Offers to Sell

The car air filter commonly used in passenger fuel vehicle engines mainly have paper air filter and polyurethane air filter. Paper air filters are made of microporous filter paper treated with resin. The filter paper is porous, loose and folded. They have certain mechanical strength and water resistance with advantages of high filtration efficiency, simple structure, light weight, low cost and convenient maintenance. They are most widely used as vehicle air filters at present. Polyurethane car filter are made of soft, porous and spongy polyurethane with strong adsorption capacity. They have the same advantages of paper air filters, but also have low mechanical strength. What Are the Symptoms of a Bad Air Filters? The auto air filters is a device for removing particulate impurities in the air. If the air contains dust and other impurities, will aggravate the wear of engine parts, so air filter with good performance must be installed into the vehicle. The main requirements of the air filter are high filtration efficiency, low flow resistance and continuous use for a long time without frequent maintenance. In case of damage or blockage, the following phenomena will occur. Acceleration performance decreases and fuel consumption increases. Once the filter element is blocked, there is too much dust and the aperture of the filter paper is blocked, will hinder the passage of air. Then the air intake rate will decrease, the air flow will decrease, and there is not enough air support when the engine burns. Even if the accelerator is pressed deeply, the speed still can not come up, there will be insufficient power and the driving fuel consumption will increase. Moreover, under the strong negative pressure (intake suction) of the engine, the dust, impurities and particles outside the filter element will break through the filter paper and directly enter the cylinder to participate in combustion, even lead to the breakage and rupture of the filter paper. The engine emits black smoke. If the automobile air filter is damaged or not replaced and cleaned for a long time, the dust will directly enter the engine and pass through the throttle. At this time, the particles in the air are like grinding sand, which will cause wear to the throttle. After the throttle is worn, it will sink, reduce the compression ratio and air leakage, resulting in the reduction of engine cylinder pressure, hard to start and low combustion efficiency. The cylinder burns insufficiently, the exhaust pipe emits black smoke and presents a divergent shape, and the air flow has no impulse. As one of the most professional car spares suppliers, we provide automobile air filter, auto spares sale, pencil coil, etc. For air filter car cost or more information, please feel free to contact us!

Minimum Order: 1 bags

Car air conditioning system is a device that realizes cooling, heating, ventilation and air purification of the air in the vehicle. It can provide a comfortable driving environment for driver and passengers, especially reduce the driver's fatigue strength, and improve driving safety. The air conditioning unit has become one of the indicators to measure whether the vehicle is fully functional. Modern vehicle air conditioners have four functions, any of which are designed to make driver and passengers comfortable. The air conditioner can control the temperature in the cabin, both heating and cooling the air, to make the cabin has comfortable temperature. The air conditioner can discharge the moisture in the air. Dry air absorbs human sweat and creat a more comfortable environment. The air conditioner has functions of inhale fresh air and ventilation. The air conditioner can filter the air to remove dust and pollen. How Does The Air Conditioning System (A/C) Work? Automotive air conditioning is mainly composed of refrigeration system, heating system, ventilation and air purification system and control system. The principle of automotive air conditioning has four sections. A, The compressor sucks the low-temperature and low-pressure refrigerant gas at the outlet of the evaporator, and compresses it into high-temperature and high-pressure gas and discharges from compressor. B, The high-temperature and high-pressure refrigerant gas enters the condenser and condenses into a liquid, discharges a large amount of heat. C, The refrigerant liquid with high temperature and high pressure increases in volume after passing through the expansion device, the pressure and temperature drop sharply, then discharged from the expansion device in the form of a mist. D, The mist-like refrigerant liquid entering the evaporator, the boiling point of the refrigerant is much lower than the temperature in the evaporator, and the refrigerant liquid evaporates into a gas. Diagram of Air Conditioning System (A/C) The automotive air conditioning refrigeration system consists of a compressor, a condenser, a liquid receiver dryer, an expansion valve, an evaporator and a blower. The components are connected by copper pipes and high-pressure rubber pipes to form a closed system. When the refrigeration system works, the refrigerant circulates in this closed system in different states. As one of the most professional auto spares suppliers, we provide car air conditioner replacement, car air conditioner gas, car ac unit, car ignition components, car auto spare parts, etc. For car ac unit price or more information, please feel free to contact us!

