Offers to Sell

Introduction What is AISI 5140 Steel? AISI 5140 steel also can be called JIS Scr440 and DIN 1.7035 steel.AISI 5140 steel round bar is one of the alloy steel as well as the most popular steel grades in the productions of the machine. The AISI 5140 steel price is on the medium level and it was easy to processing. After tempering and quenching, the toughness, plasticity and wearing resistance of it will get better. Steel normalizing can make the spheroidizing for the organization of steel get easier. And it will raise the machinability of the semi-finished product with the hardness less than 160HBS. Tempering it at the temperature of 550℃-570℃ which can make it get better mechanical property. And the hardenability of it is higher than S45C steel. You can check 5140 Steel chemical composition and mechanical properties as below. use 5140 This steel is quenched and tempered and used to manufacture mechanical parts that are subjected to medium load and medium speed work, such as steering knuckles of automobiles, rear axle shafts and gears, shafts, worms, spline shafts, top sleeves, etc. on machine tools; After quenching and tempering at medium temperature, it is used to manufacture parts that are subjected to high load, impact and medium speed work, such as gears, spindles, oil pump rotors, sliders, collars, etc. Low-impact and wear-resistant parts, such as worms, spindles, shafts, collars, etc., with a solid thickness of less than 25mm on the cross-section; after quenching and tempering and high-frequency surface quenching, they are used to manufacture high surface hardness and wear resistance And parts without great impact, such as gears, sleeves, shafts, main shafts, crankshafts, mandrels, pins, connecting rods, screws, nuts, intake valves, etc. In addition, this steel is suitable for the manufacture of various transmission parts for carbonitriding, such as gears and shafts with large diameters and good low temperature toughness Test How is ASTM 5140 steel tested? AISI 5140 Steel Chemical Composition Testing-Spectrometer We are sae 5140 Alloy Structural Steel for composition testing using spectrometer.The spectrometer one-time excitation of the sample to analyze its composition method is widely accepted by the public at this stage.Compared with traditional analytical methods, the advantages of spectrometers for the detection of modern steel components are fast, accurate and efficient. This method can directly inject solid samples without chemical digestion, which can reduce the human error caused by the digestion process and the constant volume process; to good quality steel. Dongguan Songshun Mould Steel Co.,LTD We are an Industrial and Trading Company with 3500,0000 hydraulic forging machine,who has about years experience in this field.We provide a great variety of steels, competitive price with good quality and keep the mass stock are over 20000 tons.Our main products are round and flat bars for alloy steel, tool steel, stainless steel, spring steel, bearing steel and etc. In those years we offer a wide range of high-quality steel for automobile manufacturing, engineering machinery, mold tooling, cutting tools manufacturing industry and also get high praise by at home and aboard clients. Songshun specialized in Special Steel for almost 20 years. We can supply mold steel, high speed steel, alloy steel, free cutting steel and etc.Welcome your contact 24 hours a day!!! E-mail:jacklu@songshunsteel.com Skype , /Whatsapp/Wechat:+86-18269260283 Songshun Tiktok:mikizhuo Songshun Facebook:Songshun Steel Songshun YouTube:MiKi Zhuo Songshun Company Website:https://steelpurchase.com/ http://www.songshunsteel.com/ songshunsteel , 41404340

Minimum Order: 2 barrels

Gas Welding Wire Supplier Specification： AWS ER80S - Ni1 G B ER55 - Ni1 Shieding Gas： 80%Ar + 20%CO2 Characteristics：  ( 1 ) The ER55 - Ni1 welding wire contains 1%Ni content, it has good plasticity and toughness ( 2 ) It’s used to weld steel of corresponding strength level, such as ships, bridges, pressure vessels, boilers, etc. Precautions： ( 1 ) Adequately clear the oil,rust,moisture,dust and other debris of the welded parts. ( 2 ) When heat input is too big, it can reduce impact value , so welder should pay attention to the choice of welding current. One chemical composition of the weld metal sample  (wt%) C Si Mn P S Ni 0.08 0.51 0.96 0.007 0.003 0.92 One mechanical properties of the weld metal sample Tensild Strength      MPa Yield Strength    MPa Elongation    % Impact value ℃ J 580 500 26 -45 125 The specifications of the product and welding condition (DC+)： Dia (mm) Welding Condition 1.0 1.2 1.4 1.6 Short Circuiting Transfer Current A 80 ~ 160 100 ~ 210 - - Voltage V 16 ~ 22 17 ~ 22 - - Spray Transfer Current A 180 ~ 280 200 ~ 300 210 ~ 320 220 ~ 330 Voltage V 24 ~ 30 24 ~ 30 24 ~ 32 24 ~ 32 We are Welding Wire Manufacturer and provide Quality High Strength Steel Welding, Non Copper Coated Wire, Submerged Arc & Stainless Steel Welding Wire. If you like, click here for more links.

