Offers to Sell

High frequency induction furnace has the remarkable ability to heat the entire workpiece or selectively target specific areas. This precise control translates into significantly lower power consumption, saving you valuable resources. POWER: this light is on when the control power switch is on. OPERATE: this one is flashing briefly and beeps have been heard constantly when the high frequency induction machine is working. OUTPUT OVERVOL.T: (NO). PHASE FAIL: this light is on shows that 3-phase has failed. If it is single phase, this light will be useless. SHORT CIRCUIT: When the light is on and the alarm is given, the IGBT module of the regulating part may be damaged, or the short circuit sensor may be damaged. Please consult our company for repair. OVER TEMP: When the temperature of these components is lower than 55 ℃, the alarm will be automatically lifted, and the overheat indicator light will go out. WATER FAIL: The light would be on and beeps would been heard if water flows too slow or pipes are blocked, the high frequency hardening machine would stop automatically. OVER CURRENT: the following six conditions may be happened when the light is on: ①signal interfered; ②the internal temperature being too high; ③breaking down of the machine; ④the soft induction ring been short circuited because the crucible or other metallic parts been touched the soft induction ring; ⑤two cycles of the ring been touched each other; ⑥input voltage is too much lower or overloaded.

Crafted with precision and innovation, this Super-Audio High Frequency Solid State Induction Heating Quenching Machine combines Siemens IGBT technology and German inverter expertise to deliver unmatched performance and reliability. 1. High frequency heating for hot upsetting of various high-strength bolts and nuts; 2. High frequency quenching of various gears, sprockets and shafts; 3. High frequency quenching of various axle shafts, leaf springs, shift forks, valves, rocker arms, ball studs and other auto parts. 4. High frequency quenching of various internal combustion engine parts and deceleration surface parts.   5. High frequency hardening of various pliers, scissors, axes, hammers and other hand tools. 6. High frequency hardening for all kinds of picks, drill bits, drill pipes, coal drill bits, air drill bits and other mines. 7. High frequency surface hardening for all kinds of bars, rods, sticks. 8. Diathermy forging heating of bars with a diameter of less than 800mm. 9. Hot upsetting and hot rolling of mechanical spare parts, hardware tools and straight shank twist drills. MAIN FEATURES 1. Adopt Siemens IGBT module as power driving part and unique inverter technology from Germany. 2. 100% load rate, can be working 24-hour per day even in maximum power working mode. 3. Automatic control type: heating time, heating power, holding time, holding power and cooling time can be adjusted. 4. Simple operation steps for any new worker can be learned in several minutes. 5. Simple installation, just connecting the 380V three-phase power supply, water inlet and outlet, and it can be completed in a few minutes. 6.  Solid State induction heater occupies a very small area, the operation is simple, and it can be learned in a few minutes. 7. Especially safe, the output voltage is lower than 36V, avoiding the danger of high voltage electric shock. 8. Heating efficiency is as high as 90% or more, saving energy. 9. Complete automatic protection functions such as over-current, over-voltage, over-temperature, water shortage, and lack of water, and is equipped with a fault self-diagnosis alarm system.

Cheapest HiDON 10 inch NFC Fingerprint 5G Android 12.0 OS Rugged Tablets,Rugged PAD,Embedded Industrial PC computer 1.CPU: Mediatek MT6891 Dimensity 1100 Octa-core 2.6GHz, 6nm Skill; 2.Operation System: Android 12.0 OS, 3.Display: 10.1 inch Capacitive 10-Point-touch IPS screen FHD 1920*1200 pixels; 4.Two Cameras: Front 8.0MP camera, Back 20.0MP camera; 5.Memory & Storage: 6GBram+128GBROM, 8GB+256GB or 12GB+1TB is optional; 6.5G Network: Support 2G GSM: B5/B8/B3/B2,3G WCDMA: B1/B2/B5/B8,3G CDMA: BC0/BC1, 4G TDD LTE:B34/B38/B39/B40/B41, FDD LTE:B1/B3/B5/B7/B8/B20/B26/B28A & B; 5G NR: N1/N3/N5/N7/N8/N20/N28/N38/N40/N41/N77/N78/N79; 7.Wireless network: WIFI:802.11 a/b/g/n/ac/ax wifi6 wireless and blutooth V5.1; 8.Battery: Built-in 3.8V/8500mAh Lithium Battery, 9.I/O Ports: 1*Type-C USB3.0 (OTG),1*Sim Slot,1*TF card slot,1*3.5mm Earphone jack,1*20-pin Pogo port; 10.Rugged Durability: Waterproof and dustproof rate:IP67; Ruggedness:1.0m dropproof; 11.Buttons: 1*power,1*volume +/-, 2*Self-defination Key F1 & F2; 12.Navigation & Position: Support GPS+Glonass+Beidou; 13.NFC: 13.56Mhz,support ISO14443A/B/15693/18092/18000-3,mifare. 14.Fing , erprint Scanner: Support unlock. 15.2D barcode scanner: Newland NLS-CM60 or others, is optional. 16. Handbelt: is optional. 17.Dimension: 252.7*171.9*15.6mm,about 830g.