Minimum Order: 1 bags

Barrel bungs plastic bung is G2 and G3/4'' plug type with ISO-228 thread, can well suit into drum flange on 55 gallon steel drums. It is a substitute for zinc plated drum plug in some cases. Whatever the material is, the bungs are aiming at reducing the risk of spillage and keeping the contents safe The included 2'' and 3/4'' bung fittings make filling and dispensing easy and convenient, the plug wrench is designed to help to screw in and out of the bung fittings. Details of Steel Drum Plastic Bung 1 The raw mateiral of the steel drum plastic bung is made of new polypropylene and selected recycled polypropylene, which maxiumize the useage of the commericals and also keep the final bung in good properties. 2 Not even the most critical thread parts follow the standard, other aspects of the plastic bung is also designed to be similiar to the common types in global market, which enable to well replace other plastic bungs. 3 The gasket selection is based on the containers' contents, the common types are EPDM, NBR and PE gasket applied to the steel drum plastic bung, differenciate from temperature tolerance, chemical resistance. Specification of Steel Drum Plastic Bung Size 2 Inch and 3/4 Inch Material Polypropylene Thread Standard ISO-228 Gasket EPDM, Black Buna, PE Carton Quantity 250 Pieces,1000 Pieces Pallet Quantity 11,250 Pieces, 45,000 Pieces As a professional cap seal manufacturer, we provide barrel fittings, drum closure, etc. For more information, please feel free to contact us!

These steel drum flange and plug come available in zinc plated and phenolic lacquered styles, preventing from various corrosive contents. Closure is equipped with well-formulated EPDM, NBR or PE gasket, the different materials make it perform well under different filling conditions. Dual gasket system is another common choice in European area as two combined washers can seal with better security. The octagonal flange is supposed to riveted on metal drum lid providing a seal base for drum plug to be torqued on, those 2'' and 3/4'' set make up an universal closing system for standard close head drum. It is necessary to have a well- designed paint cap covering on drum lid mouth, preventing the inner side of drum from spraying paints contamination. Secure your drum or barrel during packaging, storage and transport with our steel drum closure! Types of steel drum caps Zinc Plated Drum Flange Zinc Plated Drum Plug Zinc Plated Drum Plug Read More  Lacquered Drum Flange Lacquered Drum Plug Drum Paint Cap  Features of Steel Drum Closure Zinc Plated Drum Flange Octagon zinc plated drum flange is the key base for steel, plastic, nylon plug screwing in. Zinc Plated Drum Plug Fitted with EPDM, Buna or PE gasket, drum plug plays the initial guard ensuring fillings integrity. Lacquered Drum Flange Painted drum flange is selected for drum while there is more corrosive content within. Lacquered Drum Plug G2 and G3/4 drum plug treated with lacquer, is often chosen for special chemicals or food grade products. Drum Paint Cap Avoid of interior contamination, drum paint caps are efficient protective caps during drum painting process. How To Use Steel Drum Closure? Drum flange needs to be riveted onto drum top by flange insertion die before using. It forms a base for drum plug to screw in after drum flange riveted. Customers could choose steel drum plug, plastic drum plug or nylon plug based on contents in the drum. Appropriate torque is essential while screwing drum plug, excess or lack of torque will lead to leaking risks of the container. After both drum flange and plug are properly installed, it forms a sealing system for drum. Flange riveting is crucial in terms of final sealing results. Regular maintenance or replacement of insertion die is necessary to keep riveting quality. Key parameters, including insertion die abrasion and flange height after riveting, need to be checked if problems occur. As a professional cap seal company, we provide drum bung fittings, drum closure, steel drum bung, metal bung, metal drum plugs etc. For more information, please feel free to contact us!

