Tools & Hardware

Xian County Longge Automobile R epair Tools Co.,ltd has been in operation for 24 years, specializing in producing automotive repair tools and hardware tools. Our main products include: engine crane, high transmission jack, air hammers, airbag jack, jack stand, car ramps( plastic/steel), floor jacks, plasterboard lift , various puller tools, and manual tools. Our principle: quality first, service first. We offer one-stop service, making it convenient for customers to choose and freely combine with container loading. Welcome global distributors to negotiate and consult. Cooperation hotline: +86 15031758228 (whatsapp/wechat) Contact: JERRY Email: jerry@longge-tools.com jerry@czkes.com Website : www.auto-repairtools.com Facebook : https://www.facebook.com/share/1ELQW1hrFm/ Youtube: https://youtube.com/@zhaojerry-longge?si=waVmMGMNK , ARVO1ZV

Minimum Order: 1 bags

CIS Industrial marine end suction centrifugal pump CIS pump refers to the CIS series marine horizontal centrifugal pump, which is a single-stage single suction centrifugal pump mainly designed for marine environments and can also be widely used in industrial and agricultural fields. ‌ Core Features Applicable medium: It can transport seawater, fresh water, and other liquids with physical and chemical properties similar to water. Main uses: often used as fire pumps, cooling pumps, ballast pumps, general pumps, and sanitary pumps on ships; In non marine scenarios, it can be used for urban water supply and drainage, farmland irrigation, etc. Rotation direction: From the drive end, the pump rotates clockwise. Structural features: Adopting a horizontal structure, some models have a rear opening door /back pull door design, which does not require disassembly of pipelines and motors during maintenance, making maintenance convenient. ‌ CIR series: Same performance parameters and installation dimensions as CIS pumps, but specifically designed for delivering hot water, with hot water temperatures typically not exceeding 120 degrees Celsius. ‌ This series of pumps is usually equipped with a 380V/50Hz three-phase power supply, with common speeds of 1450r/min or 2900r/min. The specific selection depends on the flow rate and head parameters. ‌ Pump body/housing: cast iron Impeller: bronze Stainless steel pump shaft.

Minimum Order: 1 bags

FP series polypropylene corrosion-resistant pump is a fully injection-molded plastic corrosion-resistant pump, with its flow components made of reinforced polypropylene (PP) material. The medium does not come into contact with metal, offering excellent corrosion resistance and suitable for general non-metallic corrosive clear liquid media within a temperature range of 0 to 85 degree celsius/. The main advantages of the FP series polypropylene corrosion-resistant pumps compared to other anti-corrosion pumps are: 1. The hydraulic model is advanced, efficient, and highly energy-saving. 2. Lightweight and compact. 3. The price is affordable, and compared to other corrosion-resistant pumps, it offers a better cost-performance ratio when used in general corrosive media. 4. The import and export flanges feature a steel skeleton wrapped with plastic, offering the advantages of excellent installation strength and superior corrosion resistance compared to other plastic pumps. When selecting this pump, users should provide our company with detailed operating conditions, such as the chemical properties, solid content, viscosity, temperature, explosion-proof requirements, and usage position of the conveying medium, in order to accurately select. （2） FP type pump has a bracket structure (shaft coupling) and is characterized by easy maintenance. FPD type pump is a direct coupled structure (close coupling), characterized by being lightweight, energy-saving, and economical.

Minimum Order: 1 bags

FP Reinforced polypropylene centrifugal pump FP centrifugal pump adopts reinforced polypropylene (RPP) injection molding. It has the advantages of high mechanical strength and corrosion resistance, Light weight, small size, long life etc. FP RPP centrifugal pump is widely used in chemical, food, pharmaceutical, electroplating, papermaking, environmental protection, water treatment and other departments for conveying acid, alkali, salt and other corrosive liquids Pump material (pump body, pump cover and impeller): RPP Mechanical seal: WB2 externally mounted mechanical seal Operating temperature is -12℃ to 100℃.It is a good matching pump for engineering plastic water jet vacuum pump Closed coupling type

