Offers to Sell

Sodium carbonate, Na2CO3, (also known as washing soda, soda ash and soda crystals) is the inorganic compound with the formula Na2CO3 and its various hydrates. All forms are white, water-soluble salts. All forms have a strongly alkaline taste and give moderately alkaline solutions in water. Historically it was extracted from the ashes of plants growing in sodium- rich soils. Because the ashes of these sodium-rich plants were noticeably different from ashes of wood (once used to produce potash), sodium carbonate became known as "soda ash".[12] It is produced in large quantities from sodium chloride and limestone by the Solvay process. Soda ash is one of the most  important chemical raw materials and is widely used in chemical, glass, metallurgy, paper making, printing & dyeing, synthetic detergent, petrochemical, foodstuff, medicine & sanitation industries, etc. With a large consumption, it occupies a crucial place in national economy. Application: 1.The manufacture of glass is one of the most important uses of sodium carbonate. When it is combined with silica (SiO2) and calcium carbonate (CaCO3) and heated to very high temperatures, then cooled very rapidly, glass is produced. This type of glass is known as soda lime glass.  2. Soda ash also is used to clean the air and soften water.  3. Manufacture of Caustic Soda and dyestuff  4. metallurgy: in the processing of steel and extraction of iron etc.  5. Detergent : It is used as detergent in wool rinsing,medicine and tanning.  6. National defense and some other aspects, such as rock oil refining, paper manufacturing, paint, salt refining, softening of hard water, soap, medicine , food and so on.

Minimum Order: 20 square metres

The Introduction of Petroleum Coke Petroleum coke is a by-product of delayed coking unit when the raw oil is cracked at high temperature to produce light oil.The output of petroleum coke is about 25-30% of the raw oil. Its low calorific value is about 1.5-2 times that of coal, ash content is not more than 0.5%, volatile content is about 11%, and its quality is close to anthracite The Application: 1. Low-sulfur, high-quality cooked coke such as needle coke is mainly used to manufacture ultra-high power graphite electrodes and certain special carbon products; needle coke is an important material for the development of new electric furnace steel making technology in the steel making industry. 2. Medium-sulfur, ordinary cooked coke, used in aluminum smelting in large quantities. 3.High-sulfur, ordinary green coke is used in chemical production, such as the manufacture of calcium carbide, silicon carbide, etc., and also as a fuel for metal casting, etc.

Minimum Order: 20 square metres

The formula of the raw materials of the tofu cat litter is mainly grains such as bean curd residue, pea fiber, corn starch, etc. The raw materials are food grade, rich in protein and carbohydrates, and free of oil. In the production process, the core is the granulator. After a series of special treatment processes, after drying, fermentation and packaging, the tofu cat litter is finally made. advantage 1. The materials are environmentally friendly Tofu cat litter is mainly made of natural tofu residue, which is environmentally friendly and has no harm to eating by mistake. 2. Instantaneous agglomeration Fast water absorption, fast agglomeration, not easy to disperse, not touching the bottom, and more economical dosage. 3. Deodorization and sterilization Clean and deodorize, inhibit bacterial growth, and keep the air in the room fresh and odorless. 4, easy to handle Low dust, light weight, rapid dissolution, no residue, direct flushing toilet, convenient

Minimum Order: 20 square metres

INTRODUCTION: Zircon sand, also known as zircon, is a mineral composed mainly of zirconium silicate (ZrSiO4). Pure zircon sand is a colorless transparent crystal. FORM OF ZIRCON ZIRCON SAND ZIRCON POWDER APPLICATION: To be used in Ceramics. Opacity, whiteness, wear resistance and moisture resistance make it a key component of ceramic tiles, sanitary ware and tableware. To be used in refractory industry to protect the interior of high- temperature furnaces To be used in foundries and precision casting processes for the casting of metals and alloys into various products due to the thermal stability, high melting point and abrasion resistance provided by zircon. Another important application is the production of a broad range of zirconia chemicals, which in turn, have a diverse range of end uses including ceramics, refractory, catalysts, coating electronics and biomedical related products. Some zircon is used as an x-ray filter and as a polishing agent in the production of silicon wafers for the manufacture of semiconductor components such as integrated circuits (computer chips). PHYSICAL INDEX: Refractive index : 1.93 to 2.01 Specific Gravity : 4.6-4.71g/cm3 Bulk density :2.6-2.8g/cm3 Mohs Hardness :7.5 Thermal expansion coefficient: 0.003 cm/cm· ℃ Coefficient of Linear Expansion: 7.2x 10-6 cm/cm℃ Melting point :2100-2300℃ PH: 6.0-8.5