The airbag sensor is the input device of control signal in the SRS system. When the vehicle happens to collides, the airbag sensor detects the intensity signal of the vehicle collision, and inputs the signal into the airbag computer. The airbag computer determines whether to detonate the inflatable element to inflate the airbag according to the signal of the airbag crash sensor. How To Test airbag front sensor? 1) Symptoms of airbag system failure are difficult to diagnose, so diagnostic codes are the most important source of information for troubleshooting. Always check the diagnostic codes before disconnecting the battery. 2) Disconnect the ignition switch during inspection. If the vehicle allows to remove the negative electrode of the battery, it is better to disconnect the power supply. It should be started after removing the negative electrode for 90s or longer. Because the airbag system is equipped with a backup power supply, the airbag may still deploy within 90 seconds after removing the negative terminal of the battery. 3) Even if only a minor collision occurs and the airbags are not deployed, the front airbag pressure sensor and steering wheel cushion should be checked. 4) Do not expose the front airbag impact sensor, center airbag sensor assembly and steering wheel pad directly to hot air and flames. 5) When testing the circuit, a high-impedance multimeter should be used for measurement. 6) The parts of the airbag are attached with instruction labels, and the listed precautions should be strictly followed during operation. 7) After pulling out the airbag wiring plug, use a small copper wire to short the airbag connector. 8) Do not measure the resistance of the detonator tube of the airbag inflation element, so as not to cause the airbag system to explode by mistake. The method of decomposing the inspection parts should be adopted first, and then searching step by step. 9) The airbag system is a very sensitive device. A little carelessness during inspection may detonate the airbag and cause unnecessary losses. 10)The wire harness and connector of the airbag system are generally covered with a special color sleeve, which is different from other system wire harnesses. Do not damage these bushings during inspection. As a professional auto spare parts supplier, we provide car ignition components, car ignition coil, etc. For impact sensor price or more information, please feel free to contact us!

Minimum Order: 1 bags

Plastic spout caps are commonly used in small metal or plastic containers. Its main function is to help dispense liquid products accurately. The major characteristic of this cap is its flexible spout. The applications of plastic spout caps include oil packaging, paint packaging and chemical packaging. Design of these flexspout caps varies depending on types of containers and contents inside. A common plastic spout cap is made up of two parts, one part is the pull ring cap on top and another part is the fexible spout below. There are usually different colors of plastic spout cap to choose from for customers. Types of Plastic Spout Cap Spout Cap for Oil Tin  Features of Plastic Spout Cap Spout Cap for Oil Tin Commonly used for small containers, and it has push-on design. Spout Cap With Ring Used for containers with relatively large volumes, metal ring needs to be crimped to ensure sealing function. How to Use Plastic Spout Cap Spout cap for oil tin is usually designed to have push-on function. Size of the spout cap needs to be the same as the container opening to ensure the best sealing function. Crimping tool is necessary to install the flexspout cap with metal ring. Proper crimping will fix the spout cap firmly, and prevent leaking of contents inside. When opening a container with flexspout cap, the first step is to pull the ring on cap and pull out the mouth. Then rotating and removing the cap on the flexible spout top. After desired liquid is poured out, put back the cap and then push the flexible spout back. As one of the most professional spout cap manufacturers, we provide barrel fittings, drum closure, drum lock seal, spout cap, etc. For more information, please feel free to contact us!