Minimum Order: 1 bags

IS-type single-stage single-suction centrifugal pump The IS pump is a single-stage, single-suction horizontal centrifugal pump compliant with ISO standards, primarily used for conveying clean water or similar liquids. Basic Definition: The IS pump, full name IS type single-stage single-suction centrifugal pump, is an energy-saving pump manufactured according to the national joint design standard, replacing the outdated BA type and B type pumps. Primary Uses: Widely used in industrial and urban water supply and drainage, agricultural irrigation and drainage, as well as in fire protection pressurization, garden sprinkler irrigation, and other scenarios. Structural Features: Designed with a "rear-opening" mechanism, allowing easy rotor removal by disassembling the coupling without the need to dismantle pipelines or motors during maintenance, ensuring convenient servicing. Usage Limitations: Typically suitable for pumping clean water with a temperature not exceeding 80°C. For high-temperature or corrosive liquids, the IR-type hot water pump or derivative models such as chemical pumps should be selected.

Minimum Order: 1 bags

LC vertical long-shaft pump is a newly developed product with both homeland and overseas advanced experience in design and manufacture. It is used to deliver clear water, sewage with certain solid particles (such as iron scrap, sand, coal powder etc.) and industry waste water and seawater with corrosive. The temperature of liquid can not be above 80"C. It is widely used in original water works, waste water factory, metallurgy and steel industry (especially suitable for delivering oxygenation iron sheet water in swirl pool), power station, mine, civil project and farmland etc. model meaning 300L C200-50*2 * 300 -Outlet diameter of pump is 300mm * LC -Vertical long-shaft pump * 200 - Design capacity is 200m3/h * 50 - The head is 50m at design point * 2 - Impeller stage numbe Performance Range Capacity: 50-8400m3/h Head: 12.5-250m Construction Feature The type LC vertical long-shaft pump is installed with single foundation, its inlet is vertical downward and outlet is horizontal. The pump and the motor are directly connected. The rotation of pump rotor is counter clockwise looking from the motor to the pump; the main features are as following: 1. It is fine designed with hydraulic design software. It makes impeller and other wearing parts have a long life because of anti-abrasive impeller and Diffuser. The pump is not only reliable, safe, steady but also saving energy. 2. There is filter in pump inlet with proper hole, this can not only prevent impurity entering pump to damage pump but also decrease inlet loss and increase pump efficiency. 3. Impeller adopts balance hole to balance axial force. There is replaceable seal ring in front and back cover board of impeller to protect impeller and pump. 4. Pump middle shaft, water column and guard pipe are multi-burl, middle shaft uses technology of sleeve coupling. Water pipe can be more or less for different inundated depth according to user's requirement. Impeller and Diffuser are multi-stage for different head. 5. Water pipe is connected by flange with guide bearing in its middle. Pump guide bearing adopts ethane, it can also adopt rubber (when the temperature of liquid is over 55degree celsius).Shaft is protected by guard column, the guide bearing should be supplied with exterior cooling lubricating water, while delivering sewage. 6. The remaining axial force of pump and the weight of rotor parts are borne by thrust bearing in motor seat or motor with thrust bearing. The thrust bearing is lubricated by dilute oil and cooled with exterior water. The thrust bearing can have element for monitoring temperature. 7. Pump shaft seal adopts packing seal, there is replaceable shaft sleeve in shaft seal and guide bearing to protect shaft and it is convenient to adjust axial location of impeller by nut in bearing parts upper end or pump coupling. 8. Pump can be equipped with controller which can automatically start and stop pump according to liquid level, give an alarm for over loading and control many pumps in long-distance. There is automatic exhaust system for pump with diameter over 500mm.