Minimum Order: 20 square metres

Bentonite generally has a hardness of 1-2 (some are relatively hard) and a density of 2-3g/cm3. Also known as porphyry, bentonite or bentonite, it is a non-metallic mineral mainly composed of montmorillonite. It is generally white or light yellow, and due to changes in iron content, it appears light gray, light green, pink, brown red, brick red, gray black, etc. Hardness 1-2, density 2-3 g/cm3. According to the type, content, and layer charge of exchangeable cations in montmorillonite, bentonite can be divided into sodium based bentonite (alkaline soil), calcium based bentonite (alkaline soil), natural bleached clay (acidic soil or acidic white soil), among which calcium based bentonite also includes calcium sodium and calcium magnesium bases.

Minimum Order: 20 square metres

Fluorspar is a common halide mineral, which is a compound composed of calcium fluoride and an important mineral for extracting fluorine. Fluorite has many colors and can also be transparent and colorless. Transparent and colorless fluorite can be used to make special optical lenses. Fluorite has multiple uses in the fiberglass, ceramics, welding rod, and glass industry. Also used in blending with burned lime & dolomite for the steel industry. Calcium fluoride is used a component of electrolyte, fluxing agent for aluminium metallurgy , It is used in glass and fluorescent lamps industry. Fluorite is generally in the form of granules or blocks, with a glassy luster, and is mostly green or purple. Fluorite often emits blue-green fluorescence under ultraviolet or cathode ray irradiation, and its name is derived from this characteristic.

Minimum Order: 20 square metres

ER-QA-01A： 1.Bias repeatability：10μg； 2.Scale factor repeatability : 10ppm； 3. Class II non-linearity repeatability：10μg/g². Application ER-QA , -01A Aerospace Quartz Accelerometer with high precision is used in carrier’s microgravity measuring system, inertial navigation system, static angle measurement system. Features High Precision High Performance

Minimum Order: 1 bags

Today, AAK posted a hydraulic cartridge relief valve E-RV16-26, benchmarking HydraForce RV16-26. It is a screw in, cartridge style, pilot operated (two stage), spool type relief valve, intended for use as a pressure limiting device in demanding hydraulic circuits which require fast response and low hysteresis. Many hydraulic cartridge valve manufacturers in Ningbo China do not have this model. One of our customers in Brazil checked with 8 hydraulic cartridge valve manufacturers in 3 months, but none of them have this cartridge relief valve. He was very happily to get it from AAK finally, and the manufacturing quality and performance is equivalent to HydraForce RV16-26. The selling points of this cartridge relief valve are: 1. Benchmarking HydraForce RV16-26 2. Its service life is 2 times that of its peers Technical parameters of AAK E-RV16-26 HYDRAULIC CARTRIDGE PILOT OPERATED RELIEF VALVE: Max. Operating Pressure: 240 bar (3500 psi) Flow: See PRESSURE DROP VS. FLOW graph Internal Leakage: At port 2 Max. at 85% of crack pressure. 115ml/min. max. Note: Pressure setting below 137.9 bar (2000 psi) 197ml/min. max. Note: Pressure setting above 137.9 bar (2000 psi) Temperature: - 40 to + 120 °C (with Standard Buna N seals) Cavity: VC16-2 For this cartridge style, pilot operated, spool type relief Valve, the quality is benchmarking HydraForce RV16-26, you can also try it out. AAK HYDRAULIC VALVES (639) 2023-07-31 https://www.aakindustry.com/info , -detail/relief-valves-aak639

