Telecom Equipment & Accessories

Mini type 1xN 2xN PLC splitter with connectors TELCORDIA 1209&1201 STANDARD Dawnergy’s planar light wave circuit (PLC) splitter is optical power management device which uses silica optical waveguide technology. It has small size, high reliability, wide operating wavelength range. It is widely used in PON networks and realizes optical signal power splitting. Features: Low insertion loss Low PDL Good channel uniformity High-reliability and stability Qualified according to Telcordia 1209 and 1221 requirements Parameters 1x2 1x4 1x8 1x16 1x32 1x64 Operating Wavelength(nm) 1260~1650 Insertion Loss (dB) Typical 3.6 6.8 10 13.1 16.2 20 Max(P/S) 3.8/4.0 7.2/7.4 10.5/10.7 13.6/13.7 16.5/16.8 20.5/21.0 Uniformity (dB) Typical 0.3 0.4 0.5 0.6 0.8 1.2 Max 0.4 0.6 0.8 1.2 1.5 2.5 PDL (dB) Typical 0.1 0.1 0.15 0.15 0.15 0.2 Max 0.2 0.2 0.3 0.3 0.3 0.4 Return Loss (dB) Min 55 Directivity (dB) Min 55 Fiber Length (m) 1 (+/-0.05) or customer specified Fiber Type ITU-T G657A1 or customer specified WDL (dB) Typical 0.2 0.2 0.2 0.3 0.3 0.3 Max 0.3 0.3 0.3 0.5 0.5 0.5 TDL (dB) (-40~85℃) Typical 0.2 0.2 0.2 0.3 0.3 0.3 Max 0.4 0.4 0.4 0.5 0.5 0.5 Operating Temperature (℃) -40~85 Storage Temperature (℃) -40~85 Packaging Size(mm) Bare Splitter 40x4x4 50x7x4 60x12x4 Mini Module 60x7x4 60x12x4 80x20x6 100x40x6 Cassette Type 100x80x10 120x80x18 　 Parameters 2x2 2x4 2x8 2x16 2x32 2x64 Operating Wavelength(nm) 1260~1650 Insertion Loss (dB) Typical 3.7 7 10.8 13.6 16.8 20.5 Max(P/S) 3.9/4.2 7.5/7.8 11.2/11.5 14.2/14.5 17.4/17.7 21.0/21.5 Uniformity (dB) Typical 0.5 1 1 1.2 1.5 2.2 Max 0.6 1.2 1.5 1.8 2 2.7 PDL (dB) Typical 0.1 0.1 0.2 0.3 0.3 0.3 Max 0.2 0.2 0.4 0.4 0.4 0.4 Return Loss (dB) Min 55 Directivity (dB) Min 55 Fiber Length (m) 1 +/-0.05 or customer specified Fiber Type ITU-T G657A1 or customer specified WDL (dB) Typical 0.3 0.3 0.3 0.5 0.5 0.8 Max 0.4 0.4 0.5 0.6 0.8 1.2 TDL (dB) (-40~85℃) Typical 0.3 0.3 0.3 0.4 0.4 0.4 Max 0.4 0.4 0.4 0.5 0.5 0.5 Operating Temperature (℃) -40~85 Storage Temperature (℃) -40~85 Packaging Size(mm) Mini Module 60x7x4 80x12x5 100x20x6 100x40x6 Notes: 1. Measurements are done at room temperature. Connector loss is excluded in the above specifications. 2. S=Standard grade, P=Premium grade

FTTH FAT 2 Ports Fiber Terminal Termination Box Wall Outlet SC Flame retardant White ABS This fiber access terminal is 2cores, ftth mini wall outlet, it mainly used wall mounted or desktop in ftth network, The interface is SC adapters, UPC or APC is ok, it is good choice for CATV, CCTV or GPON networks too. Features With protection doors dustproof, IP30 dustproof,indoor use Suitable for many types of modules, used in cabling network area subsystem Embedded type surface, easy for installation and removal SC simplex or LC duplex coupler surface mounted installation and concealed panel installation All modules are solderless mode Technical specification Item Parameters Cable used 2.0*3.0mm drop cable or indoor cable Fiber cladding diameter 125um (G652 or G657) Fiber diameter 250um or 900um Fiber mode Single mode and multimode Tensile strength >50N Operating temperature -40~+85°C Adapter SC&LC Insertion loss ≤0.2dB (1310&1550nm) Fiber count 2cores

IoT RTU, IoT Gateway, Industrial celluar router, Ethernet I/O module, LoRa gateway etc.

