of competitive products are similar to thermal silicone grease with a short service life, one or two years. Rivals’ thermal gel will volatilize and cure, causing thermal conducting to fail. GLPOLY thermal gel features ultra low thermal resistance, non-cure, non-drip off, just few of thermal management materials suppliers can make it. this is not bragging, it is truth. A robot design company found me and consulted about thermal interface materials with thermal conductivity of 5.0W/mK or higher and 5-year service life. As precise devices require high thermal performance and paste materials provide higher performance than solid materials, we recommended XK-G50 thermal gel to customer. But customer reply rapidly with doubt, “is thermal gel workable? We are using a thermal gel in our products, it performance well at the beginning, but we need to replace it once a year when it cures and fail to transmit heat.” This customer used a famous brand in Shenzhen. We knew about this situation much, the thermal gel will cure like thermal silicone grease in one year, and it drips off polluting other components. I assured customer that GLPOLY thermal gel will not cure in six years and it provdes a longer life than device’s. I suggested customer make an accelerated aging test to shorten design cycle. Customer accepted my suggestion and fixed test conditions: high temperture 150 degree centigrade, 720 hours, changes were within 5%. Comparing with rival’s changes of 10%, GLPOLY’s standard is much more rigorous. One month later, customer opened test chamber and found that GLPOLY XK-G50 thermal gel remained paste status. Performance test showed that changes of thermal conductivity and thermal impedance were less than 3%. “this is the best what I had test ever.” GLPOLY XK-G50 had been listed in customer’s supplier system. There is no quality complaint for nine consecutive years. GLPOLY XK-G50 thermal gel provides ultra low thermal impedance of 0.001℃in2/W, it wets out interfaces decreasing contact thermal resistance. XK-G50 had been verified by the third party for shocking test and aging test. Now GLPOLY is qualified partner to DJI, ZTE and GAC Auto. If there is only one supplier can meet your thermal management requirements, it would be GLPOLY.

Minimum Order: 10 long tons

As one of key areas of national economics, industry of new energy electric vehicle has attracted a great deal of investment, especially the core component-electric vehicle battery pack. The charge-discharge performance, volume and stability of battery pack affect performance of vehicle, and thermal management is a vital factor that affect performance of battery pack. Thermal interface materials is essential part of battery management system. GLPOLY foresaw the development trend of thermal interface materials that applied to battery pack, launching a thermally conductive epoxy adhesive for “cell to pack” battery pack. GLPOLY thermally conductive epoxy adhesive is designed for battery cell bond, eliminating battery modules, increasing energy density by 20% and decreasing components by 40%. CTP structure reduces manufacture complexity and cost, and certainly, it will improve heat transfer. GLPOLY thermally conductive adhesive was verified by third party, provding high reliability and security improving battery cell bond. GLPOLY thermally conductive adhesive has advantages as following: 1.Bonding strength 8MPa, maybe no comparable products in China; 2.Verified by third party, just few of manufacturers can provide verification report; 3.Automated production lines, keeps consistency of product. GLPOLY thermally conductive adhesive had been applied to Wangxiang A123, Xiaokang Motor and Farasis Energy for trial. GLPOLY was the first brand that recognized by three car manufacturers at the same time in China. GLPOLY has collaborated with LG, Freetech Auto Pilot, DJI, Han’s Laser etc., offering advanced technological thermal interface materials and thermal solutions. GLPOLY serves top-class clients.

Minimum Order: 10 long tons

It is easy to produce thermal gap pad, but to be honest, there are just a few of manufacturers who can produce quality thermal gap pad, GLPOLY is one of them. Why do I say it is easy to produce thermal gap pad? The main contents of thermal pad are similar, you can make primary product easily with some additives. Why is it hard to make quality product? because of different grade of raw materials, different batching accuracy. They are vital to thermal and physical properties. Counterparts will mislead customer paying attention to a specific parameter, ignoring other parameters. A pioneering thermal management solution supplier will never do this. GLPOLY provides customers with customized thermal materials as requested. An ltalian auto component supplier, the engineer gave me two instructions when he found us 1) thermal conductivity is not less than 2.0W/mK, 2) Compression is as big as possible. He did not give a specific vulue to compression that makes it difficult to satisfy. This thermal pad was going to be applied in electric vehicle battery pack, so we recommended a compression of 40% according to our experiences. After test, customer fed back the compression is not enough with 700N pressure, leaving gaps between waterplate and thermal pad, if we applied bigger pressure, we’ll destroy the waterplate. We adjust the compression ratio to 60%, this is all what domestic counterparts can do. But customer said we need to improve 10% more after assembling. The other two suppliers said it can not be done, this is the most we can do. But GLPOLY is still working on it, changing raw materials, adjusting additives. Finally, we achieved a conpression ratio of 72%. GLPOLY imported raw materials from Germany and Japan, and processed raw materials again with nanometer grinder, making particle size samller to improve heat transfer. Now GLPOLY is a quality partner to NIO, GAC etc. auto enterprises. GLPOLY help keep your devices performing at their best.

