Offers to Sell

The bare board test probe is used for bare board (blank version) testing. To check the operation of a PCB circuit, the test probe is generally applied with the receptacle as the conduction confirmation and inspection of a circuit substrate to examine the fixture, analyze the completeness of the circuit, and inspect specification requirements of the circuit footprint, to ensure proper function of various circuits on PCBs. Specification: 1. Recommended min. center: 2.54 (0.1") 2. Full travel: 4.2(0.165" ) / 2.54(0.1" ) 3. Current rating: 3A 4. Contact resistance: 30mΩ 5. Spring force: 150g Materials and finishes: 1. Plunger: Sk4 / PhBr / NI plated 2. Barrel: Brass , Gold plated 3. Spring: Stainless Steel

The bare board test probe is used for bare board (blank version) testing. To check the operation of a PCB circuit, the test probe is generally applied with the receptacle as the conduction confirmation and inspection of a circuit substrate to examine the fixture, analyze the completeness of the circuit, and inspect specification requirements of the circuit footprint, to ensure proper function of various circuits on PCBs. Specification: 1. Recommended min. center: 1.27 (.050") 2. Full travel: 2.54 (0.1") 3. Current rating: 1.5A 4. Contact resistance: 70mΩ 5. Spring force: 30g / 60g / 80g / 120g Materials and finishes: 1. Plunger: Sk4 / PhBr / NI plated 2. Barrel: Phosphor bronze, Gold plated 3. Spring: Stainless Steel

Optical laborers select high-quality optical glasses, including N-BK7, Fused Silica and sapphire. Through manual and precision instrument processing, optical domes for harsh environments are produced. Optical glass domes are corrosion resistant and high-pressure resistant. They are often used in underwater photography and underwater detection, meterological station measurement and military missiles, as a protective cover to protect sensitive sensors and detection equipment. N-BK7 Domes N-BK7 has good transmittance (400nm-1550nm) in the visible and near-infrared spectrum. N-BK7 is a common optical material with low cost and high performance. The refractive index is highly consistent. There are fewer bubbles and streaks in N-BK7. N-BK7 domes are used for solar pyrgeometers to protect the detector from rain and snow. Besides, they prevent harsh environments from affecting the sensitivity of the detector. In addition to the commonly used N-BK7 Domes, RZ Optics Co., Ltd. also produces optical domes made of fused silica and sapphire. Fused Silica Domes Fused silica is often used in the ultraviolet spectrum, between 185-2500nm, with good transmittance. Fused silica has high chemical purity, corrosion resistance and high mechanical properties. It withstands temperature changes. It is not easy to deliquesce. Fused silica domes are used as a protective cover for underwater detectors and underwater robots to protect their optical imaging systems. In addition, high-precision optical domes hardly affect the imaging effect of underwater detection equipment. Sapphire Domes Sapphire is a stable infrared material, anti-corrosion and anti-deliquesce. Under the same thickness, the performance of sapphire is better than optical glass and quartz glass, but the price is slightly more expensive. Sapphire domes are often used as a protective cover for deep-sea optical imaging systems and guided missiles due to its stable chemical properties, strong pressure resistance and better capabilities of transmission. RZ Optics Co., Ltd. produces custom optical glass domes, according to your requirements. We strictly control the parameters of optical glass domes to ensure the precise design of each batch of custom optical glass domes. For more information, please contact us.