Kayden, from AH Garner company in the UK, has successfully purchased hydraulic valve blocks in Ningbo in recent years, and has cooperated with AAK on some high requirements hydraulic valve blocks for many years. He sent an email at the end of last year: I need AAK’s help. After communication, we learned that a new hydraulic equipment of their company was complained by customers about oil leakage in about 3 months. After inspection, their after-sales personnel found that when the equipment is switched with high-speed and high-frequency action under high pressure, the small O-ring of the cover plate of the hydraulic valve block is prone to oil leakage. The engineer asked Kayden to find the original supplier to replace the hydraulic valve blocks or cartridge valves. Unfortunately, Kayden purchased the hydraulic valve blocks and threaded cartridge valves from two factories. The manufacturer of the hydraulic valve blocks replied that the thread size accuracy of the cartridge valves did not meet the standard and caused oil leakage, while the cartridge valve manufacturer said that the accuracy of the hydraulic valve blocks did not meet the standard. The hydraulic valve blocks and cartridge valves have passed the inspection. How can there be a problem as soon as they are assembled on the equipment? Kayden suspected that the design of the hydraulic valve block was flawed, but the engineer thought the design drawing was in line with the principle. The customer didn't receive the solution, and complained to the boss, who asked Kayden to completely solve the oil leakage problem of the hydraulic valve blocks within 30 days. Now Kayden was stumped and didn't have a clue. I asked Kayden to send us the drawings of the hydraulic valve block and cartridge valve, and system principles. AAK engineers found no problems after analysis. Our engineer asked Kayden to provide the video after the equipment was started up. Combined with the system schematic diagram and equipment fault video, our engineer judged that the position of installing O-ring at the interface of hydraulic valve block and cartridge valve was inappropriate. If the position of the O-ring is lowered, and the cover plate O-ring is completely free of oil, install and fasten the cartridge valve cover plate, and produce the hydraulic valve block and cartridge valve in a same factory, the oil leakage problem of the hydraulic valve block may be solved completely. Kayden seems to have seen the dawn and asked AAK to make samples. After 25 days, AAK sent out the integrated hydraulic valve block sample. A few days ago, Kayden emailed us that it has been 3 months since the hydraulic valve block was replaced with AAK samples, the equipment works normally without oil leakage. Kayden told me that AH Garner engineer admired AAK’s strictness in details. It is so obvious, why didn't he find such an obvious problem? In order to make sure that the integrated hydraulic valve block is 100% free of oil leakage, it is not only necessary to be strict on the position of the O- ring, but also the installation of the O-ring on the hydraulic valve block. On the premise of ensuring the reasonable compression of the O-ring, it is necessary to avoid oil in the annular sealing surface of the O-ring, and any displacement of the O-ring will be in an oil-free lubrication state, so as to improve the displacement resistance. Kayden privately told us that the boss praised his quick and thorough solution to the problem, and asked him to purchase integrated hydraulic valve blocks from AAK in the future. AAK hydraulic valve blocks, be strict in every detail, you are welcome to have a small try. https://www.aakindustry.com/info-detail/hy , draulic-valve-blocks-aak209

Antonio, from Mexico, began purchasing hydraulic cartridge valves from China 3 years ago. Last September, Antonio customized a hydraulic pilot operated pressure relieving valve in Ningbo for use in their newly developed hydraulic power unit. During equipment commissioning, it was found that the internal leakage of the hydraulic pilot operated pressure relieving valve was not up to standard and the opening and closing performance was not satisfactory. The original hydraulic pressure relieving valve manufacturer has revised the samples 3 times, but none of them can satisfy their engineers. Antonio was very upset. Antonio saw the customer case of the hydraulic pressure relieving valve released by AAK in B2B, and left a message. 1.What is the minimum internal leakage of AAK hydraulic pilot operated pressure relieving valve? 2.What is the sealing effect of AAK hydraulic pilot operated pressure relieving valve? 3.What is the opening and closing performance of AAK hydraulic pilot operated pressure relieving valve? I suspected that he was unsuccessful in testing hydraulic pressure relieving valve from other hydraulic cartridge valve manufacturer. After communication, it was learned that the original manufacturer had failed 3 times, which touched me. Perhaps the direction of optimization was wrong. According to the equipment abnormality video sent by him, combined with the hydraulic system and the original sample, AAK engineers found the problem and were 90% confident that the sample would be successful. After 45 days, AAK sent 8 samples of hydraulic pilot operated pressure relieving valves. Last week, Antonio said that after installing AAK hydraulic pilot operated pressure relieving valve into their hydraulic unit, the operational lag was resolved. AAK hydraulic pilot operated pressure relieving valve has two major advantages: small internal leakage, good opening and closing characteristics, and the original hydraulic cartridge valve manufacturer can only be amazed. 1. The valve sleeve of the hydraulic pressure relieving valve has an outwardly inverted triangular clamp head at one end, and the adjusting sleeve catches the clamp head. The valve sleeve and the adjusting sleeve are fixedly connected together. There is a steel ball between the valve seat and the pilot valve spool, and there is a circular hole on the valve seat that communicates with the radial hole and can accommodate the steel ball. There is a blind hole on the pilot valve spool to accommodate the steel ball. 2. The valve sleeve has an axial two-stage step through hole that communicates with the oil outlet chamber as an overflow and outflow port. The junction between the large hole and the small hole is a conical surface, the valve spool and the valve sleeve are sealed at the conical surface, and the oil outlet chamber is located near the conical surface at the bottom of the large hole of the valve sleeve. The control oil chamber is located at the rear of the valve sleeve large hole, and the valve sleeve has a three-level outer circle outside. The right end face of the valve sleeve is an inner cone, which forms an annular plane between the inner cone and the outer cone, making the contact area between the valve sleeve and the valve seat small and stable, structurally reducing internal leakage rather than simply "blocking" internal leakage as the original hydraulic cartridge valve manufacturer did. 3. There are two stages of holes inside the valve spool, with small holes for damping and large holes for placing springs. There are two narrow grooves in the middle of the valve spool and a wide groove at the right end, which can reduce the contact between the valve spool and the valve sleeve and cause sliding friction, greatly improving the opening and closing characteristics of the valve. AAK hydraulic pilot operated relieving valve has two advantages: small internal leakage and good opening and closing characteristics. You can also try it out. AAK HYDRAULIC CARTRIDGE VALVES (547) 2023-03-31 https://www.aakindustry.com/info , -detail/pressure-relieving-valves-aak547