Minimum Order: 1 bags

Product Description Underground 48 Core Outdoor Fiber Optic Cable GYTS Optical Cable Outdoor Duct Underground Direct Buried Armoured Fiber Optic Cable 12 24 48 96core GYTS optical cable generally refers to layer twisted optical cable. The layer twisted optical cable is composed of a plurality of casings containing optical fibers twisted into a round cable core around the central reinforcing member. The metal or non-metallic reinforcement is located in the center of the optical cable, and the loose tube containing the optical fiber is arranged around the reinforcement. Features 1. Adopt "SZ" bidirectional layer twisting technology 2. Filling water-blocking ointment step by step, full-section water-blocking 3. The steel (aluminum) belt has reliable bonding with the edge, high strength, and no cracking when twisted 4. Stable fiber excess length control 5. After the cable is formed, the additional attenuation of the optical fiber is almost zero, and the dispersion value does not change 6. Excellent environmental performance, applicable temperature range is -10℃~+70℃ 7, suitable for overhead, pipeline, direct buried and other laying methods Application These corrugated steel tape armored cables are suitable for installation in aerial or duct environment for long haul communication, LAN Product Name GYTS fiber optic cable Fiber Count 12-144 Fibers Construction Stranded Loose Tube Fiber Type Singlemode G.652D Outer Jacket Material PE(Black) Weight 100kg/km Arm , or Layer Aluminum Tape Application Aerial and Duct Jacket Diameter 9.8mm-16.1mm Jacket Material PE Cable Length 1KM-5KM per drum Test Wavelength 1310/1550nm Operation Temperature -20℃ to +60℃ Product Details 11.jpg22.jpg66.jpg FAQ -1.jpg Q1:What are the advantages of your price? A1: We have our own factory, professioanl machinery equipment . We can meet the price advantage of products with the same quality parameters, and we promise to achieve a price of 1%-10% lower than that of our peers. Q2: What is your quality advantage? A2: We strictly according to the ISO9001 quality management system, insisting "Enough Cores, Enough Meters, High Quality, High Performance". Providing our customers with higher quality products and services. Q3. Do you support customized brands? A3: Yes! The professional OEM services will be welcomed to us. Our factory accepts to make the logo free for bulk orders. Q4: What are the benefits of working with you? A4: New customers can enjoy AIXTON’s stock and annual year-end dividends, and support long-term cooperative customers to upgrade to global agents and enjoy more discounted prices. glasfaserkabel

30 Meter Monopole Painting Coating Wifi Tower Monopole Tower What Is Monopole Tower? Monopole Tower belongs to the technical field of pipe towers, and includes a working platform connected with the tower body and the upper part of the tower body. The bottom wall of the tower body is provided with a lower door hole, and the wall of the work platform is provided with a door opening, and the antenna bracket is fixed on the fence of the working platform, and the structure of the tower body is set by the main pole of the ladder and the main pole of the ladder. A ladder formed by a crosspiece, the main pole of the ladder is fixedly connected with the support frame, and the support bracket is screwed with the connecting bracket disposed on the inner wall of the tower. The advantages of the Monopole Tower are: the structure is simple and reasonable; the appearance is beautiful; the installation and use are convenient. And compared to the angle steel tower, the footprint is smaller. Highlights of JIAYAO self-suppo , rting tower ● Leading design concept. ● Versatility, modular design, flexible configuration of accessories. ● Tower group design, modification and adjustment. ● The tower section is universal, and the same tower section taken from the same mother tower is completely common in different tower types. ● Lower costs. ● Self-supporting tower light weight. ● Self-supporting tower installation cost is good. ● Self-supporting tower installation time is short. ● High reliability. ● The design and processing of JIAYAO's self-supporting tower products are in line with ISO 9001:2000 quality management system. ● 50 years design life.