RZ Optics Co., Ltd. provides custom optical domes that meet applications of customers. Our company produces optical domes made of optical glass, quartz glass, sapphire and silicon. Our company specializes in processing optical domes for deep-sea exploration, underwater exploration and meteorological exploration. Optical domes produced by our company are used as a window for underwater cameras and underwater robots. They are resistant to seawater corrosion and high pressure. They are also used for meteorological pyrgeometers as protective covers. RZ Optics Co., Ltd. provides optical glass domes with commercial quality and high precision quality, including N-BK7 domes, Fused Silica domes, Sapphire domes and Silicon domes. The diameter of custom optical glass domes can be 15-280mm. The highest accuracy of concentricity can be less than 0.02mm. The highest accuracy of surface quality can be 40-20. How can you get custom optical domes? Please send us design drawings or custom parameters, including diameter, optical material and surface quality. Don't forget to add the requirement of quantities and lead time. Of course, the simplest way is direct to contact us for more information. N-BK7 Domes N-BK7 has good transmittance (400nm-1550nm) in the visible and near-infrared spectrum. N-BK7 is a common optical material with low cost and high performance. The refractive index is highly consistent. There are fewer bubbles and streaks in N-BK7. N-BK7 domes are used for solar pyrgeometers to protect the detector from rain and snow. Besides, they prevent harsh environments from affecting the sensitivity of the detector. Fused Silica Domes Fused silica is often used in the ultraviolet spectrum, between 185-2500nm, with good transmittance. Fused silica has high chemical purity, corrosion resistance and high mechanical properties. It withstands temperature changes. It is not easy to deliquesce. Fused silica domes are used as a protective cover for underwater detectors and underwater robots to protect their optical imaging systems. In addition, high-precision optical domes hardly affect the imaging effect of underwater detection equipment.  Sapphire Domes Sapphire is a stable infrared material, anti-corrosion and anti-deliquesce. Under the same thickness, the performance of sapphire is better than optical glass and quartz glass, but the price is slightly more expensive. Sapphire domes are often used as a protective cover for deep-sea optical imaging systems and guided missiles due to its stable chemical properties, strong pressure resistance and better capabilities of transmission.

The biconvex lens is a convergent lens with two outwardly curved surfaces, which are symmetrical. Its radius of curvature is equal. The spherical aberration, coma and distortion of biconvex lenses reach the minimum. In addition to controlling laser beams in lasers, biconvex lenses are also used for optical imaging systems or other optical instruments. N-BK7 Bi-Convex Lenses N-BK7 (Equivalent Material CDGM H-K9L) is crown glass with a transmission range of visible light and near-infrared spectrum (350nm-2000nm). N-BK7 possesses excellent optical, mechanical and chemical properties and is cost- effective. N-BK7 double convex lenses are often used in various optical imaging systems. Fused Silica Bi-Convex Lenses Between 185-2500nm, fused silica biconvex lenses have good transmittance. Fused silica has stable chemical properties, high-temperature resistance, low laser damage threshold. It is suitable for laser optical systems. Silicon Bi-Convex Lenses Silicon has metallic luster and is blocked in the visible light band. It has good transmittance in the infrared band (3-5μm). As a commonly used infrared optical material, silicon has high refractive index and small dispersion. Silicon lenses are widely used in infrared missile optical systems.

Plano-convex lenses are positive focal length elements with one spherical surface and one flat surface. These lenses are designed for infinite conjugate (parallel light) use or simple imaging in non-critical applications. These optics are ideal for general purpose focusing elements. Our lenses are ideal for a variety of applications, from industrial, robotics, pharmaceutical to defense. Esco manufactures plano-convex lenses using S1-UV grade fused silica, G1 fused silica, commercial grade and BK7 optical glass. Each optic is pitch polished to provide good surface quality and excellent low-cost imaging performance for a wide range of light sources. When plano convex lenses are used for laser cutting, they are best suited for high-turnover cutting applications and when cutting thick materials. In these cases, the plano-convex lens provides a larger cut width, which allows the laser's oxygen-assisted access to cut and aid in the cut. Plano convex lenses also provide greater depth of field, which helps create tapered edges.

Plano-Concave Lenses have edges that are thicker than the center and flat on one side. Plano-concave lenses are used to expand a light beam or increase the focal length in an optical system. They are commonly used for beam expansion of high peak power pulsed lasers. The beam incident on the concave surface will be focused to a point outside the instrument. Unwanted air heating and ionization at the focal point may accompany mode disruption or material damage. To avoid this problem, the input lens should be inverted so that the concave surface is not facing the parallel beam. Material selection: optical glass, laser crystal, fused silica, anti- radiation glass, infrared and ultraviolet materials, metal materials Strict dimensional control standards custom coating Wide selection of RZ spherical lenses made of N-BK7, UVFS or CaF2 optical materials, spherical lenses made of N-BK7, UVFS or S-LAH64 optical materials, cylinders and cones (shafts) made of N-BK7 and UVFS cone) lens. The lens forms are plano-convex, plano-concave, double-convex, double- concave, plano-convex cylinder and plano-concave cylinder. Focal lengths vary from -5000 to +10000 mm. Other specific materials, sizes and anti-reflective (AR) coated lenses are available upon request. Factory Standard Shape: Plano-Concave Diameter Tolerance: ± 0.05mm Thickness Tolerance: ± 0.05mm Radius: ± 0.3% Focal Length Tolerance: ± 1% Surface Quality: 40-20 Scratch-Dig(After Coating) Surface Flatness: λ/4 @633 nm Centration: < 3 arc minutes Clear Aperture: > 95% of central dimension