Minimum Order: 10 long tons

Gas Shielded Welding Wire Supplier Specification： ISO G46 4 M21 Z3Si AWS ER80S - G GB ER55 - G Shieding Gas 80%Ar + 20%CO2 Characteristics： (1)This product is the 600MPa grade high strength steel wire, it has very good mechanical properties.  (2)With the mixed shielding gas, this wire widely used in steel, mining machinery, engineering machinery, automobile and other industries. Precautions： 1. Pay attention to the gas purity and mixture ratio.  2. Keep the gas flow rate between 15 ~ 25 L / Min.  3. The extension length keep between 15 to 20mm   4. Clear the oil, rust, moisture, dust and other debris of the welded parts.  5. Keep the welding hood clean and unobstructed. Hebei XINYU Welding Co., Ltd, which mainly produces high strength steel welding wire, Non-copper-coated solid wire, submerged arc & stainless steel welding wire . Our products are widely applied to the welding of low-alloy high tensile large & key steel structures in coal machinery, construction machinery, petrochemical machinery, pressure vessels or tanks, oil & gas pipelines, military industry, shipbuilding, bridge and high-rise buildings etc. At the same time,we are the only interprise in the domestic which produces welding wire as well as welding wire equipment. Welcome you to our factory any time.

Minimum Order: 10 long tons

ER50-G Welding Wire Specification AWS ER70S-G J I S YGW15 G B ER50-G Shielding Gas 80%Ar+20%CO2 Feature & Use： ( 1 ) Operating condition is wide, from low to high current. It is a kind of solid wire. ( 2 ) Containing special alloy, its arc is stable even in high current. ( 3 ) Adapt to 490 MPa steel , like ships, steel structures, and machinery etc. Notice of ER50-G Welding Wire： 1. Please use specialized welding gas, eg: purity of CO2≥99.5%，H2O≤0.005%， Ar≥99.99%. Gas flow: 20~25L/min. 2. Wind affects arc and welding pool, please take steps to block the wind. 3. There is smoke when welding, pay attention to ventilation. 4. Distance between Tip and base steel is about 15mm when current is below 250A; and 20~25mm when current is above 250A. 5. Welding materials should be stored in dry places. 6. Please check the welder ,wire feeder, gas regulator and heater before operation. 7. Please keep the percentage of mixed gas stable and keep gas pressure stay the same. 8. As to thin steel plate, downward welding in the inclined position or forward welding is recommended,(pictures are followed below). 9. Please move plastic spool and basket spool in a correct way. One chemical composition of deposited metal (wt%)：（80%Ar+20%CO2） C Si Mn P S 0.08 0.42 1.04 0.016 0.025 Size & Current (DC+)： Diameter (mm) 0.8 0.9 1.0 1.2 1.4 1.6 Current  (Amp) PA 50 ~  180 50 ~  200 50 ~  220 80 ~  350 100 ~  470 200 ~  550 EGW 50 ~  120 50 ~  140 50 ~  140 50 ~  160 100 ~  180 — PE 50 ~  100 50 ~  120 50 ~  120 50 ~  140 — — We are Welding Wire Manufacturer and provide Quality High Strength Steel Welding, Non Copper Coated Wire, Submerged Arc & Stainless Steel Welding Wire.If you are interested, please click here to contact us immediately.

Minimum Order: 10 long tons

Gas Shielded Welding Wire Specification： ISO G42 4 M21 3Si1 AWS ER70S-6 GB ER50-6 Shieding Gas： CO2 or 80%Ar+20%CO2 XINYU Gas Welding Wire Description Characteristics： (1) This product is the general MAG / CO2 welding wire and suitable for all- position welding (2) The wire have stable arc at low currents , less sparks and splashing, and adapt to larger current range Precautions： 1. Pay attention to the gas purity and mixture ratio.  2. Keep the gas flow rate between 15 ~ 25 L / Min.  3. The extension length keep between 15 to 20mm   4. Clear the oil, rust, moisture, dust and other debris of the welded parts.  5. Keep the welding hood clean and unobstructed. One chemical composition of the weld metal sample  (wt%) （Shielding Gas:CO2） C Si Mn P S 0.08 0.68 1.32 0.011 0.008 Hebei XINYU Welding Co., Ltd, mainly produces high-strength steel welding wire, Non-copper-coated solid wire, submerged arc & stainless steel welding wire. Our Welding wires and welding wire equipment are exported to the USA, Italy, Brazil, Russia and India, etc. All products have passed ISO 9001-2015 quality system certification and CE certification.If you are interested, please click here to contact us immediately.