Minimum Order: 1 bags

Sea water desalination pump The core flow components (impeller, pump casing, shaft, etc.) of seawater desalination pumps are preferably made of duplex stainless steel or super duplex stainless steel to resist corrosion and stress cracking in high chloride environments. Core Recommended Material • Super Duplex Stainless Steel (e.g., 2507/S32750): Currently the mainstream choice for high-pressure pumps in large-scale reverse osmosis seawater desalination systems. With high pitting resistance equivalent number (PREN), it effectively resists corrosion from chloride ions and stress corrosion cracking in seawater, offering superior mechanical strength compared to ordinary stainless steel, making it suitable for high-pressure applications. • Duplex stainless steel (e.g., 2205/S31803): Suitable for booster pumps and transfer pumps in medium-low pressure or pretreatment stages. It offers better cost performance than super duplex steel and significantly outperforms 316L in corrosion resistance, making it a commonly used balanced solution in engineering applications. • Super austenitic stainless steel (e.g., 904L, 6% Mo steel): Used as an alternative in specific highly corrosive or high-temperature applications, offering excellent corrosion resistance but at a high cost, typically employed for critical seals or special components 316/316L stainless steel: Although containing molybdenum element, it has insufficient resistance to pitting and crevice corrosion in long-term seawater environment, and is prone to local corrosion. It is only recommended for short-term, low flow rate or non critical auxiliary pipelines and is not recommended as the main material for core overcurrent components. bronze alloy (such as nickel aluminum bronze): a traditional marine material, but it is susceptible to cavitation corrosion and electrochemical corrosion under continuous operation conditions of seawater desalination, and environmental restrictions have increased. Modern large-scale desalination plants have gradually been phased out. Ordinary carbon steel/cast iron: no anti-corrosion ability, strictly prohibited from direct contact with seawater medium Distinguishing working conditions: The high-pressure pump (RO system core) must use high-grade materials such as 2507; The water intake pump/discharge pump can use 2205. Process control: Duplex stainless steel has extremely high requirements for welding and heat treatment processes, and it is necessary to ensure the balance of ferrite/austenite ratio, otherwise brittle phases may precipitate and cause failure. Non metallic materials: Some seals, bearings, or liners may use special engineering plastics such as carbon fiber reinforced PEEK to assist in corrosion resistance and friction reduction. It is recommended to prioritize API 610 standards material confirmation based on specific pressure levels, seawater temperatures, and project budgets

Minimum Order: 1 bags

https://www.kntreinforced.com/product-list-grp , -scrubber.html Welcome to Hebei KNT, your reliable supplier of GRP Scrubbers. Our Glass Reinforced Plastic (GRP) Scrubbers are designed to effectively remove pollutants and harmful gases from industrial exhaust systems. Made from durable, corrosion-resistant GRP material, our scrubbers offer long-lasting and cost-effective air pollution control solutions. Why Choose GRP Scrubbers? Corrosion-Resistant: Ideal for handling corrosive gases and harsh environments. Durable and Lightweight: GRP offers strong yet lightweight construction for easy installation and maintenance. Efficient Air & Gas Treatment: Effectively remove harmful gases like sulfur compounds, VOCs, and ammonia. Cost-Effective: Lower maintenance and long service life compared to metal scrubbers. Types of GRP Scrubbers Vertical GRP Scrubbers: Compact, effective for treating gas or air in confined spaces. Horizontal GRP Scrubbers: Suitable for larger gas volumes, providing high efficiency. Packed Bed Scrubbers: Best for removing acidic or basic gases. Venturi Scrubbers: Effective for scrubbing fine particles and gases. Chemical Scrubbers: Designed for handling hazardous chemical pollutants.

Welcome to Hebei KNT, your trusted provider of high-quality Insulated GRP Tanks. Our tanks are designed to keep liquids at the right temperature, offering reliable, corrosion-resistant, and energy-efficient storage solutions for various industries. Why Choose Insulated GRP Tanks? Temperature Control: Insulation keeps liquids at the desired temperature, whether for heating or cooling. Corrosion Resistant: Made from durable fiberglass, these tanks resist chemicals, acids, and environmental damage. Energy Efficient: Insulated tanks reduce energy consumption, providing an eco- friendly and cost-effective solution. Long-Lasting: GRP tanks are strong, lightweight, and built to withstand harsh conditions. Types of Insulated GRP Tanks Water Storage Tanks: Keep water at a stable temperature for heating systems and industrial use. Chemical Storage Tanks: Ideal for storing temperature-sensitive chemicals. Food-Grade Tanks: Maintain the right temperature for storing liquids like oils and juices. Wastewater Tanks: Used in treatment processes where temperature control is crucial. Fuel Storage Tanks: Ensure safe storage of fuel and other liquids at a stable temperature.