Minimum Order: 1 bags

The blade gap can be adjusted with a handwheel, which is quick, accurate and convenient. Rectangular blade, all four cutting edges can be used, long service life. The shear angle is adjustable to reduce sheet distortion and deformation. The upper tool rest adopts an inward-inclined structure, which facilitates blanking and improves the accuracy of the workpiece. It has segmented cutting function and light alignment function. Motorized rear gauge, digital display. Rear supporting device (optional configuration available).

The main machine adopts the structure of series QC12Y hydraulic swing beam shear. Adopt DELEM CNC control system. The motor of backgauge can be equipped with importing AC servo motor. The drive element of backgauge adopts imported ball screw and linear guideway. User can choose other brand CNC system.

The machine adopts the four-roller structure with the upper roller as the main drive,Both upward and downward movement Through hydraulic motors powered.The lower roller makes vertial movements and imposes a force on the piston through the hydraulic oil in the hydraulic cylinder so as to clamp the plate tight.Side rollers are arranged on the two sides of the lides of the lower roller,and make inclining movement along the guide rail,and provide drive through the screw,the nut,the worm and the lead screw.The advantage of the machine is that the preliminary bending and rolling of the top ends of the plates can be conducted on the same machine.

Computer optimized design, 3-beam, 4-column structure, simple but with high performance price ratio. Cartridge valve integral unit equipped for hydraulic control system, reliable, durable and less hydraulic shock.with shorter connection pipeline and fewer releases points. Independent electrical control, reliable, audio-visual and convenient for maintenance. Centralized button control system,with adjustment，hand and semi-auto operation modes at operator's choice. Fixed stroke forming process or fixed pressure forming process selected through control panel, with pressure hold and time delay functions. The operating force, no-load traveling and, low-speed movement and travel range can be adjusted subject to technological requirements.

10pcs/Set Carbon Steel Scalpel Knife Blades Dental Surgical Blade. Disposable Sterile Scalpel Knife Blades can be used for surgery, dentistry, jewelry, mobile phone PCB DIY Repair Hand Tool. Sterile Surgical Scalpel Blades Stainless steel Graver for Phone Motherboard Glue/BGA CHIP Removing. Features: Sterile Scalpel Blades. 10PCS Surgical Blades Sterilized by Gamma Radiation. Fine workmanship, made of carbon steel. Sharp and stable, using a new type of automatic knife edge sharpening machine and integrated production. Independent packaging, using small pieces of independent packaging, safer and more hygienic. The scalpel blades are individually wrapped in foil pouches and are safe, effective and convenient. They come clean and ready to use, 100% brand new and sealed. Blade Model: (Carbon Steel ) 10# blade 10pcs/set fit No. 3 handles. 11# straight tip 10pcs/set fit No. 3 handles. 11# bevel tip 10pcs/set fit No. 3 handles. 12# blade 10pcs/set fit No. 3 handles. 15# blade 10pcs/set fit No. 3 handles. 15C blade 10pcs/set fit No. 3 handles. 18# blade 10pcs/set fit No. 4 handles. 20# blade 10pcs/set fit No. 4 handles. 21# blade 10pcs/set fit No. 4 handles. 22# blade 10pcs/set fit No. 4 handles. 23# blade 10pcs/set fit No. 4 handles. 24# blade 10pcs/set fit No. 4 handles. 25# blade 10pcs/set fit No. 4 handles. Handle Model:(Stainless Steel) No.3 Thin Handle. No.4 Thick Handle.