Minimum Order: 10 long tons

Specification AWS ER120S-G ISO G89 4 M21 ZMn3Ni2CrMo G B ER83-G Shielding Gas 80%Ar + 20%CO2 XINYU High strength steel welding wire Description Feature & Use： ( 1 ) For 890MPa high tensile steel, containing Ni，Cr，Mo etc，excellent mechanical properties. ( 2 ) Adapt to low-alloyed steel structures according to 890 MPa. Notice： 1. Please use specialized welding gas, eg: purity of CO2≥99.5%，H2O≤0.005%， Ar≥99.99%.

Minimum Order: 10 long tons

Welding wire for construction machinery Specification ISO G69 4 M21 ZMn3NiMo AWS ER110S-G GB ER76-G Shieding Gas 80%Ar + 20%CO2 Characteristics： (1) This product is the 800MPa grade high strength steel wire, it has very good mechanical properties.  (2) With the mixed shielding gas,this wire can be used to welding the important corresponding level structures. Precautions： 1. Pay attention to the gas purity and mixture ratio.  2. Keep the gas flow rate between 15 ~ 25 L / Min.  3. The extension length keep between 15 to 20mm   4. Clear the oil, rust, moisture, dust and other debris of the welded parts.  5. Keep the welding hood clean and unobstructed. One chemical composition of the weld metal sample (wt%)  （Shielding Gas:80%Ar+20%CO2） C Si Mn P S Else 0.07 0.50 1.52 0.008 0.005 -- One mechanical properties of the weld metal sample  （Shielding Gas:80%Ar+20%CO2） Tensild Strength      MPa Yield Strength      MPa Elongation      % Impact Energy Value ℃ J 835 760 23 -20 95 The applicable current range and specifications of the product (DC+): Dia (mm) 1.2 1.4 1.6 Current Range    (Amp) Flat /Flat fillet welding 200 ~ 350 250 ~ 450 300 ~ 550 Horizontal welding 200 ~ 320 250 ~ 400 300 ~ 450 Hebei XINYU Welding Co., Ltd, which mainly produces high strength steel welding wire, Non-copper-coated solid wire, submerged arc & stainless steel welding wire . Click here to visit our factory.

Minimum Order: 10 long tons

=Specification ISO G62 4 M21 ZMn3Cr AWS ER100S-G GB ER69-G Shieding Gas 80%Ar+ 20%CO2 Product Description Characteristics： (1) This product is the 700MPa grade high strength steel wire, it has very good mechanical properties.  (2) With the mixed shielding gas,XINYU Gas Shielded Welding Wire can be used to welding the important low alloy structures, and widely used in the welding of scraper chain and hydraulic supports in mining machinery Precautions： 1. Pay attention to the gas purity and mixture ratio.  2. Keep the gas flow rate between 15 ~ 25 L / Min.  3. The extension length keep between 15 to 20mm   4. Clear the oil, rust, moisture, dust and other debris of the welded parts.  5. Keep the welding hood clean and unobstructed. One chemical composition of the weld metal sample (wt%)  （Shielding Gas:80%Ar+20%CO2） C Si Mn P S Else 0.08 0.60 1.45 0.010 0.005 -- One mechanical properties of the weld metal sample  （Shielding Gas:80%Ar+20%CO2） Tensild Strength      MPa Yield Strength      MPa Elongation      % Impact Energy Value ℃ J 750 655 23 -20 94 The applicable current range and specifications of the product (DC+): Dia (mm) 0.8 0.9 1.0 1.2 1.4 1.6 Current Range    (Amp) Flat welding 50 ~ 180 50 ~ 200 50 ~ 220 80 ~ 350 100 ~ 470 200 ~ 500 Vertical up welding 50 ~ 100 50 ~ 140 50 ~ 140 50 ~ 140 100 ~ 180 — Overhead welding 50 ~ 100 50 ~ 120 50 ~ 120 50 ~ 160 — — Vertical down welding 50 ~ 100 50 ~ 200 — — — — We mainly produces Welding Wire, Stainless Steel Wire, Non Copper Coated Wire. Inculding er70s 6 welding wire, er80s g welding wire.Click here to browse the website.