Wholesaler Types Of Communication Towers Features: 1. The seamless steel pipe is used as the column material, the wind load coefficient is small, and the wind resistance is strong. 2. The tower column is connected by an outer flange, and the bolt is pulled, which is not easy to damage and reduces maintenance costs. 3. The tower is arranged in a triangular shape to save steel. 4. The roots are small, the floor space is small, the land resources are saved, and the site selection is convenient. 5. The tower body is light in weight, and the new three-leaf cutting board foundation reduces the basic cost. 6. Truss structure design, convenient transportation and installation, and short construction period. 7. The tower type is designed with the wind load curve changing, and the lines are smooth. It is not easy to collapse in case of rare wind disasters, reducing human and livestock casualties. 8. The design conforms to the national steel structure design specification and tower design rules, and the structure is safe and reliable. Highlights of JIAYAO self-supp , orting tower ● Leading design concept. ● Versatility, modular design, flexible configuration of accessories. ● Tower group design, modification and adjustment. ● The tower section is universal, and the same tower section taken from the same mother tower is completely common in different tower types. ● Lower costs. ● Self-supporting tower light weight. ● Self-supporting tower installation cost is good. ● Self-supporting tower installation time is short. ● High reliability. ● The design and processing of JIAYAO's self-supporting tower products are in line with ISO 9001:2000 quality management system. ● 50 years design life. What Is The Details of JIAYAO 3 Legged Tubular Steel Tower? Design standard TIA/EIA-222-G/F Welding standard AWS D1.1 Galvanization standard ASTM A123 Design Wind Speed Up to 200 km/h Angular steel Material quality Mild Steel:Q235B/ASTM A36/S235JR High Steel:Q345B/ASTM A572/S355JR Allowable  , deflection 0.5 ~1.0 degree Bolt grade Gr 4.8, Gr 6.8, Gr 8.8 Marking Hydraulic Press Stamping What is the height of JIAYAO 3 Legged Tubular Steel Tower we can provide? 5m up to 50m is the tower height we can provide. What antenna can be mounted on JIAYAO 3 Legged Tubular Steel Tower? Type of antenna Description Panel antenna (sector antenna) GSM antenna for 5G:2.52m×0.265m×0.13m, 1.31m×0.32m×0.11m Parabolic reflector(dish antenna) Microwave antenna Diameter:0.6m, 0.9, 1.2m, 1.6m, 1.8m, 2.4m RRU Radio Remote Unit:0.45m×0.32m×0.25m WIFI antenna Grid or parabolic directional antenna / yagi / omnidirectional antennas Other Antenna VHF/UHF Dual-band Antenna FM antenna