Minimum Order: 10 long tons

Product Description Wholesale GXV160 Lawn Mower 5.5HP 4 Stroke Petrol Greenworks Lawn Mower Product parameter Engine model GXV160 engine Engine displacement 163CC Operation mode hand push Cutting Deck Material Steel Engine Power 5.5HP Cutting Width 460mm (18 inch) Cutting height adjustment 25-70mm/1-2.7", 7 stage central Wheel Diameter Front 7" / Real 8" Bag Volume & Material 55L G.W. / N.W 34kg / 37kg Package size 79X55X48 cm 5.5HP 4 Stroke Garden Petrol Lawn Mower GXV160 Large Petrol Lawnmower 0

GLPOLY thermal silicone pad has drawn more and more attention from customers, even some top-class research institutes. Why do they choose GLPOLY? Deverse product standards, unstable quality, raw material inspection criteria have been applied, making customers confused. How can cutomers choose the ones they need? Following the authoritative standard. That’s what GLPOLY does, providing quality products and experiences. As technology development, more and more equipments need a thermal silicone pad for thermal transfer. In April 2018, Doctor. Wang from a research institute asked if we can provide a high performance thermal pad which is used for a national science program. We knew less about it and just provided samples as requested because this program is confidential. We got more information about this program till we had a technical meeting in July 2019. We discussed the reliability test and achieved agreement of test method finally. After the meeting, we prepared to proceeded reliability test, making thermal pad samples, producing tool and fixture, everything was on move as requested. The aging test were carried at 298°C for 516h. Test results surprised customer, because the change of parameters were within 5%, GLPOLY was the only one who met the requirements. GLPOLY thermal gap pad brings benefits for you, <>90% of radiation less than that of counterparts <>10-year reliability, <>Automated production system eliminates artificial errors. GLPOLY thermal gap pad are on trial in battery pack in four major electric vehicle ernterprises in China, NIO Automotive, GAC NE, Dongfeng Motor and Leapmotor. GLPOLY thermal interface materials provide you with exceptional performance products and design flexibility.

Minimum Order: 10 long tons

Power range 10W~500W 60mm ultra-thin design, beautiful and generous, can save customers a lot of freight Use Philips SMD 3030 LED, more than 130lm/w Two power supplies can be used-Meanwell drive and CE drive, input voltage is AC85-300V It is made of die-cast aluminum and 4 mm thick tempered glass. G-shaped buckle lock can protect the glass, easy to install and maintain. Equipped with a respirator, which can balance the air pressure inside and outside the lamp to prevent condensation of water mist inside the lamp. The reflectivity of the pure aluminum reflector is as high as 99%, which minimizes light loss. The mounting bracket has an adjustable angle of 270°, making it easy to install. Waterproof IP65 design + strong corrosion resistance It has ETL/DLC/CE/ROHS certifications The light-emitting angle is 120 degrees

Minimum Order: 5 dozens

80% of GLPOLY thermal management materials is of same quality level as top-class brands, the remaining 20% of products outperforms them I heard that a lot of domestic rivals said their products can substitutes for products of top-class brand, seems like it was easy to find an anternative in China. But that was not the case. Usually, customer can’t find an alternative product with excellent integrated performance from a dozen supplier, either thermal or physical properties fail to meet requirements. GLPOLY had catched up with top-class brand with integrated performance. A power supply technology company from Shanghai consulted with me about an alternative to Fujipoly GR-ae, requesting a thermal conductivity of 1.5W/mK, especially low hardness of Shore00 15 for low compressive force, decreasing stress on component thus decreasing component failures. I understood customer’s requirements, the greatest advantages of Fujipoly GR-ae are low hardness, low stress and high compression rate. There is no problem over thermal conductivity to most of suppliers but the hardness. So I recommended XK-P20 thermal gap pad with a thermal coductivity of 1.5W/mK to customerand and suggested he tested material in realistic settings. Test lasted for three weeks, data was perfect as we expected, thermal conductivity and hardness of GLPOLY thermal pad XK-P20, 1.5W/mK were equivalent to Fujipoly GR-ae, but thermal resistance is one fourth lower than that of Fujipoly GR-ae. That meant GLPOLY XK-P20 prvoided more exellent thermal properties. Customer decided to use XK-P20 thermal pad instead of Fujipoly. We had not received quality complaint for two years since XK-P20 thermal gap pad had been applied in volume production. GLPOLY has been providing thermal management materials for NIO electric vehicle, GAC NE and Chinese Academy of Sciences, especially, GLPOLY thermal management materials has been applied to military equipments in 2019 National Day Parade. GLPOLY thermal management materials are of excellent quality as top-class brands and it strives to exceed top class brands.

Minimum Order: 10 long tons