Super Soft Vibrator And Hot Sales G-spot Massager Wand Sex Toy Woman Vibrator Brand Name xese / OEM Type Sex Product Model Number AV-28 Color Red/Purple/Black Material Medical Silicone Size 38*165mm Power Supply 3.7V/500mAh Weight 200g Vibration 20*3 Multi-Speeds Waterproof Yes Product Name Japenese Sex Wand Certificate CE ROHS

Sopran Ice Platinum Hair Removal 755nm 808nm 1064nm Laser Sopran Ice Titanium Laser 808 Diode Laser Working Principle The diode laser device uses 4 waves 1064nm +808nm + 755nm+940nm, which has special effectiveness for melanocytes of hair follicle without any damage to the surrounding tissues. The laser can be absorbed by melanocytes of hair shaft and hair follicles and converted into heat to increase the temperature of hair follicle. When the temperature rises to certain level that can irreversibly destroy the structure of hair follicle, the hair follicle structure will disappear after a natural physiological process of the hair follicle, thereby achieving the purpose for removing hair permanently Machine Features: 1. USA Coherent laser bars , 100million shot, 2. Bigger power: ensure faster and better hair removal result , Real painless and permanent,hair removal, 3. Big spot size: 12*20mm /12*35mm ,bring fast hair removal , 4. Fast cooling: TEC part on handle , can reach -29℃. bring comfortable feeling when doing treatment , Handle Details: 1. 755+808+1064nm Style Technology. 2. The 3 waves works in the same handle at the same time: 3. 755nm for white skin( fine, golden hair) 4. 808nm for yellow/neutral skin 5. 1064nm for black(black hair)

The BTC miner machine's algorithm is 140T and its power consumption is 3010w. It has 4 fans so hat it can cool the machine. There is no need to consider what should we do if the temperature is too high. And the noise level is 75db. The total weight of the Btc Miner Machine S19xp 140T is 16kg, and the packing details is 570*316*430mm. The BTC miner machine S19xp 140T is mainly composed of 3 computer boards, 1 control board, APW12 power supply, 4 heat dissipation fans, and 114 chips. The BTC miner machine S19xp still is used 7NM chip, but the performance is better than the T17 series in terms of performance and stability, and the lines of this machine is not easy to break. It uses the SHA-256 algorithm, with a maximum hash rate of 140TH. The hashrate is large enough to almost guarantee huge profit margins. This BTC miner machine supports ASIC, which means you can monitor mining progress when you are out. Miners should also pay attention to the Market Place and VIABTC tokens under the SHA-256 algorithm. These two are most likely to be the top tokens mined by the platform. Product name Antminer S19xp 140TH/S Algorithm SHA256 Hashrate 140T , Power Consumption 3010W±5% Release May 2020 Size 570*316*430mm Weight 16000g Noise level 75db Fan(s) 4 Power 3010W Interface Ethernet Temperature 0-40 °C Humidity 5-95 %

GT15 454159-5002S 038145701A 038145701AX 038145701AV 038145701D turbocharger for AGR/TDI 90 engine Size: 39*31*40cm Turbo Model: GT15 Condition: New Type: Turbo charger Automobile manufacturing: car Application: 1996-98 Audi A3 1.9 TDI (8L) Engine AGR 1997-00 Skoda Octavia I 1.9 TDI Engine AGR 1997-01 Volkswagen Bora 1.9 TDI Engine AGR 1997-01 Volkswagen Golf IV 1.9 TDI Engine AGR Product Details Generally speaking,turbocharging is a great idea.it's a smaller engine,but you're still getting a decent amount amount of power,"says Mike Quincy,autos editor at Consumer Reports."The idea with a smaller engine,especially a four- cylinder,is that you're going to get decent fuel economy without giving up power, APPLICATIONS 1996-98 Audi A3 1.9 TDI (8L) Engine AGR 1997-00 Skoda Octavia I 1.9 TDI Engine AGR 1997-01 Volkswagen Bora 1.9 TDI Engine AGR 1997-01 Volkswagen Golf IV 1.9 TDI Engine AGR

