Other Electronic Equipment

Coil Winding Machine Magnetic Tensioner Tensioner is a necessary factor for keeping consistent winding accuracy. Selecting better tensioner provides a sophisticated winding machine with best performance. Stabilized tensioner improves winding problems and enhances productivity. For example, stabilized tensioner causes no breaking of wire, raises operation rate, secures the value of resistance, and increases credibility of the product. Perfect layer winding leads to material cost cutting and easy adjustment. Therefore, time and cost for machine maintenance can be decreased. QIANHE Engineering has a wide range of tensioner types, from basic Magnetic type tensioners to servo motor tensioners. Descriptions The coil winding magnetic tensioner can be used for tension control during the winding process of various wires such as enameled wire, nylon wire, metal wire etc. It can be used to produce coils ,transformer ,stator , motor ,and some other products when specifically matching with the winding machine. Comparatively speaking, this tensioner has a simple structure and low cost. It is one of the most widely used tensioners on the market. Features: Because of the non-contact method, stable tension can be obtained on a long- term basis. 2. Adoption of ferrite magnet, is a variation of the product is very low. 3. Have excellent follow-up with respect to high-speed winding. 4. To back tension can be adjusted freely, the windings of the square-shaped bobbin, it is also compatible with rapid change in the winding speed, does not have to be disconnected. 5. Tension is easy to set by direct reading scale with dial. 6.Disconnection of course, disconnection detection device which automatically stop the winding machine even if the wire is no longer is standard equipment. Model List Describe Model Tension Range (g) Wire Range (mm) Tension Arm Weight (kg) MTQ Series Horizontal Type QH-MTQSS 6-120 0.025-.012 CX- 1#,2# 0.5 QH-MTQ300S 14-400 0.06-0.25 CX-3#,4#,5# 0.55 QH-MTQS 30-800 0.08-0.40 CX-6#,7# 0.58 QH-MTQM 300-1500 0.35-0.8 CX-8# 0.8 Wire pass drawing Lightweight Wire 0.35-0.8mm Coil Winding Tensioner For Produce Air Core Coils 0 Picture show: Lightweight Wire 0.35-0.8mm Coil Winding Tensioner For Produce Air Core Coils 1 Lightweight Wire 0.35-0.8mm Coil Winding Tensioner For Produce Air Core Coils 2 Lightweight Wire 0.35-0.8mm Coil Winding Tensioner For Produce Air Core Coils 3 Motor Industry Inner Stator Winding Mechanical Tensioner Qh - Mtas Wire 0.08-.040mm All products have to pass strict inspection before packing ! Why do you choose us? 1.100% manufacturer In hardware tools, the wire winding machine training industry has more than 10 years of experience, we have more than and 100 skilled workers. 2. competitive price One-stop service, from the material of die cutting process, production, QC, packaging, delivery. We are sure we produce all the goods. And the quality is 100% rest assured. Many customers are very happy to cooperate with us, because we can provide a more competitive price as a factory. 3,The best choice of material All of our goods are the best material from the best suppliers, whether the material is qualified can be checked. 4. Quality Control Before shipment, there are specialized personnel checks, each product in the packaging before the inspection is qualified. We guarantee that each product shipment is perfect for sale. 5. Good service We promise to answer your question in 24 hours.