The plastic drum seals are polypropylene made cap seal, designed to lock directly onto plastic bung on HDPE drum barrels under specification guidance. These two combined to be the basic cap system for tight head poly drum, either with 2'' and 3/4'' NPT openings or with 2'' NPT and 2'' buttress openings. Same as other types of drum cap seal, the plastic drum seals protect the filling content from contamination and pilferage. Details of plastic barrel cap 1 The snap on style expresses the application convenience to the users. These plastic drum seals are a more easily operated type than metal cap seals. They are tool free to cover and remove such plastic drum seals. 2 There are red, blue and white under selection. General type of distinguishable red color seals can alert the drum owner once the cap is opened or removed. There is a potential change in the filling content. 3 Variety of the size makes the plastic drum seals fit the diameter differences for HDPE drums. Customers can always find a suitable dimension with us! As one of the most professional spout cap manufacturers, we provide barrel fittings, drum closure, drum lock seal, spout cap, etc. For more information, please feel free to contact us!

The airbag clockspring is a piece of wire harness that connects the main airbag to the airbag harness. Since the main airbag needs to rotate with the steering wheel, when the steering wheel is turned left or right, the wire harness cannot be pulled off, so the connecting wire harness must be left with a margin, and it is necessary to ensure that the steering wheel is turned to the limit position to one side without being pulled off. Key Features of Airbag Clockspring  An important part of connecting the electrical appliances between on the steering wheel and steering column. Can be rotated infinitely. Connect the main airbag to the airbag harness. How To Test Airbag Clockspring？ If the horn does not sound, first unplug the horn, connect the test light, press the steering wheel. The test light does not turn on, check the fuse and relay, if the relay does not respond when pressed, remove the airbag, and directly put the horn button wire is grounded. If the horn sounds, ground the horn wire above the airbag clockpring. If the horn does not sound, check the airbag clockpring, and use a multimeter to measure the continuity of the wire. The airbag light is on. Under the computer test, if it shows that the driver's airbag is disconnected, remove the airbag. If the wiring harness is well, unplug the main airbag and use a 2 ohm resistor to put it into the airbag tap. Clear the fault code. If it can be cleared, it means that the airbag is faulty. It cannot be cleared. Pull the airbag clue below the clockspring wire, connect the 2 ohm resistor, and clear the fault code. If it can be cleared, the clockspring is broken. If it cannot be cleared, check the wiring harness from airbag computer to clockspring. The audio control buttons are generally not broken, the faulty probability is very low, have the same inspection steps. About abnormal noise. You can remove the clockspring and test the vehicle again. It must be replaced it if there is no abnormal noise after removing it. As a professional auto spare parts company, we provide clock spring on steering wheel, clock spring triton, car ignition components, clock spring steering wheel, auto ignition coil, etc. For clock spring price or more information, please feel free to contact us!

Minimum Order: 1 bags

Plastic drum cap seal is available in a different size and dimensional design catering to the application on 55 gallon drum or poly drum.The plastic drum cap seal would be installed on the opening neck manually more easily than metal drum cap seal, what is also called push on, push lock or snap on. The 2'' and 3/4'' EZ plastic drum cap seal is normally in plain white or transparent color for steel barrels, while the plastic drum seal in 78mm, 80mm, 82mm etc are in red, blue or white color for poly drums. The plastic capseal is acting as a safe guard over the round bung keeping away from water, dust and theft from outter environment. Chongyi is able to make a customized logo on the plastic cap seal even with a small MOQ, which enables your property to be more distinguished. Types of Plastic Drum Cap Seal Push On Cap Seal Plastic Drum Seals  Features of Plastic Drum Cap Seal Push On Cap Seal The G2 and G3/4 standard size push on cap seal are with two types of tamper- proof with strong security cap, and dust-proof with cost-effectiveness cap, are under selection. Plastic Drum Seals Variety in dimension and color makes XEAL plastic drum seal meet the most demanding of the poly drums. The seals shall be destroyed once they need to be opened, that is how it is marked as tamper proof. How to Use Plastic Drum Cap Seal The plastic drum cap seal is over the steel plug or plastic bung on the drum neck. It is necessary for users to tell the neck diameter of the HDPE drums, while the steel drum necks are standardized to be G2 and G3/4. General type of cap seal can be put on neck by hand push, one special type of plastic cap seal with ring needs to be crimped tightly by crimping tool. When opening the seals, a removal tool is required to tear it off for the strong cap, while another more conventional type can be removed by hand as well. As one of the most professional cap seals suppliers, we provide barrel fittings, drum closure, drum bung seals, etc. For more information, please feel free to contact us!