Minimum Order: 10 long tons

aisi 4140 Steel Structural High toughness aisi 4140 Steel Structural Bars What is AISI 4140 Steel? AISI 4140 alloy steel round bar sheet plate belongs to medium hardenability steel.AISI 4140 steel round bar has high fatigue strength and low notch sensitivity. Low-temperature impact toughness is also very high, no obvious temper brittleness. It is mainly used after quenching and tempering state. It is used to manufacture high-strength parts under impact loads and the fittings with large cross-sections and other stressed members. Such as the horizontal eccentric shaft of the horizontal forging machine, the crankshaft of the forging press, and etc. Its equivalent grade is JIS SCM440 and DIN 1.7225. The properties and composition of 4140 steel round bar sheet plate as below. What is the application of 4140 steel? AISI 4140 steel round bar is an alloy structural steel with good strength and good comprehensive mechanical properties after heat treatment. It has good manufacturability. The maximum operating temperature is 427°C. It is used to manufacture forgings that require higher strength and larger quenched and tempered section than 35CrMo steel, and can also be used to manufacture turbine fasteners, tool bodies, dies, brake shoes, etc. keyword   aisi 4140 Steel Structural Standard AISI/ASTM/DIN/NF/JIS/GB/BS Steel Grade AISI 4140/ASTM 4140/DIN 1.7225 /NF 40CD4 /JIS SCM440 /GB 42CrMo /BS 708M40 Chemical Compositions(%) C: 0.38-0.45   Si: 0.17-0.37  Mn: 0.50 , -0.80  P≤0.035  S ≤0.035   Cr: 0.90-1.20  Mo: 0.15-0.25 Mechanical properties Tensile strength σb (MPa): ≥1080(110) Yield strength σs (MPa): ≥930(95) Elongation δ5 (%): ≥12 Area shrinkage ψ (%): ≥45 Impact energy Akv (J): ≥63 Impact toughness value αkv (J/cm2): ≥78(8) Hardness: ≤217HB Sample size: sample blank size is 25mm Surface treatment Black/Peeling/Polishing/Machined Technique Cold/Hot rolled, Cold-Drawn or Hot Forged Heat Treatment Annealed; Quenched; Tempered Delivery Condition Hot Rolled or Forged/Peeled or Black Surface/Annealed or QT Heat treatment standard Quenching at 850℃, oil cooling; tempering at 560℃, water cooling, oil cooling Metallographic structure Tempered sorbite Test SGS/UT100%/Elements Testing Certificate SGS/ISO/Mill Certificate Delivery status Delivered in heat-treated (normalized, annealed or high temperature tempered) or unheated state Skype/Whatsapp/Wechat +86-18269260283 Company website https://steelpurchase.com/ http://www.songs , hunsteel.com/ songshunsteel41404340

Minimum Order: 1 bags

Product Features This pipe fitting can apply to water,air,gas,oil and fuel. Hex nipple for connecting two threaded pipes or fittings. Material: Brass for corrosion resistance, ductility at high temperatures, and low magnetic permeability. This hex nipple fitting is a short length of pipe with threaded ends for connecting threaded pipes, and it has a hexagonal section in the middle for an increased bearing surface when adjusting the fitting with a wrench.

Material SCM440 Steel Product Information 1.Describe: 4140 steel is a kind of alloy structural steel. It belongs to the steel with the American grade equivalent to the 42CrMo grade in my country. This kind of steel belongs to the medium hardenability steel with high yield, good comprehensive mechanical properties, good strength, good toughness and hardenability. High advantages, its carbon content is 0.33%-0.48%, its tensile strength is 795 MPa, and its hardness is 241HB. After heat treatment at 4140, it has good strength and good comprehensive mechanical properties, and it has good manufacturability. Fasteners, salvage tools, etc. 2.Corresponding steel number: China GB steel number 42CrMo, Germany DIN steel number 42CrMo4, Germany DIN material number 1.7225, French NF standard 40CD4/42CD4, Japanese JIS standard SCM440, British BS standard 708M40/708A42/709M40, American AISI/ASTM 4140, American SAE 4140, American UNS Standard G41400 (4140 alloy structural steel, executive standard: ASTM A29/A29M-04) 3.Application: It is used to manufacture forgings that require higher strength and larger quenched and tempered section than 35CrMo steel, such as large gears for locomotive traction, supercharger transmission gears, rear axles, connecting rods and spring clips that are heavily loaded, and can also be used for Drill pipe joints and fishing tools for oil wells below 2000m, and can be used for molds of bending machines, etc. 4.Feature: This steel has good strength, good toughness, high hardenability, good workability, small processing deformation, quite good fatigue resistance, small deformation during quenching, and high creep strength and durable strength at high temperature. ​ We provide high-quality steel,ex-factory price, support customization, strong company and factory strength; welcome your inquiry and order;please contact us for quotes. songshunsteel41404340