0.95 W/mK Chomerics T725 replacing high performance ZIITEK thermal conductive PCM phase change materials T725P For IGBTs T725P series is low melting point thermal interface material. At 50℃, T725P series begins to soften and flow, filling the microscopic irregularities of both the thermal solution and the integrated circuit package surface, thereby reducing thermal resistance.T725P series is a flexible solid at room temperature and freestanding without reinforcing components that reduce thermal performance. T725P Series shows no thermal performance degradation after 1,000 hours@130℃,or after 500 cycles, from -25℃ to 125℃.The material softens and does not fully change state resulting in minimal migration (pump out)at operating temperatures. Applications Include: > High Frequency Microprocessors > Notebook and Desktop PCs > Computer Serves > Memory Modules > Cache Chips > IGBTs Features: For Lowest Thermal Resistance : > 0.014℃-in² /W thermal resistance > Naturally tacky at room temperature, no adhesive required > No heat sink preheating required Typical Properties of T725P Series Product Name TICTM805P Testing standards Color Pink Visual Composite Thickness 0.005" (0.126mm) Thickness Tolerance ±0.0008" (±0.019mm) Density 2.2g/cc Helium Pycnometer Work Temperature -25℃～125℃ 　 phase transition temperature 50℃~60℃ 　 Thermal conductivity 0.95 W/mK ASTM D5470 (modified) Thermal lmpedance @ 50 psi(345 KPa) 0.024℃-in²/W ASTM D5470 (modified) 0.15℃-cm²/W Standard Thicknesses: 0.005"(0.127mm) Standard Sizes: 10" x 16"(254mm x 406mm) 16" X 400' (406mm X 121.92M) TIC™800 series are supplied with a white release paper and a bottom liner. TIC800™ series is available in kiss cut an extended pull tab liner or individual die cut shapes. Peressure Sensitive Adhesive: Peressure Sensitive Adhesive is not applicable for TIC™800 series products. Reinforcement: No reinforcement is necessary. 0.95 W/mK Chomerics T725 replacing ZIITEK Thermal Conductive PCM Phase Change Materials T725P For IGBTs 0 Why Choose us ? 1.Our value message is'' Do it right the First time, total quality control''. 2.Our core competencies is thermal conductive interface materials 3.Competitive advantage products. 4.Condidentiality agreement Bussiness Secrect Contract 5.Free sample offer 6.Quality assurance contract

PSA Nitrogen Generator, With Carbon Molecular Sieve Sorbent, Industrial Application PSA Nitrogen Generator Principles: PSA nitrogen generator uses a carbon molecular sieve as sorbent and produces nitrogen by making use of the PSA principle. Under certain pressure, a carbon molecular sieve has different oxygen/nitrogen adsorption capacity, i.e. much more oxygen adsorption capacity than nitrogen adsorption capacity. PLC controls the pneumatic valve on/off to realize two towers alternate adsorption and desorption as per pressure change, carries out oxygen/nitrogen separation, and produces nitrogen with desired purity. PSA Nitrogen Generator incorporates one air compressor, refrigerant air dryer and filters, main nitrogen generator, air buffer tank, and nitrogen buffer tank. With higher nitrogen pressure required, one BROTIE totally oil-free nitrogen compressor will be equipped after the nitrogen generator to increase the nitrogen pressure to the required pressure. Compressed air is purified through the air dryer and filters to a certain level for the main generator to work with. Air buffer is incorporated for a smooth supply of compressed air thus reducing the fluctuation of work demand for air compressors. The generator produces nitrogen with PSA (pressure swing adsorption) technology, a time-proven nitrogen generation method. Nitrogen with a desired purity is delivered to a nitrogen buffer tank for a smooth supply of product gas. Nitrogen in the buffer tank is maintained at 6barg pressure. After a totally oil-free nitrogen compressor, the pressure will be compressed to the required pressure. It is adjustable for you to adjust the outlet pressure by a pressure regulator valve, so that it can be used for your specific use. PSA Nitrogen Generator Details 95%-99.9999% purity 3-3000Nm3/Hour capacity Dew point: ≤-40 Air source pressure: 0.8-1.0Mpa Nitrogen-making pressure: 0.1-0.75Mpa Oxygen content:500ppm-3ppm Water content:5-20ppm Material Carbon steel, Stainless steel 304 NOTICE The following parameters, drawings, and photos are only for your reference. The final accurate product information will be supplied with the quotation packages. Industrial PSA Nitrogen Generator With Carbon Molecular Sieve Sorbent 0 Brief Principles Each gas has a characteristic adsorption rate when adsorbed by Carbon Molecular Sieve (CMS). CMS has a large surface area containing a volume of micro pores and passageways. Oxygen has a higher adsorption rate than nitrogen. When compressed air enters CMS, nitrogen molecules are able to pass through this large surface. And oxygen molecules are adsorbed to the surface area. As the CMS is saturated with oxygen, it should be depressurized to regenerate for the next cycle. We use two towers filled with CMS to produce a continuous stream of nitrogen. During depressurization, the nitrogen of lower purity than required is transferred to another tower called pressure equalization. Pressure equalization donates to higher efficiency and less energy consumption. Know-how in the definite time and ways to equalize the pressure is the key to the best results. PSA Nitrogen Generator Manufacturer Professional When the process adopts lifting air, oxygen and nitrogen have different diffusion rate and adsorptive capacity to separate oxygen from nitrogen on a carbon molecular sieve(CMS). When air is compressed to 0.8MPa, the air source enters in pressure-swing adsorption tower for separation after being purified through the dry and oil-water separation process (filter). Oxygen molecules are diffused and adsorbed in a carbon molecular sieve under pressure. Non-adsorbed nitrogen is discharged from the outlet of the adsorption tower. Oxygen is desorbed, discharged, and purged in an adsorption tower under depressurization. Moreover, adsorbents can be recycled. Paige brand. PSA Nitrogen Generator Specifications: No Model Capacity(Nm3/h) , Purity Power(KW) Overall size(mm) 1 2 3 4 PN-3-39 PN-5-29 PN-5-295 PN , -8-295 3 5 5 8 , 99.9% 99.5% 99% 95% 0.5 1800*1400*1500 5 6 7< , br> 8 PN-5-49 PN-8-39 PN-1 , 2-295 PN-15-29 5 8 12< , br> 15 99.99% 99.9% 99.5%< , br> 99% 0.5 1800*1400*1800 9 10 1 , 1 12 PN-10-49 PN-15-39 PN-25-295 PN-30-39 10 15 , 25 30 99.99% 99.9% 99.5% 99% 0.5 2000*1700*2250 13 14 , 15 16 PN-15-49 PN-22-39 PN-35-295 PN-45-29 15 22 35 45 99.99% 99.9% 99.5% 99% 0.5 2100*1800*220 , 0 17 18 19 20 P , N-20-49 PN-30-39 PN-50-295 PN , -60-29 20 30 50 60 , 99.99% 99.9% 99.5% 99% 0.5 2200*1800*2200 21 22 , 23 24 PN-30-49 PN-45- , 39 PN-75-295 PN-88-29 30 < , br>45 75 88 99.99% 99. , 9% 99.5% 99% 0.5 2400* , 1900*2200 25 26 27 28< , br> PN-40-49 PN-60-39 PN-100-295< , br> PN-120-29 40 60 100 120 99.99% 99.9% 99.5% 99% 0.5 2500*2100*2500 , 29 30 31 32 PN-50-49 PN-70-39 PN-120-295 PN-140-29< , br> 50 70 120 140 9 , 9.99% 99.9% 99.5% 99% 0.5 2600*2200*2850 33 34 , 35 36 PN-60-49 PN-90-39 PN-160-295 PN-190-29 60 90< , br> 160 190 99.99% 99.9% 99.5% 99% 0.5 2800*2200*2500 37 PN-80-49 80 99.99% 0.5 38 39 40 PN-120-39 PN-200-295 PN-250-29 120 200 250 99.9% 99.5% 9 , 9% 0.5 3200*1400*2800 41 42 , 43 44 PN-100-49 PN-140-39 , PN-250-295 PN-290-29 100 , 140 250 290 99.99% 99. , 9% 99.5% 99% 0.5 3500*1500*2800 ... ... ... ... ... ... Note , :More news please free to contact Since Gas System Co.,Ltd or send email to us directly