Plastic barrel bung plugs has different sizes and thread designs to meet varied sealing requirements of steel drums and plastic drums. Steel drum requires plastic barrel plugs with fine thread, and it needs to follow the same standard as steel drum plug. Plastic drums usually require 2'' and 3/4'' NPT or 2'' NPS or 2'' buttress plastic bungs. Most common raw mateial for plastic drum plug is PP, and nylon material is made for flammable and explosive proof purpose. Type of gasket used is determined by contents within the drums. There are high temperature, chemical, oil resistant gaskets that come with the plastic bungs. Types of plastic drum plugs Steel Drum Plastic Bung Buttress Plastic Bung  Features of Plastic Bung Steel Drum Plastic Bung Standardized in size of 2 inch and 3/4 inch, steel drum plastic bung is suitable with standard steel drum flange. Nylon Drum Bung Special property of nylon drum bung allows it soften and pop out under the relieving pressure from the steel drum. Buttress Platic Bung Varied in size and design, buttress platic bung needs to be selected according to HDPE drum design. How to use Plastic Bung It is necessary to understand the neck mouth type and filers in tight head steel drum or plastic drum, and figure out whats is the suitable thread and gasket of the plastic bung choice for your drum. Any improper factor will reduce sealing performance. Drum wrench needs to be used while screwing the drum plug, applying proper torque assures the contents is well secured. Metal drum cap seal or plastic drum caps seal needs to be installed, aiming at double securing the inner contents as well as the neck mouth. As one of the most professional plastic bungs suppliers, we provide drum bung fittings, drum closure, drum bung fittings, etc. For more information, please feel free to contact us!

High Speed CNC EDM Wire Cut Machine is also named as the CNC High Speed Wire Cut EDM Machine or Fast Speed CNC Wire EDM or High Speed Wire EDM (HS Wire EDM). It has no special requirement to the processed metal material properties. In principle, Sanxing Machinery high speed cnc EDM wire cut machine can process all the conductive materials such as super-hard and hard alloy, quenching materials, stainless steel ductile materials, various magnet steel fragile materials, uneasily-clamped thin wall spares etc. High Speed CNC Wire Cut Machine DK7732C2 with controller integrated & semi enclosed cover, is our most advanced high speed CNC Wire Cut machine. Compared to the Medium Speed CNC Wire Cut Machine, it has the more competitive price. FEATURES OF CNC EDM WIRE CUT MACHINE – DK7732C2 A. Semi Enclosed Cover B. Fixed Wire Drum (Patent: No.200710019393.0) C. Autocut Software + Windows Operation System D. Controller Integrated Type E. Linear Guideway Made By Taiwan, China or Equal F. Industrial Use Computer or Brand Computer G Auto Wire Tension Tool H. Special Abrasive Nozzle TECHNICAL DATA OF CNC EDM WIRE CUT MACHINE – DK7732C2 Type Unit DK7732C2 Worktable Size mm 650×400 Table Travel mm 400×320 Max. Workpiece Thickness mm 200 Standard Workpiece Accuracy mm ≤0.015 Best Surface Roughness μm ≤2.5 Max. Cutting Speed mm2/min 200 Wire Running Speed m/s 5-11.5 Taper °/mm 6°/100(Bigger Tapers Optional) Power Input V/Hz 3 phase 380V/50Hz or 220V/60Hz or 415V/50Hz Overall Power KVA 2 PRODUCT DETAILS Product Details of High Speed CNC Wire Cut EDM / CNC Wire EDM / HS Wire EDM / WEDM - Sanxing Machinery OPTIONAL 1. Model: from DK7732C2 To DK77120C2 2. Bigger Taper Optional 3. High Thickness Optional 4. Touch Screen Monitor Optional 5. Different Power input Optional 6. Aluminium Cutting Equipment Optional 7. Servo Motors Optional 8. D.R.O optional COMPARSION OF ALL THE EDM CNC WIRE CUT MACHINE Comparision of High Speed EDM CNC Wire Cut Machine / CNC Wire Cut EDM Machine - Sanxing Machinery DELIVERY TIME 15 days after order confirmation WARRANTY One year During the warranty period, we can provide free parts and components that are not damaged due to improper operation (consumables not included). Out of warranty period, we will supply our best service to you as usual, if you have any question. 1. Offer technical support online service. 2. Technical files service & on-site training service provided. 3. Offer machine operation video. 4. Spare parts replacement and repair service provided. 5. All questions will be replied within 24 hours. FAQ Q: Are you a manufacturer or trading company? A: We are the professional manufacturer of cnc wire cut edm machine, which have been in the industry around 30 years. Q: Can you provide training and maintenance? A: Yes. In order to make your production more efficient, before the delivery, you can send someone to my company for free professional operation training. Q: What information will you need to make the proposal? A: Such as the Worktable size, worktable travel, surface finish, cutting accuracy, and your special requirements. Keywords: CNC Wire Cut Machine, CNC Wire Cutting Machine, CNC Wire Cutter, CNC Wire Cut EDM, CNC Mo Wire EDM, Wire EDM, EDM Cut Machine, High Speed Wire Cut EDM, High Speed Wire Cut Machine, Fast Speed Wire Cut EDM Machine, Controller Integrated Type Cut Machine, Semi Enclosed Wire Cut Machine, DK77C2 Series， DKK7732C2…