Product Name: pregabalin Pregabalin wj1@gzwjs , w.com whatsapp +8615512123605 signal +66980528100 Synonyms: 3(S)-(AMINOMETHYL)-5-METHYLHEXANOIC ACID;(3S)-3- (AMINOMETHYL)-5-METHYLHEXANOIC ACID;PREGABALIN;Pregablin;3-(Aminomethyl)-5- me , thyl-hexanoic acid;PREDNISOLONESODIUMPHOSPHATE;(R)-Pregabalin;(S , )-Pregabalin CAS: 148553-50-8 MF: C8H17NO2 MW: 159.23 EINECS: 604-639-1 Mol File: 148553-50-8

Music wire is a tough wire material with high tensile strength most widely used for piano and other musical springs. It can withstand higher stresses under repeated loading than other spring materials. We supply high quality music wire of high-carbon steel wire to specification ASTM A-228, offering high tensile strength and excellent fatigue life. Our musical spring wire is available in various plating and surface treatments. Materials: Stainless, Carbon Steel Finishes: Bright, galvanised, tinned, phosphated Music Spring wire as per EN-10270-1 / ASTM A 228 or Equivalwnt Dia: 0.20 to 0.63mm Music wire for spring as per EN 10270-1 / ASTM A228 Fine wire diameter: Fine Music Spring Wire exported to India Wire dia 0.20, 0.22, 0.25, 0.28, 0.30, 0.36, 0.38 and 0.63mm Various wire sizes are available for different uses. Music wire is manufactured of standard and custom steel wires for various uses: Musical, fasteners, springs, windings, and etc.

We supply steel galvanized wire, hot dipped or electro galvanised. Hot Dipped Galvanised Wire is processed by steel rod through wire drawing, heat treatment and zinc plating. Hot dipped galvanised wire is a heavily galvanized wire through melt zinc coating process achieving excellent flexibility and softness. The thick zinc coating of hot dipped galva. wire offers better corrosion resistance over electro galvanized wire at a higher cost. Application: As trying wire in agriculture for vines and orchards, as weaving wire of galvanized wire mesh, hardware cloth, welded mesh in the fencing and netting industry, as material for manufacture of springs, nails, ropes, wire forms, packaging of products and other daily uses. Raw Material: SAE 1006 -1070 Diameter of Wire: 1,40 - 4,00 mm Tensile Strength:350 - 1800 N/mm2 Weight of Coil: 100 - 900 kgs Hot Dipped Galvanised Steel Wire dia 2.9mm, 2.3mm, 2.0mm and 1.6mm is popularly used for spring and tie wire, hot dipped galvanized steel wire with pvc coating for binding has a popular dia 2.0mm and 1.6mm. 5mm High Tensile Strength Hot Dipped Galvanized Steel Wire Type: Bare Form: Stranded wrie Application: Overhead guy wire / stay wire Conductor Material: Galvanized Steel Wire Sheath Material: Bare Insulation Material: Bare Material Shape: Round Wire Standard: ASTM,BS,IEC,DIN Color: Silver Application The galvanized single steel wires or stranded steel wires are suitable for cores of ACSR to improve its tensile strength. Also used in the aerial transmission line as the line material of ground connection to avoid the lightning strike as Messenger Wire, Overhead Ground or Static Wire, Guy Wire. Construction Stranded galvanized steel wire is made of carbon steel hot dipped zinc plated. The single wires are concentrically stranded and wrapped helically around a central wire. Standard ASTM A475: Standard Specification for Zinc-Coated Steel Wire Strand ASTM B 498: Standard Specification for Zinc-Coated (Galvanized) Steel Core Wire for Aluminum Conductors, Steel Reinforced (ACSR) BS183: Specification for General Purpose Galvanized Steel Wire Strand BS 50189: Conductors ofr overhead lines-Zinc coated steel wires IEC 60888: Zinc-coated steel wires for stranded conductors DIN 48200: Wires for stranded conductors JIS G 3537: Zinc-coated steel wire strands AS 1222.1: Steel conductors and stays-Bare overhead