Chinese hydraulic valve manufacturers, the number of exports in the past 2 years is slowly increasing, which also seems to indicate that the quality of Chinese hydraulic valves has been recognized. Ten years ago, almost all Chinese hydraulic valves were supplied to domestic equipment manufacturers, and AAK began to provide samples for HydraForce. AAK hydraulic valves have indeed made a lot of progress in manufacturing / R & D in recent years, especially the export of high-pressure hydraulic valves. According to the data of Ningbo customs, AAK hydraulic valves account for more than 68%. The rapid growth of AAK hydraulic valves is due to the strict ODM, operation specification and quality control process for these big brands, which is more strict than the ISO certification system. When we communicate with any hydraulic valve customer, we don't care much about the specific PO amount of a hydraulic valve, but focus on the cooperation opportunities with him, the supply relationship of common destiny, especially the market prospect. AAK hydraulic valves have surpassed many peers in the market and research and development in recent years, but in the part of the market, especially in the mature developed market, there is a weakness in the market experience. Using AAK hydraulic valves manufacturing and R & D capabilities, combining with customers' industry experience and business creativity to jointly build a hydraulic valve supply chain system is our direction. It must be admitted that the way of thinking of European and American people in many commercial parts is worthy of our reference and learning. Therefore, AAK hydraulic valves expect to establish a business relationship of the community of common destiny with real hydraulic valve customers. Today, the new generation of hydraulic valve practitioners in Europe and the United States has been separated from manufacturing for decades. Their difficulty is how to find a healthy, sustainable, guaranteed and common fate hydraulic valve supply chain and effectively realize the actual commercial delivery. Perhaps, China's small and medium-sized hydraulic valve enterprises and European and American small and medium-sized hydraulic valve enterprises will find a better combination of interests, and then jointly create new users, which may be a new trend of globalization in the future. COVID-19 is impeding the development of globalization, but the globalization of hydraulic valves can not stop itself. The globalization of Chinese hydraulic valve manufacturers will not only stay at the level of hydraulic valve manufacturing and export. AAK is more concerned about how to make effective use of the favorable position of AAK hydraulic valve manufacturing and R & D, and then combine the business experience of the local market of developed countries to resort out and shape the innovative hydraulic valve business model, such as the software service module or platform of a hydraulic valve supply chain system. If AAK uses our hydraulic valve manufacturing and R & D capabilities and customers use their own industry experience and business creativity, such a combination must be 1 + 1 greater than 2. Know + do = get. 99% of people didn't get it in the end because they didn't do it at all. Why not AAK hydraulic valves to do it? Here we are coming....... AAK hydraulic valves, just change for you, with temperature from AAK hydraulic valves https://www.aakindustry.com/info , -detail/hydraulic-valves-aak208