Minimum Order: 2 barrels

Hydraulic Waste Material Balers, ranges from 40 tons to 120 tons pressure force, has a processing power of up to 10 tons per hour. It is perfect for recycling shed handling large daily amount of soft waste such as cardboard, paper, plastic film, natural fiber, packing materials, etc. It combines advanced computer controlled operations with reliable hydraulics and seamless heavy duty frame construction. Application: Applicable for baling & belting of loose materials like scrap paper (cardboard, newspaper), plastic scraps(PET bottle, plastic film or crates) & straw, hay, etc. Ideally suited to recycling companies, manufacturing plants, printers & convertors , warehouse and distribution , manufactures of packaging ......

1. Steel Grade AISI 4140/DIN 1.7225/JIS SCM440/GB 42CrMo Size & Dimension Dia:20-120mm L:2000-5800mm Surface treatment Black/Peeling/Polishing/Machined Technique Cold/Hot rolled, Cold-Drawn or Hot Forged Heat Treatment Annealed; Quenched; Tempered Delivery Condition Hot Rolled or Forged/Peeled or Black Surface/Annealed or QT Test SGS/UT100%/Elements Testing Certificate ISO/Mill Certificate AVAILABLE Steel Type Round bar/Plate 2. AISI 4140 alloy steel round bar sheet plate has high fatigue strength and low notch sensitivity. Low-temperature impact toughness is also very high, no obvious temper brittleness. It is mainly used after quenching and tempering state. It is used to manufacture high-strength parts under impact loads and the fittings with large cross-sections and other stressed members. Such as the horizontal eccentric shaft of the horizontal forging machine, the crankshaft of the forging press, and etc. And the equivalent grade for it is DIN 1.7225 and JIS SCM440. 4140 Steel properties and chemical composition as below. 3. AVAILABLE SIZE: Round bar: Diameter(mm) Max 800mm; Length(mm) Max 12000mm. Plate: Thickness(mm) Max 800mm; Width(mm) Max 2300mm; Length(mm) Max 12000mm. Condition: Cold rolled(drawn)≤50mm, Hot rolled≤12-250mm, Hot forged≥50mm.   AISI 4140/DIN 1.7225 Introduction: AISI 4140 alloy steel is chromium, molybdenum, manganese containing low alloy steel. It has high fatigue strength, abrasion and impact resistance, toughness, and torsional strength.   Fabrication and Heat Treatment: 1. Forging Preheat the steel carefully, then raise the temperature to 1150-1200°C for forging. Do not forge below 850°C. 2. Annealing Heat the AISI 4140 slowly to 800-850°C and allow enough time for the steel to be thoroughly heated. Cool slowly in the furnace to 480°C followed by air cooling. 3. Stress Relieving When parts are heavily machined, ground or otherwise subject to cold work, stress relieving will be beneficial prior to hardening. 4. Hardening AISI 4140 steel is usually supplied ready heat treated to 18-22HRC. If further heat treatment is required annealed AISI 4140 should be heated slowly to 840- 875°C and after adequate soaking at this temperature quench in oil. Temper as soon as the tools reach room temperature. 5. Tempering Heat the AISI 4140 carefully to a suitable temperature selected by reference to a tempering chart or table (usually between 550-700°C, soak at the temperature for 2 hours per 25mm of ruling section, then allow to cool in air. Tempering between 250-375°C is not advised as tempering within this range will seriously reduce the impact value. 6. Surface Treatment Plate: Origin Black, Orign cold rolled bright, Machined, Grinded Bar: Origin Black, Orign cold rolled(drawn) bright, Turned, Peeled, Grinded ABOUT US: We specialize in 4140 and 4340 steels, which are versatile and have many advantages for a variety of industrial applications. Knowing the differences between them will help you choose the one that best suits your needs.   ​Our advantages: Focus on the steel industry for more than ten years, strong factories, professional services, ensure quality, customize according to customer requirements, factory prices, fast transportation,Good after-sales service, pleasant cooperation, high repurchase rate and so on. We offer a wide range of information and high quality steel products on 4140 and 4340 steel, for more information on our 4140 and 4340 steel products, please contact us today. To discuss pricing details, please request a quote. CONTACT US: MiKi Zhuo E-mail:jacklu@songshunsteel.com Skype/W , hatsapp/Wechat:+86-18269260283 ADD:No.4 Dongda Street, Shatou, Changan Town, Dongguan City, Guangdong Province, P.R.C China For more 4140 steel product information, please click this link: https://steelpurchase.com/aisi-4140-steel , -round-bar-sheet-plate-jis-scm440-din- 1-7225/< , br>songshunsteel41404340