Galvanized Microwave Antenna And Communication Self Supporting Tower 4 Legged Angular Steel Tower What Is 4 Legged Angular Steel Tower? 4 legged angular steel tower is a kind of self-supporting communication tower，It can also be called 4 legged angular steel communication tower, telecommunication tower, antenna tower. 4 legged angular steel tower are higher steel structures used all over the world for communication applications. Their function to support antennas for telecommunications, broadcasting and WIFI internet. 4 legged angular steel tower is usually come with pre-designed accessories, just like platforms, ladders with cable tray, antenna brackets, aviation light brackets and fall prevention device, etc. 4 legged angular steel tower are based on either ground or building, and they are commonly designed in trusses structure to carry the wind loads and seismic loads. 4 legged angular steel tower is easy to process, transport and install. The overall rigidity of the angle steel tower is large, the bearing capacity is strong, and the technical application is mature. Highlights of JIAYAO self-suppor , ting tower ● Leading design concept. ● Versatility, modular design, flexible configuration of accessories. ● Tower group design, modification and adjustment. ● The tower section is universal, and the same tower section taken from the same mother tower is completely common in different tower types. ● Lower costs. ● Self-supporting tower light weight. ● Self-supporting tower installation cost is good. ● Self-supporting tower installation time is short. ● High reliability. ● The design and processing of JIAYAO's self-supporting tower products are in line with ISO 9001:2000 quality management system. ● 50 years design life.   What Is The Details of JIAYAO 4 Legged Angular Steel Tower? Design standard TIA/EIA-222-G/F Welding standard AWS D1.1 Galvanization standard ASTM A123 Design Wind Speed Up to 200 km/h Angular steel Material quality Mild Steel:Q235B/ASTM A36/S235JR High Steel:Q345B/ASTM A572/S355JR Allowable  , deflection 0.5 ~1.0 degree Bolt grade Gr 4.8, Gr 6.8, Gr 8.8 Marking Hydraulic Press Stamping What is the height of JIAYAO 4 Legged Angular Steel Tower we can provide? 50m up to 120m is the tower height we can provide. What antenna can be mounted on JIAYAO 4 Legged Angular Steel Tower? Type of antenna Description Panel antenna (sector antenna) GSM antenna for 5G:2.52m×0.265m×0.13m, 1.31m×0.32m×0.11m Parabolic reflector(dish antenna) Microwave antenna Diameter:0.6m, 0.9, 1.2m, 1.6m, 1.8m, 2.4m RRU Radio Remote Unit:0.45m×0.32m×0.25m WIFI antenna Grid or parabolic directional antenna / yagi / omnidirectional antennas Other Antenna VHF/UHF Dual-band Antenna FM antenna

Hot Dip Galvanized Mobile Phone Signal Bts Telecommunication Tower Product Description Our company is a professional steel tower manufacturer with ISO certificates based in China. Supported by the team of professional engineers,technicians,skill workers,we are dedicated to providing our global customers with high quality telecom towers. The detailed information is specified in the following table.We sincerely look forward to cooperating with you.  1.key Details: Place of Origin: Hebei, China (Mainland) ; Brand Name: Jaoyao or OEM ; Model Number: Telecom Tower. Surface treatment: Hot Dip Galvanizied or painted. 2.Packaging & Delivery: Packaging Details: Telecom tower will be bundled by Galvanized strapping as per client's requirements. Deliver:Shipped in 20 days after payment from Tianjin port. Tower members: One steel tower is separated into several bundles. Bolts: Packing material is robust nylon bag or steel drum. We are telecom tower manufacturer. 3. Technical Data Design 1. Design Code TIA/EIA-222-G/F Structure Steel 2. Grade Mild Steel High Tensile Steel GB/T 700:Q235B, Q235C,Q235D GB/T1591:Q345B, Q345C,Q3455D ASTM A36 ASTM A572 Gr50 EN10025: S235JR, S235J0,S235J2 EN10025: S355JR, S355J0,S355J2 3. Design ,  Wind Speed Up to 250 km/h 4. Allowable deflection 0.5 ~1.0 degree @ operational speed 5. Te , nsion strength (Mpa) 360~510 470~630 6. Yield strength (t≤16mm) (Mpa) 355 235 7. Elongation (%) 20 24 8. Impact strength KV (J) 27(20°C)---Q235B(S235JR) 27(20°C)--- Q345B(S355JR) 27(0°C)---Q235C(S235J0) 27(0°C)---Q345C(S355J0) 27(-20°C)---Q235D(S235J2) 27(-20°C)---Q345D(S355J2) Bolts & Nuts 9. ,  Grade Grade 4.8, 6.8, 8.8 10. Standards for mec , hanical properties 10.1 Bolts ISO 898-1 10.2 Nuts ISO 898-2 10.3 Washers ISO 6507-1 11. Standards for Dimensions , 11.1 Bolts DIN7990, DIN931, DIN933 11.2 Nuts ISO4032, ISO4034 11.3 Washers DIN7989, DIN127B, ISO7091 Welding 12. Met , hod CO2 Shielded Arc Welding & Submerged Arc We , lding(SAW) 13. Standard AWS D1.1 Marking 14. Method of marking  , of the members Hydraulic Press Stamping Galvanizing 15.  , Galvanization standard of steel sections ISO 1461 or ASTM A123 16. Galvanizatio , n standard of bolts and nuts ISO 1461 or ASTM A153 Test 17. Fact , ory test Tensile test,Elements analysis, Sharpy tes , t(impact test), Cold Bending,   Preece te , st,Hammer test Capacity 18. Maximum Production Capacity ,   50,000 TON per annum