Minimum Order: 1 bags

TV Mount Bracket for Sale Wall brackets normally go hand in hand with a TV. Many people are opting for LCD televisions and TV bracket manufacturers are following closely behind with an array of wall mounts to choose from. To appreciate the nature of the brackets and the way it functions in conjunction to the television, we should get an idea of the Liquid Crystal Display (LCD) television. It is a flat panel screen that basically uses the same LCD technology found in cell phones and computer monitors and can be made very thin. The flat and thin aspect provides the opportunity of hanging or mounting the LCD TV on a wall or ceiling through wall mounts. Television sets come in different sizes and weights, and as expected, CNXD concentrates on TV wall mount design to meet the varying sizes and weights. Most people prefer mounting them on walls for better viewing. There is a broad range of wall mounts to fit a specific television brand and model, and there are also generic types that can fit any model within defined sizes and weights. Most, if not all types are easy to install. Here are some types to consider when you get your LCD television. Different Types of TV Mounting Brackets Fixed TV Wall Mount PTS009-1 PTS0017-3 PTS0017-4 PTS , 0017-5 PTS0039 PTS1230 PTS004 PTS004-1 , FIXED TV WALL MOUNT The function is very simple and can only be used to fix the TV. This product has a single function, so the production cost is very low. Priced right for today’s competitive TV wall mount market. Tilt TV Wall Mount PTS003 PTS0025 PTS0011 PTS0011-2 , PTS0017-4T DT200 DT500 DT600 TILT TV WALL MOUNT Free-Tilting Design: makes easy forward or backward adjustment for better viewing and reduced glare. The angle adjustment is added to the original fixed function. Due to the increase of functions, some production costs will be increased. Full-Motion TV Wall Mount WMX015 WMX016 WMX001 WMX002T-5 WMX004 WMX004-2 WMX005 WMX005-1 FULL , -MOTION TV WALL MOUNT Rotating arm: provides maximum viewing flexibility. Full motion TV wall mount has the most comprehensive function. You can adjust the angle of watching TV at will. Any seat will be the best seat. TV Ceiling Mount WMX008 TV CEILING MOUNT Use high-quality steel to keep the product stable and safe. The perfect structural design makes it easy to adjust when carrying two TVs. It allows the display to tilt and rotate around the rod without tools, which is very convenient to use. FAQs of TV Mounts Q How can I know which TV mount is suitable to my TV? There are two main parameters to be fitted: 1. Declared load weight of TV stand - the weight of a TV without a stand should not exceed the declared weight of the TV mount. 2.Back screen connection hole pattern measurement (VESA) - the distance between the four connection holes on the back of the TV shall not be greater than the distance of the TV mounting bracket. The maximum VESA pattern supported by the TV stand is shown on the stand specification. Can I mount a TV on any wall? Important: for your safety and product protection, the wall you choose should be able to hold four times the weight of the TV. The wall you select should fit your viewing preferences. Here are some considerations: Installation height: placing the TV at the line of sight level between the TV screen is usually the preferred viewing height and position. Lighting conditions: light from windows and lamps may cause glare on the TV screen. Viewing distance: the distance sitting in front of the TV is also an important part of optimizing the viewing experience. Corners and non - flat surfaces: these types of surfaces may require specially designed mounting Why get a tilt TV mount? In addition to being clean and beautiful, the inclined wall installation also allows different degrees of vertical adjustment. If your TV is above the best viewing level, this is the best choice, allowing you to tilt the screen down when watching your favorite programs to protect your cervical spine. Will CNXD mounts hold the stated weight? Yes, the CNXD mount has been tested to withstand 3 and 4 times the specified load capacity. In order to ensure absolute safety in actual use, we strictly limit the rated capacity of the product.