PRODUCT DESCRIPTION HX4HFW325 300min Load 4KG Pod 4.6m Wing Length UAV Security Mapping Inspection 5000m Flight Altitude Industrial Drone Multipurpose The HX4HFW325 can carry a variety of payloads. Therefore, it can be applied to a wide range of tasks, including surveying and mapping, inspection, monitoring, public safety, oil and gas pipeline inspection, etc. Mount 2-4KG Industrial loads such as drone pods, cameras, PTZ, surveying and mapping equipment, and thermal imaging cameras can be mounted according to different scenarios. Industrial Drone with fully autonomous flying VTOL Take off with one key, work efficiently Without operator intervention, the UAV automatically completes task cruise, flight state transition, vertical take-off and landing Real-time signal transmission VTOL cooperates with the ground station and image transmission equipment to realize the timely transmission of images, providing reliable guarantee for different working scenarios. Autopilot Full coverage of models with centimeter-level positioning accuracy Satellite navigation Real-time differential GPS/GLONASS/Galileo/BDS multi-system signal reception High security Oil-driven active power provides a higher safety factor Set emergency landing and parachute double protection Oil-driven fixed-wing UAV application field Aerial survey, police patrol, forest fire prevention, aerial surveying and mapping, power pipeline line-finding, environmental protection detection, disaster detection, aerial law enforcement, road and railway hydraulic measurement, 3D imaging, etc. Keep updating We will listen to customer feedback and keep updating our products. It keeps our technology and craftsmanship always at the leading position of industrial drones. Parameter Configuration HX4HFW325 Drone Name HX4HFW325 Industrial Drone Battery Life 3-5hours Wings Length 4.6m Cruise Speed 23- 26s/m . Task Load 2-4kg Drone Length 2.22m Practical Ceiling 5500m Wind Resistance Level 6 Battery Life 4-6h Motor Wheelbase 1.5m Route Accuracy 1. High Precision 1. Flight Radius 280km Stall Speed 40km/h Number of Waypoints 6400 point Power Type Gasoline hybrid Image Transmission SD video transmission 30 kilometers Maximum take-off weight 30KG 300min Load 4KG Pod 4.6m Wing Length UAV Mapping Inspection Drone VTOL HX4HFW325 0 300min Load 4KG Pod 4.6m Wing Length UAV Mapping Inspection Drone VTOL HX4HFW325 1300min Load 4KG Pod 4.6m Wing Length UAV Mapping Inspection Drone VTOL HX4HFW325 2 FAQ for Product & Brand Customization Q1. Can you customize according to my requested industrial drone parameters? A: Yes. We have the support of the entire industry chain of industrial drones, so we can not only carry out the R&D, design, and production of industrial drones according to your requirements, but also give you many constructive suggestions based on our past case experience. Q2. Can I make a sample order for custom drone? A: Yes, we welcome sample order to test and check out quality. Different samples in an order are acceptable. Q3. Is it OK to print my logo on product? A: Yes. Q4. What about the lead time? A:Sample needs 7-10 days. Q5. Do you have any MOQ limit for drone? A: We don't have any MOQ, 1piece is acceptable. Q6. How do you ship the order and how long does it take to arrive? A: We usually ship by air transportation. It takes around 7-12 days to arrive in most situations. Sea transportation is also available. Q7. How to make an order for drone? Step1: Let us know your requirements. Step2: We quote according to your requirements or our suggestions. Step3: Customer confirms the order and places deposit for formal order. Step4: We arrange the production. 300min Load 4KG Pod 4.6m Wing Length UAV Mapping Inspection Drone VTOL HX4HFW325 3