Minimum Order: 1 bags

Planetary winch gearboxes of the HFW series are composed of 16 finely spaced frame sizes. The compact design allows the gearbox to be integrated into the winch drum. The failsafe brake can be integrated inside the gearbox or mounted externally, with common lubrication for the gears. Electrically driven versions are available with both in-line and right-angle configurations. Torque ratings are organized by FEM class, in accordance with minimum approved class safety factors for gears. Key features Class approval program ATEX conformity on demand Torque ratings are organized by FEM class The failsafe brake can be integrated inside the gearbox or mounted externally, with common lubrication for the gears Specifications Torque range 3.000 ... 275.000 Nm

Minimum Order: 1 bags

Available in 30-5000ml, the bottle body and cap are made of high-purity PFA material, resistant to strong corrosion and high temperature: -200~+260℃. Can store standard chemicals for a long time without leaking. #reagentbottle #teflon #labware #samplingvials

HVT-50, HVT-56, HVT-80, 8bits and 16bits are all available.Independently produced, the price is more favorable.Can be used with all types of Anton Paar instruments without conflict. Caps, plugs and other digestion tube accessories can be sold separately. hashtag#Antonpaar hashtag#HVT50 hashtag#digestiontube hashtag#samplepreparation hashtag#CEM

It can be used with separation funnels, stirring plugs, condenser tubes and other vessels to form a distillation and condensation reaction device for the purification of substances. Available in 250ml-3000ml, the number of necks can be customized. Undertake various PFA welding, mold opening and other services. #teflon #flask #Roundbottomedflask #labware #semiconductor #newenergy

　　O-rings are fundamental components in engineering and manufacturing, widely used in sealing applications. They are found in everyday objects, from engines and hydraulic systems to household plumbing. But what exactly are O-rings made of? The composition of O-rings is a critical aspect of their functionality and reliability. 　　Material Composition 　　O-rings are typically manufactured from various elastomeric materials, with the most common being nitrile rubber (NBR), fluorocarbon rubber (FKM or NBR), silicone, and ethylene propylene diene monomer (EPDM) rubber. Each material offers distinct properties, making it suitable for specific applications. For instance, NBR exhibits excellent resistance to oils and fuels, while FKM withstands high temperatures and harsh chemicals. Silicone, on the other hand, boasts excellent flexibility across a wide temperature range. 　　Manufacturing Process 　　The production of O-rings involves precision and expertise. Initially, the raw materials are mixed and formulated to achieve the desired properties. This compound is then shaped through various methods such as compression molding, injection molding, or extrusion. The molding process ensures that the O-rings are formed with the required dimensions and properties, maintaining their elastic characteristics. 　　Importance of Material Selection 　　Selecting the appropriate material for O-ring production is crucial for ensuring optimal performance and longevity in specific applications. Factors such as temperature, pressure, chemical exposure, and mechanical stress play a vital role in determining the suitability of an O-ring material. For instance, in aerospace applications, where extreme temperatures and pressures are encountered, the use of high-grade FKM materials becomes imperative. 　　Environmental Impact 　　The environmental impact of O-ring materials is an increasingly vital consideration. While some materials are highly durable and resistant, they can pose challenges in terms of biodegradability and ecological impact. Silicone, for example, is known for its inert nature, making it less likely to react with environmental elements, while NBR, though robust, may have a greater environmental footprint due to its synthetic composition. 　　Future Innovations 　　As technology advances, so does the quest for improved O-ring materials. Researchers are exploring biodegradable elastomers and sustainable alternatives to traditional rubber compounds. Additionally, the use of nanotechnology in O- ring materials is being investigated to enhance their performance characteristics, such as improved heat resistance and chemical stability. 　　O-rings are fabricated from a range of elastomeric materials, each tailored to meet specific performance requirements. The quest for more sustainable and high-performance materials will undoubtedly lead to exciting developments in O- ring composition in the future.

Minimum Order: 500

25/55/75/100/110ml can be customized, and PFA or TFM materials are optional. Independently produced, the price is more favorable. It can be used with all types of CEM instruments without conflict. #digestiontube