Wifi Radio Antenna Mast Steel Tower 3 Legged Angular Steel Tower What Is 3 Legged Angular Steel Tower? 3 legged angular steel tower is a kind of self-supporting communication tower，It can also be called 3 legged angular steel communication tower, telecommunication tower, antenna tower. 3 legged angular steel tower are higher steel structures used all over the world for communication applications. Their function to support antennas for telecommunications, broadcasting and WIFI internet. 3 legged angular steel tower is usually come with pre-designed accessories, just like platforms, ladders with cable tray, antenna brackets, aviation light brackets and fall prevention device, etc. 3 legged angular steel tower are based on either ground or building, and they are commonly designed in trusses structure to carry the wind loads and seismic loads. 3 legged angular steel tower need less ground area and suit to construct in many situations. Highlights of JIAYAO self-su , pporting tower ● Leading design concept. ● Versatility, modular design, flexible configuration of accessories. ● Tower group design, modification and adjustment. ● The tower section is universal, and the same tower section taken from the same mother tower is completely common in different tower types. ● Lower costs. ● Self-supporting tower light weight. ● Self-supporting tower installation cost is good. ● Self-supporting tower installation time is short. ● High reliability. ● The design and processing of JIAYAO's self-supporting tower products are in line with ISO 9001:2000 quality management system. ● 50 years design life.   What Is The Details of JIAYAO 3 Legged Angular Steel Tower? Design standard TIA/EIA-222-G/F Welding standard AWS D1.1 Galvanization standard ASTM A123 Design Wind Speed Up to 200 km/h Angular steel Material quality Mild Steel:Q235B/ASTM A36/S235JR High Steel:Q345B/ASTM A572/S355JR Allowable  , deflection 0.5 ~1.0 degree Bolt grade Gr 4.8, Gr 6.8, Gr 8.8 Marking Hydraulic Press Stamping What is the height of JIAYAO 3 Legged Angular Steel Tower we can provide? 10m up to 50m is the tower height we can provide. What antenna can be mounted on JIAYAO 3 Legged Angular Steel Tower? Type of antenna Description Panel antenna (sector antenna) GSM antenna for 5G:2.52m×0.265m×0.13m, 1.31m×0.32m×0.11m Parabolic reflector(dish antenna) Microwave antenna Diameter:0.6m, 0.9, 1.2m, 1.6m, 1.8m, 2.4m RRU Radio Remote Unit:0.45m×0.32m×0.25m WIFI antenna Grid or parabolic directional antenna / yagi / omnidirectional antennas Other Antenna VHF/UHF Dual-band Antenna FM antenna

As a fiber optic products supplier in the industry, TUOLIMA focuses on brand customization, multi-selective product logo printing, high-end and independent packaging design, to provide customers with a one-stop service that is quite trusted by professionals worldwide. GJS-901 is vertical/Dome type Splice Closure, and its installation is quite simple. This dome fiber optic splice closure can be placed in aerial, underground, wall-mounting, hand hole mounting and duct-mounting applications. The strong housing and main components of the splice closure dome provide fire resistant, waterproof and quakeproof while protecting splices during pulling and impacting. The dome closure fiber optic closure ensures long term reliability and usage under ambient temperature from -40℃ to +65℃. As one of the professional fiber optic accessories suppliers, TUOLIMA can customize the optical cable according to your requirements. Details of TGJS-901 Dome Type Fiber Optic Splice Closure Reinforce rebar on the body of closure make excellent performance under impact, pulling, tension etc Convenient to increase or reduce trays/ cassette for capacity requirement Spacious storing tray/ cassette for storing and maintenance 3 fixing item/designs to prevent fiber optic cable from external effect Can be used from- 40 ℃ to +65℃ temperature range Easy to re-enter without tools Integrated seal, air tight and water proof, flame-retarded Exquisite small Dimension design, convenience installation application Specification of TGJS-901 Dome Type Fiber Optic Splice Closure Model No. TGJS-901 Color Black Capacity 48 cores Protection Level IP68 Material PP+GF Inlet/outlet 1+3 Dimension(MM) 300*Ф120 Sealing Method For Inlets Heat shrinkable Packing And Comments Of TGJS-901 Dome Type Fiber Optic Splice Closure Package dimensions(W*H*D) 8pcs/15.21kgs/680mm*400mm*210mm Package material Standard carton for sea shipping or air express