Product Description HVAC Thermostat , Programmable Thermostat , Room Temperature Digital Room Thermostat ISO certifications .pdf Parameter : Name: E7-L Temperature Range (°C): 0°C-40°C in 0.1°C Control Temp.Range (°C): 5°C-35°C in 0.5°C Switchable Voltage: 230 V AC; 50 Hz Switchable Current: 6 A (2 A inductive load) Programmability: Programmable Temp.Meas.Accuracy: ±1°C (at 20°C) Defrosting Temperature: +7°C Power Method: 2 x AA 1.5V Lithium batteries Switch: HEAT/OFF/COOL MODE Switch Dimensions: 130 x 80 x 28 mm Features: 1. Large LCD display with backlight ; 2. Permanent user setting retention during power loss ; 3. Can control valve and boiler at the same time; 4. Optional type of control for different heating application including room thermostat; floor thermostat or room thermostat with floor limitation; 5. Optional programming Period: 7 individual day programming with 48 separate time to select economic or comfort mode.(Every half hour as a period of time) /cancel the programming function. Packaging: 1. Inner package:Chinese/English/neutral package,special requirements based on clients. 2. Outer package:standard exporting package,special requirements based on clients. 3. One pcs per box. 4. Professional Perfomance Thermostat supplier. 5. 1 pcs in a color box, 8 pcs in a inner box, 2 inner boxes into one outer carton. 230VAC Digital Programmable HVAC Thermostat For Room 0