Tilt arm tv bracket can be said to be the upgraded fixed TV wall mount. It adds the function of angle adjustment on the original basis. But it still retains the advantages of simplicity and durability. It can fix the TV firmly to the wall and allow you to adjust the angle of watching TV. The tv bracket tilt down adopts open wall panel design, which can be directly installed on the power socket to achieve super clean installation. Use the cable to easily lock and release your TV, and the elegant panel edge can prevent your TV from sliding. Advantages of tv wall bracket adjustable tilt  Save space Frees up floor space Open architecture Hidden cords and wires Free tilt design Easy angle adjustment to get better viewing effect and reduce glare How to Install Tilt Fixed TV Wall Mount Hook installation is simple and convenient. Free tilt design for better viewing and reduced glare. Ultra-thin design brings beauty. Provide the best viewing angle. Open architecture makes it easier to access wires. As a professional tv wall mount factory in china, CNXD provides you with types of Tv wall mounts. CNXD wall mount TV bracket allows you to find the perfect position for all of your av needs.

Heavy-Duty Fixed TV Wall Mount PTS1230 heavy duty flat screen tv wall mounts is specially designed for most 60 '' - 100 '' TVs. The maximum weight is 150kg / 330lbs. It uses high-quality cold-rolled steel to ensure product quality, and the price is favorable! The hanging picture structure ensures fast and simple installation. The open structure provides more air flow and easier access to wires. Reducing the size of the package will allow you to reduce the cost of transportation. Features of PTS1230 Fixed TV Wall Mount Quick and easy installation Includes all necessary wall and display attachment hardware Reduce package size: easier to transport Security Screws: hold TV securely to the wall plate Built in level Specifications of PTS1230 Fixed TV Wall Mount Product Category: Fixed TV Wall Mount Material: steel Surface Finish: Powder Coating Color: Fine Texture Black Dimensions: 1230x625x38mm Fit Screen Size: 60''-100'' Fit Curved TV: no Mounting Hole Pattern: VESA Max. VESA: 1000x600 Weight Capacity: 150kg (330lbs) As a professional tv wall mount design company in china, CNXD provides you with types of Tv wall mounts. CNXD wall mount TV bracket allows you to find the perfect position for all of your av needs.