Busbar Systems for Plant Reliable Industrial Power Distribution Solutions for Factories and Workshops Our Busbar Systems for Plant provide safe, efficient, and high-capacity power distribution solutions for industrial facilities. Designed for demanding environments, our systems are suitable for factories, workshops, energy plants, and automated production lines. Available in enclosed, insulated, and modular designs, these busbars ensure stable electricity supply, low maintenance, and long service life.   Explore Our Busbar Products Below is an overview of our core Busbar systems for plant solutions designed for industrial power distribution, material handling facilities, workshops, and manufacturing plants. Each product line is engineered for high current capacity, reliable insulation, efficient installation, and long service life. 1. Enclosed & Insulated Busbar System Our DMMX Enclosed Busbar (also referred to as insulated and protected busbar) is made from highconductivity copper or aluminum conductors with a specially designed insulating housing. It is widely used to transmit and distribute electrical energy from generators, transformers, or rectifiers to industrial equipment. Enclosed busbars can effectively replace traditional cables and cable tray systems in plants, reducing installation complexity and cutting power distribution costs by 30–50%. Rated current: up to 4000A Voltage: 380V/660V Features: large current carrying capacity, excellent heat dissipation, compact structure, reliable insulation, and easy maintenance Application: power distribution in factories, workshops, energy plants, and indoor/outdoor industrial environments 2. Busbar / Busway System The Busbar / Busway System consists of metallic strips or bars used for local highcurrent power distribution, typically installed inside switchgear, panel boards, or busway enclosures. With a modular “sandwich” structure and selfpiercing riveting assembly, these systems support flexible electrical layouts and can achieve protection ratings up to IP68 for harsh environments. They provide robust grounding paths and allow flexible tapping points, making them suitable for complex industrial electrical infrastructure. Application: highcurrent distribution in industrial plants, power centres, electrical switchyards, and large machinery installations Advantages: excellent cooling, customizable grounding options, and versatile installation orientations (vertical or horizontal)  More: https://www.demaelectric.com/products.html

The company's newly developed DM-CL Aluminium Cable Festoon Systems is an upgraded alternative to the traditional Steel Cable Festoon Systems, which can be combined with cables and trolleys to form an ideal mobile power supply system. The system has relatively low environmental requirements, runs smoothly does not produce sparks, and can work normally in indoor, outdoor, dusty, and large temperature difference occasions. This Festoon Systems can be widely used in various overhead cranes, gantry cranes, electric hoists, tobacco machinery, and mobile power supply of lifting equipment in the paper industry, warehouses, shipyards, docks, etc.   Why did we choose DEMAELECTRIC?   Product structure Modular design, quick installation, saving 50% construction time. Production workshop A. Own clean workshop to prevent dust from entering. B. 5S management. Processing cycle      A. For products with unusual usage, after the raw materials are put into storage, we will work overtime to schedule production based on the customer's schedule, ensuring both quality and quantity, to ensure the user's installation schedule. B. We have established long-term cooperative relationships with logistics companies to ensure efficient and safe operation. Implementation standards A.  Benchmark the quality of imported products and continuously improve the application scope and application environment of products. B. Raw materials must have a certificate of conformity when entering the site, and debris is not allowed.  More: https://www.demaelectric.com/products.html

DMHP enclosed conductor Bar（Open Monorail Systems) adopts polymer polyvinyl chloride housing, embeds a plurality of transmission copper conductors as transmission bus, and is equipped with a flexible multi-pole brush current collector, which is simple and compact, safe and reliable. Enclosed conductor bar are widely used in cranes and other electrical equipment.Copper instead of steel as a transmission conductor can save 15%~20% of electric energy, and greatly save materials and installation costs. Easy to install and maintain. Now it is widely used in factories and mines, warehouses, stations, ports, and terminals of lifting machinery, such as electric hoists, cranes, elevators, automatic production lines, and other mobile electrical equipment.   Certificate We have professional certificate like: CE Certificate, ISO9001 Quality Certificate, ISO14001 Environment Certificate, ISO45001 Health&Safety Certificate etc. The specific details can be confirmed through the certificate section of the website. Features Enclosed Conductor Rail System: The Future of Efficient Power Distribution In the fast-paced world of modern industry, dependable power distribution is critical to maintaining productivity and ensuring safety. The Enclosed Conductor Rail System emerges as a revolutionary solution for industries ranging from manufacturing and warehousing to transportation and entertainment. Designed with innovation, durability, and efficiency in mind, this cutting-edge system is set to redefine how power is delivered to mobile applications. Overview of the Enclosed Conductor Rail System The enclosed conductor rail system is an advanced electrical distribution solution that utilizes a robust, insulated rail housing to safely and efficiently deliver power to a variety of equipment, vehicles, and machinery. Unlike traditional open conductor systems, which expose wiring and components to environmental hazards, the enclosed design offers enhanced protection against dust, dirt, moisture, and other potential contaminants. This system is engineered to support heavy loads while maintaining minimal maintenance needs—a critical factor for businesses looking to optimize their operations. Its modular design allows for easy configuration and adaptability, enabling you to scale your power distribution as your needs evolve. More: https://www.demaelectric.com/products.html