Micro Tubular Brass Coil Heater With Super Thin Wall 1.5mm 1. Product introduction Press in brass coil heater, the coil heater is designed to beset in the brass sheating, can eliminate known problems associated with the casting process. The machined path in the brass for the heater enables exact repeatability of heat profile. By never exposing the coil heater to molten brass there are no risks of shifted heater coils, or destruction of the thermocouple junction.Flexible design options include internal, external "wound in" or external slotted type J or type K thermocouples. 2. Characteristics 1) Has quick heat dissipation, high insulation, greatly extend the service life of heater 2) Can be built with a Micro, Mini, Flat, Low profile, or Round Nexthermal Coil Heater. 3) Safety in use 4) Faster responding heater due to eliminated air pockets than cast in brass 5) Profile and heater orientation precisely repeatable 6) Thermocouple not exposed to molten brass temperatures – Improved durability 7) Potential for designing thin walled brass heaters to minimize OD impact 8) Faster responding heater due to eliminated air pockets than cast in brass 3. Features: 1) Standard sizes available with various cross section 2) Various Watt Density options available. 3) Robust Design with Choice of Terminal Exits 4) Available with built in Thermocouple 5) Designed for even heat profile. 6) Precision fit on Hot Runner Nozzles & Manifolds. 7) Highly Non-corrosive. 8) Maximum heat transfer due to more contact area. 9) Advanced Thermal Engineering. 4. Application 1) Injection moulding machine nozzle 2) Hot Runner Nozzles & Bushings 3) Packaging machineries 4) Hot runner Injection moulds. 5) Blow Moulding Machine Nozzles. 6) PET prefrom & Thin wall container Moulds 7) Hot runner Manifolds. Parameters are required to place an order ! Custom Micro Tubular Brass Coil Heater With Super Thin Wall 1.5mm

Product Description EOD Robot Model: HW-18 Description Mechanical arm can clamp specimen weighing 30KG to be test as below in intermediate speed circularly. Each test should be conducted continuously in continuous working time and charging during working is not allowed. The continuous working time is 3 hours. Moving ability: EOD robot can move 10 minutes clockwise and anticlockwise respectively along square track of 10m X 10m. Grade ability: On the slope whose length is more than four times of robot length and incline is more than 40° with horizontal ground, operating robot climb to top of slope and return the same way, round-trip time can last 10 minutes. Mechanical arm function: Repeated operation of driving each mechanical arm joint separately to run continuously between two limit position, can last 30 minutes. Technical Parameter Robot Body Materials Aircraft-grade aluminum alloy, precision machining Dimensions L*W*H: 910 * 650 * 500 mm Weight 90kg (without accessories, package and control box) Battery DC24V lead acid rechargeable battery Working time ≥ 3 hours Maximum Speed ≥1.2m/s Loading Capacity When loading 140KG, it can move normally (actual measurement). Lift Capability It can move with clamping weights of 40K and will not drop (actual measurement). Grade Ability It can climb up the slope of 45° and stop steadily on the slope. Climbing Stairs Ability With traction-free assist, it can climb up and down the stairs of 160mm step height and 45°angle slope. Turning Ability In horizontal cement ground or bituminous pavement, the robot can turn clockwise or anticlockwise 360º. Limited Passage Width ≤700mm Over-obstacle Capacity It can cross the obstacle of 320mm height. Max. Mechanical Arms Spread 1650mm Gripper of Manipulator Maximum Expansion Range 250mm Arm Extension when stretch out and draw back 500mm Control Distance Wireless control: ≥150m (visible range); wire control: 100m (optional 200m); Forward Camera Color infrared induction Backward Camera Color infrared induction Cradle Head Various focal Camera Color infrared induction Manipulator Gripper Camera Color infrared induction Floodlight Two group LED floodlight (one group on the front and back) Control Terminal Box Portable, waterproof, dustproof, high strength Size ≤ L 460 * W 370 *H 260 mm Weight ≤ 10kg Display Screen 12-inch HB LCD, wide viewing angle, outdoor clear picture Operation High-quality rocker handle, human software interface design, easy observation and convenient operation Display Image It can monitor 4 video signals simultaneously or separately amplify one of 4 video signals Battery Rechargeable 24V lithium battery, working time ≥ 3 hours when fully charged. 360 Degrees Turning EOD Robot 0 Company Introduction In 2008, Beijing Hewei Yongtai Technology Co., LTD was established in Beijing.Focus on the development and operation of special safety equipment, mainly serve the public security law, armed police, military, customs and other national security departments. In 2010, Jiangsu Hewei Police Equipment Manufacturing Co., LTD was established in Guannan.Covering an area of 9000 square meters of workshop and office building, it aims to build a first-class special safety equipment research and development base in China. In 2015, a military-police Reserch and development center was set up in Shenzhen.Focus on the development of special safety equipment, has developed more than 200 kinds of professional safety equipment. Jiangsu Factory 360 Degrees Turning EOD Robot 1 360 Degrees Turning EOD Robot 2 Shenzhen Research Centre 360 Degrees Turning EOD Robot 3 360 Degrees Turning EOD Robot 4 Overseas Exhibitions 360 Degrees Turning EOD Robot 5 360 Degrees Turning EOD Robot 6 Certificates 360 Degrees Turning EOD Robot 7 360 Degrees Turning EOD Robot 8 360 Degrees Turning EOD Robot 9 Staff Photo Staff from Jiangsu Factory 360 Degrees Turning EOD Robot 10 Staff from Headquarters 360 Degrees Turning EOD Robot 11 Staff from Shenzhen research centre 360 Degrees Turning EOD Robot 12