Karl is from Sweden. He purchases the standard parts of hydraulic cartridge valves from Italy, and the customized parts of hydraulic cartridge valves from Ningbo. Some time ago, when they developed hydraulic drilling equipment, they needed to customize the hydraulic cartridge needle valve. He made samples in a hydraulic cartridge valve manufacturer in Ningbo. Due to the unstable pressure control of the hydraulic cartridge needle valve, the selling point of the new hydraulic drilling cannot be realized. The Italian hydraulic cartridge valve manufacturer has no time to customize. The engineer pushed, and Karl was very anxious. This Ningbo manufacturer contacted me and hoped that AAK would develop this hydraulic cartridge needle valve. I said: I have no interest to develop for my peers. If you are really in a hurry, let the customer contact AAK directly. The next day, I received an email from Karl. According to the schematic diagram of the hydraulic system provided by him and the anatomical sample of the original hydraulic cartridge needle valve, as long as the pressure balance within the valve is solved and the most suitable flow area is found, this hydraulic cartridge needle valve can achieve fine pressure control. After 60 days, AAK sent 10 samples of hydraulic cartridge needle valves. Yesterday, Karl emailed us to inform that the equipment was smoothly debugged. Their engineers admired AAK's idea for the precise pressure control of the hydraulic cartridge needle valve. AAK hydraulic cartridge needle valve has an appropriate flow area between the valve spool and the valve seat, which reduces the back pressure when the hydraulic cartridge needle valve has a large displacement, and the through-hole of the valve spool achieves pressure balance up and down the valve spool. 1. The lower part of the valve rod of the hydraulic cartridge needle valve is connected to the valve spool, and the upper part of the valve body has an axially machined orifice in which an anti rotation cylinder can be inserted. A circumferential lock is formed between the anti rotation cylinder and the valve body. 2. The spool of the hydraulic cartridge needle valve is inserted into the anti rotation cylinder and forms a circumferential lock between the cartridge and the anti rotation cylinder, with an axial sealing and sliding fit. There are oil inlet and outlet channels on the side and lower axial directions of the valve body, respectively. At the same time, a through-hole is provided on the valve spool to achieve pressure balance up and down the valve spool. 3. The valve seat is installed in the oil outlet passage and forms an axial insertion fit with the upper valve spool. The upper part of the valve spool is cylindrical, and the lower end is symmetrically provided with two V-shaped throttle ramps. When the valve spool is closed, the valve spool chamfer surface contacts the valve seat chamfer surface, which can achieve fluid cutoff. AAK hydraulic cartridge needle valve, fine pressure control, few cartridge valve manufacturer can handle it, you can also give it a try! https://www.aakindustry.com/info-detail/ne , edle-valves-aak546

In mid November, Steven from Canada left a message on the website of hydraulic cartridge valve manufacturer AAK: Can you produce hydraulic cartridge pressure control valve with 2μm precision spool? From the name Steven alone, I feel that he is not an ordinary purchaser. Most of the Steven I know are leaders. After communication, it was learned that he is the procurement manager of the company. Their colleagues have customized hydraulic pressure control valves from other hydraulic cartridge valve manufacturers in China, but the accuracy of the valve spool does not meet the standard, which has caused some delay and their engineering department is in a passive situation. Now, the procurement department is under a lot of pressure. Steven's hydraulic pressure control valve is failed in not meeting the valve spool accuracy of 2μm. As long as Steven understands how hydraulic cartridge valve manufacturer AAK produces valve spool and how to control accuracy, he will have a preliminary trust in hydraulic cartridge valve manufacturer AAK. Once he receives the hydraulic pressure control valve sample sent by AAK and the sample is recognized, Steven's trust in the hydraulic cartridge valve manufacturer AAK will be established. The production of hydraulic pressure control valve spool involves the material selection first, then rough machining, and how to achieve precision machining successfully. Precision machining requires experienced technicians and equipment with stable accuracy. For precision 2μm valve spool, AAK uses Japanese STAR CNC precision automatic lathe. Before processing, our production engineer sets the processing program for the technician, and then a professional tool setter is responsible for tool alignment. After precise positioning, the technician can proceed with the machining. That is, a process, AAK subdivides it into 3 positions, with dedicated personnel for each position, while most hydraulic cartridge valve manufacturers have 1 person for 3 positions. The STAR CNC precision automatic lathe is equipped with 24 cutting tools and adopts a dual axis layout. With one clamping, it can be processed in one go, which not only improves production efficiency but also avoids human error. The online detection function of the equipment is highly favored by technicians. During the processing, key data can be detected online in a timely manner, and the program automatically compares, providing assurance for stable accuracy. Today, we sent out 12 hydraulic cartridge pressure control valve samples, and I believe there is an additional Steven on AAK's customer list. AAK hydraulic cartridge pressure control valve, 2μm accuracy valve spool, you can also give it a try! AAK HYDRAULIC CARTRIDGE VALVES (755) 2024-01-09 https://www.aakindustry.com/info , -detail/pressure-control-valves-aak755