Minimum Order: 2 barrels

4140 steel, this steel has good workability, small processing deformation, good fatigue resistance, is a medium hardenability steel, 4140 has good strength and good comprehensive mechanical properties after heat treatment, good workability, yield High. The maximum use temperature is 427 degrees Celsius. 4140 strength, high hardenability, good toughness, small deformation during quenching, high creep strength and lasting strength at high temperature. It is used to manufacture forgings that require higher strength and larger quenched and tempered section than 35CrMo steel, such as large gears for locomotive traction, supercharger transmission gears, rear axles, connecting rods and spring clips that are heavily loaded, and can also be used for Drill pipe joints and fishing tools for oil wells below 2000m, and can be used for molds of bending machines. ASTM 4140 Surface Treatment and Heat Treatment 1.Surface Treatment Plate:Origin Black,Orign cold rolled bright, Machined,Grinded Bar:Origin Black,Orign cold rolled(drawn) bright,Turned,Peeled,Grinded Heat treatment specification Heat treatment standard: quenching at 850℃, oil cooling; tempering at 560℃, water cooling, oil cooling; 4140 Steel Applications It is used to manufacture forgings that require higher strength and larger quenched and tempered sections than 35CrMo steel, such as large gears for locomotive traction, supercharger transmission gears, rear axles, connecting rods and spring clips that are heavily loaded, and can also be used for Drill pipe joints and fishing tools for oil wells below 2000m, and can be used for molds of bending machines, etc.                     How is SAE 4140 steel tested? Our AISI 4140 steel round bar and steel plate composition detection is carried out by a spectrometer, which is fast, accurate and efficient in detection; hardness is tested by a hardness tester, The hardness tester is based on the Leeb hardness measurement principle, which can easily and quickly measure a variety of metal materials. While displaying the hardness measurement value immediately, it can be freely converted between different hardness scales, and the tolerance limit can be set in advance, and it will automatically alarm when it exceeds the range. 1. Measuring range: (170-960)HLD,(17-68.5)HRC,(19-651)HB,(80-976)HV,(3 , 0-100)HS, (59-85)HRA(13-100 )HRB 2. Measurement direction: support 360° (vertical down, oblique down, horizontal, oblique up, vertical up) 3. Hardness scale: Richter (HL), Brinell (HB), Rockwell B (HRB), Rockwell C (HRC), Rockwell A (HRA), Vickers (HV), Shore (HS) 4. Display: quarter dot matrix LCD 5. Data storage: maximum 500 groups (impact times 32 to 1) 6. Working voltage: 3V (2 AA size alkaline batteries connected in series) 7. Continuous working time: about 100 hours (when the backlight is not turned on) FAQ Q:Are you a factory or a trading company? A: The fact is that we are a company. We have own factory and several warehouses. Under the trend of globalization of the world, we established a professional foreign trade department to change the world. Q: What is your delivery date? A: The delivery date is about 10-30 days after receipt of payment. Q: Can I get some samples? A: We are honored to offer you samples. Q: What port do you usually ship from? A: We have 3 common ports,Tianjin, Shanghai and Shen. Q: What is the payment terms? A: T/T is our priority, L/C is also OK for us. Songshun specialized in Special Steel for almost 20 years. We can supply mold steel, high speed steel, alloy steel, free cutting steel and etc.Welcome your contact 24 hours a day!!! E-mail:jacklu@songshunsteel.com Skype , /Whatsapp/Wechat:+86-18269260283 Songshun Tiktok:mikizhuo Songshun Facebook:Songshun Steel Songshun YouTube:MiKi Zhuo Songshun Company Website:https://steelpurchase.com/ http://www.songshunsteel.com/ songshunsteel , 41404340

Minimum Order: 1 bags