Single Phase Silicon Rubber Lightning and Power Surge Arrester for Electrical Equipment Specifications: Composite Surge Arresters can be applied to a variety of systems including substation equipment, AC-DC converters, railway power system and power distribution units ranging from 0.25kV to 765kV systems. These surge arresters demonstrate excellent protection properties. Metal oxide type surge arresters offer such special features inherent in the gap-less structure, such as a quick response to surge voltage, high energy dissipation capability, safe operation, compactness / lightweight and freedom from pollution. Type YH5W5-21/56 Rated voltage---------kV 21 MOCV ----------------kV 16 Nominal Current-------kV 5 Residual voltage of steep impulse----at 5kA(kV) 60.5 8/20µS Residual voltage of lightning impulse current kV(Peak value)-----at 5kA(kV) 56 Residual voltage of switching impulse current kV (peak value)----at 1kA (kV) 46 1mA D.C reference voltage (kV) 29.7 Line discharge level 1 2mS long duration impulse current A 200 4/10µS High current impulse kA 65 Lightning impulse withstand kV 125 Power frequency voltage withstand(dry/wet)kV 43 0.1S TOV--------------kV 25.2 1S TOV----------------kV 24.15 10S TOV---------------kV 23.1 1200S TOV-------------kV 21 Creepage distance ----mm 670 Material employed in series non-linear resistor Zinc Oxide Competitive Advantage: 1. Compact and Lightweight 2. Extremely Safe Pressure Relief Performance 3. Superior Performance against Environmental Contamination 4. Directly Molded Structure 5. Compliance with International Standards(IEC60099-4) 6. Simple Support Structure 7. Manufactured at Advanced ISO-9001 certified facilities Other: Yongde holds the quality policy of being 'the technical forerunner, supreme in quality, supremacy of customers, and innovative progressing', so that our products and services successfully satisfied our users. We warmly welcome friends and customers from home and abroad to contact for exchanges and corporations. We also welcome feedbacks from our user communities.

Brand: General Electric PLC Item NO.: IC697PWR710 Order(MOQ): 1 Payment: T/T Market Price: 999 Price Range: 1 - 5 Product Origin: USA Color: Depends on material Shipping Port: XIAMEN Lead Time： IN STOCK

Minimum Order: 1 bags

Brand: General Electric PLC Item NO.: IC693MDL740 Order(MOQ): 1 Payment: T/T Market Price: 999 Price Range: 1 - 5 Product Origin: USA Color: Depends on material Shipping Port: XIAMEN Lead Time： IN STOCK

Minimum Order: 1 bags

Brand: General Electric PLC Item NO.: IC670CHS001 Order(MOQ): 1 Payment: T/T Market Price: 999 Price Range: 1 - 5 Product Origin: USA Color: Depends on material Shipping Port: XIAMEN Lead Time： IN STOCK

Minimum Order: 1 bags

Brand: General Electric PLC Item NO.: IC697CPX772 Order(MOQ): 1 Payment: T/T Market Price: 999 Price Range: 1 - 5 Product Origin: USA Color: Depends on material Shipping Port: XIAMEN Lead Time： IN STOCK

Minimum Order: 1 bags

Brand: General Electric PLC Item NO.: IC698ETM001 Order(MOQ): 1 Payment: T/T Market Price: 999 Price Range: 1 - 5 Product Origin: USA Color: Depends on material Shipping Port: XIAMEN Lead Time： IN STOCK

Minimum Order: 1 bags

Brand: General Electric PLC Item NO.: IC698CPE010 Order(MOQ): 1 Payment: T/T Market Price: 999 Price Range: 1 - 5 Product Origin: USA Color: Depends on material Shipping Port: XIAMEN Lead Time： IN STOCK

Minimum Order: 1 bags