Der rechtliche Status von Pentobarbital/Nembutal ist in Deutschland derzeit eingeschränkt. Im März 2017 entschied das Bundesverwaltungsgericht, dass das verfassungsrechtlich geschützte Recht auf Selbstbestimmung nicht das Recht einschließt, tödliche Drogen für den Suizid zu beschaffen und zu verwenden. Im Januar 2021 schlugen Abgeordnete des Deutschen Bundestages jedoch einen Gesetzesvorschlag vor, der unheilbar kranken Erwachsenen die Sterbehilfe ermöglichen soll, sobald sie über die Art und die Folgen ihrer Entscheidung umfassend aufgeklärt wurden. Während der rechtliche Status von Pentobarbital Nembutal in Deutschland weiterhin eingeschränkt ist, kann es daher einige Ausnahmen für todkranke Personen geben, die ihrem Leben ein Ende setzen möchten. Für diejenigen, die Pentobarbital/Nembutal in Deutschland kaufen möchten, sind Online-Quellen möglicherweise die am besten zugängliche Option. Beim Online-Kauf von Pentobarbital/Nembutal ist jedoch Vorsicht geboten. Einige Online-Quellen sind möglicherweise betrügerisch und verkaufen möglicherweise gefälschte oder gefährliche Medikamente, die schädlich sein könnten. Daher ist es wichtig, vor dem Kauf gründlich zu recherchieren und sicherzustellen, dass das Produkt von guter und standardmäßiger Qualität ist und nur bei seriösen Verkäufern wie uns einzukaufen.shumerkoch@gmail.com Beim Online-Kauf von Nembutal ist es wichtig, bestimmte Vorsichtsmaßnahmen zu treffen, um die Sicherheit zu gewährleisten. Es ist beispielsweise ratsam, eine sichere Zahlungsmethode zu verwenden und nur bei Quellen einzukaufen, die eine diskrete Verpackung und einen diskreten Versand anbieten. Darüber hinaus ist es wichtig, sich der möglichen Nebenwirkungen und Risiken bewusst zu sein, die mit der Verwendung von Pentobarbital/Nembutal verbunden sind, wenn man nicht über die richtige Einnahme informiert wird. Daher ist es wichtig, unsere Anweisungen zur Verwendung von Pentobarbital sorgfältig zu befolgen, um die erwarteten Ergebnisse zu erzielen. Jede Dosierung hängt von der Person ab und um Ihre tödliche Dosierung zu ermitteln, müssen wir Ihr Alter, Ihre Größe und Ihr Gewicht kennen. Bewusstsein Ich bin 25 Jahre oder älter und bestätige, dass ich voll und ganz dabei bin bewusst, dass die auf dieser Website verkauften Produkte gelten als sehr tödlich. Bei Fragen zum diskreten Kauf von Natriumpentobarbital senden Sie eine E-Mail an shumerkoch@gmail.com Pentobarbital natrium Frankfurt kaufen, Pentobarbital Niederlande kaufen, Pentobarbital Finnland kaufen, Pentobarbital flüssig Europa kaufen, Nembutal Sodium Hamburg kaufen, Pentobarbital Sodium in Japan kaufen, Nembutal in Estland kaufen, Pentobarbital Nembutal in Finnland kaufen, https://658db43365500.site123.me/ https://forum.aggiustatutto.it/elettrodo , mestici-e-apparecchi- elettrici/395024-natrium- , pentobarbital-legal-kaufen-schweiz- pentobabs-d , uck-com.html https://www.doktor.rs/foru , m/dermatologija/pentobarbital-kaufen-ohne- reze , pt-nembutal-kaufen-deutschland-t440839.html

Minimum Order: 5 dozens