As a fiber optic products supplier in the industry, TUOLIMA focuses on brand customization, multi-selective product logo printing, high-end and independent packaging design, to provide customers with a one-stop service that is quite trusted by professionals worldwide. The body of this closure splitter box is made of fiberglass and PP as customer's request that has extremly high tensile strength, waterproof and dustproof protection function, reaching IP68. This joint closure optic splitter box can be equipped with 1*16 Mini splitter& 1*16 card type splitter and 16 SC adapters. It can be mounted wall, aerial or holding-pole with one or two pieces of metal board tightly attached onto the cable or pole. Details of TGJS-303A Splitter Type Fiber Optic Splice Closure Inside Splitter place look: Could install a 1x16 mini splitter or a 1x16 card type splitter Inside splice tray look: 24 core/tray, 4pcs trays Stainless steel accessory Complete installation accessory for wall mounting(holding-pole accessory should contact sales) Specification of TGJS-303A Splitter Type Fiber Optic Splice Closure Dimension（mm） 380×245×130 Max. capacity(Single fiber) 16 Weight（kg） 4.5~5 Sealing type Mechanical Cable ports 1 input cable port for un-cut cable from diameter from10~17.5mm. 2 output cable ports for cable diameter from 8~17.5mm. 16 output cable ports for cable diameter less than 4mm. Single splice tray capacity(Single fiber) 16 Splice tray quantity 2pcs Packing And Comments Of TGJS-303A Splitter Type Fiber Optic Splice Closure This equipment packaging produced by TUOLIMA is moisture-proof and earthquake- proof. The accessories are packed first plastic bags, then into the boxes with plastic bags for sealing. There are moisture-proof and earthquake direction signs outside the boxes. It can't be inverted in the transport and be free from rolling when carrying. Please load carefully and prevent the collision. You should prevent it from heavy rain before installation. The temperature in the transport should be controlled between-35℃ to +55℃. The excessive accumulation of goods should be stored on the cartons. The treasury should away from the erosion of corrosive gas equipment and the temperature should be below 45℃ and higher than -5℃, and relative temperature should not be high in long-term(generally less than 75%). Package dimensions(W*H*D) 520mm*420mm*330mm Package material Standard carton for sea shipping or air express Weight 4.5kgs