2BE-type water-ring vacuum pump and compressor is a high-efficiency, energy-saving product developed by our company based on years of scientific research achievements and production experience, combined with advanced technologies from international counterparts. It is typically used to extract gases free of solid particles, insoluble in water, and non-corrosive, thereby creating vacuum and pressure within sealed containers. By altering the sealing material, it can also be employed to extract corrosive gases or utilize corrosive liquids as the working medium. The 2BE-type water-ring vacuum pump is widely applied in industries such as papermaking, chemical, petrochemical, light industry, pharmaceuticals, food, metallurgy, building materials, stone processing, coal washing, mineral beneficiation, and fertilizer production. The 2BE type water-ring vacuum pump adopts a single-stage single-action structural design, featuring advantages such as simple structure, easy maintenance, reliable operation, high efficiency, and energy savings. It can also adapt to harsh working conditions such as large drainage capacity and load impact fluctuations. 　　 We conducted systematic optimization design for key components of the 2BE-type water-ring vacuum pump, such as the distributor plate, impeller, and pump shaft. This simplified the structure and improved performance, achieving energy savings. The impeller features welded construction, with blades formed through one-time stamping and shaping, ensuring rational contour lines. All machining processes are completed, fundamentally resolving dynamic balance issues. The impeller and pump shaft adopt a thermal assembly interference fit, ensuring reliable performance and smooth operation. After welding, the impeller undergoes comprehensive heat treatment, giving the blades excellent toughness. This fundamentally guarantees the blades' impact and bending resistance, enabling the 2BE-type water-ring vacuum pump to adapt to harsh working conditions with load impact fluctuations. The 2BE-type water-ring vacuum pump comes with a built-in air-water separator and multiple discharge ports. The pump cover features an inspection window for the exhaust valve. The clearance between the impeller and the distributor plate is adjusted via the positioning shaft's end covers. It offers convenient installation, simple operation, and easy maintenance.

Minimum Order: 1 bags

PWDDFL-type multi-suction head sludge pump features an impeller with single/double flow channels and double/multi-blades, employing high-efficiency, clog-free hydraulic design for excellent flow performance. It boasts a compact structure, small footprint, smooth operation, minimal vibration, high reliability, simple installation, and user-friendly operation. When paired with our company's electrical control cabinet, it enables automatic control functions. In addition to the common traits of centrifugal pumps, the multi-suction head vertical silt-free sludge pump possesses three unique advantages: 1. Multiple Suction Heads. Each pump is equipped with 3 or 4 suction heads, distributed across the center and corners of the sump pit. This design ensures high suction head redundancy, extensive water intake range, and reduced pit sedimentation. 2. Integrated Agitation: A mixer is installed beneath the primary suction head, stirring up settled materials in the pit to effectively prevent clogging and silt accumulation. 3. Self-Supporting Design。 Unlike other vertical sewage pumps that require brackets fixed to pre-embedded supports (which complicates both installation and maintenance), the multi-suction head pump uses its side suction heads as both intake points and structural supports. No additional installation is needed—simply place the pump in the pit and connect the discharge pipe for stable operation, with easy maintenance. This pump is primarily suitable for industries such as power plants, steel mills, coal mines, chemical plants, pharmaceuticals, municipal engineering, construction, hospitals, hotels, seawater drainage, rural biogas tanks, and agricultural irrigation. It can also handle the pumping of sludge, wastewater, urban domestic sewage or rainwater, and clean water containing solid particles or long fibers etc.

Minimum Order: 1 bags