As a fiber optic products supplier in the industry, TUOLIMA focuses on brand customization, multi-selective product logo printing, high-end and independent packaging design, to provide customers with a one-stop service that is quite trusted by professionals worldwide. Here are the steps to use the high precision fiber optical cleaver tool: 1. The light fiber plate cover open, open plate single core optical fiber fixture, confirm the knife in front of side position. 2. The optical fiber is placed in the V slot of the single-core optical fiber fixture, and the optical fiber coating is applied to remove the scale alignment of the boundary line and the fixture according to the required cutting length. (for example, when cutting the length of 16mm, the boundary line is aligned with the 16mm of the scale), it is time to confirm that the bare fiber section is straight. 3. On the cover of the single core fiber optic clamps to clamp the optical fiber. Close the cover of the optical fiber clamp, and push the knife to cut off the optical fiber. 4.Open the cover of the optical fiber and hold the fiber while holding down the cover of the single core fiber clamp and take out the optical fiber. The Trouble shooting of TLM-01B Fiber Optic Cleaver Cut off the bad of the FTTH tool may be caused by the following reasons: when the fiber is placed on the cutting knife, the fiber is not straight. Please go straight to the optical fiber. the position of the blade is too high, please adjust the height of the blade. optical fiber control block with dust and other foreign materials, please clean the fiber control block. foreign matter such as dust cleaning blade. fiber dust and other foreign matter, please remove the fiber coating, carefully wipe the bare optical fiber part. Please contact the company's after- sales service department in a timely manner. Specification of TLM-01B Fiber Optic Cleaver We have many kinds of fiber optic cable cleaver of different specifications, for example, ofc cleaver, s09 fiber cleaver, single fiber cleaver, automatic fiber cleaver, splicing cleaver and so on. This fiber tool kit is of good quality. And the fiber optic cutter price and fiber cleaver blade price are very affordable for our customers. If you have any problem about the fiber cutter tool after receiving our products, please call us. 1 Bare fiber diameter 125um 2 Fiber core number Single core 3 Fiber coated diameter 0.25&0.9mm 4 Coating length Cutting length +18mm 5 Fiber Cleaver length 9-16mm(0.25mm) 10-16mm(0.9mm) 6 Cutting angle ≤0.5° 7 Blade life 48000 8 Size 56(W)*55(D)*48(H)mm 9 Weight 265g

As a fiber optic products supplier in the industry, TUOLIMA focuses on brand customization, multi-selective product logo printing, high-end and independent packaging design, to provide customers with a one-stop service that is quite trusted by professionals worldwide. TGJS-101 is one of the main equipment for user access points, applied for protective connection and distribution between two or more cables. The primary function of horizontal fiber optic splice enclosure is to connect distribution cable and indoor cable in the open air. This inline fiber optic splice closure is widely used in communication systems, cable TV, optical cable network systems and others by virtue of steady structure, good sealing performance and easy construction. As a professional fiber optic cable manufacturing company, TUOLIMA can customize the horizontal fiber optic splice closure according to your requirements. Details of TGJS-101 Inline Type Fiber Optic Splice Closure The body is made of high quality engineering plastic with good strength; 3.2 With good waterproof design, the fiber optical splice closure can be applied into underground and aerial. 3.3 Be equipped with 4 splice trays (each capacity is 12 cores) ; The maximum can be 96 core (8 PCS 12F black trays). 3.4 Excellent fiber routing design ensures the radius curvature of the fiber well and enough fiber storage space. Specification of TGJS-101 Inline Type Fiber Optic Splice Closure Model No. TGJS-101 Color Black Capacity 48/96 cores Protection Level IP68 Material PP+GF Inlet/outlet 2/2 Dimension(MM) 480*155*110 Weight（KG） 2.3

As a fiber optic products supplier in the world, TUOLIMA has been operating in the optical communication industry since 2009, mainly fabricating and selling various fiber optic cable and cable fittings, fiber optic splice closures, distribution boxes with all accessories, FTTH transmission equipment. Rack mount patch panel is a panel used for cable interconnections between communication facilities. This odf fiber optic patch panel integrates fiber splicing, fiber termination, fiber optic adapters & connectors together in a single unit. Fiber optic termination panel also works as a protective device to protect fiber optic connections from damage. However, fiber optic cable patch panel comes into different shapes and specifications. To choose the right fiber optic termination box rack mount is not an easy thing. There are various fiber patch panel connector types in our company, such as 24 port fibre patch panel. TUOLIMA provides various models of fibre optic patch panel for your different needs. Why Choose TUOLIMA Rack Mount Patch Panels 1.Competitive price: We are a manufacturer of all kinds of rack mount patch panels, ODF, cabinet which made of stainless steel, SMC or metal. 2.Quality guarantee: TUOLIMA selects high quality metal to inject, bend and paint it into different molds or all customized design which ensures best quality. 3.Efficient and responsible after-sales service: TUOLIMA owns an individual group of sales in charge of your complete purchase experience. Any quality problem, please find our contact, then your products will be carefully inspected and found it a satisfied solution.